- 14 Feb, 2017 30 commits
-
-
Sébastien Szymanski authored
commit 7f59b319 upstream. GPIO4_11 is on pin 152(MX6DL_PAD_KEY_ROW2) and not on pin 151(MX6DL_PAD_KEY_ROW1). I found the error while booting a mainline kernel on APF6S SoM and noticed the following message: [ 2.609337] imx6dl-pinctrl 20e0000.iomuxc: pin MX6DL_PAD_KEY_ROW1 already requested by 20a8000.gpio:105; cannot claim for 20a8000.gpio:107 [ 2.621884] imx6dl-pinctrl 20e0000.iomuxc: pin-151 (20a8000.gpio:107) status -22 [ 2.629303] spi_imx 2008000.ecspi: Can't get CS GPIO 107 With this patch, the message is gone and spi_imx driver probes correctly. Fixes: bb728d66 ("ARM: dts: add gpio-ranges property to iMX GPIO controllers") Signed-off-by:
Sébastien Szymanski <sebastien.szymanski@armadeus.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nicholas Bellinger authored
commit 9b2792c3 upstream. This patch addresses a long standing bug where the commit phase of COMPARE_AND_WRITE would result in a se_cmd->cmd_kref reference leak if se_cmd->scsi_status returned non SAM_STAT_GOOD. This would manifest first as a lost SCSI response, and eventual hung task during fabric driver logout or re-login, as existing shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref to reach zero. To address this bug, compare_and_write_post() has been changed to drop the incorrect !cmd->scsi_status conditional that was preventing *post_ret = 1 for being set during non SAM_STAT_GOOD status. This patch has been tested with SAM_STAT_CHECK_CONDITION status from normal target_complete_cmd() callback path, as well as the incoming __target_execute_cmd() submission failure path when se_cmd->execute_cmd() returns non zero status. Reported-by:
Donald White <dew@datera.io> Cc: Donald White <dew@datera.io> Tested-by:
Gary Guo <ghg@datera.io> Cc: Gary Guo <ghg@datera.io> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 01d4d673 upstream. This patch addresses a long-standing bug with multi-session (eg: iscsi-target + iser-target) se_node_acl dynamic free withini transport_deregister_session(). This bug is caused when a storage endpoint is configured with demo-mode (generate_node_acls = 1 + cache_dynamic_acls = 1) initiators, and initiator login creates a new dynamic node acl and attaches two sessions to it. After that, demo-mode for the storage instance is disabled via configfs (generate_node_acls = 0 + cache_dynamic_acls = 0) and the existing dynamic acl is never converted to an explicit ACL. The end result is dynamic acl resources are released twice when the sessions are shutdown in transport_deregister_session(). If the storage instance is not changed to disable demo-mode, or the dynamic acl is converted to an explict ACL, or there is only a single session associated with the dynamic ACL, the bug is not triggered. To address this big, move the release of dynamic se_node_acl memory into target_complete_nacl() so it's only freed once when se_node_acl->acl_kref reaches zero. (Drop unnecessary list_del_init usage - HCH) Reported-by:
Rob Millner <rlm@daterainc.com> Tested-by:
-
Nicholas Bellinger authored
commit c54eeffb upstream. This patch fixes a bug where incoming task management requests can be explicitly aborted during an active LUN_RESET, but who's struct work_struct are canceled in-flight before execution. This occurs when core_tmr_drain_tmr_list() invokes cancel_work_sync() for the incoming se_tmr_req->task_cmd->work, resulting in cmd->work for target_tmr_work() never getting invoked and the aborted TMR waiting indefinately within transport_wait_for_tasks(). To address this case, perform a CMD_T_ABORTED check early in transport_generic_handle_tmr(), and invoke the normal path via transport_cmd_check_stop_to_fabric() to complete any TMR kthreads blocked waiting for CMD_T_STOP in transport_wait_for_tasks(). Also, move the TRANSPORT_ISTATE_PROCESSING assignment earlier into transport_generic_handle_tmr() so the existing check in core_tmr_drain_tmr_list() avoids attempting abort the incoming se_tmr_req->task_cmd->work if it has already been queued into se_device->tmr_wq. Reported-by:
-
Nicholas Bellinger authored
