The DDR support patch needs the following fixes:

- The block driver does not need to know about DDR, any more
  than it needs to know about bus width.
- Not only the card must be switched to DDR mode.  The host
  controller must also be configured, which is done through
  the 'set_ios()' function.
- Do not set the DDR mode state until after the switch command
  is successful.
- Setting block length is not supported in DDR mode.  Make that
  a core function and change the other place it is used (mmc_test)
  also.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Add support for Dual Data Rate MMC cards as defined in the 4.4
specification.
Signed-off-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

After discovering a problem in regulator reference counting I took Mark
Brown's advice to move the reference count into the MMC core by making the
regulator status a member of struct mmc_host.

I took this opportunity to also implement NULL versions of
the regulator functions so as to rid the driver code from
some ugly #ifdef CONFIG_REGULATOR clauses.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sundar Iyer <sundar.iyer@stericsson.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Cliff Brake <cbrake@bec-systems.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

mmc_rescan() includes a pr_info which prints 4 lines each second for
hosts configured with MMC_CAP_NEEDS_POLL. This patch enables the message
only if CONFIG_MMC_DEBUG is selected. Tested on i.MX51's sdhci-esdhc.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Chris Ball <cjb@laptop.org>

In the latest releases of the mmc driver, the freq during initialization
is set to a fixed 400 Khz.  This was reportedly too fast for several
users.  As there doesn't seem to be an ideal frequency
which-works-for-all, Pierre suggested to let the driver try several
frequencies.

This patch implements that idea. It will try mmc-initialization using
several frequencies from an array 400, 300, 200 and 100.

In case SDIO is broken, it'll still try to detect SDMEM, also at different
freqs.
Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es>
Cc: Pierre Ossman <pierre@ossman.eu>
Reviewed-by: Chris Ball <cjb@laptop.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: Ben Nizette <bn@niasdigital.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

When a controller requires SDHCI_QUIRK_BROKEN_CARD_DETECTION, we poll
for card insertion/removal, and that creates interrupts.  There's no
need to be doing this if we have a non-removable card.

This patch requires cards to be removable before we're willing to set
MMC_CAP_NEEDS_POLL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
[cjb: modified changelog and code indentation]
Signed-off-by: Chris Ball <cjb@laptop.org>

There are two checks that need to be made when determining whether a
card is removable. A host controller may set MMC_CAP_NONREMOVABLE if the
controller does not support removing cards (e.g. eMMC), in which case
the card is physically non-removable. Also the 'mmc_assume_removable'
module parameter can be configured at module load time, in which case
the card may be logically non-removable.

A helper function keeps the logic in one place so that code always
checks both conditions.

Because this new function is likely to be called from modules we now
need to export the mmc_assume_removable symbol.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

The EXTRA_CFLAGS assignment in mmc/Makefile was not accomplishing
anything because this flag only has effect on sources at the same level
as the makefile (i.e., per directory). Since card/, core/, and host/
rely on MMC_DEBUG, the subdir-ccflags-y variant seems to be the
appropriate choice.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

In a multi-controller environment it is helpful to know which controller
has problems.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

This patch is necessary to gain the performance boost from 8-bit data
with the sdhci-stm driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

MMC_CAP_MMC_HIGHSPEED allows MMC and eMMC to negotiate up to 50M
instead of the previous limit of 25M.
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

While we're at it, add symbols for SDHCI_MAX_DIV_SPEC_{200,300}.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

SDHC Spec 3.0: Capabilities Register bits[15-08] are Base Clock Frequency
      1.0/2.0: Capabilities Register bits[13-08] are Base Clock Frequency
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Michal Miroslaw <mirqus@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: David Vrabel <david.vrabel@csr.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

The "6882a8c0 sdhci: Add better ADMA error reporting" commit added
sdhci_show_adma_error() which is built when DEBUG is defined.  Since we
already have CONFIG_MMC_DEBUG used elsewhere in this driver, may as well
make consistent use of that config knob instead.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Append .5 to KiB display when there are an odd number of sectors.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Correctly allocate memory to meet the host controller
driver's maximum segment size and count limits.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

As proposed by Greg K-H it is more logical to keep files for the mmc_test
driver under debugfs.

Additionally this patch brings seq_file API for show() method.  It allows
to write unlimited data to the file.

Example of usage:
  # mount -t debugfs none /sys/kernel/debug
  # modprobe mmc_test
    [  581.395843] mmc_test mmc0:0001: Card claimed for testing.
  # echo 25 > /sys/kernel/debug/mmc0/mmc0\:0001/test
    [  604.568542] mmc0: Starting tests of card mmc0:0001...
    [  604.582733] mmc0: Test case 25. Best-case read performance into scattered pages...
    [  604.923553] mmc0: Transfer of 8192 sectors (4096 KiB) took 0.124664314 seconds (33644 kB/s, 32856 KiB/s)
    [  604.933227] mmc0: Result: OK
    [  604.936248] mmc0: Tests completed.
  # cat /sys/kernel/debug/mmc0/mmc0\:0001/test
    Test 25: 0
    1 8192 0.124664314 33644784
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Greg KH <greg@kroah.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Make it possible to get test results via sysfs.  It helps to do tests
non-interactively.  We have the file created under sysfs already and
can use it to show test results.

