We prefer to sort device nodes under simple bus in order of unit
address.  Let's sort the devices under lsio_subsys properly.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

We prefer to sort alias entries alphabetically, so let's move serial0
to the right place.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

lsio_mu13 node is used to communicate with DSP.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8MM has one wm8524 audio codec connected with
SAI3 digital audio interface.

This patch uses simple-card machine driver in order
to enable wm8524 codec.

We need to set:
	* SAI3 pinctrl configuration
	* codec reset gpio pinctrl configuration
	* clock hierarchy
	* codec node
	* simple-card configuration
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is for the development kit board for the Librem 5. The current level
of support yields a working console and is able to boot userspace from
the network or eMMC.

Additional subsystems that are active :

- Both USB ports
- SD card socket
- WiFi usdhc
- WWAN modem
- GNSS
- GPIO keys
- LEDs
- gyro
- magnetometer
- touchscreen
- pwm
- backlight
- haptic motor
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the qDMA device tree nodes for LS1028A devices
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable SNVS power key for i.MX8MQ EVK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

LS1028A has a SEC v5.0 compatible security engine.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add nxp sa56004 chip node for temperature monitor.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

usbphy nodes do not have any register properties and thus
shouldn't be placed inside the bus.

Move usbphy nodes from soc node to root node in order to fix
the following build warnings with W=1:

arch/arm64/boot/dts/freescale/imx8mm.dtsi:681.27-687.6: Warning (simple_bus_reg): /soc/bus@32c00000/usbphynop1: missing or empty reg/ranges property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:710.27-716.6: Warning (simple_bus_reg): /soc/bus@32c00000/usbphynop2: missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass the 'ranges' property for each one of the AIPS bus in order
to fix the following build warnings:

arch/arm64/boot/dts/freescale/imx8mm.dtsi:209.23-388.5: Warning (unit_address_vs_reg): /soc/bus@30000000: node has a unit name, but
no reg property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:390.23-439.5: Warning (unit_address_vs_reg): /soc/bus@30400000: node has a unit name, but
no reg property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:441.23-658.5: Warning (unit_address_vs_reg): /soc/bus@30800000: node has a unit name, but
no reg property
arch/arm64/boot/dts/freescale/imx8mm.dtsi:660.23-724.5: Warning (unit_address_vs_reg): /soc/bus@32c00000: node has a unit name, but
no reg property

This also aligns with imx8mq.dtsi.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'soc' name needs a unit name to match its 'ranges' property.

Pass the unit name in order to fix the following dtc build warning
with W=1:

arch/arm64/boot/dts/freescale/imx8mm.dtsi:203.6-754.4: Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name

This also aligns with imx8mq.dtsi.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a node for the snvs power key, "disabled" by default.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ls1028a platform uses sp805 watchdog, and use 1/16 platform clock as
timer clock, this patch fix device tree node.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Change the sata node to enable sata.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX8QXP ocotp node

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Anson Huang <anson.huang@nxp.com>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX system controller watchdog has pretimeout function which
depends on i.MX SCU driver, so it should be a subnode of SCU.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8MM has 5 SAI instances with the following base
addresses according to RM.

SAI1 base address: 3001_0000h
SAI2 base address: 3002_0000h
SAI3 base address: 3003_0000h
SAI5 base address: 3005_0000h
SAI6 base address: 3006_0000h
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds USB dt nodes for LS1028A.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX8QXP GPIO alias for kernel GPIO driver usage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX8MQ GPIO alias for kernel GPIO driver usage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Unnecessary blank lines do NOT help readability, so remove them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add nvmem-cells reference to cpu and fill the OPP table with all known
OPPs.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a nvmem cell on cpu node referencing speed grade and the 1.8 Ghz
cpufreq opp.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The BUCK2 regulator is used for cpufreq voltage control, otherwise
configuration is mostly static.

This uses the newly-implemented rohm,reset-snvs-powered property to
properly handle the SNVS state of imx8mm.

Between BD71837 and BD71847 the BUCK3/4 regulators were removed but
datasheet and board schematics kept the names for BUCK5/6/7/8. The
driver however renumbered 5/6/7/8 to 3/4/5/6. Use the names from DT
bindings and add comments to signal this.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a node for the irqsteer interrupt controller found on the iMX8MQ
SoC.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The LS1028A has a LCD controller and Displayport interface that
connects to eDP and Displayport connectors on the LS1028A board.

