And earlier commit removed the error label to two statements that
are now never reachable.  Since this code is now dead code, remove it.

Detected by CoverityScan, CID#1462409 ("Structurally dead code")

Fixes: d5d885fd ("md: introduce new personality funciton start()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shaohua Li <shli@fb.com>

Commit 35bfc521 ("md: allow metadata update while suspending.")
added support for allowing md_check_recovery() to still perform
metadata updates while the array is entering the 'suspended' state.
This is needed to allow the processes of entering the state to
complete.

Unfortunately, the patch doesn't really work.  The test for
"mddev->suspended" at the start of md_check_recovery() means that the
function doesn't try to do anything at all while entering suspend.

This patch moves the code of updating the metadata while suspending to
*before* the test on mddev->suspended.
Reported-by: Jeff Mahoney <jeffm@suse.com>
Fixes: 35bfc521 ("md: allow metadata update while suspending.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>

If we change the number of array's device after device is removed from array,
then add the device back to array, we can see that device is added as active
role instead of spare which we expected.

Please see the below link for details:
https://marc.info/?l=linux-raid&m=153736982015076&w=2

This is caused by that we prefer to use device's previous role which is
recorded by saved_raid_disk, but we should respect the new number of
conf->raid_disks since it could be changed after device is removed.
Reported-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Tested-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>

[Symptom]

Resync thread hang when new added disk faulty during replacing.

[Root Cause]

In raid10_sync_request(), we expect to issue a bio with callback
end_sync_read(), and a bio with callback end_sync_write().

In normal situation, we will add resyncing sectors into
mddev->recovery_active when raid10_sync_request() returned, and sub
resynced sectors from mddev->recovery_active when end_sync_write()
calls end_sync_request().

If new added disk, which are replacing the old disk, is set faulty,
there is a race condition:
    1. In the first rcu protected section, resync thread did not detect
       that mreplace is set faulty and pass the condition.
    2. In the second rcu protected section, mreplace is set faulty.
    3. But, resync thread will prepare the read object first, and then
       check the write condition.
    4. It will find that mreplace is set faulty and do not have to
       prepare write object.
This cause we add resync sectors but never sub it.

[How to Reproduce]

This issue can be easily reproduced by the following steps:
    mdadm -C /dev/md0 --assume-clean -l 10 -n 4 /dev/sd[abcd]
    mdadm /dev/md0 -a /dev/sde
    mdadm /dev/md0 --replace /dev/sdd
    sleep 1
    mdadm /dev/md0 -f /dev/sde

[How to Fix]

This issue can be fixed by using local variables to record the result
of test conditions. Once the conditions are satisfied, we can make sure
that we need to issue a bio for read and a bio for write.

Previous 'commit 24afd80d ("md/raid10: handle recovery of
replacement devices.")' will also check whether bio is NULL, but leave
the comment saying that it is a pointless test. So we remove this dummy
check.
Reported-by: Alex Chen <alexchen@synology.com>
Reviewed-by: Allen Peng <allenpeng@synology.com>
Reviewed-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: Alex Wu <alexwu@synology.com>
Signed-off-by: Shaohua Li <shli@fb.com>

Currently there is an inconsistency for failing the member drives
for arrays with different RAID levels. For RAID456 - there is a possibility
to fail all of the devices. However - for other RAID levels - kernel blocks
removing the member drive, if the operation results in array's FAIL state
(EBUSY is returned). For example - removing last drive from RAID1 is not
possible.
This kind of blocker was never implemented for raid456 and we cannot see
the reason why.

