- 10 Sep, 2017 40 commits
-
-
Florian Fainelli authored
[ Upstream commit 7ad813f2 ] Marc reported that he was not getting the PHY library adjust_link() callback function to run when calling phy_stop() + phy_disconnect() which does not indeed happen because we set the state machine to PHY_HALTED but we don't get to run it to process this state past that point. Fix this with a synchronous call to phy_state_machine() in order to have the state machine actually act on PHY_HALTED, set the PHY device's link down, turn the network device's carrier off and finally call the adjust_link() function. Reported-by:
Marc Gonzalez <marc_gonzalez@sigmadesigns.com> Fixes: a390d1f3 ("phylib: convert state_queue work to delayed_work") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com>
-
Xin Long authored
[ Upstream commit 6b84202c ] Commit b1f5bfc2 ("sctp: don't dereference ptr before leaving _sctp_walk_{params, errors}()") tried to fix the issue that it may overstep the chunk end for _sctp_walk_{params, errors} with 'chunk_end > offset(length) + sizeof(length)'. But it introduced a side effect: When processing INIT, it verifies the chunks with 'param.v == chunk_end' after iterating all params by sctp_walk_params(). With the check 'chunk_end > offset(length) + sizeof(length)', it would return when the last param is not yet accessed. Because the last param usually is fwdtsn supported param whose size is 4 and 'chunk_end == offset(length) + sizeof(length)' This is a badly issue even causing sctp couldn't process 4-shakes. Client would always get abort when connecting to server, due to the failure of INIT chunk verification on server. The patch is to use 'chunk_end <= offset(length) + sizeof(length)' instead of 'chunk_end < offset(length) + sizeof(length)' for both _sctp_walk_params and _sctp_walk_errors. Fixes: b1f5bfc2 ("sctp: don't dereference ptr before leaving _sctp_walk_{params, errors}()") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Alexander Potapenko authored
[ Upstream commit b1f5bfc2 ] If the length field of the iterator (|pos.p| or |err|) is past the end of the chunk, we shouldn't access it. This bug has been detected by KMSAN. For the following pair of system calls: socket(PF_INET6, SOCK_STREAM, 0x84 /* IPPROTO_??? */) = 3 sendto(3, "A", 1, MSG_OOB, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = 1 the tool has reported a use of uninitialized memory: ================================================================== BUG: KMSAN: use of uninitialized memory in sctp_rcv+0x17b8/0x43b0 CPU: 1 PID: 2940 Comm: probe Not tainted 4.11.0-rc5+ #2926 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:16 dump_stack+0x172/0x1c0 lib/dump_stack.c:52 kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:927 __msan_warning_32+0x61/0xb0 mm/kmsan/kmsan_instr.c:469 __sctp_rcv_init_lookup net/sctp/input.c:1074 __sctp_rcv_lookup_harder net/sctp/input.c:1233 __sctp_rcv_lookup net/sctp/input.c:1255 sctp_rcv+0x17b8/0x43b0 net/sctp/input.c:170 sctp6_rcv+0x32/0x70 net/sctp/ipv6.c:984 ip6_input_finish+0x82f/0x1ee0 net/ipv6/ip6_input.c:279 NF_HOOK ./include/linux/netfilter.h:257 ip6_input+0x239/0x290 net/ipv6/ip6_input.c:322 dst_input ./include/net/dst.h:492 ip6_rcv_finish net/ipv6/ip6_input.c:69 NF_HOOK ./include/linux/netfilter.h:257 ipv6_rcv+0x1dbd/0x22e0 net/ipv6/ip6_input.c:203 __netif_receive_skb_core+0x2f6f/0x3a20 net/core/dev.c:4208 __netif_receive_skb net/core/dev.c:4246 process_backlog+0x667/0xba0 net/core/dev.c:4866 napi_poll net/core/dev.c:5268 net_rx_action+0xc95/0x1590 net/core/dev.c:5333 __do_softirq+0x485/0x942 kernel/softirq.c:284 do_softirq_own_stack+0x1c/0x30 arch/x86/entry/entry_64.S:902 </IRQ> do_softirq kernel/softirq.c:328 __local_bh_enable_ip+0x25b/0x290 kernel/softirq.c:181 local_bh_enable+0x37/0x40 ./include/linux/bottom_half.h:31 rcu_read_unlock_bh ./include/linux/rcupdate.h:931 ip6_finish_output2+0x19b2/0x1cf0 net/ipv6/ip6_output.c:124 ip6_finish_output+0x764/0x970 net/ipv6/ip6_output.c:149 