commit 0583c261 upstream. This patch adds the missing target_complete_cmd() SCSI status parameter change in target_xcopy_do_work(), that was originally missing in commit 926317de. It correctly propigates up the correct SCSI status during EXTENDED_COPY exception cases, instead of always using the hardcoded SAM_STAT_CHECK_CONDITION from original code. This is required for ESX host environments that expect to hit SAM_STAT_RESERVATION_CONFLICT for certain scenarios, and SAM_STAT_CHECK_CONDITION results in non-retriable status for these cases. Reported-by:
Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by:
-
Nicholas Bellinger authored
commit 391e2a6d upstream. After the v4.2+ RCU conversion to se_node_acl->lun_entry_hlist, a BUG_ON() was added in core_enable_device_list_for_node() to detect when the located orig->se_lun_acl contains an existing se_lun_acl pointer reference. However, this scenario can happen when a dynamically generated NodeACL is being converted to an explicit NodeACL, when the explicit NodeACL contains a different LUN mapping than the default provided by the WWN endpoint. So instead of triggering BUG_ON(), go ahead and fail instead following the original pre RCU conversion logic. Reported-by:
Benjamin ESTRABAUD <ben.estrabaud@mpstor.com> Cc: Benjamin ESTRABAUD <ben.estrabaud@mpstor.com> Reviewed-by:
-
Maarten Lankhorst authored
commit 92c715fc upstream. drm_atomic_helper_page_flip and drm_atomic_ioctl set their own events in crtc_state->event. But when it's set the event is freed in 2 places. Solve this by only freeing the event in the atomic ioctl when it allocated its own event. This has been broken twice. The first time when the code was introduced, but only in the corner case when an event is allocated, but more crtc's were included by atomic check and then failing. This can mostly happen when you do an atomic modeset in i915 and the display clock is changed, which forces all crtc's to be included to the state. This has been broken worse by adding in-fences support, which caused the double free to be done unconditionally. [IGT] kms_rotation_crc: starting subtest primary-rotation-180 ============================================================================= BUG kmalloc-128 (Tainted: G U ): Object already free ----------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: Allocated in drm_atomic_helper_setup_commit+0x285/0x2f0 [drm_kms_helper] age=0 cpu=3 pid=1529 ___slab_alloc+0x308/0x3b0 __slab_alloc+0xd/0x20 kmem_cache_alloc_trace+0x92/0x1c0 drm_atomic_helper_setup_commit+0x285/0x2f0 [drm_kms_helper] intel_atomic_commit+0x35/0x4f0 [i915] drm_atomic_commit+0x46/0x50 [drm] drm_mode_atomic_ioctl+0x7d4/0xab0 [drm] drm_ioctl+0x2b3/0x490 [drm] do_vfs_ioctl+0x69c/0x700 SyS_ioctl+0x4e/0x80 entry_SYSCALL_64_fastpath+0x13/0x94 INFO: Freed in drm_event_cancel_free+0xa3/0xb0 [drm] age=0 cpu=3 pid=1529 __slab_free+0x48/0x2e0 kfree+0x159/0x1a0 drm_event_cancel_free+0xa3/0xb0 [drm] drm_mode_atomic_ioctl+0x86d/0xab0 [drm] drm_ioctl+0x2b3/0x490 [drm] do_vfs_ioctl+0x69c/0x700 SyS_ioctl+0x4e/0x80 entry_SYSCALL_64_fastpath+0x13/0x94 INFO: Slab 0xffffde1f0997b080 objects=17 used=2 fp=0xffff92fb65ec2578 flags=0x200000000008101 INFO: Object 0xffff92fb65ec2578 @offset=1400 fp=0xffff92fb65ec2ae8 Redzone ffff92fb65ec2570: bb bb bb bb bb bb bb bb ........ Object ffff92fb65ec2578: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ffff92fb65ec2588: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ffff92fb65ec2598: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ffff92fb65ec25a8: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ffff92fb65ec25b8: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ffff92fb65ec25c8: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ffff92fb65ec25d8: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ffff92fb65ec25e8: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 kkkkkkkkkkkkkkk. Redzone ffff92fb65ec25f8: bb bb bb bb bb bb bb bb ........ Padding ffff92fb65ec2738: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ CPU: 3 PID: 180 Comm: kworker/3:2 Tainted: G BU 4.10.0-rc6-patser+ #5039 Hardware name: /NUC5PPYB, BIOS PYBSWCEL.86A.0031.2015.0601.1712 06/01/2015 Workqueue: events intel_atomic_helper_free_state [i915] Call Trace: dump_stack+0x4d/0x6d print_trailer+0x20c/0x220 free_debug_processing+0x1c6/0x330 ? drm_atomic_state_default_clear+0xf7/0x1c0 [drm] __slab_free+0x48/0x2e0 ? drm_atomic_state_default_clear+0xf7/0x1c0 [drm] kfree+0x159/0x1a0 drm_atomic_state_default_clear+0xf7/0x1c0 [drm] ? drm_atomic_state_clear+0x30/0x30 [drm] intel_atomic_state_clear+0xd/0x20 [i915] drm_atomic_state_clear+0x1a/0x30 [drm] __drm_atomic_state_free+0x13/0x60 [drm] intel_atomic_helper_free_state+0x5d/0x70 [i915] process_one_work+0x260/0x4a0 worker_thread+0x2d1/0x4f0 kthread+0x127/0x130 ? process_one_work+0x4a0/0x4a0 ? kthread_stop+0x120/0x120 ret_from_fork+0x29/0x40 FIX kmalloc-128: Object at 0xffff92fb65ec2578 not freed Fixes: 3b24f7d6 ("drm/atomic: Add struct drm_crtc_commit to track async updates") Fixes: 96260142 ("drm/fence: add in-fences support") Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by:
Gustavo Padovan <gustavo.padovan@collabora.com> Signed-off-by:
-
Lee, Shawn C authored
commit 789ea125 upstream. Add the missing INTEL_OUTPUT_DP_MST case in bxt_get_dpll() to correctly initialize the crtc_state and port plls when link training a DP MST monitor on BXT/APL devices. Fixes: a277ca7d ("drm/i915: Split bxt_ddi_pll_select()") Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=99572Reviewed-by:
Cooper Chiou <cooper.chiou@intel.com> Reviewed-by:
Gary C Wang <gary.c.wang@intel.com> Reviewed-by:
Ciobanu, Nathan D <nathan.d.ciobanu@intel.com> Reviewed-by:
Herbert, Marc <marc.herbert@intel.com> Reviewed-by:
Bride, Jim <jim.bride@intel.com> Reviewed-by:
Navare, Manasi D <manasi.d.navare@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by:
Lee, Shawn C <shawn.c.lee@intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1486096329-6255-1-git-send-email-shawn.c.lee@intel.com (cherry picked from commit 0aab2c72) Signed-off-by:
-
Andrey Ryabinin authored
commit 5351fbb1 upstream. page_flip_completed() dereferences 'work' variable after executing queue_work(). This is not safe as the 'work' item might be already freed by queued work: BUG: KASAN: use-after-free in page_flip_completed+0x3ff/0x490 at addr ffff8803dc010f90 Call Trace: __asan_report_load8_noabort+0x59/0x80 page_flip_completed+0x3ff/0x490 intel_finish_page_flip_mmio+0xe3/0x130 intel_pipe_handle_vblank+0x2d/0x40 gen8_irq_handler+0x4a7/0xed0 __handle_irq_event_percpu+0xf6/0x860 handle_irq_event_percpu+0x6b/0x160 handle_irq_event+0xc7/0x1b0 handle_edge_irq+0x1f4/0xa50 handle_irq+0x41/0x70 do_IRQ+0x9a/0x200 common_interrupt+0x89/0x89 Freed: kfree+0x113/0x4d0 intel_unpin_work_fn+0x29a/0x3b0 process_one_work+0x79e/0x1b70 worker_thread+0x611/0x1460 kthread+0x241/0x3a0 ret_from_fork+0x27/0x40 Move queue_work() after trace_i915_flip_complete() to fix this. Fixes: e5510fac ("drm/i915: add tracepoints for flip requests & completions") Signed-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
-
Dave Martin authored
commit 228dbbfb upstream. Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET to fill all the registers, the thread's old registers are preserved. Fixes: 5be6f62b ("ARM: 6883/1: ptrace: Migrate to regsets framework") Signed-off-by:
Dave Martin <Dave.Martin@arm.com> Acked-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Arnd Bergmann authored
commit b3f2d07f upstream. The use of ACCESS_ONCE() looks like a micro-optimization to force gcc to use an indexed load for the register address, but it has an absolutely detrimental effect on builds with gcc-5 and CONFIG_KASAN=y, leading to a very likely kernel stack overflow aside from very complex object code: hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_update_stats': hisilicon/hns/hns_dsaf_gmac.c:419:1: error: the frame size of 2912 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_reset_common': hisilicon/hns/hns_dsaf_ppe.c:390:1: error: the frame size of 1184 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_get_regs': hisilicon/hns/hns_dsaf_ppe.c:621:1: error: the frame size of 3632 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_common_regs': hisilicon/hns/hns_dsaf_rcb.c:970:1: error: the frame size of 2784 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_get_regs': hisilicon/hns/hns_dsaf_gmac.c:641:1: error: the frame size of 5728 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_ring_regs': hisilicon/hns/hns_dsaf_rcb.c:1021:1: error: the frame size of 2208 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_comm_init': hisilicon/hns/hns_dsaf_main.c:1209:1: error: the frame size of 1904 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_xgmac.c: In function 'hns_xgmac_get_regs': hisilicon/hns/hns_dsaf_xgmac.c:748:1: error: the frame size of 4704 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_update_stats': hisilicon/hns/hns_dsaf_main.c:2420:1: error: the frame size of 