- 26 Sep, 2006 40 commits
-
-
Alan Cox authored
Again depends on the PCIAGP_FAIL patch for a define. Someone with more card knowledge should look at the ALIMAGIK case and whether latency can be safely to set to 0xA or so. Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@infradead.org>
-
Alan Cox authored
We should be doing this on all devices doing PCI<->PCI DMA. We only set the _FAIL ones when the DMA will fail or may cause crashes. This relies on the PCIAGP_FAIL patch I sent to Andrew already Signed-off-by:
-
Oliver Endriss authored
Implement fix suggested by Michael Hunold for a bug reported by Philipp Matthias Hahn: Starting "kdetv" on a Siemens DVB-C 1.x produced an oops because kdetv opened "/dev/vbi0". Remove the V4L2_CAP_VBI_CAPTURE flag because it does not work with this type of hardware anyway. Signed-off-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
-
Oliver Endriss authored
Do not select FW_LOADER unless it is really required. Signed-off-by:
-
Michal Majchrowicz authored
Add card support for Proteus Pro 2309, based on saa7130 bridge Signed-off-by:
Michal Majchrowicz <mmajchrowicz@gmail.com> Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Sascha Hauer authored
Do not return -EINVAL for index=0 in VIDIOC_ENUMSTD, because it is a valid index Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
-
Sascha Hauer authored
The vivi.current_norm field is not initialized in vivi.c, so a VIDIOC_G_STD ioctl without a prior call to VIDIOC_S_STD gives unpredictable results. mplayer does exactly this. Signed-off-by Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: -
Mauro Carvalho Chehab authored
Also sends the proper saa71111 init table. Signed-off-by: -
Cedric Le Goater authored
Replaced kernel_thread() with kthread_run() since kernel_thread() is deprecated in drivers/modules. Removed the completion and the wait queue which are now useless with kthread. Also removed the allow_signal() call as signals don't apply to kernel threads. Fixed a small race condition when thread is stopped. Please check if the timer vs. thread still works fine without the wait queue. Signed-off-by:
Cedric Le Goater <clg@fr.ibm.com> Signed-off-by:
-
Sascha Hauer authored
This patch fixes a copy-paste bug in videodev.c where the vidioc_qbuf() function gets called for the dqbuf ioctl. Signed-off-by:
-
Jose Alberto Reguero authored
While converting the configuration for the old DiB3000MC-module to the new one a wrong AGC configuration was introduced. This is using the old one again. Signed-off-by:
Jose Alberto Reguero <jareguero@telefonica.net> Signed-off-by:
Patrick Boettcher <pb@linuxtv.org> Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Alistair Buxton authored
There seems to be an off by one error in the dibusb-mb.c which causes the "Artec T1 with AN2235" box to be detected as a totally different box - but it only happens if the Artec is one with the correct USB IDs. A patch is attached to the second post. However, even with this patch, the box still won't tune. It will tune using a 2.6.12 kernel though. Signed-off-by:
Alistair Buxton <a.j.buxton@gmail.com> Signed-off-by:
-
Allan Third authored
Attached is a patch against latest HG which adds remote control support to the DigiTV driver. It works for me; Signed-off-by:
Allan Third <allan.third@gmail.com> Signed-off-by:
-
Ricardo Cerqueira authored
saa7134-alsa now unmutes/mutes the line when opening/closing the capture device, and needs this symbol Signed-off-by:
Ricardo Cerqueira <v4l@cerqueira.org> Signed-off-by:
-
Ricardo Cerqueira authored
This patch should enable unmuting the audio device when opening it (and posterior muting when closing it), doing away with the need for unmute ioctls or v4lctl usage. Signed-off-by:
-
Andrew de Quincey authored
I've just determined that module-init-tools >=3.2 is needed for dvb_attach to work. This adds a comment to Kconfig about it. Signed-off-by:
Andrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by:
-
Andrew de Quincey authored