We had tested following patch and did not observe any regression, so do you
have any comments/reasons for current approach, or we can send the proper
patch for this?
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>

Dave writes:
  "drm fixes for 4.19-rc6

   Looks like a pretty normal week for graphics,

   core: syncobj fix, panel link regression revert
   amd: suspend/resume fixes, EDID emulation fix
   mali-dp: NV12 writeback and vblank reset fixes
   etnaviv: DMA setup fix"

* tag 'drm-fixes-2018-09-28' of git://anongit.freedesktop.org/drm/drm:
  drm/amd/display: Fix Edid emulation for linux
  drm/amd/display: Fix Vega10 lightup on S3 resume
  drm/amdgpu: Fix vce work queue was not cancelled when suspend
  Revert "drm/panel: Add device_link from panel device to DRM device"
  drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
  drm/malidp: Fix writeback in NV12
  drm: mali-dp: Call drm_crtc_vblank_reset on device init
  drm/etnaviv: add DMA configuration for etnaviv platform device

Merge tag 'riscv-for-linus-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux

Palmer writes:
  "A Single RISC-V Update for 4.19-rc6

   The Debian guys have been pushing on our port and found some
   unversioned symbols leaking into modules.  This PR contains a single
   fix for that issue."

* tag 'riscv-for-linus-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
  RISC-V: include linux/ftrace.h in asm-prototypes.h

Bjorn writes:
  "PCI fixes:

  - Fix ACPI hotplug issue that causes black screen crash at boot (Mika
    Westerberg)

  - Fix DesignWare "scheduling while atomic" issues (Jisheng Zhang)

  - Add PPC contacts to MAINTAINERS for PCI core error handling (Bjorn
    Helgaas)

  - Sort Mobiveil MAINTAINERS entry (Lorenzo Pieralisi)"

* tag 'pci-v4.19-fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
  PCI: dwc: Fix scheduling while atomic issues
  MAINTAINERS: Move mobiveil PCI driver entry where it belongs
  MAINTAINERS: Update PPC contacts for PCI core error handling

Just a few fixes for 4.19:
- Couple of suspend/resume fixes
- Fix EDID emulation with DC
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927155418.2813-1-alexander.deucher@amd.com

Merge tag 'drm-misc-fixes-2018-09-27-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes

- Revert adding device-link to panels
- Don't leak fences in drm/syncobj
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927152712.GA53076@art_vandelay

Jason writes:
  "Second RDMA rc pull request

   - Fix a long standing race bug when destroying comp_event file descriptors

   - srp, hfi1, bnxt_re: Various driver crashes from missing validation
     and other cases

   - Fixes for regressions in patches merged this window in the gid
     cache, devx, ucma and uapi."

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/core: Set right entry state before releasing reference
  IB/mlx5: Destroy the DEVX object upon error flow
  IB/uverbs: Free uapi on destroy
  RDMA/bnxt_re: Fix system crash during RDMA resource initialization
  IB/hfi1: Fix destroy_qp hang after a link down
  IB/hfi1: Fix context recovery when PBC has an UnsupportedVL
  IB/hfi1: Invalid user input can result in crash
  IB/hfi1: Fix SL array bounds check
  RDMA/uverbs: Fix validity check for modify QP
  IB/srp: Avoid that sg_reset -d ${srp_device} triggers an infinite loop
  ucma: fix a use-after-free in ucma_resolve_ip()
  RDMA/uverbs: Atomically flush and mark closed the comp event queue
  cxgb4: fix abort_req_rss6 struct

Jan writes:
  "an ext2 patch fixing fsync(2) for DAX mounts."

* tag 'for_v4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  ext2, dax: set ext2_dax_aops for dax files

[Why]
EDID emulation didn't work properly for linux, as we stop programming
if nothing is connected physically.

[How]
We get a flag from DRM when we want to do edid emulation. We check if
this flag is true and nothing is connected physically, if so we only
program the front end using VIRTUAL_SIGNAL.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
There have been a few reports of Vega10 display remaining blank
after S3 resume. The regression is caused by workaround for mode
change on Vega10 - skip set_bandwidth if stream count is 0.
As a result we skipped dispclk reset on suspend, thus on resume
we may skip the clock update assuming it hasn't been changed.
On some systems it causes display blank or 'out of range'.

[How]
Revert "drm/amd/display: Fix Vega10 black screen after mode change"
Verified that it hadn't cause mode change regression.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The vce cancel_delayed_work_sync never be called.
driver call the function in error path.