1088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_regs': hisilicon/hns/hns_dsaf_main.c:2753:1: error: the frame size of 10768 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] This does not seem to happen any more with gcc-7, but removing the ACCESS_ONCE seems safe anyway and it avoids a serious issue for some people. I have verified that with gcc-5.3.1, the object code we get is better in the new version both with and without CONFIG_KASAN, as we no longer allocate a 1344 byte stack frame for hns_dsaf_get_regs() but otherwise have practically identical object code. With gcc-7.0.0, removing ACCESS_ONCE has no effect, the object code is already good either way. This patch is probably not urgent to get into 4.11 as only KASAN=y builds with certain compilers are affected, but I still think it makes sense to backport into older kernels. Fixes: 511e6bc0 ("net: add Hisilicon Network Subsystem DSAF support") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Bryant G. Ly authored
commit b22bc278 upstream. This patch adds internal LIO sgl limit since the driver already sets a max transfer limit on transport layer of 1MB to the client. Tested-by:
Steven Royer <seroyer@linux.vnet.ibm.com> Signed-off-by:
Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by:
-
Sean Rees authored
commit a810007a upstream. Commit 210e7a43 ("mm: SLUB freelist randomization") broke USB hub initialisation as described in https://bugzilla.kernel.org/show_bug.cgi?id=177551. Bail out early from init_cache_random_seq if s->random_seq is already initialised. This prevents destroying the previously computed random_seq offsets later in the function. If the offsets are destroyed, then shuffle_freelist will truncate page->freelist to just the first object (orphaning the rest). Fixes: 210e7a43 ("mm: SLUB freelist randomization") Link: http://lkml.kernel.org/r/20170207140707.20824-1-sean@erifax.orgSigned-off-by:
Sean Rees <sean@erifax.org> Reported-by: <userwithuid@gmail.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Thomas Garnier <thgarnie@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Tejun Heo authored
commit 4d59b6cc upstream. Commit 513e3d2d ("cpumask: always use nr_cpu_ids in formatting and parsing functions") converted both cpumask printing and parsing functions to use nr_cpu_ids instead of nr_cpumask_bits. While this was okay for the printing functions as it just picked one of the two output formats that we were alternating between depending on a kernel config, doing the same for parsing wasn't okay. nr_cpumask_bits can be either nr_cpu_ids or NR_CPUS. We can always use nr_cpu_ids but that is a variable while NR_CPUS is a constant, so it can be more efficient to use NR_CPUS when we can get away with it. Converting the printing functions to nr_cpu_ids makes sense because it affects how the masks get presented to userspace and doesn't break anything; however, using nr_cpu_ids for parsing functions can incorrectly leave the higher bits uninitialized while reading in these masks from userland. As all testing and comparison functions use nr_cpumask_bits which can be larger than nr_cpu_ids, the parsed cpumasks can erroneously yield false negative results. This made the taskstats interface incorrectly return -EINVAL even when the inputs were correct. Fix it by restoring the parse functions to use nr_cpumask_bits instead of nr_cpu_ids. Link: http://lkml.kernel.org/r/20170206182442.GB31078@htj.duckdns.org Fixes: 513e3d2d ("cpumask: always use nr_cpu_ids in formatting and parsing functions") Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
Martin Steigerwald <martin.steigerwald@teamix.de> Debugged-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Jurij Smakov authored
commit 52f5631a upstream. In commit cf4747d7 ("rtlwifi: Fix regression caused by commit d86e6476, an error in the edit results in the wrong firmware being loaded for some models of the RTL8188/8192CE. In this condition, the connection suffered from high ping latency, slow transfer rates, and required higher signal strengths to work at all See https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=853073, https://bugzilla.opensuse.org/show_bug.cgi?id=1017471, and https://github.com/lwfinger/rtlwifi_new/issues/203 for descriptions of the problems. This patch fixes all of those problems. Fixes: cf4747d7 ("rtlwifi: Fix regression caused by commit d86e6476") Signed-off-by:
Jurij Smakov <jurij@wooyd.org> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Linus Torvalds authored
commit d966564f upstream. This reverts commit 020eb3da. Gabriel C reports that it causes his machine to not boot, and we haven't tracked down the reason for it yet. Since the bug it fixes has been around for a longish time, we're better off reverting the fix for now. Gabriel says: "It hangs early and freezes with a lot RCU warnings. I bisected it down to : > Ruslan Ruslichenko (1): > x86/ioapic: Restore IO-APIC irq_chip retrigger callback Reverting this one fixes the problem for me.. The box is a PRIMERGY TX200 S5 , 2 socket , 2 x E5520 CPU(s) installed" and Ruslan and Thomas are currently stumped. Reported-and-bisected-by:
Gabriel C <nix.or.die@gmail.com> Cc: Ruslan Ruslichenko <rruslich@cisco.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Stephen Smalley authored
commit 0c461cb7 upstream. SELinux tries to support setting/clearing of /proc/pid/attr attributes from the shell by ignoring terminating newlines and treating an attribute value that begins with a NUL or newline as an attempt to clear the attribute. However, the test for clearing attributes has always been wrong; it has an off-by-one error, and this could further lead to reading past the end of the allocated buffer since commit bb646cdb ("proc_pid_attr_write(): switch to memdup_user()"). Fix the off-by-one error. Even with this fix, setting and clearing /proc/pid/attr attributes from the shell is not straightforward since the interface does not support multiple write() calls (so shells that write the value and newline separately will set and then immediately clear the attribute, requiring use of echo -n to set the attribute), whereas trying to use echo -n "" to clear the attribute causes the shell to skip the write() call altogether since POSIX says that a zero-length write causes no side effects. Thus, one must use echo -n to set and echo without -n to clear, as in the following example: $ echo -n unconfined_u:object_r:user_home_t:s0 > /proc/$$/attr/fscreate $ cat /proc/$$/attr/fscreate unconfined_u:object_r:user_home_t:s0 $ echo "" > /proc/$$/attr/fscreate $ cat /proc/$$/attr/fscreate Note the use of /proc/$$ rather than /proc/self, as otherwise the cat command will read its own attribute value, not that of the shell. There are no users of this facility to my knowledge; possibly we should just get rid of it. UPDATE: Upon further investigation it appears that a local process with the process:setfscreate permission can cause a kernel panic as a result of this bug. This patch fixes CVE-2017-2618. Signed-off-by:
Stephen Smalley <sds@tycho.nsa.gov> [PM: added the update about CVE-2017-2618 to the commit description] Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
James Morris <james.l.morris@oracle.com>
-
Dmitry Torokhov authored
commit 601bbbe0 upstream. If user tries to initialize uinput device mixing old and new style initialization (i.e. using old UI_SET_ABSBIT instead of UI_ABS_SETUP, we forget to allocate input->absinfo and will crash when trying to send absolute events: ioctl(ui, UI_DEV_SETUP, &us); ioctl(ui, UI_SET_PHYS, "Test"); ioctl(ui, UI_SET_EVBIT, EV_ABS); ioctl(ui, UI_SET_ABSBIT, ABS_X); ioctl(ui, UI_SET_ABSBIT, ABS_Y); ioctl(ui, UI_DEV_CREATE, 0); Reported-by:
Rodrigo Rivas Costa <rodrigorivascosta@gmail.com> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=191811 Fixes: fbae10db ("Input: uinput - rework ABS validation") Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Vineet Gupta authored
commit a524c218 upstream. Reported-by:
Jo-Philipp Wich <jo@mein.io> Fixes: 9aed02fe ("ARC: [arcompact] handle unaligned access delay slot") Cc: linux-kernel@vger.kernel.org Cc: linux-snps-arc@lists.infradead.org Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Gary R Hook authored
commit e5da5c56 upstream. Eliminate a double-add by creating a new list to manage command descriptors when created; move the descriptor to the pending list when the command is submitted. Signed-off-by:
Gary R Hook <gary.hook@amd.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Gary R Hook authored
commit 500c0106 upstream. An I/O page fault occurs when the IOMMU is enabled on a system that supports the v5 CCP. DMA operations use a Request ID value that does not match what is expected by the IOMMU, resulting in the I/O page fault. Setting the Request ID value to 0 corrects this issue. Signed-off-by:
