- 03 Aug, 2015 29 commits
-
-
Boris BREZILLON authored
commit 60c3bc1f upstream. read_buf is called in place of write_buf in the nand_write_page_raw_syndrome function. Signed-off-by:
Boris BREZILLON <b.brezillon.dev@gmail.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Cc: Mason <slash.tmp@free.fr> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Brian Norris authored
commit bd9c6e99 upstream. Use a repeated read_byte() instead of read_buf(), since for x16 buswidth devices, we need to avoid the upper I/O[16:9] bits. See the following commit for reference: commit 05f78359 Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Date: Thu Dec 5 22:22:04 2013 +0100 mtd: nand: don't use {read,write}_buf for 8-bit transfers Now, I think that all barriers to probing ONFI on x16 devices are removed, so remove the check from nand_flash_detect_onfi(). Tested on 8-bit ONFI NAND (Micron MT29F32G08CBADAWP). Signed-off-by:
Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Tested-By:
Pekon Gupta <pekon@ti.com> Cc: Mason <slash.tmp@free.fr> Signed-off-by:
-
Thomas Petazzoni authored
commit ea78b951 upstream. There was a mistake in the definition of the functions for MPP48 on Marvell Armada XP. The second function is dev(clkout), and not tclk. Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Fixes: 463e270f ("pinctrl: mvebu: add pinctrl driver for Armada XP") Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Thomas Petazzoni authored
commit 80b3d04f upstream. The latest version of the Armada XP datasheet no longer documents the VDD cpu_pd functions, which might indicate they are not working and/or not supported. This commit ensures the pinctrl driver matches the datasheet. Signed-off-by:
-
Thomas Petazzoni authored
commit bc99357f upstream. After updating to a more recent version of the Armada XP datasheet, we realized that some of the pins documented as having a NAND-related functionality in fact did not have such functionality. This commit updates the pinctrl driver accordingly. Signed-off-by:
-
Thomas Petazzoni authored
commit 438881df upstream. Due to a mistake, the CS0 and CS1 SPI0 functions were incorrectly named "spi0-1" instead of just "spi0". This commit fixes that. This DT binding change does not affect any of the in-tree users. Signed-off-by:
-
Lukasz Majewski authored
commit 26bb0e9a upstream. It turns out that some boards can have instance->lower greater than 0 and when thermal trend is dropping it results with next_target equal to -1. Since the next_target is defined as unsigned long it is interpreted as 0xFFFFFFFF and larger than instance->upper. As a result the next_target is set to instance->upper which ramps up to maximal cooling device target when the temperature is steadily decreasing. Signed-off-by:
Lukasz Majewski <l.majewski@samsung.com> Signed-off-by:
Zhang Rui <rui.zhang@intel.com> Cc: Mason <slash.tmp@free.fr> Signed-off-by:
-
Uwe Kleine-König authored
commit e5babdf9 upstream. Since commit bd31b859 (which is in 3.2-rc1) nw_gpio_lock is a raw spinlock that needs usage of the corresponding raw functions. This fixes: drivers/mtd/maps/dc21285.c: In function 'nw_en_write': drivers/mtd/maps/dc21285.c:41:340: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type spin_lock_irqsave(&nw_gpio_lock, flags); In file included from include/linux/seqlock.h:35:0, from include/linux/time.h:5, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/mtd/maps/dc21285.c:8: include/linux/spinlock.h:299:102: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *' static inline raw_spinlock_t *spinlock_check(spinlock_t *lock) ^ drivers/mtd/maps/dc21285.c:43:25: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type spin_unlock_irqrestore(&nw_gpio_lock, flags); ^ In file included from include/linux/seqlock.h:35:0, from include/linux/time.h:5, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/mtd/maps/dc21285.c:8: include/linux/spinlock.h:370:91: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *' static inline void spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags) Fixes: bd31b859 ("locking, ARM: Annotate low level hw locks as raw") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Brian Norris authored