This caused the A+A suspend hang when runtime pm enebled.
As we will visit the smu in the idle queue. this will cause
smu hang because the dgpu has been suspend, and the dgpu also
will be waked up. As the smu has been hang, so the dgpu resume
will failed.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

This reverts commit 0c08754b.

commit 0c08754b
("drm/panel: Add device_link from panel device to DRM device")
creates a circular dependency under these circumstances:

1. The panel depends on dsi-host because it is MIPI-DSI child
   device.
2. dsi-host depends on the drm parent device (connector->dev->dev)
   this should be allowed.
3. drm parent dev (connector->dev->dev) depends on the panel
   after this patch.

This makes the dependency circular and while it appears it
does not affect any in-tree drivers (they do not seem to have
dsi hosts depending on the same parent device) this does not
seem right.

As noted in a response from Andrzej Hajda, the intent is
likely to make the panel dependent on the DRM device
(connector->dev) not its parent. But we have no way of
doing that since the DRM device doesn't contain any
struct device on its own (arguably it should).

Revert this until a proper approach is figured out.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927124130.9102-1-linus.walleij@linaro.org

Fix NV12 writeback and fix vblank reset.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Liviu Dudau <Liviu.Dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180921112354.GR936@e110455-lin.cambridge.arm.com

one fix to get a proper DMA configuration in place for the etnaviv
virtual device. I'm sending this as a fix, as a dma-mapping change at
the ARC architecture side during the 4.19 cycle broke etnaviv on this
platform, which gets remedied with this patch, but it also enables
ARM64.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/ea1f712bf09bf9439c6b092bf2c2bde7bb01cf5e.camel@pengutronix.de

HP 6730b laptop has an ethernet NIC connected to one of the PCIe root
ports.  The root ports themselves are native PCIe hotplug capable.  Now,
during boot after PCI devices are scanned the BIOS triggers ACPI bus check
directly to the NIC:

  ACPI: \_SB_.PCI0.RP06.NIC_: Bus check in hotplug_event()

It is not clear why it is sending bus check but regardless the ACPI hotplug
notify handler calls enable_slot() directly (instead of going through
acpiphp_check_bridge() as there is no bridge), which ends up handling
special case for non-hotplug bridges with native PCIe hotplug.  This
results a crash of some kind but the reporter only sees black screen so it
is hard to figure out the exact spot and what actually happens.  Based on
a few fix proposals it was tracked to crash somewhere inside
pci_assign_unassigned_bridge_resources().

In any case we should not really be in that special branch at all because
the ACPI notify happened to a slot that is not a PCI bridge (it is just a
regular PCI device).

Fix this so that we only go to that special branch if we are calling
enable_slot() for a bridge (e.g., the ACPI notification was for the
bridge).

Link: https://bugzilla.kernel.org/show_bug.cgi?id=201127
Fixes: 84c8b58e ("ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug")
Reported-by: Peter Anemone <peter.anemone@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org	# v4.18+

We attempt to get fences earlier in the hopes that everything will
already have fences and no callbacks will be needed.  If we do succeed
in getting a fence, getting one a second time will result in a duplicate
ref with no unref.  This is causing memory leaks in Vulkan applications
that create a lot of fences; playing for a few hours can, apparently,
bring down the system.

Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107899Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926071703.15257-1-jason.ekstrand@intel.com

Joerg writes:
  "IOMMU Fixes for Linux v4.19-rc5

   Three fixes queued up:

	- Warning fix for Rockchip IOMMU where there were IRQ handlers
	  for offlined hardware.

	- Fix for Intel VT-d because recent changes caused boot failures
	  on some machines because it tried to allocate to much
	  contiguous memory.

	- Fix for AMD IOMMU to handle eMMC devices correctly that appear
	  as ACPI HID devices."

* tag 'iommu-fixes-v4.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Return devid as alias for ACPI HID devices
  iommu/vt-d: Handle memory shortage on pasid table allocation
  iommu/rockchip: Free irqs in shutdown handler

ACPI HID devices do not actually have an alias for
them in the IVRS. But dev_data->alias is still used
for indexing into the IOMMU device table for devices
being handled by the IOMMU. So for ACPI HID devices,
we simply return the corresponding devid as an alias,
as parsed from IVRS table.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Fixes: 2bf9a0a1 ('iommu/amd: Add iommu support for ACPI HID devices')
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Currently add_modify_gid() for IB link layer has followong issue
in cache update path.

