The new connection parameters now match the recommended values for
Proximity and Health Thermometer profiles. The previous values were
ramdomly chosen, and are either too low or too high for most cases.

New values:

Scan Interval: 60 ms
Scan Window: 30 ms
Minimum Connection Interval: 50 ms
Maximum Connection Interval: 70 ms
Supervision Timeout: 420 ms

See "Table 5.2: Recommended Scan Interval and Scan Window Values" and
"Table 5.3: Recommended Connection Interval Values" for both profiles
for details. Note that the "fast connection" parameters were chosen,
because we do not support yet dynamically changing these parameters from
initiator side.

Additionally, the Proximity profile recommends (section "4.4 Alert on
Link Loss"):

"It is recommended that the Link Supervision Timeout (LSTO) is set to 6x
the connection interval."

Minimum_CE_Length and Maximum_CE_Length were also changed from 0x0001 to
0x0000 because they are informational and optional, and old value was
not reflecting reality.
Signed-off-by: Anderson Lizardo <anderson.lizardo@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Use sk_buff fragment capabilities to link together incoming skbs
instead of allocating a new skb for reassembly and copying.

The new reassembly code works equally well for ERTM and streaming
mode, so there is now one reassembly function instead of two.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

ERTM reassembly will be more efficient when skbs are linked together
rather than copying every incoming data byte. The existing stream recv
function assumes skbs are linear, so it needs to know how to handle
fragments before reassembly is changed.

bt_sock_recvmsg() already handles fragmented skbs.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Fragmented skbs are only encountered when receiving ERTM or streaming
mode L2CAP data.  BNEP, CMTP, HIDP, and RFCOMM generally use basic
mode, but they need to handle fragments without crashing.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Removed tests which prevent transmission of ACL packets
when the device is in HCI_RAW mode. These tests verified that
there are ACL or LE links currently tracked by the HCI
connection manager. However, a HCI_RAW mode device does not
use the connection manager. In these circumstances, the connection
counts will be zero, and thus, transmitted ACL packets dropped.

The acl_num test is actually a vestige of a previous bulk URB
scheme that is no longer used by this driver (bulk URBs were not
started until at least one ACL connection was created). This was
incompatible with some endpoint implementations and was dropped -
see commit 43c2e57f.

The utility of these tests is marginal - currently, the hci tx
scheduler cannot send an ACL or LE packet for an untracked connection
(except if the device is in HCI_RAW mode).

Lastly, no other transport layer driver enforces these same tests.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

l2cap_create_iframe_pdu is only used in l2cap_core.c
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

The mgmt_device_found event will be used to report LE devices found
during discovery procedure. Since LE advertising reports events
doesn't have class of device information, we need to check if
'dev_class' is not NULL before copying it.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This patch reduces the critial region (protected by hdev->lock) in
hci_cc_le_set_scan_enable(). This way, only really required code is
synchronized.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This patch fixes wrong memcpy size when copying rand value to
HCI_OP_LE_START_ENC command.
The compiler pretends that the array parameter was declared as a pointer
and sizeof reports the size of the pointer. [1]

[1] http://www.c-faq.com/aryptr/aryparmsize.htmlSigned-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Anderson Lizardo <anderson.lizardo@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

For now, only the LTK is properly supported. We are able to receive
and generate the other types of keys, but we are not able to use
them. So it's better not request them to be distributed.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

For slave initiated security, we should set a default security level,
for now BT_SECURITY_MEDIUM.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This reverts commit 5a0a8b49.

If we use separate messages and list for SMP specific keys we can
simplify the code.

Conflicts:

	net/bluetooth/mgmt.c
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

When receiving a security request from the remote device we should find
if there is already a LTK associated with the remote device, if found
we should use it to encrypt the link.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Until we support any pairing method (Passkey Entry, OOB) that gives
MITM protection we shouldn't send that we have MITM protection.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Add management interface events for blocking/unblocking a device.
Sender of the block device command gets cmd complete and other
mgmt sockets get the event. Event is also sent to mgmt sockets when
blocking is done with ioctl, e.g when blocking a device with
hciconfig. This makes it possible for bluetoothd to track status
of blocked devices when a third party block or unblocks a device.