NF_HOOK_COND ./include/linux/netfilter.h:246 ip6_output+0x456/0x520 net/ipv6/ip6_output.c:163 dst_output ./include/net/dst.h:486 NF_HOOK ./include/linux/netfilter.h:257 ip6_xmit+0x1841/0x1c00 net/ipv6/ip6_output.c:261 sctp_v6_xmit+0x3b7/0x470 net/sctp/ipv6.c:225 sctp_packet_transmit+0x38cb/0x3a20 net/sctp/output.c:632 sctp_outq_flush+0xeb3/0x46e0 net/sctp/outqueue.c:885 sctp_outq_uncork+0xb2/0xd0 net/sctp/outqueue.c:750 sctp_side_effects net/sctp/sm_sideeffect.c:1773 sctp_do_sm+0x6962/0x6ec0 net/sctp/sm_sideeffect.c:1147 sctp_primitive_ASSOCIATE+0x12c/0x160 net/sctp/primitive.c:88 sctp_sendmsg+0x43e5/0x4f90 net/sctp/socket.c:1954 inet_sendmsg+0x498/0x670 net/ipv4/af_inet.c:762 sock_sendmsg_nosec net/socket.c:633 sock_sendmsg net/socket.c:643 SYSC_sendto+0x608/0x710 net/socket.c:1696 SyS_sendto+0x8a/0xb0 net/socket.c:1664 do_syscall_64+0xe6/0x130 arch/x86/entry/common.c:285 entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.S:246 RIP: 0033:0x401133 RSP: 002b:00007fff6d99cd38 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00000000004002b0 RCX: 0000000000401133 RDX: 0000000000000001 RSI: 0000000000494088 RDI: 0000000000000003 RBP: 00007fff6d99cd90 R08: 00007fff6d99cd50 R09: 000000000000001c R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000000 R13: 00000000004063d0 R14: 0000000000406460 R15: 0000000000000000 origin: save_stack_trace+0x37/0x40 arch/x86/kernel/stacktrace.c:59 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:302 kmsan_internal_poison_shadow+0xb1/0x1a0 mm/kmsan/kmsan.c:198 kmsan_poison_shadow+0x6d/0xc0 mm/kmsan/kmsan.c:211 slab_alloc_node mm/slub.c:2743 __kmalloc_node_track_caller+0x200/0x360 mm/slub.c:4351 __kmalloc_reserve net/core/skbuff.c:138 __alloc_skb+0x26b/0x840 net/core/skbuff.c:231 alloc_skb ./include/linux/skbuff.h:933 sctp_packet_transmit+0x31e/0x3a20 net/sctp/output.c:570 sctp_outq_flush+0xeb3/0x46e0 net/sctp/outqueue.c:885 sctp_outq_uncork+0xb2/0xd0 net/sctp/outqueue.c:750 sctp_side_effects net/sctp/sm_sideeffect.c:1773 sctp_do_sm+0x6962/0x6ec0 net/sctp/sm_sideeffect.c:1147 sctp_primitive_ASSOCIATE+0x12c/0x160 net/sctp/primitive.c:88 sctp_sendmsg+0x43e5/0x4f90 net/sctp/socket.c:1954 inet_sendmsg+0x498/0x670 net/ipv4/af_inet.c:762 sock_sendmsg_nosec net/socket.c:633 sock_sendmsg net/socket.c:643 SYSC_sendto+0x608/0x710 net/socket.c:1696 SyS_sendto+0x8a/0xb0 net/socket.c:1664 do_syscall_64+0xe6/0x130 arch/x86/entry/common.c:285 return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.S:246 ================================================================== Signed-off-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit e90ce2fc ] In dccp_feat_init, when ccid_get_builtin_ccids failsto alloc memory for rx.val, it should free tx.val before returning an error. Signed-off-by:
-
Xin Long authored
[ Upstream commit b7953d3c ] The patch "dccp: fix a memleak that dccp_ipv6 doesn't put reqsk properly" fixed reqsk refcnt leak for dccp_ipv6. The same issue exists on dccp_ipv4. This patch is to fix it for dccp_ipv4. Signed-off-by:
-
WANG Cong authored
[ Upstream commit c800aaf8 ] There are multiple reports showing we have a use-after-free in the timer prb_retire_rx_blk_timer_expired(), where we use struct tpacket_kbdq_core::pkbdq, a pg_vec, after it gets freed by free_pg_vec(). The interesting part is it is not freed via packet_release() but via packet_setsockopt(), which means we are not closing the socket. Looking into the big and fat function packet_set_ring(), this could happen if we satisfy the following conditions: 1. closing == 0, not on packet_release() path 2. req->tp_block_nr == 0, we don't allocate a new pg_vec 3. rx_ring->pg_vec is already set as V3, which means we already called packet_set_ring() wtih req->tp_block_nr > 0 previously 4. req->tp_frame_nr == 0, pass sanity check 5. po->mapped == 0, never called mmap() In this scenario we are clearing the old rx_ring->pg_vec, so we need to free this pg_vec, but we don't stop the timer on this path because of closing==0. The timer has to be stopped as long as we need to free pg_vec, therefore the check on closing!=0 is wrong, we should check pg_vec!=NULL instead. Thanks to liujian for testing different fixes. Reported-by: alexander.levin@verizon.com Reported-by:
Dave Jones <davej@codemonkey.org.uk> Reported-by:
liujian (CE) <liujian56@huawei.com> Tested-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Thomas Jarosch authored
[ Upstream commit 9476d393 ] DMA transfers are not allowed to buffers that are on the stack. Therefore allocate a buffer to store the result of usb_control_message(). Fixes these bugreports: https://bugzilla.kernel.org/show_bug.cgi?id=195217 https://bugzilla.redhat.com/show_bug.cgi?id=1421387 https://bugzilla.redhat.com/show_bug.cgi?id=1427398 Shortened kernel backtrace from 4.11.9-200.fc25.x86_64: kernel: ------------[ cut here ]------------ kernel: WARNING: CPU: 3 PID: 2957 at drivers/usb/core/hcd.c:1587 kernel: transfer buffer not dma capable kernel: Call Trace: kernel: dump_stack+0x63/0x86 kernel: __warn+0xcb/0xf0 kernel: warn_slowpath_fmt+0x5a/0x80 kernel: usb_hcd_map_urb_for_dma+0x37f/0x570 kernel: ? try_to_del_timer_sync+0x53/0x80 kernel: usb_hcd_submit_urb+0x34e/0xb90 kernel: ? schedule_timeout+0x17e/0x300 kernel: ? del_timer_sync+0x50/0x50 kernel: ? __slab_free+0xa9/0x300 kernel: usb_submit_urb+0x2f4/0x560 kernel: ? urb_destroy+0x24/0x30 kernel: usb_start_wait_urb+0x6e/0x170 kernel: usb_control_msg+0xdc/0x120 kernel: mcs_get_reg+0x36/0x40 [mcs7780] kernel: mcs_net_open+0xb5/0x5c0 [mcs7780] ... Regression goes back to 4.9, so it's a good candidate for -stable. Though it's the decision of the maintainer. Thanks to Dan Williams for adding the "transfer buffer not dma capable" warning in the first place. It instantly pointed me in the right direction. Patch has been tested with transferring data from a Polar watch. Signed-off-by:
Thomas Jarosch <thomas.jarosch@intra2net.com> Signed-off-by:
-
WANG Cong authored
[ Upstream commit 153711f9 ] virtnet_set_mac_address() interprets mac address as struct sockaddr, but upper layer only allocates dev->addr_len which is ETH_ALEN + sizeof(sa_family_t) in this case. We lack a unified definition for mac address, so just fix the upper layer, this also allows drivers to interpret it to struct sockaddr freely. Reported-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Mahesh Bandewar authored
[ Upstream commit 8799a221 ] Net stack initialization currently initializes fib-trie after the first call to netdevice_notifier() call. In fact fib_trie initialization needs to happen before first rtnl_register(). It does not cause any problem since there are no devices UP at this moment, but trying to bring 'lo' UP at initialization would make this assumption wrong and exposes the issue. Fixes following crash Call Trace: ? alternate_node_alloc+0x76/0xa0 fib_table_insert+0x1b7/0x4b0 fib_magic.isra.17+0xea/0x120 fib_add_ifaddr+0x7b/0x190 fib_netdev_event+0xc0/0x130 register_netdevice_notifier+0x1c1/0x1d0 ip_fib_init+0x72/0x85 ip_rt_init+0x187/0x1e9 ip_init+0xe/0x1a inet_init+0x171/0x26c ? ipv4_offload_init+0x66/0x66 do_one_initcall+0x43/0x160 kernel_init_freeable+0x191/0x219 ? rest_init+0x80/0x80 kernel_init+0xe/0x150 ret_from_fork+0x22/0x30 Code: f6 46 23 04 74 86 4c 89 f7 e8 ae 45 01 00 49 89 c7 4d 85 ff 0f 85 7b ff ff ff 31 db eb 08 4c 89 ff e8 16 47 01 00 48 8b 44 24 38 <45> 8b 6e 14 4d 63 76 74 48 89 04 24 0f 1f 44 00 00 48 83 c4 08 RIP: kmem_cache_alloc+0xcf/0x1c0 RSP: ffff9b1500017c28 CR2: 0000000000000014 Fixes: 7b1a74fd ("[NETNS]: Refactor fib initialization so it can handle multiple namespaces.") Fixes: 7f9b8052 ("[IPV4]: fib hash|trie initialization") Signed-off-by:
Mahesh Bandewar <maheshb@google.com> Acked-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Sabrina Dubroca authored