commit 073db4a5 upstream. On A MIPS 32-cores machine a BUG_ON was triggered because some acesses to mtd->usecount were done without taking mtd_table_mutex. kernel: Call Trace: kernel: [<ffffffff80401818>] __put_mtd_device+0x20/0x50 kernel: [<ffffffff804086f4>] blktrans_release+0x8c/0xd8 kernel: [<ffffffff802577e0>] __blkdev_put+0x1a8/0x200 kernel: [<ffffffff802579a4>] blkdev_close+0x1c/0x30 kernel: [<ffffffff8022006c>] __fput+0xac/0x250 kernel: [<ffffffff80171208>] task_work_run+0xd8/0x120 kernel: [<ffffffff8012c23c>] work_notifysig+0x10/0x18 kernel: kernel: Code: 2442ffff ac8202d8 000217fe <00020336> dc820128 10400003 00000000 0040f809 00000000 kernel: ---[ end trace 080fbb4579b47a73 ]--- Fixed by taking the mutex in blktrans_open and blktrans_release. Note that this locking is already suggested in include/linux/mtd/blktrans.h: struct mtd_blktrans_ops { ... /* Called with mtd_table_mutex held; no race with add/remove */ int (*open)(struct mtd_blktrans_dev *dev); void (*release)(struct mtd_blktrans_dev *dev); ... }; But we weren't following it. Originally reported by (and patched by) Zhang and Giuseppe, independently. Improved and rewritten. Reported-by:
Zhang Xingcai <zhangxingcai@huawei.com> Reported-by:
Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Tested-by:
Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by:
-
Grygorii Strashko authored
commit 084609bf upstream. Setting a dev_pm_ops suspend/resume pair of callbacks but not a set of hibernation callbacks means those pm functions will not be called upon hibernation - that leads to system crash on ARM during freezing if gpio-led is used in combination with CPU led trigger. It may happen after freeze_noirq stage (GPIO is suspended) and before syscore_suspend stage (CPU led trigger is suspended) - usually when disable_nonboot_cpus() is called. Log: PM: noirq freeze of devices complete after 1.425 msecs Disabling non-boot CPUs ... ^ system may crash or stuck here with message (TI AM572x) WARNING: CPU: 0 PID: 3100 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x22c/0x370() 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in Supervisor mode during Functional access CPU1: shutdown ^ or here Fix this by using SIMPLE_DEV_PM_OPS, which appropriately assigns the suspend and hibernation callbacks and move led_suspend/led_resume under CONFIG_PM_SLEEP to avoid build warnings. Fixes: 73e1ab41 (leds: Convert led class driver from legacy pm ops to dev_pm_ops) Signed-off-by:
Grygorii Strashko <Grygorii.Strashko@linaro.org> Acked-by:
Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Axel Lin authored
commit 63781394 upstream. request_any_context_irq() returns a negative value on failure. It returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED on success. So fix testing return value of request_any_context_irq(). Also fixup the return value of devm_request_any_context_irq() to make it consistent with request_any_context_irq(). Fixes: 0668d306 ("genirq: Add devm_request_any_context_irq()") Signed-off-by:
Axel Lin <axel.lin@ingics.com> Reviewed-by:
Stephen Boyd <sboyd@codeaurora.org> Link: http://lkml.kernel.org/r/1431334978.17783.4.camel@ingics.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Bart Van Assche authored
commit 535fb906 upstream. Avoid that srp_terminate_io() can get invoked while srp_queuecommand() is in progress. This patch avoids that an I/O timeout can trigger the following kernel warning: WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:1447 srp_terminate_io+0xef/0x100 [ib_srp]() Call Trace: [<ffffffff814c65a2>] dump_stack+0x4e/0x68 [<ffffffff81051f71>] warn_slowpath_common+0x81/0xa0 [<ffffffff8105204a>] warn_slowpath_null+0x1a/0x20 [<ffffffffa075f51f>] srp_terminate_io+0xef/0x100 [ib_srp] [<ffffffffa07495da>] __rport_fail_io_fast+0xba/0xc0 [scsi_transport_srp] [<ffffffffa0749a90>] rport_fast_io_fail_timedout+0xe0/0xf0 [scsi_transport_srp] [<ffffffff8106e09b>] process_one_work+0x1db/0x780 [<ffffffff8106e75b>] worker_thread+0x11b/0x450 [<ffffffff81073c64>] kthread+0xe4/0x100 [<ffffffff814cf26c>] ret_from_fork+0x7c/0xb0 See also patch "scsi_transport_srp: Add transport layer error handling" (commit ID 29c17324). Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: James Bottomley <JBottomley@Odin.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Bart Van Assche authored