Prior to this patch, the "test" file under each card's sysfs node was
write-only, and results were obtained by looking at dmesg.  This patch
improves programmatic access to the test results, making them available by
reading back from the same "test" file:

[root@host mmc0:e624]# echo 6 > test
[root@host mmc0:e624]# cat test
Test 6: 2

[cjb@laptop.org: changelog improvements]
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

It's better to use strict_strtol() to convert user's input and strictly
check it. At least it forbids to interpret wrong input as a 0 and
prevents to run all tests.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

There are methods to check card type. Let's use them instead of direct checking
type bits.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

The host controller driver limits I/O transfers to maximum
transfer size, maximum block count, maximum segment size
and maximum segment count.  The performance tests were
not obeying these limits which meant they would not work
with some drivers.  This patch fixes that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Get rid of init_MUTEX[_LOCKED]() and use sema_init() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Chris Ball <cjb@laptop.org>

Global symbols should use their subsystem name in a prefixed fashion.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Conversion from struct device to struct mmc_card is used more than in one
place.  Due to this it's better to have public macro for such thing.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Fix an issue found by klockwork. Just paranoia.
Signed-off-by: JiebingLi <jiebing.li@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Add a driver for USB SD Host Controller devices.  These devices are
Cypress Astoria chips with firmware compliant with issue 2 of CSR's USHC
specification.

[cjb: adapt to block layer deprecation of max_{hw,phys}_segs]
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

We have deprecated the distinction between hardware and physical
segments in the block layer.  Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

[cjb: rebased patch against Linus]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <linux-mmc@vger.kernel.org>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

[cjb: rebased patch against Linus]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

[cjb: rebased patch against Linus]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2: (36 commits)
  nilfs2: eliminate sparse warning - "context imbalance"
  nilfs2: eliminate sparse warnings - "symbol not declared"
  nilfs2: get rid of bdi from nilfs object
  nilfs2: change license of exported header file
  nilfs2: add bdev freeze/thaw support
  nilfs2: accept 64-bit checkpoint numbers in cp mount option
  nilfs2: remove own inode allocator and destructor for metadata files
  nilfs2: get rid of back pointer to writable sb instance
  nilfs2: get rid of mi_nilfs back pointer to nilfs object
  nilfs2: see state of root dentry for mount check of snapshots
  nilfs2: use iget for all metadata files
  nilfs2: get rid of GCDAT inode
  nilfs2: add routines to redirect access to buffers of DAT file
  nilfs2: add routines to roll back state of DAT file
  nilfs2: add routines to save and restore bmap state
  nilfs2: do not allocate nilfs_mdt_info structure to gc-inodes
  nilfs2: allow nilfs_clear_inode to clear metadata file inodes
  nilfs2: get rid of snapshot mount flag
  nilfs2: simplify life cycle management of nilfs object
  nilfs2: do not allocate multiple super block instances for a device
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (47 commits)
  Blackfin: bfin_spi.h: add MMR peripheral layout
  Blackfin: bfin_ppi.h: start a common PPI/EPPI header
  Blackfin: bfin_can.h: add missing VERSION/VERSION2 MMRs
  Blackfin: bf538: add missing SIC_RVECT define
  Blackfin: bf561: rewrite SICA_xxx to just SIC_xxx
  Blackfin: bf54x: add missing SIC_RVECT definition
  Blackfin: H8606: move 8250 irqflags to platform resources
  Blackfin: glue XIP/ROM kernel kconfigs
  Blackfin: update sparse flags for latest upstream changes
  Blackfin: coreb: update ioctl numbers
  Blackfin: coreb: add gpl module license
  Blackfin: bf518-ezkit: add ssm2603 codec resources
  Blackfin: bf51x/bf52x: fix 16/32bit SPORT MMR helpers
  Blackfin: tll6527m: new board port
  Blackfin: bf526-ezbrd/bf527-ezkit: add NAND partition for u-boot
  Blackfin: merge kernel init memory back into main memory region
  Blackfin: gpio: add peripheral group check
  Blackfin: dma: bf54x: add missing break for SPORT1 TX IRQ
  Blackfin: add new cacheflush syscall
  Blackfin: bf548-ezkit: increase u-boot partition size
  ...