[ Upstream commit 6399f1fa ] In some cases, offset can overflow and can cause an infinite loop in ip6_find_1stfragopt(). Make it unsigned int to prevent the overflow, and cap it at IPV6_MAXPLEN, since packets larger than that should be invalid. This problem has been here since before the beginning of git history. Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 63679112 ] The ifr.ifr_name is passed around and assumed to be NULL terminated. Signed-off-by:
-
Steven Toth authored
[ Upstream commit 6fb05e0d ] Avoid a double fetch by reusing the values from the prior transfer. Originally reported via https://bugzilla.kernel.org/show_bug.cgi?id=195559 Thanks to Pengfei Wang <wpengfeinudt@gmail.com> for reporting. Signed-off-by:
Steven Toth <stoth@kernellabs.com> Reported-by:
Pengfei Wang <wpengfeinudt@gmail.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Jin Qian authored
[ Upstream commit 15d3042a ] Make sure segno and blkoff read from raw image are valid. Cc: stable@vger.kernel.org Signed-off-by:
Jin Qian <jinqian@google.com> [Jaegeuk Kim: adjust minor coding style] Signed-off-by:
Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
-
Sean Young authored
[ Upstream commit 9f5039ba ] Since commit e8f48188 ("[media] lirc: advertise LIRC_CAN_GET_REC_RESOLUTION and improve") lircd uses the ioctl LIRC_GET_REC_RESOLUTION to determine the shortest pulse or space that the hardware can detect. This breaks decoding in lirc because lircd expects the answer in microseconds, but nanoseconds is returned. Cc: <stable@vger.kernel.org> # v2.6.36+ Reported-by:
Derek <user.vdr@gmail.com> Tested-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Nicholas Bellinger authored
[ Upstream commit fce50a2f ] This patch fixes a NULL pointer dereference in isert_login_recv_done() of isert_conn->cm_id due to isert_cma_handler() -> isert_connect_error() resetting isert_conn->cm_id = NULL during a failed login attempt. As per Sagi, we will always see the completion of all recv wrs posted on the qp (given that we assigned a ->done handler), this is a FLUSH error completion, we just don't get to verify that because we deref NULL before. The issue here, was the assumption that dereferencing the connection cm_id is always safe, which is not true since: commit 4a579da2 Author: Sagi Grimberg <sagig@mellanox.com> Date: Sun Mar 29 15:52:04 2015 +0300 iser-target: Fix possible deadlock in RDMA_CM connection error As I see it, we have a direct reference to the isert_device from isert_conn which is the one-liner fix that we actually need like we do in isert_rdma_read_done() and isert_rdma_write_done(). Reported-by:
Andrea Righi <righi.andrea@gmail.com> Tested-by:
Sagi Grimberg <sagi@grimberg.me> Cc: <stable@vger.kernel.org> # 3.10+ Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
[ Upstream commit 105fa2f4 ] This patch fixes a BUG() in iscsit_close_session() that could be triggered when iscsit_logout_post_handler() execution from within tx thread context was not run for more than SECONDS_FOR_LOGOUT_COMP (15 seconds), and the TCP connection didn't already close before then forcing tx thread context to automatically exit. This would manifest itself during explicit logout as: [33206.974254] 1 connection(s) still exist for iSCSI session to iqn.1993-08.org.debian:01:3f5523242179 [33206.980184] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 2100.772 msecs [33209.078643] ------------[ cut here ]------------ [33209.078646] kernel BUG at drivers/target/iscsi/iscsi_target.c:4346! Normally when explicit logout attempt fails, the tx thread context exits and iscsit_close_connection() from rx thread context does the extra cleanup once it detects conn->conn_logout_remove has not been cleared by the logout type specific post handlers. To address this special case, if the logout post handler in tx thread context detects conn->tx_thread_active has already been cleared, simply return and exit in order for existing iscsit_close_connection() logic from rx thread context do failed logout cleanup. Reported-by:
Bart Van Assche <bart.vanassche@sandisk.com> Tested-by:
Gary Guo <ghg@datera.io> Tested-by:
Chu Yuan Lin <cyl@datera.io> Signed-off-by:
-
Prabhakar Lad authored
[ Upstream commit da05d52d ] this patch makes sure VPFE_CMD_S_CCDC_RAW_PARAMS ioctl no longer works for vpfe_capture driver with a minimal patch suitable for backporting. - This ioctl was never in public api and was only defined in kernel header. - The function set_params constantly mixes up pointers and phys_addr_t numbers. - This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is described as an 'experimental ioctl that will change in future kernels'. - The code to allocate the table never gets called after we copy_from_user the user input over the kernel settings, and then compare them for inequality. - We then go on to use an address provided by user space as both the __user pointer for input and pass it through phys_to_virt to come up with a kernel pointer to copy the data to. This looks like a trivially exploitable root hole. Due to these reasons we make sure this ioctl now returns -EINVAL and backport this patch as far as possible. Fixes: 5f15fbb6 ("V4L/DVB (12251): v4l: dm644x ccdc module for vpfe capture driver") Signed-off-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Cc: <stable@vger.kernel.org> # for v3.7 and up Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Gregory CLEMENT authored
[ Upstream commit 8d451417 ] As written in the datasheet the PCA955 can only handle low level irq and not edge irq. Without this fix the interrupt is not usable for pca955: the gpio-pca953x driver already set the irq type as low level which is incompatible with edge type, then the kernel prevents using the interrupt: "irq: type mismatch, failed to map hwirq-18 for /soc/internal-regs/gpio@18100!" Fixes: 928413bd ("ARM: mvebu: Add Armada 388 General Purpose Development Board support") Cc: stable@vger.kernel.org Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Jerry Lee authored
[ Upstream commit aec51758 ] On a 32-bit platform, the value of n_blcoks_count may be wrong during the file system is resized to size larger than 2^32 blocks. This may caused the superblock being corrupted with zero blocks count. Fixes: 1c6bd717Signed-off-by:
Jerry Lee <jerrylee@qnap.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Cc: stable@vger.kernel.org # 3.7+ Signed-off-by:
-
Jan Kara authored
[ Upstream commit fcf5ea10 ] ext4_find_unwritten_pgoff() does not properly handle a situation when starting index is in the middle of a page and blocksize < pagesize. The following command shows the bug on filesystem with 1k blocksize: xfs_io -f -c "falloc 0 4k" \ -c "pwrite 1k 1k" \ -c "pwrite 3k 1k" \ -c "seek -a -r 0" foo In this example, neither lseek(fd, 1024, SEEK_HOLE) nor lseek(fd, 2048, SEEK_DATA) will return the correct result. Fix the problem by neglecting buffers in a page before starting offset. Reported-by:
Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by:
Jan Kara <jack@suse.cz> CC: stable@vger.kernel.org # 3.8+ Signed-off-by:
-
Josh Poimboeuf authored
[ Upstream commit adb1fe9a ] Linus suggested we try to remove some of the low-hanging fruit related to kernel address exposure in dmesg. The only leaks I see on my local system are: Freeing SMP alternatives memory: 32K (ffffffff9e309000 - ffffffff9e311000) Freeing initrd memory: 10588K (ffffa0b736b42000 - ffffa0b737599000) Freeing unused kernel memory: 3592K (ffffffff9df87000 - ffffffff9e309000) Freeing unused kernel memory: 1352K (ffffa0b7288ae000 - ffffa0b728a00000) Freeing unused kernel memory: 632K (ffffa0b728d62000 - ffffa0b728e00000) Linus says: "I suspect we should just remove [the addresses in the 'Freeing' messages]. I'm sure they are useful in theory, but I suspect they were more useful back when the whole "free init memory" was originally done. These days, if we have a use-after-free, I suspect the init-mem situation is the easiest situation by far. Compared to all the dynamic allocations which are much more likely to show it anyway. So having debug output for that case is likely not all that productive." With this patch the freeing messages now look like this: Freeing SMP alternatives memory: 32K Freeing initrd memory: 10588K Freeing unused kernel memory: 3592K Freeing unused kernel memory: 1352K Freeing unused kernel memory: 632K Suggested-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/6836ff90c45b71d38e5d4405aec56fa9e5d1d4b2.1477405374.git.jpoimboe@redhat.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Wanpeng Li authored