When GID update event occurs, core releases reference to the GID
table without updating its state and/or entry pointer.

CPU-0                              CPU-1
------                             -----
ib_cache_update()                    IPoIB ULP
   add_modify_gid()                   [..]
      put_gid_entry()
      refcnt = 0, but
      state = valid,
      entry is valid.
      (work item is not yet executed).
                                   ipoib_create_ah()
                                     rdma_create_ah()
                                        rdma_get_gid_attr() <--
                                   	Tries to acquire gid_attr
                                        which has refcnt = 0.
                                   	This is incorrect.

GID entry state and entry pointer is provides the accurate GID enty
state. Such fields must be updated with rwlock to protect against
readers and, such fields must be in sane state before refcount can drop
to zero. Otherwise above race condition can happen leading to
use-after-free situation.

Following backtrace has been observed when cache update for an IB port
is triggered while IPoIB ULP is creating an AH.

Therefore, when updating GID entry, first mark a valid entry as invalid
through state and set the barrier so that no callers can acquired
the GID entry, followed by release reference to it.

refcount_t: increment on 0; use-after-free.
WARNING: CPU: 4 PID: 29106 at lib/refcount.c:153 refcount_inc_checked+0x30/0x50
Workqueue: ib-comp-unb-wq ib_cq_poll_work [ib_core]
RIP: 0010:refcount_inc_checked+0x30/0x50
RSP: 0018:ffff8802ad36f600 EFLAGS: 00010082
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000002 RSI: 0000000000000008 RDI: ffffffff86710100
RBP: ffff8802d6e60a30 R08: ffffed005d67bf8b R09: ffffed005d67bf8b
R10: 0000000000000001 R11: ffffed005d67bf8a R12: ffff88027620cee8
R13: ffff8802d6e60988 R14: ffff8802d6e60a78 R15: 0000000000000202
FS: 0000000000000000(0000) GS:ffff8802eb200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3ab35e5c88 CR3: 00000002ce84a000 CR4: 00000000000006e0
IPv6: ADDRCONF(NETDEV_CHANGE): ib1: link becomes ready
Call Trace:
rdma_get_gid_attr+0x220/0x310 [ib_core]
? lock_acquire+0x145/0x3a0
rdma_fill_sgid_attr+0x32c/0x470 [ib_core]
rdma_create_ah+0x89/0x160 [ib_core]
? rdma_fill_sgid_attr+0x470/0x470 [ib_core]
? ipoib_create_ah+0x52/0x260 [ib_ipoib]
ipoib_create_ah+0xf5/0x260 [ib_ipoib]
ipoib_mcast_join_complete+0xbbe/0x2540 [ib_ipoib]

Fixes: b150c386 ("IB/core: Introduce GID entry reference counts")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

Upon DEVX object creation the object must be destroyed upon a follows
error flow.

Fixes: 7efce369 ("IB/mlx5: Add obj create and destroy functionality")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

Make sure we free struct uverbs_api once we clean the radix tree. It was
allocated by uverbs_alloc_api().

Fixes: 9ed3e5f4 ("IB/uverbs: Build the specs into a radix tree at runtime")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

Dan writes:
  "libnvdimm/dax for 4.19-rc6

  * (2) fixes for the dax error handling updates that were merged for
  v4.19-rc1. My mails to Al have been bouncing recently, so I do not have
  his ack but the uaccess change is of the trivial / obviously correct
  variety. The address_space_operations fixes a regression.

  * A filesystem-dax fix to correct the zero page lookup to be compatible
   with non-x86 (mips and s390) architectures."

* tag 'libnvdimm-fixes-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: Add missing address_space_operations
  uaccess: Fix is_source param for check_copy_size() in copy_to_iter_mcsafe()
  filesystem-dax: Fix use of zero page

James writes:
  "SCSI fixes on 20180925

   Nine obvious bug fixes mostly in individual drivers.  The target fix
   is of particular importance because it's CVE related."