-
Giovanni Cabiddu authored
commit 685ce062 upstream. Zero embedded ram in DH85x devices. This is not needed for newer generations as it is done by HW. Signed-off-by:
Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by:
-
Giovanni Cabiddu authored
commit 3484ecbe upstream. Some accelerators of the c62x series have only two bars. This patch skips BAR0 if the accelerator does not have it. Signed-off-by:
-
Harsh Jain authored
commit f5f7bebc upstream. Ensure dev is allocated for crypto uld context before using the device for crypto operations. Signed-off-by:
Atul Gupta <atul.gupta@chelsio.com> Signed-off-by:
-
Harsh Jain authored
commit 0b529f14 upstream. Kernel panics when userspace program try to access AEAD interface. Remove node from Linked List before freeing its memory. Signed-off-by:
Harsh Jain <harsh@chelsio.com> Reviewed-by:
Stephan Müller <smueller@chronox.de> Signed-off-by:
-
Mike Snitzer authored
commit 4087a1ff upstream. Fixes a crash in dm_table_find_target() due to a NULL struct dm_table being passed from dm_old_request_fn() that races with DM device destruction. Reported-by: artem@flashgrid.io Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Dan Williams authored
commit bfb34527 upstream. When vmemmap_populate() allocates space for the memmap it does so in 2MB sized chunks. The libnvdimm-pfn driver incorrectly accounts for this when the alignment of the device is set to 4K. When this happens we trigger memory allocation failures in altmap_alloc_block_buf() and trigger warnings of the form: WARNING: CPU: 0 PID: 3376 at arch/x86/mm/init_64.c:656 arch_add_memory+0xe4/0xf0 [..] Call Trace: dump_stack+0x86/0xc3 __warn+0xcb/0xf0 warn_slowpath_null+0x1d/0x20 arch_add_memory+0xe4/0xf0 devm_memremap_pages+0x29b/0x4e0 Fixes: 315c5625 ("libnvdimm, pfn: add 'align' attribute, default to HPAGE_SIZE") Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Dan Williams authored
commit 9d032f42 upstream. Given that the naming of pmem devices changes from the pmemX form to the pmemX.Y form when namespace id is greater than 0, arrange for namespaces with id-0 to be exempt from deletion. Otherwise a simple reconfiguration of an existing namespace to a new mode results in a name change of the resulting block device: # ndctl list --namespace=namespace1.0 { "dev":"namespace1.0", "mode":"raw", "size":2147483648, "uuid":"3dadf3dc-89b9-4b24-b20e-abc8a4707ce3", "blockdev":"pmem1" } # ndctl create-namespace --reconfig=namespace1.0 --mode=memory --force { "dev":"namespace1.1", "mode":"memory", "size":2111832064, "uuid":"7b4a6341-7318-4219-a02c-fb57c0bbf613", "blockdev":"pmem1.1" } This change does require tooling changes to explicitly look for namespaceX.0 if the seed has already advanced to another namespace. Fixes: 98a29c39 ("libnvdimm, namespace: allow creation of multiple pmem-namespaces per region") Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
-
Dan Williams authored
commit e471486c upstream. We queue an on-stack work item to 'nfit_wq' and wait for it to complete as part of a 'flush_probe' request. However, if the user cancels the wait we need to make sure the item is flushed from the queue otherwise we are leaving an out-of-scope stack address on the work list. BUG: unable to handle kernel paging request at ffffbcb3c72f7cd0 IP: [<ffffffffa9413a7b>] __list_add+0x1b/0xb0 [..] RIP: 0010:[<ffffffffa9413a7b>] [<ffffffffa9413a7b>] __list_add+0x1b/0xb0 RSP: 0018:ffffbcb3c7ba7c00 EFLAGS: 00010046 [..] Call Trace: [<ffffffffa90bb11a>] insert_work+0x3a/0xc0 [<ffffffffa927fdda>] ? seq_open+0x5a/0xa0 [<ffffffffa90bb30a>] __queue_work+0x16a/0x460 [<ffffffffa90bbb08>] queue_work_on+0x38/0x40 [<ffffffffc0cf2685>] acpi_nfit_flush_probe+0x95/0xc0 [nfit] [<ffffffffc0cf25d0>] ? nfit_visible+0x40/0x40 [nfit] [<ffffffffa9571495>] wait_probe_show+0x25/0x60 [<ffffffffa9546b30>] dev_attr_show+0x20/0x50 Fixes: 7ae0fa43 ("nfit, libnvdimm: async region scrub workqueue") Reviewed-by:
Vishal Verma <vishal.l.verma@intel.com> Signed-off-by:
-
Srinivas Pandruvada authored