commit be34c62d upstream. Introduce the helper function srp_wait_for_queuecommand(). Move the definition of scsi_request_fn_active(). Add a comment above srp_wait_for_queuecommand() that support for scsi-mq needs to be added. This patch does not change any functionality. A second call to srp_wait_for_queuecommand() will be introduced in the next patch. Signed-off-by:
-
Ezequiel Garcia authored
commit ea6055c4 upstream. Since commit 39a6ac11 ("spi/pl022: Devicetree support w/o platform data") the 'num-cs' parameter cannot be passed through platform data when probing with devicetree. Instead, it's a required devicetree property. Fix the binding documentation so the property is properly specified. Fixes: 39a6ac11 ("spi/pl022: Devicetree support w/o platform data") Signed-off-by:
Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Martin Sperl authored
commit 8e76ef88 upstream. Fix a race (with some kernel configurations) where a queued master->pump_messages runs and frees dummy_tx/rx before spi_unmap_msg is running (or is finished). This results in the following messages: BUG: Bad page state in process page:db7ba030 count:0 mapcount:0 mapping: (null) index:0x0 flags: 0x200(arch_1) page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set ... Reported-by:
Noralf Trønnes <noralf@tronnes.org> Suggested-by:
Martin Sperl <kernel@martin.sperl.org> Signed-off-by:
-
Stefan Wahren authored
commit a7068e39 upstream. The buffer for condtraints debug isn't big enough to hold the output in all cases. So fix this issue by increasing the buffer. Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
-
Maxime Coquelin authored
commit 921cc294 upstream. The way the mask is generated in regmap_field_init() is wrong. Indeed, a field initialized with msb = 31 and lsb = 0 provokes a shift overflow while calculating the mask field. On some 32 bits architectures, such as x86, the generated mask is 0, instead of the expected 0xffffffff. This patch uses GENMASK() to fix the problem, as this macro is already safe regarding shift overflow. Signed-off-by:
Maxime Coquelin <maxime.coquelin@st.com> Signed-off-by:
-
Arun Chandran authored
commit 15b8d2c4 upstream. In big endian mode regmap_bulk_read gives incorrect data for byte reads. This is because memcpy of a single byte from an address after full word read gives different results when endianness differs. ie. we get little-end in LE and big-end in BE. Signed-off-by:
Arun Chandran <achandran@mvista.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit 3836785a upstream. If there is a PM QoS latency limit and all of the sufficiently shallow C-states are disabled, the cpuidle menu governor returns 0 which on some systems is CPUIDLE_DRIVER_STATE_START and shouldn't be returned if that C-state has been disabled. Fix the issue by modifying the menu governor to return (-1) in such situations. Signed-off-by:
Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com> Signed-off-by:
-
Will Deacon authored
commit 6f1a6ae8 upstream. When building the kernel with a bare-metal (ELF) toolchain, the -shared option may not be passed down to collect2, resulting in silent corruption of the vDSO image (in particular, the DYNAMIC section is omitted). The effect of this corruption is that the dynamic linker fails to find the vDSO symbols and libc is instead used for the syscalls that we intended to optimise (e.g. gettimeofday). Functionally, there is no issue as the sigreturn trampoline is still intact and located by the kernel. This patch fixes the problem by explicitly passing -shared to the linker when building the vDSO. Reported-by:
Szabolcs Nagy <Szabolcs.Nagy@arm.com> Reported-by:
James Greenlaigh <james.greenhalgh@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Dave P Martin authored