Merge branch 'x86-trampoline-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-trampoline-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86-32, mm: Add an initial page table for core bootstrapping

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
  kdb,debug_core: adjust master cpu switch logic against new debug_core locking
  debug_core: refactor locking for master/slave cpus
  x86,kgdb: remove unnecessary call to kgdb_correct_hw_break()
  debug_core: disable hw_breakpoints on all cores in kgdb_cpu_enter()
  kdb,kgdb: fix sparse fixups
  kdb: Fix oops in kdb_unregister
  kdb,ftdump: Remove reference to internal kdb include
  kdb: Allow kernel loadable modules to add kdb shell functions
  debug_core: stop rcu warnings on kernel resume
  debug_core: move all watch dog syncs to a single function
  x86,kgdb: fix debugger hw breakpoint test regression in 2.6.35

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
  USB: mct_u232: fix broken close
  USB: gadget: amd5536udc.c: fix error path
  USB: imx21-hcd - fix off by one resource size calculation
  usb: gadget: fix Kconfig warning
  usb: r8a66597-udc: Add processing when USB was removed.
  mxc_udc: add workaround for ENGcm09152 for i.MX35
  USB: ftdi_sio: add device ids for ScienceScope
  USB: musb: AM35x: Workaround for fifo read issue
  USB: musb: add musb support for AM35x
  USB: AM35x: Add musb support
  usb: Fix linker errors with CONFIG_PM=n
  USB: ohci-sh - use resource_size instead of defining its own resource_len macro
  USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
  USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
  USB: xhci: Fix compile error when CONFIG_PM=n
  USB: accept some invalid ep0-maxpacket values
  USB: xHCI: PCI power management implementation
  USB: xHCI: bus power management implementation
  USB: xHCI: port remote wakeup implementation
  USB: xHCI: port power management implementation
  ...

Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
  serial8250: ratelimit "too much work" error
  serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
  serial: abstraction for 8250 legacy ports
  serial/imx: check that the buffer is non-empty before sending it out
  serial: mfd: add more baud rates support
  jsm: Remove the uart port on errors
  Alchemy: Add UART PM methods.
  8250: allow platforms to override PM hook.
  altera_uart: Don't use plain integer as NULL pointer
  altera_uart: Fix missing prototype for registering an early console
  altera_uart: Fixup type usage of port flags
  altera_uart: Make it possible to use Altera UART and 8250 ports together
  altera_uart: Add support for different address strides
  altera_uart: Add support for getting mapbase and IRQ from resources
  altera_uart: Add support for polling mode (IRQ-less)
  serial: Factor out uart_poll_timeout() from 8250 driver
  serial: mark the 8250 driver as maintained
  serial: 8250: Don't delay after transmitter is ready.
  tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
  vcs: invoke the vt update callback when /dev/vcs* is written to
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (31 commits)
  driver core: Display error codes when class suspend fails
  Driver core: Add section count to memory_block struct
  Driver core: Add mutex for adding/removing memory blocks
  Driver core: Move find_memory_block routine
  hpilo: Despecificate driver from iLO generation
  driver core: Convert link_mem_sections to use find_memory_block_hinted.
  driver core: Introduce find_memory_block_hinted which utilizes kset_find_obj_hinted.
  kobject: Introduce kset_find_obj_hinted.
  driver core: fix build for CONFIG_BLOCK not enabled
  driver-core: base: change to new flag variable
  sysfs: only access bin file vm_ops with the active lock
  sysfs: Fail bin file mmap if vma close is implemented.
  FW_LOADER: fix kconfig dependency warning on HOTPLUG
  uio: Statically allocate uio_class and use class .dev_attrs.
  uio: Support 2^MINOR_BITS minors
  uio: Cleanup irq handling.
  uio: Don't clear driver data
  uio: Fix lack of locking in init_uio_class
  SYSFS: Allow boot time switching between deprecated and modern sysfs layout
  driver core: remove CONFIG_SYSFS_DEPRECATED_V2 but keep it for block devices
  ...

Commit dd3932ed ("block: remove BLKDEV_IFL_WAIT") had removed the
flag argument to blkdev_issue_flush(), but the ocfs2 merge brought in a
new one.  It didn't cause a merge conflict, so the merges silently
worked out fine, but the result didn't actually compile.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: (56 commits)
  [CIFS] move close processing  from cifs_close to cifsFileInfo_put
  cifs: convert cifs_tcp_ses_lock from a rwlock to a spinlock
  cifs: cancel_delayed_work() + flush_scheduled_work() -> cancel_delayed_work_sync()
  Clean up two declarations of blob_len
  cifs: move cifsFileInfo_put to file.c
  cifs: convert GlobalSMBSeslock from a rwlock to regular spinlock
  [CIFS] Fix minor checkpatch warning and update cifs version
  cifs: move cifs_new_fileinfo to file.c
  cifs: eliminate pfile pointer from cifsFileInfo
  cifs: cifs_write argument change and cleanup
  cifs: clean up cifs_reopen_file
  cifs: eliminate the inode argument from cifs_new_fileinfo
  cifs: eliminate oflags option from cifs_new_fileinfo
  cifs: fix flags handling in cifs_posix_open
  cifs: eliminate cifs_posix_open_inode_helper
  cifs: handle FindFirst failure gracefully
  NTLM authentication and signing - Calculate auth response per smb session
  cifs: don't use vfsmount to pin superblock for oplock breaks
  cifs: keep dentry reference in cifsFileInfo instead of inode reference
  cifs: on multiuser mount, set ownership to current_fsuid/current_fsgid (try #7)
  ...

Fix up trivial conflict in fs/cifs/cifsfs.c due to added/removed header files