This patch enables the LCD controller driver on the LS1028A.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Wen He <wen.he_1@nxp.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull UBIFS fixes from Richard Weinberger:

 - build errors wrt xattrs

 - mismerge which lead to a wrong Kconfig ifdef

 - missing endianness conversion

* tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
  ubifs: Convert xattr inum to host order
  ubifs: Use correct config name for encryption
  ubifs: Fix build error without CONFIG_UBIFS_FS_XATTR

Merge yet more updates from Andrew Morton:
 "A few final bits:

   - large changes to vmalloc, yielding large performance benefits

   - tweak the console-flush-on-panic code

   - a few fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  panic: add an option to replay all the printk message in buffer
  initramfs: don't free a non-existent initrd
  fs/writeback.c: use rcu_barrier() to wait for inflight wb switches going into workqueue when umount
  mm/compaction.c: correct zone boundary handling when isolating pages from a pageblock
  mm/vmap: add DEBUG_AUGMENT_LOWEST_MATCH_CHECK macro
  mm/vmap: add DEBUG_AUGMENT_PROPAGATE_CHECK macro
  mm/vmalloc.c: keep track of free blocks for vmap allocation

Pull more Kbuild updates from Masahiro Yamada:

 - remove unneeded use of cc-option, cc-disable-warning, cc-ldoption

 - exclude tracked files from .gitignore

 - re-enable -Wint-in-bool-context warning

 - refactor samples/Makefile

 - stop building immediately if syncconfig fails

 - do not sprinkle error messages when $(CC) does not exist

 - move arch/alpha/defconfig to the configs subdirectory

 - remove crappy header search path manipulation

 - add comment lines to .config to clarify the end of menu blocks

 - check uniqueness of module names (adding new warnings intentionally)

* tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (24 commits)
  kconfig: use 'else ifneq' for Makefile to improve readability
  kbuild: check uniqueness of module names
  kconfig: Terminate menu blocks with a comment in the generated config
  kbuild: add LICENSES to KBUILD_ALLDIRS
  kbuild: remove 'addtree' and 'flags' magic for header search paths
  treewide: prefix header search paths with $(srctree)/
  media: prefix header search paths with $(srctree)/
  media: remove unneeded header search paths
  alpha: move arch/alpha/defconfig to arch/alpha/configs/defconfig
  kbuild: terminate Kconfig when $(CC) or $(LD) is missing
  kbuild: turn auto.conf.cmd into a mandatory include file
  .gitignore: exclude .get_maintainer.ignore and .gitattributes
  kbuild: add all Clang-specific flags unconditionally
  kbuild: Don't try to add '-fcatch-undefined-behavior' flag
  kbuild: add some extra warning flags unconditionally
  kbuild: add -Wvla flag unconditionally
  arch: remove dangling asm-generic wrappers
  samples: guard sub-directories with CONFIG options
  kbuild: re-enable int-in-bool-context warning
  MAINTAINERS: kbuild: Add pattern for scripts/*vmlinux*
  ...

Pull i2c updates from Wolfram Sang:
 "Some I2C core API additions which are kind of simple but enhance error
  checking for users a lot, especially by returning errno now.

  There are wrappers to still support the old API but it will be removed
  once all users are converted"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: add device-managed version of i2c_new_dummy
  i2c: core: improve return value handling of i2c_new_device and i2c_new_dummy

Pull ext4 fixes from Ted Ts'o:
 "Some bug fixes, and an update to the URL's for the final version of
  Unicode 12.1.0"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: avoid panic during forced reboot due to aborted journal
  ext4: fix block validity checks for journal inodes using indirect blocks
  unicode: update to Unicode 12.1.0 final
  unicode: add missing check for an error return from utf8lookup()
  ext4: fix miscellaneous sparse warnings
  ext4: unsigned int compared against zero
  ext4: fix use-after-free in dx_release()
  ext4: fix data corruption caused by overlapping unaligned and aligned IO
  jbd2: fix potential double free
  ext4: zero out the unused memory region in the extent tree block

Pull cifs fixes from Steve French:
 "Minor cleanup and fixes, one for stable, four rdma (smbdirect)
  related. Also adds SEEK_HOLE support"

* tag '5.2-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: add support for SEEK_DATA and SEEK_HOLE
  Fixed https://bugzilla.kernel.org/show_bug.cgi?id=202935 allow write on the same file
  cifs: Allocate memory for all iovs in smb2_ioctl
  cifs: Don't match port on SMBDirect transport
  cifs:smbd Use the correct DMA direction when sending data
  cifs:smbd When reconnecting to server, call smbd_destroy() after all MIDs have been called
  cifs: use the right include for signal_pending()
  smb3: trivial cleanup to smb2ops.c
  cifs: cleanup smb2ops.c and normalize strings
  smb3: display session id in debug data

Pull perf tooling updates from Ingo Molnar:
 "perf.data:

   - Streaming compression of perf ring buffer into
     PERF_RECORD_COMPRESSED user space records, resulting in ~3-5x
     perf.data file size reduction on variety of tested workloads what
     saves storage space on larger server systems where perf.data size
     can easily reach several tens or even hundreds of GiBs, especially
     when profiling with DWARF-based stacks and tracing of context
     switches.

  perf record:

   - Improve -user-regs/intr-regs suggestions to overcome errors

  perf annotate:

   - Remove hist__account_cycles() from callback, speeding up branch
     processing (perf record -b)

  perf stat:

   - Add a 'percore' event qualifier, e.g.: -e
     cpu/event=0,umask=0x3,percore=1/, that sums up the event counts for
     both hardware threads in a core.