commit b9bcc919 upstream. The memmap freeing code in free_unused_memmap() computes the end of each memblock by adding the memblock size onto the base. However, if SPARSEMEM is enabled then the value (start) used for the base may already have been rounded downwards to work out which memmap entries to free after the previous memblock. This may cause memmap entries that are in use to get freed. In general, you're not likely to hit this problem unless there are at least 2 memblocks and one of them is not aligned to a sparsemem section boundary. Note that carve-outs can increase the number of memblocks by splitting the regions listed in the device tree. This problem doesn't occur with SPARSEMEM_VMEMMAP, because the vmemmap code deals with freeing the unused regions of the memmap instead of requiring the arch code to do it. This patch gets the memblock base out of the memblock directly when computing the block end address to ensure the correct value is used. Signed-off-by:
Dave Martin <Dave.Martin@arm.com> Signed-off-by:
-
Catalin Marinas authored
commit 565630d5 upstream. After secondary CPU boot or hotplug, the active_mm of the idle thread is &init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1 and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the TTBR0_EL1 is already set to the reserved value, there is no need to perform any context reset. Signed-off-by:
-
Vineet Gupta authored
commit d57f7272 upstream. When auditing cmpxchg call sites, Chuck noted that gcc was optimizing away some of the desired LDs. | do { | new = old = *ipi_data_ptr; | new |= 1U << msg; | } while (cmpxchg(ipi_data_ptr, old, new) != old); was generating to below | 8015cef8: ld r2,[r4,0] <-- First LD | 8015cefc: bset r1,r2,r1 | | 8015cf00: llock r3,[r4] <-- atomic op | 8015cf04: brne r3,r2,8015cf10 | 8015cf08: scond r1,[r4] | 8015cf0c: bnz 8015cf00 | | 8015cf10: brne r3,r2,8015cf00 <-- Branch doesn't go to orig LD Although this was fixed by adding a ACCESS_ONCE in this call site, it seems safer (for now at least) to add compiler barrier to LLSC based cmpxchg Reported-by:
Chuck Jordan <cjordan@synopsys.com> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit b064a8fa upstream. Commit 73f7d1ca "ACPI / init: Run acpi_early_init() before timekeeping_init()" moved the ACPI subsystem initialization, including the ACPI mode enabling, to an earlier point in the initialization sequence, to allow the timekeeping subsystem use ACPI early. Unfortunately, that resulted in boot regressions on some systems and the early ACPI initialization was moved toward its original position in the kernel initialization code by commit c4e1acbb "ACPI / init: Invoke early ACPI initialization later". However, that turns out to be insufficient, as boot is still broken on the Tyan S8812 mainboard. To fix that issue, split the ACPI early initialization code into two pieces so the majority of it still located in acpi_early_init() and the part switching over the platform into the ACPI mode goes into a new function, acpi_subsystem_init(), executed at the original early ACPI initialization spot. That fixes the Tyan S8812 boot problem, but still allows ACPI tables to be loaded earlier which is useful to the EFI code in efi_enter_virtual_mode(). Link: https://bugzilla.kernel.org/show_bug.cgi?id=97141 Fixes: 73f7d1ca "ACPI / init: Run acpi_early_init() before timekeeping_init()" Reported-and-tested-by:
Marius Tolzmann <tolzmann@molgen.mpg.de> Signed-off-by:
Toshi Kani <toshi.kani@hp.com> Reviewed-by:
Hanjun Guo <hanjun.guo@linaro.org> Reviewed-by:
Lee, Chun-Yi <jlee@suse.com> Signed-off-by:
-
Takashi Iwai authored
commit 4df3fd17 upstream. Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of the two headphones, thus the driver tries to assign another as the line-out, and this results in the inconsistent mapping between the created jack ctl and the actual I/O. Due to this, PulseAudio doesn't handle it properly and gets the silent output. The fix is to ignore the non-HP sequencer checks. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99681Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 7819717b upstream. Acer Aspire V5 with ALC282 codec needs the similar quirk like Dell laptops to support the headset mic. The headset mic pin is 0x19 and it's not exposed by BIOS, thus we need to fix the pincfg as well. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201Signed-off-by:
-
Ryan Underwood authored