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: sd: don't crash the host on invalid commands
  scsi: ipr: System hung while dlpar adding primary ipr adapter back
  scsi: target: iscsi: Use bin2hex instead of a re-implementation
  scsi: target: iscsi: Use hex2bin instead of a re-implementation
  scsi: lpfc: Synchronize access to remoteport via rport
  scsi: ufs: Disable blk-mq for now
  scsi: sd: Contribute to randomness when running rotational device
  scsi: ibmvscsis: Ensure partition name is properly NUL terminated
  scsi: ibmvscsis: Fix a stringop-overflow warning

I wrote:
  "USB fixes for 4.19-rc6

   Here are some small USB core and driver fixes for reported issues for
   4.19-rc6.

   The most visible is the oops fix for when the USB core is built into the
   kernel that is present in 4.18.  Turns out not many people actually do
   that so it went unnoticed for a while.  The rest is some tiny typec,
   musb, and other core fixes.

   All have been in linux-next with no reported issues."

* tag 'usb-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: mux: Take care of driver module reference counting
  usb: core: safely deal with the dynamic quirk lists
  usb: roles: Take care of driver module reference counting
  USB: handle NULL config in usb_find_alt_setting()
  USB: fix error handling in usb_driver_claim_interface()
  USB: remove LPM management from usb_driver_claim_interface()
  USB: usbdevfs: restore warning for nonsensical flags
  USB: usbdevfs: sanitize flags more
  Revert "usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()"
  usb: musb: dsps: do not disable CPPI41 irq in driver teardown

I wrote:
  "TTY/Serial driver fixes for 4.19-rc6

   Here are a number of small tty and serial driver fixes for reported
   issues for 4.19-rc6.

   One should hopefully resolve a much-reported issue that syzbot has found
   in the tty layer.  Although there are still more issues there, getting
   this fixed is nice to see finally happen.

   All of these have been in linux-next for a while with no reported
   issues."

* tag 'tty-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: imx: restore handshaking irq for imx1
  tty: vt_ioctl: fix potential Spectre v1
  tty: Drop tty->count on tty_reopen() failure
  serial: cpm_uart: return immediately from console poll
  tty: serial: lpuart: avoid leaking struct tty_struct
  serial: mvebu-uart: Fix reporting of effective CSIZE to userspace

Greg (well I), wrote:
  "Char/Misc driver fixes for 4.19-rc6

   Here are some soundwire and intel_th (tracing) driver fixes for some
   reported issues.

   All of these have been in linux-next for a week with no reported issues."

* tag 'char-misc-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  intel_th: pci: Add Ice Lake PCH support
  intel_th: Fix resource handling for ACPI glue layer
  intel_th: Fix device removal logic
  soundwire: Fix acquiring bus lock twice during master release
  soundwire: Fix incorrect exit after configuring stream
  soundwire: Fix duplicate stream state assignment

Pasid table memory allocation could return failure due to memory
shortage. Limit the pasid table size to 1MiB because current 8MiB
contiguous physical memory allocation can be hard to come by. W/o
a PASID table, the device could continue to work with only shared
virtual memory impacted. So, let's go ahead with context mapping
even the memory allocation for pasid table failed.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107783
Fixes: cc580e41 ("iommu/vt-d: Per PCI device pasid table interfaces")

Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-and-tested-by: Pelton Kyle D <kyle.d.pelton@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This changes UAPI, breaking iwd and libell:

  ell/key.c: In function 'kernel_dh_compute':
  ell/key.c:205:38: error: 'struct keyctl_dh_params' has no member named 'private'; did you mean 'dh_private'?
    struct keyctl_dh_params params = { .private = private,
                                        ^~~~~~~
                                        dh_private

This reverts commit 8a2336e5.

