bnx2x driver already handles TSO for GRE, current code
is the same for IPIP.

Performance results : (Note we are now limited by receiver,
as it does not support GRO for IPIP yet)

Before patch :

lpq83:~# ./netperf -H 7.7.9.84 -Cc
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.9.84 () port 0 AF_INET
Recv   Send    Send                          Utilization       Service Demand
Socket Socket  Message  Elapsed              Send     Recv     Send    Recv
Size   Size    Size     Time     Throughput  local    remote   local   remote
bytes  bytes   bytes    secs.    10^6bits/s  % S      % S      us/KB   us/KB

 87380  16384  16384    10.00      7710.19   4.52     6.62     1.152   1.687

After patch :

lpq83:~# ./netperf -H 7.7.9.84 -Cc
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.9.84 () port 0 AF_INET
Recv   Send    Send                          Utilization       Service Demand
Socket Socket  Message  Elapsed              Send     Recv     Send    Recv
Size   Size    Size     Time     Throughput  local    remote   local   remote
bytes  bytes   bytes    secs.    10^6bits/s  % S      % S      us/KB   us/KB

 87380  16384  16384    10.00      8532.40   2.55     7.73     0.588   1.781
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now inet_gso_segment() is stackable, its relatively easy to
implement GSO/TSO support for IPIP

Performance results, when segmentation is done after tunnel
device (as no NIC is yet enabled for TSO IPIP support) :

Before patch :

lpq83:~# ./netperf -H 7.7.9.84 -Cc
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.9.84 () port 0 AF_INET
Recv   Send    Send                          Utilization       Service Demand
Socket Socket  Message  Elapsed              Send     Recv     Send    Recv
Size   Size    Size     Time     Throughput  local    remote   local   remote
bytes  bytes   bytes    secs.    10^6bits/s  % S      % S      us/KB   us/KB

 87380  16384  16384    10.00      3357.88   5.09     3.70     2.983   2.167

After patch :

lpq83:~# ./netperf -H 7.7.9.84 -Cc
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.9.84 () port 0 AF_INET
Recv   Send    Send                          Utilization       Service Demand
Socket Socket  Message  Elapsed              Send     Recv     Send    Recv
Size   Size    Size     Time     Throughput  local    remote   local   remote
bytes  bytes   bytes    secs.    10^6bits/s  % S      % S      us/KB   us/KB

 87380  16384  16384    10.00      7710.19   4.52     6.62     1.152   1.687
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to support GSO on IPIP, we need to make
inet_gso_segment() stackable.

It should not assume network header starts right after mac
header.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes gre_handle_offloads() more generic
and rename it to iptunnel_handle_offloads()

This will be used to add GSO/TSO support to IPIP tunnels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While implementing GSO/TSO support for IPIP, I found skb_segment()
was assuming network header was immediately following mac header.

Its not really true in the case inet_gso_segment() is stacked :
By the time tcp_gso_segment() is called, network header points
to the inner IP header.

Let's instead assume nothing and pick the current offsets found in
original skb, we have skb_headers_offset_update() helper for that.

Also move the csum_start update inside skb_headers_offset_update()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6_gso_send_check() and ipv6_gso_segment() are called by
skb_mac_gso_segment() under rcu lock, no need to use
rcu_read_lock() / rcu_read_unlock()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we log a message whenever pcie_enable_error_reporting fails.
The message clutters up logs, especially when we don't support it for VFs.
Instead enable this only for PFs and log a message when the call succeeds.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are a mix of function prototypes with and without extern
in the kernel sources.  Standardize on not using extern for
function prototypes.

Function prototypes don't need to be written with extern.
extern is assumed by the compiler.  Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are a mix of function prototypes with and without extern
in the kernel sources.  Standardize on not using extern for
function prototypes.

Function prototypes don't need to be written with extern.
extern is assumed by the compiler.  Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are a mix of function prototypes with and without extern
in the kernel sources.  Standardize on not using extern for
function prototypes.

Function prototypes don't need to be written with extern.
extern is assumed by the compiler.  Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are a mix of function prototypes with and without extern
in the kernel sources.  Standardize on not using extern for
function prototypes.

Function prototypes don't need to be written with extern.
extern is assumed by the compiler.  Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet_gso_segment() and inet_gso_send_check() are called by
skb_mac_gso_segment() under rcu lock, no need to use
rcu_read_lock() / rcu_read_unlock()

Avoid calling ip_hdr() twice per function.

We can use ip_send_check() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It can be called from the module init function, so it cannot
be in the exit section.
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
bonding: introduce bonding options Netlink support

This patchset basically allows "mode" and "active_slave" bonding options
to be propagated and set up via standart RT Netlink interface.

In future other options can be easily added as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

no longer needed since bond_option_active_slave_set() can be used
instead.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do a bit of refactoring on the way.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Randy found that if network namespace not enabled then
nd_net does not exist and would cause compilation failure.