commit 2fb22a80 upstream. Disable write buffering on the Toshiba ToPIC95 if it is enabled by somebody (it is not supposed to be a power-on default according to the datasheet). On the ToPIC95, practically no 32-bit Cardbus card will work under heavy load without locking up the whole system if this is left enabled. I tried about a dozen. It does not affect 16-bit cards. This is similar to the O2 bugs in early controller revisions it seems. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55961Signed-off-by:
Ryan C. Underwood <nemesis@icequake.net> Signed-off-by:
Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by:
-
Brian King authored
commit 45c44b5f upstream. Increase the default init stage change timeout from 15 seconds to 30 seconds. This resolves issues we have seen with some adapters not transitioning to the first init stage within 15 seconds, which results in adapter initialization failures. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Paul E. McKenney authored
commit 6e91f8cb upstream. If, at the time __rcu_process_callbacks() is invoked, there are callbacks in Tiny RCU's callback list, but none of them are ready to be invoked, the current list-management code will knit the non-ready callbacks out of the list. This can result in hangs and possibly worse. This commit therefore inserts a check for there being no callbacks that can be invoked immediately. This bug is unlikely to occur -- you have to get a new callback between the time rcu_sched_qs() or rcu_bh_qs() was called, but before we get to __rcu_process_callbacks(). It was detected by the addition of RCU-bh testing to rcutorture, which in turn was instigated by Iftekhar Ahmed's mutation testing. Although this bug was made much more likely by 915e8a4f (rcu: Remove fastpath from __rcu_process_callbacks()), this did not cause the bug, but rather made it much more probable. That said, it takes more than 40 hours of rcutorture testing, on average, for this bug to appear, so this fix cannot be considered an emergency. Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by:
Josh Triplett <josh@joshtriplett.org> Signed-off-by:
-
- 10 Jul, 2015 11 commits
-
-
Greg Kroah-Hartman authored
-
David E. Box authored
commit aa8e4f22 upstream. Fixes an error in having the iosf build as 'default m'. On X86 SoC's the iosf sideband is the only way to access information for some registers, as opposed to through MSR's on other Intel architectures. While selecting IOSF_MBI is preferred, it does mean carrying extra code on non-SoC architectures. This exports the selection to the user, allowing those driver writers to compile out iosf code if it's not being built. Signed-off-by:
David E. Box <david.e.box@linux.intel.com> Link: http://lkml.kernel.org/r/1409175640-32426-2-git-send-email-david.e.box@linux.intel.comSigned-off-by:
H. Peter Anvin <hpa@linux.intel.com> Cc: William Dauchy <william@gandi.net> Signed-off-by:
-
Christoffer Dall authored
commit ae705930 upstream. [Note the upstream one of this patch requires applying full GICv3 support but it's out of the scope of stable kernel. So this patch has a huge modification for stable kernel comparing to the upstream one.] There is an interesting bug in the vgic code, which manifests itself when the KVM run loop has a signal pending or needs a vmid generation rollover after having disabled interrupts but before actually switching to the guest. In this case, we flush the vgic as usual, but we sync back the vgic state and exit to userspace before entering the guest. The consequence is that we will be syncing the list registers back to the software model using the GICH_ELRSR and GICH_EISR from the last execution of the guest, potentially overwriting a list register containing an interrupt. This showed up during migration testing where we would capture a state where the VM has masked the arch timer but there were no interrupts, resulting in a hung test. Cc: Marc Zyngier <marc.zyngier@arm.com> Reported-by:
Alex Bennee <alex.bennee@linaro.org> Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Shannon Zhao <shannon.zhao@linaro.org> Signed-off-by:
-
Marc Zyngier authored