Fixes: 8a2336e5 ("uapi/linux/keyctl.h: don't use C++ reserved keyword as a struct member name")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Randy Dunlap <rdunlap@infradead.org>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Stephan Mueller <smueller@chronox.de>
cc: James Morris <jmorris@namei.org>
cc: "Serge E. Hallyn" <serge@hallyn.com>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: Linus Torvalds <torvalds@linux-foundation.org>
cc: <stable@vger.kernel.org>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Dave writes:
  "Networking fixes:

  1) Fix multiqueue handling of coalesce timer in stmmac, from Jose
     Abreu.

   2) Fix memory corruption in NFC, from Suren Baghdasaryan.

   3) Don't write reserved bits in ravb driver, from Kazuya Mizuguchi.

   4) SMC bug fixes from Karsten Graul, YueHaibing, and Ursula Braun.

   5) Fix TX done race in mvpp2, from Antoine Tenart.

   6) ipv6 metrics leak, from Wei Wang.

   7) Adjust firmware version requirements in mlxsw, from Petr Machata.

   8) Fix autonegotiation on resume in r8169, from Heiner Kallweit.

   9) Fixed missing entries when dumping /proc/net/if_inet6, from Jeff
      Barnhill.

   10) Fix double free in devlink, from Dan Carpenter.

   11) Fix ethtool regression from UFO feature removal, from Maciej
       Żenczykowski.

   12) Fix drivers that have a ndo_poll_controller() that captures the
       cpu entirely on loaded hosts by trying to drain all rx and tx
       queues, from Eric Dumazet.

   13) Fix memory corruption with jumbo frames in aquantia driver, from
       Friedemann Gerold."

* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (79 commits)
  net: mvneta: fix the remaining Rx descriptor unmapping issues
  ip_tunnel: be careful when accessing the inner header
  mpls: allow routes on ip6gre devices
  net: aquantia: memory corruption on jumbo frames
  tun: remove ndo_poll_controller
  nfp: remove ndo_poll_controller
  bnxt: remove ndo_poll_controller
  bnx2x: remove ndo_poll_controller
  mlx5: remove ndo_poll_controller
  mlx4: remove ndo_poll_controller
  i40evf: remove ndo_poll_controller
  ice: remove ndo_poll_controller
  igb: remove ndo_poll_controller
  ixgb: remove ndo_poll_controller
  fm10k: remove ndo_poll_controller
  ixgbevf: remove ndo_poll_controller
  ixgbe: remove ndo_poll_controller
  bonding: use netpoll_poll_dev() helper
  netpoll: make ndo_poll_controller() optional
  rds: Fix build regression.
  ...

In the iommu's shutdown handler we disable runtime-pm which could
result in the irq-handler running unclocked and since commit
    3fc7c5c0 ("iommu/rockchip: Handle errors returned from PM framework")
we warn about that fact.

This can cause warnings on shutdown on some Rockchip machines, so
free the irqs in the shutdown handler before we disable runtime-pm.
Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Fixes: 3fc7c5c0 ("iommu/rockchip: Handle errors returned from PM framework")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Building a riscv kernel with CONFIG_FUNCTION_TRACER and
CONFIG_MODVERSIONS enabled results in these two warnings:

  MODPOST vmlinux.o
WARNING: EXPORT symbol "return_to_handler" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "_mcount" [vmlinux] version generation failed, symbol will not be versioned.

When exporting symbols from an assembly file, the MODVERSIONS code
requires their prototypes to be defined in asm-prototypes.h (see
scripts/Makefile.build). Since both of these symbols have prototypes
defined in linux/ftrace.h, include this header from RISC-V's
asm-prototypes.h.
Reported-by: Karsten Merker <merker@debian.org>
Signed-off-by: James Cowgill <jcowgill@debian.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>

With CONFIG_DMA_API_DEBUG enabled we get DMA unmapping warning in
various places of the mvneta driver, for example when putting down an
interface while traffic is passing through.

The issue is when using s/w buffer management, the Rx buffers are mapped
using dma_map_page but unmapped with dma_unmap_single. This patch fixes
this by using the right unmapping function.

Fixes: 562e2f46 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cong noted that we need the same checks introduced by commit 76c0ddd8
("ip6_tunnel: be careful when accessing the inner header")
even for ipv4 tunnels.