[ Upstream commit 337c017c ] WARNING: CPU: 5 PID: 1242 at kernel/rcu/tree_plugin.h:323 rcu_note_context_switch+0x207/0x6b0 CPU: 5 PID: 1242 Comm: unity-settings- Not tainted 4.13.0-rc2+ #1 RIP: 0010:rcu_note_context_switch+0x207/0x6b0 Call Trace: __schedule+0xda/0xba0 ? kvm_async_pf_task_wait+0x1b2/0x270 schedule+0x40/0x90 kvm_async_pf_task_wait+0x1cc/0x270 ? prepare_to_swait+0x22/0x70 do_async_page_fault+0x77/0xb0 ? do_async_page_fault+0x77/0xb0 async_page_fault+0x28/0x30 RIP: 0010:__d_lookup_rcu+0x90/0x1e0 I encounter this when trying to stress the async page fault in L1 guest w/ L2 guests running. Commit 9b132fbe (Add rcu user eqs exception hooks for async page fault) adds rcu_irq_enter/exit() to kvm_async_pf_task_wait() to exit cpu idle eqs when needed, to protect the code that needs use rcu. However, we need to call the pair even if the function calls schedule(), as seen from the above backtrace. This patch fixes it by informing the RCU subsystem exit/enter the irq towards/away from idle for both n.halted and !n.halted. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: stable@vger.kernel.org Signed-off-by:
Wanpeng Li <wanpeng.li@hotmail.com> Reviewed-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Banajit Goswami authored
[ Upstream commit b1cd2e34 ] Multiple frontend dailinks may be connected to a backend dailink at the same time. When one of frontend dailinks is closed, the associated backend dailink should not be closed if it is connected to other active frontend dailinks. Change ensures that backend dailink is closed only after all connected frontend dailinks are closed. Signed-off-by:
Gopikrishnaiah Anandan <agopik@codeaurora.org> Signed-off-by:
Banajit Goswami <bgoswami@codeaurora.org> Signed-off-by:
Patrick Lai <plai@codeaurora.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Sergei A. Trusov authored
[ Upstream commit 3f3c3714 ] Sony VAIO VPCL14M1R needs the quirk to make the speaker working properly. Tested-by:
Dmitriy <mexx400@yandex.ru> Cc: <stable@vger.kernel.org> Signed-off-by:
Sergei A. Trusov <sergei.a.trusov@ya.ru> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Tejun Heo authored
[ Upstream commit 5c0338c6 ] The combination of WQ_UNBOUND and max_active == 1 used to imply ordered execution. After NUMA affinity 4c16bd32 ("workqueue: implement NUMA affinity for unbound workqueues"), this is no longer true due to per-node worker pools. While the right way to create an ordered workqueue is alloc_ordered_workqueue(), the documentation has been misleading for a long time and people do use WQ_UNBOUND and max_active == 1 for ordered workqueues which can lead to subtle bugs which are very difficult to trigger. It's unlikely that we'd see noticeable performance impact by enforcing ordering on WQ_UNBOUND / max_active == 1 workqueues. Let's automatically set __WQ_ORDERED for those workqueues. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
Christoph Hellwig <hch@infradead.org> Reported-by:
Alexei Potashnik <alexei@purestorage.com> Fixes: 4c16bd32 ("workqueue: implement NUMA affinity for unbound workqueues") Cc: stable@vger.kernel.org # v3.10+ Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 59a5e266 ] My static checker complains that "devno" can be negative, meaning that we read before the start of the loop. I've looked at the code, and I think the warning is right. This come from /proc so it's root only or it would be quite a quite a serious bug. The call tree looks like this: proc_scsi_write() <- gets id and channel from simple_strtoul() -> scsi_add_single_device() <- calls shost->transportt->user_scan() -> ata_scsi_user_scan() -> ata_find_dev() Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Patrick Lai authored
