In a few cases the err-variable is not set to a negative error code if a
function call in typhoon_init_one() fails and thus 0 is returned
instead.
It may be better to set err to the appropriate negative error
code before returning.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188841Reported-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de>
Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

IP_MULTICAST_IF fails if sk_bound_dev_if is already set and the new index
does not match it. e.g.,

    ntpd[15381]: setsockopt IP_MULTICAST_IF 192.168.1.23 fails: Invalid argument

Relax the check in setsockopt to allow setting mc_index to an L3 slave if
sk_bound_dev_if points to an L3 master.

Make a similar change for IPv6. In this case change the device lookup to
take the rcu_read_lock avoiding a refcnt. The rcu lock is also needed for
the lookup of a potential L3 master device.

This really only silences a setsockopt failure since uses of mc_index are
secondary to sk_bound_dev_if if it is set. In both cases, if either index
is an L3 slave or master, lookups are directed to the same FIB table so
relaxing the check at setsockopt time causes no harm.

Patch is based on a suggested change by Darwin for a problem noted in
their code base.
Suggested-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reads from Octeon PCI console are inefficient because before each read
operation, a dynamic mapping to Octeon DRAM is set up.  This patch replaces
the repeated setup of a dynamic mapping with a one-time setup of a static
mapping.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement ndo_get_phys_port_id() by returning the physical port number
of the switch this per-port DSA created network interface corresponds
to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Oftenly, introducing side effects on packet processing on the other half
of the stack by adjusting one of TX/RX via sysctl is not desirable.
There are cases of demand for asymmetric, orthogonal configurability.

This holds true especially for nodes where RPS for RFS usage on top is
configured and therefore use the 'old dev_weight'. This is quite a
common base configuration setup nowadays, even with NICs of superior processing
support (e.g. aRFS).

A good example use case are nodes acting as noSQL data bases with a
large number of tiny requests and rather fewer but large packets as responses.
It's affordable to have large budget and rx dev_weights for the
requests. But as a side effect having this large a number on TX
processed in one run can overwhelm drivers.

This patch therefore introduces an independent configurability via sysctl to
userland.
Signed-off-by: Matthias Tafelmeier <matthias.tafelmeier@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds Energy Efficiency Ethernet to GMAC4.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch refactors sctp_datamsg_from_user() in an attempt to make it
better to read and avoid code duplication for handling the last
fragment.

It also avoids doing division and remaining operations. Even though, it
should still operate similarly as before this patch.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: updates for net-next.

This patch series for net-next contains cleanups, new features and minor
fixes.  The driver specific busy polling code is removed to use busy
polling support in core networking.  Hardware RFS support is enhanced with
added ipv6 flows support and VF support.  A new scheme to allocate TX
rings from the firmware is implemented for newer chips and firmware.  Plus
some misc. cleanups, minor fixes, and to add the maintainer entry.  Please
review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code assumes that we will always have at least 2 rx rings, 1
will be used as an aggregation ring for TPA and jumbo page placements.
However, it is possible, especially on a VF, that there is only 1 rx
ring available.  In this scenario, the current code will fail to initialize.
To handle it, we need to properly set up only 1 ring without aggregation.
Set a new flag BNXT_FLAG_NO_AGG_RINGS for this condition and add logic to
set up the chip to place RX data linearly into a single buffer per packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the added support for the bnxt_re RDMA driver, both drivers can be
allocating completion rings in any order.  The firmware does not know
which completion ring should be receiving async events.  Add an
extra step to tell firmware the completion ring number for receiving
async events after bnxt_en allocates the completion rings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to properly support TX rate limiting in SRIOV VF functions or
NPAR functions, firmware needs better control over tx ring allocations.
The new scheme requires the driver to reserve the number of tx rings
and to query to see if the requested number of tx rings is reserved.
The driver will use the new scheme when the firmware interface spec is
1.6.1 or newer.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accept ipv6 flows in .ndo_rx_flow_steer() and support ETHTOOL_GRXCLSRULE
ipv6 flows.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Assign additional vnics to VFs whenever possible so that NTUPLE can be
supported on the VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existing hardware RFS mode uses one hardware RSS context block
per ring just to calculate the RSS hash.  This is very wasteful and
prevents VF functions from using it.  The new hardware mode shares
the same hardware RSS context for RSS placement and RFS steering.
This allows VFs to enable RFS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add function bnxt_rfs_supported() that determines if the chip supports
RFS.  Refactor the existing function bnxt_rfs_capable() that determines
if run-time conditions support RFS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new vnic RSS capability will enhance NTUPLE support, to be added
in subsequent patches.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call tcp_gro_complete() in the common code path instead of the chip-
specific method.  The newer 5731x method is missing the call.
Signed-off-by: Michael Chan <michael.chan@broadcmo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The advertising field is closely related to the auto_link_speeds field.
The former is the user setting while the latter is the firmware setting.
Both should be u16.  We should use the advertising field in
bnxt_get_link_ksettings because the auto_link_speeds field may not
be updated with the latest from the firmware yet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IRQ is disabled by writing to the completion ring doorbell.  This
should be done before the hardware completion ring is freed for correctness.
The current code disables IRQs after all the completion rings are freed.