Fixes: c5441932 ("GRE: Refactor GRE tunneling code.")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Summary:

This appears to be necessary and sufficient change to enable `MPLS` on
`ip6gre` tunnels (RFC4023).

This diff allows IP6GRE devices to be recognized by MPLS kernel module
and hence user can configure interface to accept packets with mpls
headers as well setup mpls routes on them.

Test Plan:

Test plan consists of multiple containers connected via GRE-V6 tunnel.
Then carrying out testing steps as below.

- Carry out necessary sysctl settings on all containers

```
sysctl -w net.mpls.platform_labels=65536
sysctl -w net.mpls.ip_ttl_propagate=1
sysctl -w net.mpls.conf.lo.input=1
```

- Establish IP6GRE tunnels

```
ip -6 tunnel add name if_1_2_1 mode ip6gre \
  local 2401:db00:21:6048:feed:0::1 \
  remote 2401:db00:21:6048:feed:0::2 key 1
ip link set dev if_1_2_1 up
sysctl -w net.mpls.conf.if_1_2_1.input=1
ip -4 addr add 169.254.0.2/31 dev if_1_2_1 scope link

ip -6 tunnel add name if_1_3_1 mode ip6gre \
  local 2401:db00:21:6048:feed:0::1 \
  remote 2401:db00:21:6048:feed:0::3 key 1
ip link set dev if_1_3_1 up
sysctl -w net.mpls.conf.if_1_3_1.input=1
ip -4 addr add 169.254.0.4/31 dev if_1_3_1 scope link
```

- Install MPLS encap rules on node-1 towards node-2

```
ip route add 192.168.0.11/32 nexthop encap mpls 32/64 \
  via inet 169.254.0.3 dev if_1_2_1
```

- Install MPLS forwarding rules on node-2 and node-3
```
// node2
ip -f mpls route add 32 via inet 169.254.0.7 dev if_2_4_1

// node3
ip -f mpls route add 64 via inet 169.254.0.12 dev if_4_3_1
```

- Ping 192.168.0.11 (node4) from 192.168.0.1 (node1) (where routing
  towards 192.168.0.1 is via IP route directly towards node1 from node4)
```
ping 192.168.0.11
```

- tcpdump on interface to capture ping packets wrapped within MPLS
  header which inturn wrapped within IP6GRE header

```
16:43:41.121073 IP6
  2401:db00:21:6048:feed::1 > 2401:db00:21:6048:feed::2:
  DSTOPT GREv0, key=0x1, length 100:
  MPLS (label 32, exp 0, ttl 255) (label 64, exp 0, [S], ttl 255)
  IP 192.168.0.1 > 192.168.0.11:
  ICMP echo request, id 1208, seq 45, length 64

0x0000:  6000 2cdb 006c 3c3f 2401 db00 0021 6048  `.,..l<?$....!`H
0x0010:  feed 0000 0000 0001 2401 db00 0021 6048  ........$....!`H
0x0020:  feed 0000 0000 0002 2f00 0401 0401 0100  ......../.......
0x0030:  2000 8847 0000 0001 0002 00ff 0004 01ff  ...G............
0x0040:  4500 0054 3280 4000 ff01 c7cb c0a8 0001  E..T2.@.........
0x0050:  c0a8 000b 0800 a8d7 04b8 002d 2d3c a05b  ...........--<.[
0x0060:  0000 0000 bcd8 0100 0000 0000 1011 1213  ................
0x0070:  1415 1617 1819 1a1b 1c1d 1e1f 2021 2223  .............!"#
0x0080:  2425 2627 2829 2a2b 2c2d 2e2f 3031 3233  $%&'()*+,-./0123
0x0090:  3435 3637                                4567
```
Signed-off-by: Saif Hasan <has@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-09-24

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Several fixes for BPF sockmap to only allow sockets being attached in
   ESTABLISHED state, from John.

2) Fix up the license to LGPL/BSD for the libc compat header which contains
   fallback helpers that libbpf and bpftool is using, from Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_re_ib_reg acquires and releases the rtnl lock whenever it accesses
the L2 driver.

