The patch adds driver interface for reading the config attributes from user
provided buffer, and updates these values on nvm config flash partition.

This is basically an expansion of our existing ethtool -f implementation.
The management FW has exposed an additional method of configuring some of
the nvram options, and this makes use of that. This implementation will
come into use when newer FW files which contain configuration directives
employing this API will be provided to ethtool -f.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds API for configuring the NVM config attributes using
Management FW (MFW) interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-5.4-20190814' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2019-08-14

this is a pull request for net-next/master consisting of 41 patches.

The first two patches are for the kvaser_pciefd driver: Christer Beskow
removes unnecessary code in the kvaser_pciefd_pwm_stop() function,
YueHaibing removes the unused including of <linux/version.h>.

In the next patch YueHaibing also removes the unused including of
<linux/version.h> in the f81601 driver.

In the ti_hecc driver the next 6 patches are by me and fix checkpatch
warnings. YueHaibing's patch removes an unused variable in the
ti_hecc_mailbox_read() function.

The next 6 patches all target the xilinx_can driver. Anssi Hannula's
patch fixes a chip start failure with an invalid bus. The patch by
Venkatesh Yadav Abbarapu skips an error message in case of a deferred
probe. The 3 patches by Appana Durga Kedareswara rao fix the RX and TX
path for CAN-FD frames. Srinivas Neeli's patch fixes the bit timing
calculations for CAN-FD.

The next 12 patches are by me and several checkpatch warnings in the
af_can, raw and bcm components.

Thomas Gleixner provides a patch for the bcm, which switches the timer
to HRTIMER_MODE_SOFT and removes the hrtimer_tasklet.

Then 6 more patches by me for the gw component, which fix checkpatch
warnings, followed by 2 patches by Oliver Hartkopp to add CAN-FD
support.

The vcan driver gets 3 patches by me, fixing checkpatch warnings.

And finally a patch by Andre Hartmann to fix typos in CAN's netlink
header.
====================

__page_pool_get_cached() will return NULL when the ring is
empty, even if there are pages present in the lookaside cache.

It is also possible to refill the cache, and then return a
NULL page.

Restructure the logic so eliminate both cases.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Gerd Rausch says:

====================
net/rds: Fixes from internal Oracle repo

This is the first set of (mostly old) patches from our internal repository
in an effort to synchronize what Oracle had been using internally
with what is shipped with the Linux kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Original commit from 2011 updated to include a change by
Yuval Shaia <yuval.shaia@oracle.com>
that adds a new statistic counter "send_stuck_rm"
to capture the messages looping exessively
in the send path.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a previous commit, fields were added to "struct rds_statistics"
but array "rds_stat_names" was not updated accordingly.

Please note the inconsistent naming of the string representations
that is done in the name of compatibility
with the Oracle internal code-base.

s_recv_bytes_added_to_socket     -> "recv_bytes_added_to_sock"
s_recv_bytes_removed_from_socket -> "recv_bytes_freed_fromsock"

Fixes: 192a798f ("RDS: add stat for socket recv memory usage")
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Bang Nguyen <bang.nguyen@oracle.com>
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Signed-off-by: Somasundaram Krishnasamy <somasundaram.krishnasamy@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will kick the RDS worker thread if we have been looping
too long.

Original commit from 2012 updated to include a change by
Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
that triggers "must_wake" if "rds_ib_recv_refill_one" fails.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
netdevsim: implement support for devlink region and snapshots

Implement devlink region support for netdevsim and test it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Test netdevsim devlink region implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement dummy region of size 32K and allow user to create snapshots
or random data using debugfs file trigger.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
selftests: netdevsim: add devlink paramstests

The first patch is just a helper addition as a dependency of the actual
test in patch number two.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Test recently added netdevsim devlink param implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Push the jq return value workaround code into a separate helper so it
could be used by the rest of the code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove variable initializations in functions that
are followed by assignments before use
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sync EEE init for RTL8168h with vendor driver and add two writes to
vendor-specific registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: realtek: map vendor-specific EEE registers to standard MMD registers

EEE-related registers on newer integrated PHY's have the standard
layout, but are accessible not via MMD but via vendor-specific
registers. Emulating the standard MMD registers allows to use the
generic functions for EEE control and to significantly simplify
the r8169 driver.

v2:
- rebase patch 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that the Realtek PHY driver maps the vendor-specific EEE registers
to the standard MMD registers, we can remove all special handling and
use the generic functions phy_ethtool_get/set_eee.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

EEE-related registers on newer integrated PHY's have the standard
layout, but are accessible not via MMD but via vendor-specific
registers. Emulating the standard MMD registers allows to use the
generic functions for EEE control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the genphy driver binds to a swphy it will call
genphy_read_abilites that will try to read MII_ESTATUS if BMSR_ESTATEN
is set in MII_BMSR. So far this would read the default value 0xffff
and 1000FD and 1000HD are reported as supported just by chance.
Better add explicit support for emulating MII_ESTATUS.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Value of MII_CTRL1000 is needed only if LPA_1000MSFAIL is set.
Therefore move reading this register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support of the socket options RDS6_INFO_SOCKETS and
RDS6_INFO_RECV_MESSAGES which update the RDS_INFO_SOCKETS and
RDS_INFO_RECV_MESSAGES options respectively.  The old options work
for IPv4 sockets only.
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tx_done_tasklet tasklet is used in invoke the hrtimer
(mvpp2_hr_timer_cb) in softirq context. This can be also achieved without
the tasklet but with HRTIMER_MODE_SOFT as hrtimer mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for net-next.
This round addresses fallout from previous pull request:

1) Remove #warning from ipt_LOG.h and ip6t_LOG.h headers,
   from Jeremy Sowden.