This is handled correctly by using the dev_net() macro.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the specialized code in __tcp_retransmit_skb() that tries to trim
any ACKed payload preceding a FIN before we retransmit (this was added
in 1999 in v2.2.3pre3). This trimming code was made unreachable by the
more general code added above it that uses tcp_trim_head() to trim any
ACKed payload, with or without a FIN (this was added in "[NET]: Add
segmentation offload support to TCP." in 2002 circa v2.5.33).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under certain low traffic conditions, the single core
devices with multiple Rx/Tx queues (MQ mode) may reach
soft lockup due to gfar_poll not returning in proper time.
The following exception was obtained using iperf on a 100Mbit
half-duplex link, for a p1010 single core device:

BUG: soft lockup - CPU#0 stuck for 23s! [iperf:2847]
Modules linked in:
CPU: 0 PID: 2847 Comm: iperf Not tainted 3.12.0-rc3 #16
task: e8bf8000 ti: eeb16000 task.ti: ee646000
NIP: c0255b6c LR: c0367ae8 CTR: c0461c18
REGS: eeb17e70 TRAP: 0901   Not tainted  (3.12.0-rc3)
MSR: 00029000 <CE,EE,ME>  CR: 44228428  XER: 20000000

GPR00: c0367ad4 eeb17f20 e8bf8000 ee01f4b4 00000008 ffffffff ffffffff
00000000
GPR08: 000000c0 00000008 000000ff ffffffc0 000193fe
NIP [c0255b6c] find_next_bit+0xb8/0xc4
LR [c0367ae8] gfar_poll+0xc8/0x1d8
Call Trace:
[eeb17f20] [c0367ad4] gfar_poll+0xb4/0x1d8 (unreliable)
[eeb17f70] [c0422100] net_rx_action+0xa4/0x158
[eeb17fa0] [c003ec6c] __do_softirq+0xcc/0x17c
[eeb17ff0] [c000c28c] call_do_softirq+0x24/0x3c
[ee647cc0] [c0004660] do_softirq+0x6c/0x94
[ee647ce0] [c003eb9c] local_bh_enable+0x9c/0xa0
[ee647cf0] [c0454fe8] tcp_prequeue_process+0xa4/0xdc
[ee647d10] [c0457e44] tcp_recvmsg+0x498/0x96c
[ee647d80] [c047b630] inet_recvmsg+0x40/0x64
[ee647da0] [c040ca8c] sock_recvmsg+0x90/0xc0
[ee647e30] [c040edb8] SyS_recvfrom+0x98/0xfc

To prevent this, the outer while() loop has been removed
allowing gfar_poll() to return faster even if there's
still budget left.  Also, there's no need to recompute
the budget per Rx queue anymore.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rtmsg_fib function doesn't modify this argument so mark
it const.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current test works fine in practice.  The "amount" variable is
actually used as a boolean so negative values or any non-zero values
count as "true".  However since we don't allow numbers greater than one,
let's not allow negative numbers either.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib_table_lookup has included the rcu lock protection.
Signed-off-by: baker.zhang <baker.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
1) Don't use a wildcard SA if a more precise one is in acquire state,
   from Fan Du.

2) Simplify the SA lookup when using wildcard source. We need to check
   only the destination in this case, from Fan Du.

3) Add a receive path hook for IPsec virtual tunnel interfaces
   to xfrm6_mode_tunnel.

4) Add support for IPsec virtual tunnel interfaces to ipv6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Himanshu Madhani says:

====================
qlcnic: ethtool enhancements and code cleanup.

This patch series contains

o updates to ethtool for pause settings and enhance
  register dump to display mask and ring indices.
o cleanup in DCB code and remove redundant eSwitch enablement command.
o fixed firmware dump collection logic to skip unknown entries.

Changes from v3 -> v4
o Dropped patch for Tx queue validation to be submitted in net.

Changes from v2 -> v3

o Updated patch to print informational messages as per Joe Perches's comment.

Changes from v1 -> v2

o Dropped patch to register device if adapter is in FAILED state for more rework.
o Updated patch to display ring indices via ethtool per Ben Hutchings's comment.
o Update patch for DCB cleanup per Stephen Hemminger's comment.

Please apply to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Driver aborts the minidump collection operation when it finds
  an unknown entry opcode. This patch skips unknown entry type
  and resumes the minidump collection operation.
o Removed a comparision of collected dump size with expected dump size.
  Size may differ when driver decides to skip an entry.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Move dcb specific function definitions to dcb files.
o Move dcb specific variables to qlcnic_dcb structure.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When more than one NIC physical functions are enabled on a port,
eSwitch on that port gets enabled automatically. Driver
need not explicitly enable the eSwitch.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update ethtool standard pause parameter settings and display
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Allow collecting the firmware dump of halted firmware when auto
  recovery is disabled.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Updated ethtool -d <ethX> option to display ring indices for Transmit(Tx),
  Receive(Rx), and Status(St) rings.
o Updated ethtool -d <ethX> option to display ring interrupt mask for Transmit(Tx),
  and Status(St) rings.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename tcp_tso_segment() to tcp_gso_segment(), to better reflect
what is going on, and ease grep games.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jon Maloy says:

====================
Some small and relatively straightforward patches. With exception of
the two first ones they are all unrelated and address minor issues.

v2: update of v1 (http://patchwork.ozlabs.org/patch/277404/)

-added commit to use memcpy_fromiovec on user data as per v1 feedback
-updated sparse fix commit to drop chunks covered by above commit
-added new commit that greatly simplifies the link lookup routine
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When checking statistics or changing parameters on a link, the
link_find_link function is used to locate the link with a given
name. The complex method of deconstructing the name into local
and remote address/interface is error prone and may fail if the
interface names contains special characters. We change the lookup
method to iterate over the list of nodes and compare the link
names.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>