commit 04b8dc85 upstream. [Since we don't backport commit c6473555 (KVM: arm: Add initial dirty page locking support) for linux-3.14.y, there is no stage2_wp_range in arch/arm/kvm/mmu.c. So ignore the change in stage2_wp_range introduced by this patch.] The kernel's pgd_index macro is designed to index a normal, page sized array. KVM is a bit diffferent, as we can use concatenated pages to have a bigger address space (for example 40bit IPA with 4kB pages gives us an 8kB PGD. In the above case, the use of pgd_index will always return an index inside the first 4kB, which makes a guest that has memory above 0x8000000000 rather unhappy, as it spins forever in a page fault, whist the host happilly corrupts the lower pgd. The obvious fix is to get our own kvm_pgd_index that does the right thing(tm). Tested on X-Gene with a hacked kvmtool that put memory at a stupidly high address. Reviewed-by:
-
Marc Zyngier authored
commit 801f6772 upstream. Commit b856a591 (arm/arm64: KVM: Reset the HCR on each vcpu when resetting the vcpu) moved the init of the HCR register to happen later in the init of a vcpu, but left out the fixup done in kvm_reset_vcpu when preparing for a 32bit guest. As a result, the 32bit guest is run as a 64bit guest, but the rest of the kernel still manages it as a 32bit. Fun follows. Moving the fixup to vcpu_reset_hcr solves the problem for good. Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Marc Zyngier authored
commit 55e858b7 upstream. It took about two years for someone to notice that the IPA passed to TLBI IPAS2E1IS must be shifted by 12 bits. Clearly our reviewing is not as good as it should be... Paper bag time for me. Reported-by:
Mario Smarduch <m.smarduch@samsung.com> Tested-by:
-
Christoffer Dall authored
commit 05971120 upstream. [Note this patch is a bit different from the original one as the names of vgic_initialized and kvm_vgic_init are different.] It is curently possible to run a VM with architected timers support without creating an in-kernel VGIC, which will result in interrupts from the virtual timer going nowhere. To address this issue, move the architected timers initialization to the time when we run a VCPU for the first time, and then only initialize (and enable) the architected timers if we have a properly created and initialized in-kernel VGIC. When injecting interrupts from the virtual timer to the vgic, the current setup should ensure that this never calls an on-demand init of the VGIC, which is the only call path that could return an error from kvm_vgic_inject_irq(), so capture the return value and raise a warning if there's an error there. We also change the kvm_timer_init() function from returning an int to be a void function, since the function always succeeds. Reviewed-by:
-
Eric W. Biederman authored
commit ceeb0e5d upstream. Limit the mounts fs_fully_visible considers to locked mounts. Unlocked can always be unmounted so considering them adds hassle but no security benefit. Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Eric W. Biederman authored
commit 93e3bce6 upstream. The warning message in prepend_path is unclear and outdated. It was added as a warning that the mechanism for generating names of pseudo files had been removed from prepend_path and d_dname should be used instead. Unfortunately the warning reads like a general warning, making it unclear what to do with it. Remove the warning. The transition it was added to warn about is long over, and I added code several years ago which in rare cases causes the warning to fire on legitimate code, and the warning is now firing and scaring people for no good reason. Reported-by:
Ivan Delalande <colona@arista.com> Reported-by:
Omar Sandoval <osandov@osandov.com> Fixes: f48cfddc ("vfs: In d_path don't call d_dname on a mount point") Signed-off-by:
-
Jan Kara authored
commit 2426f391 upstream. file_remove_suid() could mistakenly set S_NOSEC inode bit when root was modifying the file. As a result following writes to the file by ordinary user would avoid clearing suid or sgid bits. Fix the bug by checking actual mode bits before setting S_NOSEC. Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Radim Krčmář authored
commit 42720138 upstream. Writes were a bit racy, but hard to turn into a bug at the same time. (Particularly because modern Linux doesn't use this feature anymore.) Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> [Actually the next patch makes it much, much easier to trigger the race so I'm including this one for stable@ as well. - Paolo] Signed-off-by:
-