commit 6e978b22 upstream. Some Kabylake desktop processors may not reach max turbo when running in HWP mode, even if running under sustained 100% utilization. This occurs when the HWP.EPP (Energy Performance Preference) is set to "balance_power" (0x80) -- the default on most systems. It occurs because the platform BIOS may erroneously enable an energy-efficiency setting -- MSR_IA32_POWER_CTL BIT-EE, which is not recommended to be enabled on this SKU. On the failing systems, this BIOS issue was not discovered when the desktop motherboard was tested with Windows, because the BIOS also neglects to provide the ACPI/CPPC table, that Windows requires to enable HWP, and so Windows runs in legacy P-state mode, where this setting has no effect. Linux' intel_pstate driver does not require ACPI/CPPC to enable HWP, and so it runs in HWP mode, exposing this incorrect BIOS configuration. There are several ways to address this problem. First, Linux can also run in legacy P-state mode on this system. As intel_pstate is how Linux enables HWP, booting with "intel_pstate=disable" will run in acpi-cpufreq/ondemand legacy p-state mode. Or second, the "performance" governor can be used with intel_pstate, which will modify HWP.EPP to 0. Or third, starting in 4.10, the /sys/devices/system/cpu/cpufreq/policy*/energy_performance_preference attribute in can be updated from "balance_power" to "performance". Or fourth, apply this patch, which fixes the erroneous setting of MSR_IA32_POWER_CTL BIT_EE on this model, allowing the default configuration to function as designed. Signed-off-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Reviewed-by:
Len Brown <len.brown@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
- 09 Feb, 2017 10 commits
-
-
Greg Kroah-Hartman authored
-
Chris Wilson authored
commit bafb2f7d upstream. There is a disparity in the context image saved to disk and our own bookkeeping - that is we presume the RING_HEAD and RING_TAIL match our stored ce->ring->tail value. However, as we emit WA_TAIL_DWORDS into the ring but may not tell the GPU about them, the GPU may be lagging behind our bookkeeping. Upon hibernation we do not save stolen pages, presuming that their contents are volatile. This means that although we start writing into the ring at tail, the GPU starts executing from its HEAD and there may be some garbage in between and so the GPU promptly hangs upon resume. Testcase: igt/gem_exec_suspend/basic-S4 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96526Signed-off-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20160921135108.29574-3-chris@chris-wilson.co.uk Cc: Eric Blau <eblau1@gmail.com> Signed-off-by:
-
Michal Hocko authored
commit d1908f52 upstream. Tetsuo has noticed that an OOM stress test which performs large write requests can cause the full memory reserves depletion. He has tracked this down to the following path __alloc_pages_nodemask+0x436/0x4d0 alloc_pages_current+0x97/0x1b0 __page_cache_alloc+0x15d/0x1a0 mm/filemap.c:728 pagecache_get_page+0x5a/0x2b0 mm/filemap.c:1331 grab_cache_page_write_begin+0x23/0x40 mm/filemap.c:2773 iomap_write_begin+0x50/0xd0 fs/iomap.c:118 iomap_write_actor+0xb5/0x1a0 fs/iomap.c:190 ? iomap_write_end+0x80/0x80 fs/iomap.c:150 iomap_apply+0xb3/0x130 fs/iomap.c:79 iomap_file_buffered_write+0x68/0xa0 fs/iomap.c:243 ? iomap_write_end+0x80/0x80 xfs_file_buffered_aio_write+0x132/0x390 [xfs] ? remove_wait_queue+0x59/0x60 xfs_file_write_iter+0x90/0x130 [xfs] __vfs_write+0xe5/0x140 vfs_write+0xc7/0x1f0 ? syscall_trace_enter+0x1d0/0x380 SyS_write+0x58/0xc0 do_syscall_64+0x6c/0x200 entry_SYSCALL64_slow_path+0x25/0x25 the oom victim has access to all memory reserves to make a forward progress to exit easier. But iomap_file_buffered_write and other callers of iomap_apply loop to complete the full request. We need to check for fatal signals and back off with a short write instead. As the iomap_apply delegates all the work down to the actor we have to hook into those. All callers that work with the page cache are calling iomap_write_begin so we will check for signals there. dax_iomap_actor has to handle the situation explicitly because it copies data to the userspace directly. Other callers like iomap_page_mkwrite work on a single page or iomap_fiemap_actor do not allocate memory based on the given len. Fixes: 68a9f5e7 ("xfs: implement iomap based buffered write path") Link: http://lkml.kernel.org/r/20170201092706.9966-2-mhocko@kernel.orgSigned-off-by:
Michal Hocko <mhocko@suse.com> Reported-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by:
-
Steve Wise authored