Event sending is handled in mgmt_device_blocked function which gets
called from hci_blacklist_add in hci_core.c. A pending command is
added in mgmt_block_device, so that it can found when sending the
event - the event is not sent to the socket from which the pending
command came. Locks were moved out from hci_core.c to hci_sock.c
and mgmt.c, because locking is needed also for mgmt_pending_add in
mgmt.c.
Signed-off-by: Antti Julku <antti.julku@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This lifts the requirement of 16 digits pin codes when pairing
with devices that do not support SSP when using the mgmt interface.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

The HIGH security level requires a 16 digit pin code for non-SSP
bondings. Sometimes this requirement is not acceptable and we still
want protection againts MITM attacks (which is something that the
MEDIUM security level doesn't provide), for that we should allow
another way to request authentication without using the HIGH security
level.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

The function crypto_blkcipher_setkey() called by smp_e()
can sleep, so all the crypto work has to be moved to
hci_dev workqueue.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

The objective is to make the core to have as little as possible
information about SMP procedures and logic. Now, all the SMP
specific information is hidden from the core.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

During setup the host initializes all HID reports. Some devices do not
support this. If this quirk is set, we skip the initialization.
See also usbhid_init_reports() for this quirk.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Add LE link type as known connection type for debugfs stringizing
output.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Add command to management interface for enabling/disabling the
fast connectable mode.
Signed-off-by: Antti Julku <antti.julku@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

One piece of information that was lost when using the mgmt interface,
was the type of the connection. Using HCI events we used to know
the type of the connection based on the type of the event, e.g.
HCI_LE_Connection_Complete for LE links.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

When doing the pairing procedure we won't have an associated
socket, but we still have to do the SMP negotiation. This
adds support for encrypting the link and exchanging keys.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Using the advertising cache we are able to infer the type
of the remote device, and so trigger pairing over the correct
link type.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Add HCI_CONN_LE_SMP_PEND flag to indicate that SMP is pending
for that connection. This allows to have information that an SMP
procedure is going on for that connection.

We use the HCI_CONN_ENCRYPT_PEND to indicate that encryption
(HCI_LE_Start_Encryption) is pending for that connection.

While a SMP procedure is going on we hold an reference to the
connection, to avoid disconnections.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Each time a SMP command is enqueued, we reset the SMP timer,
this way we follow exactly what the spec mandates:

"The Security Manager Timer shall be reset when an L2CAP SMP command is
queued for transmission." Vol. 3, Part H, Section 3.4
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This checks if there is any existing connection according to its type
before start iterating in the list and immediately stop iterating when
reaching the number of connections.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Three drivers, rtl8192ce, rtl8192cu and rtl8192de, use the same macro
to check if a particular rate is in the CCK set. This common code is
relocated to a common header file. A distinct macro used by rtl8192se
with the same name is renamed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The various modparam messages are difficult to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The various modparam messages are difficult to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The various modparam messages are difficult to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

CCK/OFDM noise immunilty values are always reset to defaults
during bgscan. This could affect the link quality and
performance when the STA is associated in a noisy channel.
So do not override the learned values across the scanning.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The NFC Controller Interface (NCI) is a standard
communication protocol between an NFC Controller (NFCC)
and a Device Host (DH), defined by the NFC Forum.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The file nfc.h was moved from include/net to include/net/nfc,
since new NFC header files will be added to include/net/nfc.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add 2 new nfc control operations:
dev_up to turn on the nfc device
dev_down to turn off the nfc device
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211_conn_scan allows disabled channels at scan request.
Hence probe request was seen at the disabled one. This patch
ensures that disabled channel never be added into the scan
request's channel list.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>