I had forgotten to add the wrapper round the tua6100_attach function if its disabled in Kconfig Signed-off-by:
-
Mauro Carvalho Chehab authored
Software I2C were using a very conservative value of udelay=16, meaning about 20Kbps. According with Philips I2C datasheet, the i2c should answer well for times at the order of 4.7 us. So, using udelay=5 should work for all devices. After this patch, the speed should be close to 66,67 Kbps, with the current kernel software bitbang, with 30/60 duty cycle. Anyway, added a new parameter (i2c_udelay) that would allow using conservative values, if eventually a hardware doesn't support the datasheet values. Thanks to Jean Delvare <khali@linux-fr.org> for pointing this improvement. Signed-off-by: -
Mauro Carvalho Chehab authored
Updates feature-removal-schedule.txt to reflect the current scheduled date to convert all V4L1 drivers to V4L2. Signed-off-by: -
Andrew de Quincey authored
Port budget-av to use the new tua6100 driver Signed-off-by:
-
Andrew de Quincey authored
This driver was originally in budget-av.c, however I have extracted it into a seperate file to permit reuse. I also reworked the code to make it maintainable. I then examined the KNC1 windows drivers and rewrote the code in order to configure the PLL as they do. This solves a lot of reported tuning problems. Signed-off-by:
-
Mike Isely authored
Fix broken build when 24XXX support is not selected. This is required due to the requirement of removing 24XXX ifdef's from the driver source. Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Bradley Kite authored
The cx22702 returns an 8 bit unshifted value for signal strength; this is inconsistent with most other frontends Signed-off-by:
Bradley Derek Kite <bradley.kite@gmail.com> Signed-off-by:
-
Bas Bloemsaat authored
Trivial patch to make Compro PS39U WebCam work with linux by using the vicam driver. The camera is just a vicam with another USB ID, so I added that ID to the driver, and it works now. Signed-off-by:
Bas Bloemsaat <bas.bloemsaat@gmail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Mike Isely authored
The pvrusb2 driver resolution limits are now programmed the following way, based on empirical measurements of the hardware: Vertical max: 480 for NTSC, 576 otherwise Vertical min: 75 for 24xxx, 17 otherwise Horizontal max: 720 Horizontal min: 720 for 24xxx, 19 otherwise Signed-off-by:
-
Mike Isely authored
This repairs a problem introduced by a commit earlier applied. Thanks-to: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Mike Isely authored
Support for 24xxx devices was previously explicitly bracketed with CONFIG_VIDEO_PVRUSB2_24XXX inside the code because we didn't trust the stability of these changes. We trust it now; so there's no reason to leave this out of the driver anymore. Signed-off-by:
-
Mike Isely authored
Signed-off-by:
-
Mauro Carvalho Chehab authored
Scaling were not working fine; Some reserved registers were wrong; On some situations, saa7115 were not properly being initializated. Removed some duplicated code. Thanks-to: Hans Verkuil <hverkuil@xs4all.nl> for co-working on this patch. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Hans Verkuil authored
The VIDIOC_G_SLICED_VBI_CAP needs to receive the v4l2_buf_type field before it can return a result. Hence this ioctl must be IOWR, not IOR. Since this ioctl is still marked experimental we can make this change. Signed-off-by:
-
Hans Verkuil authored
Acked-by:
-
Hans Verkuil authored
Signed-off-by:
-
Mauro Carvalho Chehab authored
Without the breaks, saa7115 were not initializing PLL2. Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Unai Uribarri authored
This patch fixes the physical address and takes into account recent changes in the USB input subsystem. Acked-by:
Dmitry Torokhov <dtor@mail.ru> Signed-off-by:
Unai Uribarri <unaiur@gmail.com> Signed-off-by:
Trent Piepho <xyzzy@speakeasy.org> Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
saa7115 module is capable of calculating the proper FIR tables. However, there were 4 hardcoded tables for the standard resolution. Signed-off-by:
-