The following sequence can trigger a crash

Acquires the rtnl_lock ->
	Registers roce driver callback with L2 driver ->
		release the rtnl lock
bnxt_re acquires the rtnl_lock ->
	Request for MSIx vectors ->
		release the rtnl_lock

Issue happens when bnxt_re proceeds with remaining part of initialization
and L2 driver invokes bnxt_ulp_irq_stop as a part of bnxt_open_nic.

The crash is in bnxt_qplib_nq_stop_irq as the NQ structures are
not initialized yet,

<snip>
[ 3551.726647] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 3551.726656] IP: [<ffffffffc0840ee9>] bnxt_qplib_nq_stop_irq+0x59/0xb0 [bnxt_re]
[ 3551.726674] PGD 0
[ 3551.726679] Oops: 0002 1 SMP
...
[ 3551.726822] Hardware name: Dell Inc. PowerEdge R720/08RW36, BIOS 2.4.3 07/09/2014
[ 3551.726826] task: ffff97e30eec5ee0 ti: ffff97e3173bc000 task.ti: ffff97e3173bc000
[ 3551.726829] RIP: 0010:[<ffffffffc0840ee9>] [<ffffffffc0840ee9>]
bnxt_qplib_nq_stop_irq+0x59/0xb0 [bnxt_re]
...
[ 3551.726872] Call Trace:
[ 3551.726886] [<ffffffffc082cb9e>] bnxt_re_stop_irq+0x4e/0x70 [bnxt_re]
[ 3551.726899] [<ffffffffc07d6a53>] bnxt_ulp_irq_stop+0x43/0x70 [bnxt_en]
[ 3551.726908] [<ffffffffc07c82f4>] bnxt_reserve_rings+0x174/0x1e0 [bnxt_en]
[ 3551.726917] [<ffffffffc07cafd8>] __bnxt_open_nic+0x368/0x9a0 [bnxt_en]
[ 3551.726925] [<ffffffffc07cb62b>] bnxt_open_nic+0x1b/0x50 [bnxt_en]
[ 3551.726934] [<ffffffffc07cc62f>] bnxt_setup_mq_tc+0x11f/0x260 [bnxt_en]
[ 3551.726943] [<ffffffffc07d5f58>] bnxt_dcbnl_ieee_setets+0xb8/0x1f0 [bnxt_en]
[ 3551.726954] [<ffffffff890f983a>] dcbnl_ieee_set+0x9a/0x250
[ 3551.726966] [<ffffffff88fd6d21>] ? __alloc_skb+0xa1/0x2d0
[ 3551.726972] [<ffffffff890f72fa>] dcb_doit+0x13a/0x210
[ 3551.726981] [<ffffffff89003ff7>] rtnetlink_rcv_msg+0xa7/0x260
[ 3551.726989] [<ffffffff88ffdb00>] ? rtnl_unicast+0x20/0x30
[ 3551.726996] [<ffffffff88bf9dc8>] ? __kmalloc_node_track_caller+0x58/0x290
[ 3551.727002] [<ffffffff890f7326>] ? dcb_doit+0x166/0x210
[ 3551.727007] [<ffffffff88fd6d0d>] ? __alloc_skb+0x8d/0x2d0
[ 3551.727012] [<ffffffff89003f50>] ? rtnl_newlink+0x880/0x880
...
[ 3551.727104] [<ffffffff8911f7d5>] system_call_fastpath+0x1c/0x21
...
[ 3551.727164] RIP [<ffffffffc0840ee9>] bnxt_qplib_nq_stop_irq+0x59/0xb0 [bnxt_re]
[ 3551.727175] RSP <ffff97e3173bf788>
[ 3551.727177] CR2: 0000000000000000

Avoid this inconsistent state and  system crash by acquiring
the rtnl lock for the entire duration of device initialization.
Re-factor the code to remove the rtnl lock from the individual function
and acquire and release it from the caller.

Fixes: 1ac5a404 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Fixes: 6e04b103 ("RDMA/bnxt_re: Fix broken RoCE driver due to recent L2 driver changes")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>