commit b414fa01 upstream. The current QP FetchBurstMax value is 256B, which is incorrect since a WR can exceed that value. The result being a partial WR fetched by hardware, and a fatal "bad WR" error posted by the SGE. So bump the FetchBurstMax to 512B. Signed-off-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Thomas Gleixner authored
commit aaaec6fc upstream. The recent commit which prevents double activation of interrupts unearthed interesting code in x86. The code (ab)uses irq_domain_activate_irq() to reconfigure an already activated interrupt. That trips over the prevention code now. Fix it by deactivating the interrupt before activating the new configuration. Fixes: 08d85f3e "irqdomain: Avoid activating interrupts more than once" Reported-and-tested-by:
Mike Galbraith <efault@gmx.de> Reported-and-tested-by:
Borislav Petkov <bp@alien8.de> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1701311901580.3457@nanosSigned-off-by:
-
Marc Zyngier authored
commit 08d85f3e upstream. Since commit f3b0946d ("genirq/msi: Make sure PCI MSIs are activated early"), we can end-up activating a PCI/MSI twice (once at allocation time, and once at startup time). This is normally of no consequences, except that there is some HW out there that may misbehave if activate is used more than once (the GICv3 ITS, for example, uses the activate callback to issue the MAPVI command, and the architecture spec says that "If there is an existing mapping for the EventID-DeviceID combination, behavior is UNPREDICTABLE"). While this could be worked around in each individual driver, it may make more sense to tackle the issue at the core level. In order to avoid getting in that situation, let's have a per-interrupt flag to remember if we have already activated that interrupt or not. Fixes: f3b0946d ("genirq/msi: Make sure PCI MSIs are activated early") Reported-and-tested-by:
Andre Przywara <andre.przywara@arm.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Link: http://lkml.kernel.org/r/1484668848-24361-1-git-send-email-marc.zyngier@arm.comSigned-off-by:
-
Matt Ranostay authored
commit 828f84ee upstream. FIFO was being read every sample after the "almost full" state was reached. This was due to an incorrect placement of the parenthesis in the while condition check. Note - the fixes tag is not actually correct, but the fix in this patch would also be needed for it to function correctly so we'll go with that one. Backports should pick up both. Signed-off-by:
Matt Ranostay <matt@ranostay.consulting> Fixes: b74fccad ("iio: health: max30100: correct FIFO check condition") Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
John Brooks authored
commit 5c113b5e upstream. The DHT22 (AM2302) datasheet specifies that the LOW start pulse should not exceed 20ms. However, observations with an oscilloscope of an RPi Model 2B (rev 1.1) communicating with a DHT22 sensor showed that the driver was consistently sending start pulses longer than 20ms: Kernel 4.7.10-v7+ (n=132): Minimum pulse length: 20.20ms Maximum: 29.84ms Mean: 24.96ms StDev: 2.82ms Sensor response rate: 100% Read success rate: 76% On kernel 4.8, the start pulse was so long that the sensor would not even respond 97% of the time: Kernel 4.8.16-v7+ (n=100): Minimum pulse length: 30.4ms Maximum: 74.4ms Mean: 39.3ms StDev: 10.2ms Sensor response rate: 3% Read success rate: 3% The driver would return ETIMEDOUT and write log messages like this: [ 51.430987] dht11 dht11@0: Only 1 signal edges detected [ 66.311019] dht11 dht11@0: Only 0 signal edges detected Replacing msleep(18) with usleep_range(18000, 20000) made the pulse length sane again and restored responsiveness: Kernel 4.8.16-v7+ with usleep_range (n=123): Minimum pulse length: 18.16ms Maximum: 20.20ms Mean: 19.85ms StDev: 0.51ms Sensor response rate: 100% Read success rate: 84% Signed-off-by:
John Brooks <john@fastquake.com> Reviewed-by:
Harald Geyer <harald@ccbib.org> Signed-off-by:
-
Alison Schofield authored
commit a5badd1e upstream. The suspend/resume functions were using dev_to_iio_dev() to get the iio_dev. That only works on IIO dev's. Replace it with spi functions to get the correct iio_dev. Signed-off-by:
Alison Schofield <amsfield22@gmail.com> Acked-by:
Andrew F. Davis <afd@ti.com> Signed-off-by:
-
Alison Schofield authored
commit 802ecfc1 upstream. The suspend/resume functions were using dev_to_iio_dev() to get the iio_dev. That only works on IIO dev's. Replace it with i2c functions to get the correct iio_dev. Signed-off-by:
-