     We can already do this with --per-core, but it's often useful to do
     this together with other metrics that are collected per hardware
     thread.

     I.e. now its possible to do this per-event, and have it mixed with
     other events not aggregated by core.

  arm64:

   - Map Brahma-B53 CPUID to cortex-a53 events.

   - Add Cortex-A57 and Cortex-A72 events.

  csky:

   - Add DWARF register mappings for libdw, allowing --call-graph=dwarf
     to work on the C-SKY arch.

  x86:

   - Add support for recording and printing XMM registers, available,
     for instance, on Icelake.

   - Add uncore_upi (Intel's "Ultra Path Interconnect" events) JSON
     support. UPI replaced the Intel QuickPath Interconnect (QPI) in
     Xeon Skylake-SP.

  Intel PT:

   - Fix instructions sampling rate.

   - Timestamp fixes.

   - Improve exported-sql-viewer GUI, allowing, for instance, to
     copy'n'paste the trees, useful for e-mailing"

* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (73 commits)
  perf stat: Support 'percore' event qualifier
  perf stat: Factor out aggregate counts printing
  perf tools: Add a 'percore' event qualifier
  perf docs: Add description for stderr
  perf intel-pt: Fix sample timestamp wrt non-taken branches
  perf intel-pt: Fix improved sample timestamp
  perf intel-pt: Fix instructions sampling rate
  perf regs x86: Add X86 specific arch__intr_reg_mask()
  perf parse-regs: Add generic support for arch__intr/user_reg_mask()
  perf parse-regs: Split parse_regs
  perf vendor events arm64: Add Cortex-A57 and Cortex-A72 events
  perf vendor events arm64: Map Brahma-B53 CPUID to cortex-a53 events
  perf vendor events arm64: Remove [[:xdigit:]] wildcard
  perf jevents: Remove unused variable
  perf test zstd: Fixup verbose mode output
  perf tests: Implement Zstd comp/decomp integration test
  perf inject: Enable COMPRESSED record decompression
  perf report: Implement perf.data record decompression
  perf record: Implement -z,--compression_level[=<n>] option
  perf report: Add stub processing of compressed events for -D
  ...

Pull clocksource updates from Ingo Molnar:
 "Misc clocksource/clockevent driver updates that came in a bit late but
  are ready for v5.2"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  misc: atmel_tclib: Do not probe already used TCBs
  clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static
  clocksource/drivers/tcb_clksrc: Rename the file for consistency
  clocksource/drivers/timer-atmel-pit: Rework Kconfig option
  clocksource/drivers/tcb_clksrc: Move Kconfig option
  ARM: at91: Implement clocksource selection
  clocksource/drivers/tcb_clksrc: Use tcb as sched_clock
  clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib
  ARM: at91: move SoC specific definitions to SoC folder
  clocksource/drivers/timer-milbeaut: Cleanup common register accesses
  clocksource/drivers/timer-milbeaut: Add shutdown function
  clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer
  clocksource/drivers/tegra: Rework for compensation of suspend time
  clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804
  clocksource/drivers/sun4i: Add a compatible for suniv
  dt-bindings: timer: Add Allwinner suniv timer

Pull IRQ chip updates from Ingo Molnar:
 "A late irqchips update:

   - New TI INTR/INTA set of drivers

   - Rewrite of the stm32mp1-exti driver as a platform driver

   - Update the IOMMU MSI mapping API to be RT friendly

   - A number of cleanups and other low impact fixes"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
  iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
  irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
  irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
  irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
  irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
  iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
  genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
  arm64: arch_k3: Enable interrupt controller drivers
  irqchip/ti-sci-inta: Add msi domain support
  soc: ti: Add MSI domain bus support for Interrupt Aggregator
  irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
  dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
  irqchip/ti-sci-intr: Add support for Interrupt Router driver
  dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
  gpio: thunderx: Use the default parent apis for {request,release}_resources
  genirq: Introduce irq_chip_{request,release}_resource_parent() apis
  firmware: ti_sci: Add helper apis to manage resources
  firmware: ti_sci: Add RM mapping table for am654
  firmware: ti_sci: Add support for IRQ management
  firmware: ti_sci: Add support for RM core ops
  ...

Pull EFI fix from Ingo Molnar:
 "Fix an EFI-fb regression that affects certain x86 systems"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  fbdev/efifb: Ignore framebuffer memmap entries that lack any memory types