[ Upstream commit 9f169b9f ] When multiple front-ends are using the same back-end, putting state of a front-end to STOP state upon receiving pause command will result in backend stream getting released by DPCM framework unintentionally. In order to avoid backend to be released when another active front-end stream is present, put the stream state to PAUSED state instead of STOP state. Signed-off-by:
-
Satish Kharat authored
[ Upstream commit 9698b6f4 ] This fix is to avoid calling fnic_fw_reset_handler through fnic_host_reset when a finc reset is alreay in progress. Signed-off-by:
Satish Kharat <satishkh@cisco.com> Signed-off-by:
Sesidhar Baddela <sebaddel@cisco.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Jiri Kosina authored
[ Upstream commit 08f95726 ] This headlamp contains a dummy HID descriptor which pretends to be a mouse-like device, but can't be used as a mouse at all. Reported-by:
Lukas Ocilka <lukas.ocilka@suse.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Ioan-Adrian Ratiu authored
[ Upstream commit 13a6c832 ] Testing EP_FLAG_RUNNING in snd_complete_urb() before running the completion logic allows us to save a few cpu cycles by returning early, skipping the pending urb in case the stream was stopped; the stop logic handles the urb and sets the completion callbacks to NULL. Signed-off-by:
Ioan-Adrian Ratiu <adi@adirat.com> Signed-off-by:
-
Sergei Shtylyov authored
[ Upstream commit 71eae1ca ] The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25 (bits 0-15 usually used for that are occupied by the packet checksum). Thus we need to set the 'shift_rd0' field in the SH7734 SoC data... Fixes: f0e81fec ("net: sh_eth: Add support SH7734") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Mark Rutland authored
[ Upstream commit 6ef4fb38 ] Recent changes made KERN_CONT mandatory for continued lines. In the absence of KERN_CONT, a newline may be implicit inserted by the core printk code. In show_pte, we (erroneously) use printk without KERN_CONT for continued prints, resulting in output being split across a number of lines, and not matching the intended output, e.g. [ff000000000000] *pgd=00000009f511b003 , *pud=00000009f4a80003 , *pmd=0000000000000000 Fix this by using pr_cont() for all the continuations. Acked-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Arvind Yadav authored
[ Upstream commit e19f32da ] Here, pci_iomap can fail, handle this case release selected pci regions and return -ENOMEM. Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Arvind Yadav authored
[ Upstream commit 4dcd19bf ] Here, If devm_ioremap will fail. It will return NULL. Kernel can run into a NULL-pointer dereference. This error check will avoid NULL pointer dereference. Signed-off-by:
Yoichi Yuasa <yuasa@linux-mips.org> Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
[ Upstream commit 7934c98a ] Markus reported that perf segfaults when reading /sys/kernel/notes from a kernel linked with GNU gold, due to what looks like a gold bug, so do some bounds checking to avoid crashing in that case. Reported-by:
Markus Trippelsdorf <markus@trippelsdorf.de> Report-Link: http://lkml.kernel.org/r/20161219161821.GA294@x4 Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/n/tip-ryhgs6a6jxvz207j2636w31c@git.kernel.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Daniel Bristot de Oliveira authored
