when compiling with allmodconfig, CONFIG_64BIT=y the file
drivers/base/regmap/regmap-mmio.c will use readq and writeq so we need
implement these functions.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

For accurate accounting call contextidr_thread_switch before a
task is scheduled, rather than after, when the 'next' variable has a
different meaning since we switched the stacks.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The ESR_EL1 decoding process is a bit cryptic, and KVM has also
a need for the same constants.

Add a new esr.h file containing the appropriate exception classes
constants, and change entry.S to use it. Fix a small bug in the
EL1 breakpoint check while we're at it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

* arm64-klib:
  arm64: klib: Optimised atomic bitops
  arm64: klib: Optimised string functions
  arm64: klib: Optimised memory functions

This patch uses the generic irqchip_init() function for initialising the
interrupt controller on arm64. It also adds several definitions required
by the ARM GIC irqchip driver but does not enable ARM_GIC yet.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

With the (re)introduction of cpu_logical_map in arm64 we switch to
the use of MPIDR values to identify CPUs. Update the psci code to
do that.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This patch implements the AArch64-specific atomic bitops functions using
exclusive memory accesses to avoid locking.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This patch introduces AArch64-specific string functions (strchr,
strrchr).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This patch introduces AArch64-specific memory functions (memcpy,
memmove, memchr, memset). These functions are not optimised for any CPU
implementation but can be used as a starting point once hardware is
available.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The reg property of the cpu nodes in the DT now contains all the
affinity levels in (MPIDR[39:32] and MPIDR[23:0]) and that's what
boot_secondary() writes in the pen, so increase the mask in
secondary_holding_pen accordingly.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

When booting the kernel, the cpu logical id map must be initialised
using device tree data passed by FW or through an embedded blob.

This patch parses the reg property in device tree "cpu" nodes,
retrieves the corresponding CPUs hardware identifiers (MPIDR) and
initialises the cpu logical map accordingly.

The device tree HW identifiers are considered valid if all CPU nodes
contain a "reg" property, there are no duplicate "reg" entries and the
DT defines a CPU node whose "reg" property defines affinity levels
that matches those of the boot CPU.

The primary CPU is assigned cpu logical number 0 to keep the current
convention valid.

Based on a0ae0240 (ARM: kernel: add
device tree init map function).
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Change the prototype of write_pen_release() accordingly and clarify
that's holding the hardware id of the secondary that's going to boot.
This is in preparation of getting HWIDs parsed from the DT.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This patch adds an arch_initcall() for the of_clk_init() clock
initialisation.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This patch adds support for using earlyprintk with 8250/16550 UART
ports. The 8250/16550 UART can either have 8-bit or 32-bit aligned
registers which is HW vendor dependent.

Kernel args for 8-bit aligned regs: earlyprintk=uart8250-8bit,<phys_address>

Kernel args for 32-bit aligned regs: earlyprintk=uart8250-32bit,<phys_address>
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Enable early_printk to use the FastModel semihosting to output
the early kernel messages. Works both for host and guest kernels.

To use this feature, pass "early_printk=smh" to the kernel.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

In order to preserve some kind of source compatibility between
arm and arm64, introduce read_cpuid_{implementor,part_number,mpidr}
which are used on KVM to find out which CPU we're running on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The Kconfig entry for DEBUG_ERRORS is a verbatim copy of the former arm
entry for that symbol. It got removed in v2.6.39 because it wasn't
actually used anywhere. There are still no users of DEBUG_ERRORS so
remove this entry too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
[catalin.marinas@arm.com: removed option from defconfig]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Config option GENERIC_HARDIRQS_NO_DEPRECATED was removed in commit
78c89825 ("genirq: Remove the now obsolete
config options and select statements"), but the select was accidentally
reintroduced in commit 8c2c3df3 ("arm64:
Build infrastructure").
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The expression to compute the padding needed to fill the uc_sigmask field
to 1024 bits actually computes the padding needed for 1080 bits.
Fortunately, due to the 16-byte alignment of the following field
(uc_mcontext) the definition in glibc contains enough bytes of padding
after uc_sigmask so that the overall offsets and size match in both
definitions.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The __atomic_hash is only defined when SMP is enabled but the
arm64ksyms.c exports it even for the UP case.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Recent clean-up of the compat signal code left an unused 'stack'
variable.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Commit 1d9d8639 ("perf,x86: fix kernel crash with PEBS/BTS after
suspend/resume") introduces a link failure since
perf_restore_debug_store() is only defined for CONFIG_CPU_SUP_INTEL:

	arch/x86/power/built-in.o: In function `restore_processor_state':
	(.text+0x45c): undefined reference to `perf_restore_debug_store'