2) Incorrect parens in memcmp() in nft_bitwise, from Nathan Chancellor.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

clang warns:

net/netfilter/nft_bitwise.c:138:50: error: size argument in 'memcmp'
call is a comparison [-Werror,-Wmemsize-comparison]
        if (memcmp(&priv->xor, &zero, sizeof(priv->xor) ||
                                      ~~~~~~~~~~~~~~~~~~^~
net/netfilter/nft_bitwise.c:138:6: note: did you mean to compare the
result of 'memcmp' instead?
        if (memcmp(&priv->xor, &zero, sizeof(priv->xor) ||
            ^
                                                       )
net/netfilter/nft_bitwise.c:138:32: note: explicitly cast the argument
to size_t to silence this warning
        if (memcmp(&priv->xor, &zero, sizeof(priv->xor) ||
                                      ^
                                      (size_t)(
1 error generated.

Adjust the parentheses so that the result of the sizeof is used for the
size argument in memcmp, rather than the result of the comparison (which
would always be true because sizeof is a non-zero number).

Fixes: bd8699e9 ("netfilter: nft_bitwise: add offload support")
Link: https://github.com/ClangBuiltLinux/linux/issues/638Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

There are two netfilter userspace headers which contain deprecation
warnings.  While these headers are not used within the kernel, they are
compiled stand-alone for header-testing.

Pablo informs me that userspace iptables still refer to these headers,
and the intention was to use xt_LOG.h instead and remove these, but
userspace was never updated.

Remove the warnings.

Fixes: 2a475c40 ("kbuild: remove all netfilter headers from header-test blacklist.")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Realtek provided information on how the new NIC-integrated PHY's
expose whether they support 2.5G/5G/10G. This allows to automatically
differentiate 1Gbps and 2.5Gbps PHY's, and therefore allows to
remove the fake PHY ID mechanism for RTL8125.
So far RTL8125 supports 2.5Gbps only, but register layout for faster
modes has been defined already, so let's use this information to be
future-proof.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Holger reported sporadic transmit timeouts and it turned out that one
path misses ringing the doorbell. Fix was suggested by Eric.

Fixes: ef143585 ("r8169: make use of xmit_more")
Suggested-by: Eric Dumazet <edumazet@google.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS updates for net-next

The following patchset contains Netfilter/IPVS updates for net-next:

1) Rename mss field to mss_option field in synproxy, from Fernando Mancera.

2) Use SYSCTL_{ZERO,ONE} definitions in conntrack, from Matteo Croce.

3) More strict validation of IPVS sysctl values, from Junwei Hu.

4) Remove unnecessary spaces after on the right hand side of assignments,
   from yangxingwu.

5) Add offload support for bitwise operation.

6) Extend the nft_offload_reg structure to store immediate date.

7) Collapse several ip_set header files into ip_set.h, from
   Jeremy Sowden.

8) Make netfilter headers compile with CONFIG_KERNEL_HEADER_TEST=y,
   from Jeremy Sowden.

9) Fix several sparse warnings due to missing prototypes, from
   Valdis Kletnieks.

10) Use static lock initialiser to ensure connlabel spinlock is
    initialized on boot time to fix sched/act_ct.c, patch
    from Florian Westphal.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Hayes says:

====================
v2:
For patch #2, replace list_for_each_safe with list_for_each_entry_safe.
Remove unlikely in WARN_ON. Adjust the coding style.

For patch #4, replace list_for_each_safe with list_for_each_entry_safe.
Remove "else" after "continue".

For patch #5. replace sysfs with ethtool to modify rx_copybreak and
rx_pending.

v1:
The different chips use different rx buffer size.

Use skb_add_rx_frag() to reduce memory copy for RX.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Let the rx_copybreak and rx_pending could be modified by
ethtool.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Use skb_add_rx_frag() to reduce the memory copy for rx data.

Use a new list of rx_used to store the rx buffer which couldn't be
reused yet.

Besides, the total number of rx buffer may be increased or decreased
dynamically. And it is limited by RTL8152_MAX_RX_AGG.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Replace kmalloc_node() with alloc_pages() for rx buffer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

The original method uses an array to store the rx information. The
new one uses a list to link each rx structure. Then, it is possible
to increase/decrease the number of rx structure dynamically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

The different chips may accept different rx buffer sizes. The RTL8152
supports 16K bytes, and RTL8153 support 32K bytes.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Heiner says:

====================
So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction and add needed helpers to phy-core.c

v2:
- remove unused parameter in patch 1
- rename __phy_speed_down to phy_speed_down_core in patch 2
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction by using new helper __phy_speed_down. New member adv_old
in struct phy_device is used by phy_speed_up to restore the advertised
modes before calling phy_speed_down. Don't simply advertise what is
supported because a user may have intentionally removed modes from
advertisement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

phy_speed_down_core provides most of the functionality for
phy_speed_down. It makes use of new helper phy_resolve_min_speed that is
based on the sorting of the settings[] array. In certain cases it may be
helpful to be able to exclude legacy half duplex modes, therefore
prepare phy_resolve_min_speed() for it.

v2:
- rename __phy_speed_down to phy_speed_down_core
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

We will need the functionality of __set_linkmode_max_speed also for
linkmode bitmaps other than phydev->supported. Therefore split it.

v2:
- remove unused parameter from __set_linkmode_max_speed
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>