Fix it by calling bnxt_disable_int_sync() before freeing the completion
rings.  Rearrange the code to avoid forward declaration.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For better busy polling and GRO support.  Do not re-arm IRQ if
napi_complete_done() returns false.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use native NAPI polling instead.  The next patch will complete the work
by switching to use napi_complete_done()
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename DAUGTHER_ID to DAUGHTER_ID to fix spelling mistake
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

np is already assigned in the variable declaration of ping_v6_sendmsg.
At this point, we have already dereferenced np several times, so the
NULL check is also redundant.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the hardware is synthesized with multiple queues, all queues are
disabled for default. This patch adds the rx queues configuration.
This patch was successfully tested in a Synopsys QoS Reference design.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Different namespace application might require different maximal
number of remembered connection requests.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Different namespace application might require fast recycling
TIME-WAIT sockets independently of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

when some other buffer is immediately copied into allocated region.
Replace calls to kmalloc followed by a memcpy with a direct
call to kmemdup.
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several macros use non-standard styles where format and arguments
are not verified.  Convert these to a more typical fmt, ##__VA_ARGS__
use so format and arguments match as appropriate.

Miscellanea:

o Fix format and argument mismatches
o Realign and reindent misindented block
o Strip newlines from formats and add to macro defines
o Coalesce a few consecutive logging uses to more simple single uses
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Logging macros should allow format and argument validation.
The DB_TX, DB_RX, and DB_GEN macros did not.

Update the macros and uses and add no_printk validation to the
previously compiled away #ifndef DEBUG variants.

Done with coccinelle and some typing.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This pr_debug may help identify why the system is generating some
Aborts. It's not something a sysadmin would be expected to use.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are three functions which would invoke the ipvlan_count_rx. They
are ipvlan_process_multicast, ipvlan_rcv_frame, and ipvlan_nf_input.
The former two functions already use the ipvlan directly before
ipvlan_count_rx, and ipvlan_nf_input gets the ipvlan from
ipvl_addr->master, it is not possible to be NULL too.
So the ipvlan pointer check is unnecessary in ipvlan_count_rx.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are some duplicated codes in ipvlan_add_addr6/4 and
ipvlan_del_addr6/4. Now define two common functions ipvlan_add_addr
and ipvlan_del_addr to decrease the duplicated codes.
It could be helful to maintain the codes.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner says:

====================
SCTP cleanups

Some cleanups/simplifications I've been collecting.
Resending now with net-next open.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no reason to use this cascading. It doesn't add anything.
Let's remove it and simplify.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make it a bit easier to read.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.

    The most important is to not assume the packet is RX just because
    the destination address matches that of the device. Such an
    assumption causes problems when an interface is put into loopback
    mode.

 2) If we retry when creating a new tc entry (because we dropped the
    RTNL mutex in order to load a module, for example) we end up with
    -EAGAIN and then loop trying to replay the request. But we didn't
    reset some state when looping back to the top like this, and if
    another thread meanwhile inserted the same tc entry we were trying
    to, we re-link it creating an enless loop in the tc chain. Fix from
    Daniel Borkmann.

 3) There are two different WRITE bits in the MDIO address register for
    the stmmac chip, depending upon the chip variant. Due to a bug we
    could set them both, fix from Hock Leong Kweh.

 4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: stmmac: fix incorrect bit set in gmac4 mdio addr register
  r8169: add support for RTL8168 series add-on card.
  net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
  openvswitch: upcall: Fix vlan handling.
  ipv4: Namespaceify tcp_tw_reuse knob
  net: korina: Fix NAPI versus resources freeing
  net, sched: fix soft lockup in tc_classify
  net/mlx4_en: Fix user prio field in XDP forward
  tipc: don't send FIN message from connectionless socket
  ipvlan: fix multicast processing
  ipvlan: fix various issues in ipvlan_process_multicast()