Fix it by defining the dummy function appropriately.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 1d9d8639 ("perf,x86: fix kernel crash with PEBS/BTS after
suspend/resume") fixed a crash when doing PEBS performance profiling
after resuming, but in using init_debug_store_on_cpu() to restore the
DS_AREA mtrr it also resulted in a new WARN_ON() triggering.

init_debug_store_on_cpu() uses "wrmsr_on_cpu()", which in turn uses CPU
cross-calls to do the MSR update.  Which is not really valid at the
early resume stage, and the warning is quite reasonable.  Now, it all
happens to _work_, for the simple reason that smp_call_function_single()
ends up just doing the call directly on the CPU when the CPU number
matches, but we really should just do the wrmsr() directly instead.

This duplicates the wrmsr() logic, but hopefully we can just remove the
wrmsr_on_cpu() version eventually.
Reported-and-tested-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull btrfs fixes from Chris Mason:
 "Eric's rcu barrier patch fixes a long standing problem with our
  unmount code hanging on to devices in workqueue helpers.  Liu Bo
  nailed down a difficult assertion for in-memory extent mappings."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix warning of free_extent_map
  Btrfs: fix warning when creating snapshots
  Btrfs: return as soon as possible when edquot happens
  Btrfs: return EIO if we have extent tree corruption
  btrfs: use rcu_barrier() to wait for bdev puts at unmount
  Btrfs: remove btrfs_try_spin_lock
  Btrfs: get better concurrency for snapshot-aware defrag work

Users report that an extent map's list is still linked when it's actually
going to be freed from cache.

The story is that

a) when we're going to drop an extent map and may split this large one into
smaller ems, and if this large one is flagged as EXTENT_FLAG_LOGGING which means
that it's on the list to be logged, then the smaller ems split from it will also
be flagged as EXTENT_FLAG_LOGGING, and this is _not_ expected.

b) we'll keep ems from unlinking the list and freeing when they are flagged with
EXTENT_FLAG_LOGGING, because the log code holds one reference.

The end result is the warning, but the truth is that we set the flag
EXTENT_FLAG_LOGGING only during fsync.

So clear flag EXTENT_FLAG_LOGGING for extent maps split from a large one.
Reported-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Reported-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

Pull kbuild fix from Michal Marek:
 "One fix for for make headers_install/headers_check to not require make
  3.81.  The requirement has been accidentally introduced in 3.7."

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kbuild: fix make headers_check with make 3.80

Pull OpenRISC bug fixes from Jonas Bonn:

 - The GPIO descriptor work has exposed how broken the non-GPIOLIB bits
   for OpenRISC were.  We now require GPIOLIB as this is the preferred
   way forward.

 - The system.h split introduced a bug in llist.h for arches using
   asm-generic/cmpxchg.h directly, which is currently only OpenRISC.
   The patch here moves two defines from asm-generic/atomic.h to
   asm-generic/cmpxchg.h to make things work as they should.

 - The VIRT_TO_BUS selector was added for OpenRISC, but OpenRISC does
   not have the virt_to_bus methods, so there's a patch to remove it
   again.

* tag 'for-3.9-rc3' of git://openrisc.net/jonas/linux:
  openrisc: remove HAVE_VIRT_TO_BUS
  asm-generic: move cmpxchg*_local defs to cmpxchg.h
  openrisc: require gpiolib

Pull char/misc fixes from Greg Kroah-Hartman:
 "Here are some tiny fixes for the w1 drivers and the final removal
  patch for getting rid of CONFIG_EXPERIMENTAL (all users of it are now
  gone from your tree, this just drops the Kconfig item itself.)

  All have been in the linux-next tree for a while"

* tag 'char-misc-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  final removal of CONFIG_EXPERIMENTAL
  w1: fix oops when w1_search is called from netlink connector
  w1-gpio: fix unused variable warning
  w1-gpio: remove erroneous __exit and __exit_p()
  ARM: w1-gpio: fix erroneous gpio requests

Pull sound fixes from Takashi Iwai:
 "A collection of small fixes, as expected for the middle rc:
   - A couple of fixes for potential NULL dereferences and out-of-range
     array accesses revealed by static code parsers
   - A fix for the wrong error handling detected by trinity
   - A regression fix for missing audio on some MacBooks
   - CA0132 DSP loader fixes
   - Fix for EAPD control of IDT codecs on machines w/o speaker
   - Fix a regression in the HD-audio widget list parser code
   - Workaround for the NuForce UDH-100 USB audio"

* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix missing EAPD/GPIO setup for Cirrus codecs
  sound: sequencer: cap array index in seq_chn_common_event()
  ALSA: hda/ca0132 - Remove extra setting of dsp_state.
  ALSA: hda/ca0132 - Check download state of DSP.
  ALSA: hda/ca0132 - Check if dspload_image succeeded.
  ALSA: hda - Disable IDT eapd_switch if there are no internal speakers
  ALSA: hda - Fix snd_hda_get_num_raw_conns() to return a correct value
  ALSA: usb-audio: add a workaround for the NuForce UDH-100
  ALSA: asihpi - fix potential NULL pointer dereference
  ALSA: seq: Fix missing error handling in snd_seq_timer_open()

Pull DMA-mapping fix from Marek Szyprowski:
 "An important fix for all ARM architectures which use ZONE_DMA.
  Without it dma_alloc_* calls with GFP_ATOMIC flag might have allocated
  buffers outsize DMA zone."

* 'fixes-for-3.9' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
  ARM: DMA-mapping: add missing GFP_DMA flag for atomic buffer allocation

Pull MFD fixes from Samuel Ortiz:
 "This is the first batch of MFD fixes for 3.9.

  With this one we have:

   - An ab8500 build failure fix.
   - An ab8500 device tree parsing fix.
   - A fix for twl4030_madc remove routine to work properly (when
     built-in).
   - A fix for properly registering palmas interrupt handler.
   - A fix for omap-usb init routine to actually write into the
     hostconfig register.
   - A couple of warning fixes for ab8500-gpadc and tps65912"

* tag 'mfd-fixes-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes:
  mfd: twl4030-madc: Remove __exit_p annotation
  mfd: ab8500: Kill "reg" property from binding
  mfd: ab8500-gpadc: Complain if we fail to enable vtvout LDO
  mfd: wm831x: Don't forward declare enum wm831x_auxadc
  mfd: twl4030-audio: Fix argument type for twl4030_audio_disable_resource()
  mfd: tps65912: Declare and use tps65912_irq_exit()
  mfd: palmas: Provide irq flags through DT/platform data
  mfd: Make AB8500_CORE select POWER_SUPPLY to fix build error
  mfd: omap-usb-host: Actually update hostconfig

Pull hwmon fixes from Guenter Roeck:
 "Bug fixes for pmbus, ltc2978, and lineage-pem drivers

  Added specific maintainer for some hwmon drivers"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (pmbus/ltc2978) Fix temperature reporting
  hwmon: (pmbus) Fix krealloc() misuse in pmbus_add_attribute()
  hwmon: (lineage-pem) Add missing terminating entry for pem_[input|fan]_attributes
  MAINTAINERS: Add maintainer for MAX6697, INA209, and INA2XX drivers

This patch fixes a kernel crash when using precise sampling (PEBS)
after a suspend/resume. Turns out the CPU notifier code is not invoked
on CPU0 (BP). Therefore, the DS_AREA (used by PEBS) is not restored properly
by the kernel and keeps it power-on/resume value of 0 causing any PEBS
measurement to crash when running on CPU0.

The workaround is to add a hook in the actual resume code to restore
the DS Area MSR value. It is invoked for all CPUS. So for all but CPU0,
the DS_AREA will be restored twice but this is harmless.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

During the transition to the generic parser, the hook to the codec
specific automute function was forgotten.  This resulted in the silent
output on some MacBooks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

"chn" here is a number between 0 and 255, but ->chn_info[] only has
16 elements so there is a potential write beyond the end of the
array.

If the seq_mode isn't SEQ_2 then we let the individual drivers
(either opl3.c or midi_synth.c) handle it.  Those functions all
do a bounds check on "chn" so I haven't changed anything here.
The opl3.c driver has up to 18 channels and not 16.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

4740f73f "mfd: remove use of __devexit" removed the __devexit annotation
on the twl4030_madc_remove function, but left an __exit_p() present on the
pointer to this function. Using __exit_p was as wrong with the devexit in
place as it is now, but now we get a gcc warning about an unused function.

In order for the twl4030_madc_remove to work correctly in built-in code, we
have to remove the __exit_p.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

spec->dsp_state is initialized to DSP_DOWNLOAD_INIT, no need to reset
and check it in ca0132_download_dsp().
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Instead of using the dspload_is_loaded() function, check the dsp_state
that is kept in the spec.  The dspload_is_loaded() function returns
true if the DSP transfer was never started.  This false-positive leads
to multiple second delays when ca0132_setup_efaults() times out on
each write.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

If dspload_image() fails, it was ignored and dspload_wait_loaded() was
still called.  dsp_loaded should never be set to true in this case,
skip it.  The check in dspload_wait_loaded() return true if the DSP is
loaded or if it never started.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>