[ Upstream commit 07485918 ] Currently, the sched:sched_switch tracepoint reports deadline tasks with priority -1. But when reading the trace via perf script I've got the following output: # ./d & # (d is a deadline task, see [1]) # perf record -e sched:sched_switch -a sleep 1 # perf script ... swapper 0 [000] 2146.962441: sched:sched_switch: swapper/0:0 [120] R ==> d:2593 [4294967295] d 2593 [000] 2146.972472: sched:sched_switch: d:2593 [4294967295] R ==> g:2590 [4294967295] The task d reports the wrong priority [4294967295]. This happens because the "int prio" is stored in an unsigned long long val. Although it is set as a %lld, as int is shorter than unsigned long long, trace_seq_printf prints it as a positive number. The fix is just to cast the val as an int, and print it as a %d, as in the sched:sched_switch tracepoint's "format". The output with the fix is: # ./d & # perf record -e sched:sched_switch -a sleep 1 # perf script ... swapper 0 [000] 4306.374037: sched:sched_switch: swapper/0:0 [120] R ==> d:10941 [-1] d 10941 [000] 4306.383823: sched:sched_switch: d:10941 [-1] R ==> swapper/0:0 [120] [1] d.c --- #include <stdio.h> #include <unistd.h> #include <sys/syscall.h> #include <linux/types.h> #include <linux/sched.h> struct sched_attr { __u32 size, sched_policy; __u64 sched_flags; __s32 sched_nice; __u32 sched_priority; __u64 sched_runtime, sched_deadline, sched_period; }; int sched_setattr(pid_t pid, const struct sched_attr *attr, unsigned int flags) { return syscall(__NR_sched_setattr, pid, attr, flags); } int main(void) { struct sched_attr attr = { .size = sizeof(attr), .sched_policy = SCHED_DEADLINE, /* This creates a 10ms/30ms reservation */ .sched_runtime = 10 * 1000 * 1000, .sched_period = attr.sched_deadline = 30 * 1000 * 1000, }; if (sched_setattr(0, &attr, 0) < 0) { perror("sched_setattr"); return -1; } for(;;); } --- Committer notes: Got the program from the provided URL, http://bristot.me/lkml/d.c, trimmed it and included in the cset log above, so that we have everything needed to test it in one place. Signed-off-by:
Daniel Bristot de Oliveira <bristot@redhat.com> Acked-by:
Steven Rostedt <rostedt@goodmis.org> Tested-by:
-
David Lechner authored
[ Upstream commit 43aef5c2 ] This fixes an error message that was probably copied and pasted. The same message is used for both the in and out endpoints, so it makes it impossible to know which one actually failed because both cases say "IN". Make the out endpoint error message say "OUT". Signed-off-by:
David Lechner <david@lechnology.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Rafael J. Wysocki authored
[ Upstream commit c2a6bbaf ] The way acpi_find_child_device() works currently is that, if there are two (or more) devices with the same _ADR value in the same namespace scope (which is not specifically allowed by the spec and the OS behavior in that case is not defined), the first one of them found to be present (with the help of _STA) will be returned. This covers the majority of cases, but is not sufficient if some of the devices in question have a _HID (or _CID) returning some valid ACPI/PNP device IDs (which is disallowed by the spec) and the ASL writers' expectation appears to be that the OS will match devices without a valid ACPI/PNP device ID against a given bus address first. To cover this special case as well, modify find_child_checks() to prefer devices without ACPI/PNP device IDs over devices that have them. Suggested-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Krzysztof Kozlowski authored
[ Upstream commit 3ef01c96 ] NF_CT_PROTO_DCCP/SCTP/UDPLITE were switched from tristate to boolean so defconfig needs to be adjusted to silence warnings: warning: symbol value 'm' invalid for NF_CT_PROTO_DCCP warning: symbol value 'm' invalid for NF_CT_PROTO_SCTP warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
-
Moritz Fischer authored
[ Upstream commit c415f9e8 ] The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core which fixes some silicon bugs that needed software workarounds in Version 1.0 that was used on Zynq systems. Signed-off-by:
Moritz Fischer <mdf@kernel.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com> Cc: Rob Herring <robh+dt@kernel.org> Acked-by:
Sören Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by:
Michal Simek <michal.simek@xilinx.com> Signed-off-by:
-
