- 26 Sep, 2006 40 commits
-
-
Clemens Ladisch authored
To prevent the emulated RTC timer from stopping when interrupts are delayed for too long, disable interrupts around all of the register initialization, and check that the interrupt handler did not schedule the next interrupt in the past. Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: Andi Kleen <ak@muc.de> Cc: Vojtech Pavlik <vojtech@suse.cz> Cc: Robert Picco <Robert.Picco@hp.com> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Haavard Skinnemoen authored
FRegister a platform device for the AT49BV6416 NOR flash chip on the ATSTK1000 development board for use by the physmap MTD driver. The SMC timings are set up before the platform device is registered so that no board-specific mapping driver is necessary. Signed-off-by:
Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by:
-
Haavard Skinnemoen authored
This patchset adds the necessary drivers and infrastructure to access the external flash on the ATSTK1000 board through the MTD subsystem. With this stuff in place, it will be possible to use a jffs2 filesystem stored in the external flash as a root filesystem. It might also be possible to update the boot loader if you drop the write protection of partition 0. As suggested by David Woodhouse, I reworked the patches to use the physmap driver instead of introducing a separate mapping driver for the ATSTK1000. I've also cleaned up the hsmc header by removing useless comments and converting spaces to tabs (my headerfile generator needs some work.) Unfortunately, I couldn't unlock the flash in fixup_use_atmel_lock because the erase regions hadn't been set up yet, so I had to do it from cfi_amdstd_setup instead. This patch: This adds a simple API for configuring the static memory controller along with an implementation for the Atmel HSMC. Signed-off-by:
-
Haavard Skinnemoen authored
This adds support for the Atmel AVR32 architecture as well as the AT32AP7000 CPU and the AT32STK1000 development board. AVR32 is a new high-performance 32-bit RISC microprocessor core, designed for cost-sensitive embedded applications, with particular emphasis on low power consumption and high code density. The AVR32 architecture is not binary compatible with earlier 8-bit AVR architectures. The AVR32 architecture, including the instruction set, is described by the AVR32 Architecture Manual, available from http://www.atmel.com/dyn/resources/prod_documents/doc32000.pdf The Atmel AT32AP7000 is the first CPU implementing the AVR32 architecture. It features a 7-stage pipeline, 16KB instruction and data caches and a full Memory Management Unit. It also comes with a large set of integrated peripherals, many of which are shared with the AT91 ARM-based controllers from Atmel. Full data sheet is available from http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf while the CPU core implementation including caches and MMU is documented by the AVR32 AP Technical Reference, available from http://www.atmel.com/dyn/resources/prod_documents/doc32001.pdf Information about the AT32STK1000 development board can be found at http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3918 including a BSP CD image with an earlier version of this patch, development tools (binaries and source/patches) and a root filesystem image suitable for booting from SD card. Alternatively, there's a preliminary "getting started" guide available at http://avr32linux.org/twiki/bin/view/Main/GettingStarted which provides links to the sources and patches you will need in order to set up a cross-compiling environment for avr32-linux. This patch, as well as the other patches included with the BSP and the toolchain patches, is actively supported by Atmel Corporation. [dmccr@us.ibm.com: Fix more pxx_page macro locations] [bunk@stusta.de: fix `make defconfig'] Signed-off-by:
Adrian Bunk <bunk@stusta.de> Signed-off-by:
Dave McCracken <dmccr@us.ibm.com> Signed-off-by:
-
Ralf Baechle authored
The third argument of au1xxx_dbdma_chan_alloc's callback function is not used anywhere. Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Cc: David Howells <dhowells@redhat.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by:
-
David Howells authored
Optimise ffs(x) by using fls(x & x - 1) which we optimise to use the SCAN instruction. Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
David Howells authored
Implement fls64() for FRV without recource to conditional jumps. Signed-off-by:
-
David Howells authored
Fix FRV fls() to handle bit 31 being set correctly (it should return 32 not 0). Signed-off-by:
-
David Howells authored
Permit __do_IRQ() to be dispensed with based on a configuration option. Signed-off-by:
-
David Howells authored
Improve FRV's use of generic IRQ handling: (*) Use generic_handle_irq() rather than __do_IRQ() as the latter is obsolete. (*) Don't implement enable() and disable() ops as these will fall back to using unmask() and mask(). (*) Provide mask_ack() functions to avoid a call each to mask() and ack(). (*) Make the cascade handlers always return IRQ_HANDLED. (*) Implement the mask() and unmask() functions in the same order as they're listed in the ops table. Signed-off-by: -
David Howells authored
Make the FRV arch use the generic IRQ code rather than having its own routines for doing so. Signed-off-by:
-
Andrew Morton authored
As David Howells <dhowells@redhat.com> points out, binfmt_elf sometimes uses off_t, sometimes uses loff_t. Use loff_t throughout. Signed-off-by:
-
Stephen Smalley authored
Take tty_mutex when accessing ->signal->tty in selinux code. Noted by Alan Cox. Longer term, we are looking at refactoring the code to provide better encapsulation of the tty layer, but this is a simple fix that addresses the immediate bug. Signed-off-by:
Stephen Smalley <sds@tycho.nsa.gov> Acked-by:
Alan Cox <alan@redhat.com> Acked-by:
James Morris <jmorris@namei.org> Signed-off-by:
-
Eric Paris authored
This patch converts the semaphore in the superblock security struct to a mutex. No locking changes or other code changes are done. Signed-off-by:
Eric Paris <eparis@redhat.com> Acked-by:
-
Eric Paris authored
This patch converts the remaining isec->sem into a mutex. Very similar locking is provided as before only in the faster smaller mutex rather than a semaphore. An out_unlock path is introduced rather than the conditional unlocking found in the original code. Signed-off-by:
-
Eric Paris authored
inode_security_set_sid is only called by security_inode_init_security, which is called when a new file is being created and needs to have its incore security state initialized and its security xattr set. This helper used to be called in other places in the past, but now only has the one. So this patch rolls inode_security_set_sid directly back into security_inode_init_security. There also is no need to hold the isec->sem while doing this, as the inode is not available to other threads at this point in time. Signed-off-by:
-
Darrel Goeddel authored
Introduces support for policy version 21. This version of the binary kernel policy allows for defining range transitions on security classes other than the process security class. As always, backwards compatibility for older formats is retained. The security class is read in as specified when using the new format, while the "process" security class is assumed when using an older policy format. Signed-off-by:
Darrel Goeddel <dgoeddel@trustedcs.com> Signed-off-by:
-
Stephen Smalley authored
Enable configuration of SELinux maximum supported policy version to support legacy userland (init) that does not gracefully handle kernels that support newer policy versions two or more beyond the installed policy, as in FC3 and FC4. [bunk@stusta.de: improve Kconfig help text] Signed-off-by:
-
Stephen Smalley authored
Replace ctxid with sid in selinux_audit_rule_match interface for consistency with other interfaces. Signed-off-by:
-
Stephen Smalley authored
Rename selinux_ctxid_to_string to selinux_sid_to_string to be consistent with other interfaces. Signed-off-by:
-
Stephen Smalley authored
Eliminate selinux_task_ctxid since it duplicates selinux_task_get_sid. Signed-off-by:
-
Christoph Lameter authored
There are many places where we need to determine the node of a zone. Currently we use a difficult to read sequence of pointer dereferencing. Put that into an inline function and use throughout VM. Maybe we can find a way to optimize the lookup in the future. Signed-off-by:
Christoph Lameter <clameter@sgi.com> Signed-off-by:
-
Christoph Lameter authored
I found two location in hugetlb.c where we chase pointer instead of using page_to_nid(). Page_to_nid is more effective and can get the node directly from page flags. Signed-off-by:
-
Ram Gupta authored
Update the comments for __oom_kill_task() to reflect the code changes. Signed-off-by:
Ram Gupta <r.gupta@astronautics.com> Signed-off-by:
-
Christoph Lameter authored
Minor performance fix. If we reclaimed enough slab pages from a zone then we can avoid going off node with the current allocation. Take care of updating nr_reclaimed when reclaiming from the slab. Signed-off-by:
-
Christoph Lameter authored
Currently one can enable slab reclaim by setting an explicit option in /proc/sys/vm/zone_reclaim_mode. Slab reclaim is then used as a final option if the freeing of unmapped file backed pages is not enough to free enough pages to allow a local allocation. However, that means that the slab can grow excessively and that most memory of a node may be used by slabs. We have had a case where a machine with 46GB of memory was using 40-42GB for slab. Zone reclaim was effective in dealing with pagecache pages. However, slab reclaim was only done during global reclaim (which is a bit rare on NUMA systems). This patch implements slab reclaim during zone reclaim. Zone reclaim occurs if there is a danger of an off node allocation. At that point we 1. Shrink the per node page cache if the number of pagecache pages is more than min_unmapped_ratio percent of pages in a zone. 2. Shrink the slab cache if the number of the nodes reclaimable slab pages (patch depends on earlier one that implements that counter) are more than min_slab_ratio (a new /proc/sys/vm tunable). The shrinking of the slab cache is a bit problematic since it is not node specific. So we simply calculate what point in the slab we want to reach (current per node slab use minus the number of pages that neeed to be allocated) and then repeately run the global reclaim until that is unsuccessful or we have reached the limit. I hope we will have zone based slab reclaim at some point which will make that easier. The default for the min_slab_ratio is 5% Also remove the slab option from /proc/sys/vm/zone_reclaim_mode. [akpm@osdl.org: cleanups] Signed-off-by:
-
Christoph Lameter authored
Remove the atomic counter for slab_reclaim_pages and replace the counter and NR_SLAB with two ZVC counter that account for unreclaimable and reclaimable slab pages: NR_SLAB_RECLAIMABLE and NR_SLAB_UNRECLAIMABLE. Change the check in vmscan.c to refer to to NR_SLAB_RECLAIMABLE. The intend seems to be to check for slab pages that could be freed. Signed-off-by:
-
Christoph Lameter authored
*_pages is a better description of the role of the variable. Signed-off-by:
-
Christoph Lameter authored
The allocpercpu functions __alloc_percpu and __free_percpu() are heavily using the slab allocator. However, they are conceptually slab. This also simplifies SLOB (at this point slob may be broken in mm. This should fix it). Signed-off-by:
-
Christoph Lameter authored
If a zone is unpopulated then we do not need to check for pages that are to be drained and also not for vm counters that may need to be updated. Signed-off-by:
-
Christoph Lameter authored
Free one_page currently adds the page to a fake list and calls free_page_bulk. Fee_page_bulk takes it off again and then calles __free_one_page. Make free_one_page go directly to __free_one_page. Saves list on / off and a temporary list in free_one_page for higher ordered pages. Signed-off-by:
-
Dave McCracken authored
One of the changes necessary for shared page tables is to standardize the pxx_page macros. pte_page and pmd_page have always returned the struct page associated with their entry, while pte_page_kernel and pmd_page_kernel have returned the kernel virtual address. pud_page and pgd_page, on the other hand, return the kernel virtual address. Shared page tables needs pud_page and pgd_page to return the actual page structures. There are very few actual users of these functions, so it is simple to standardize their usage. Since this is basic cleanup, I am submitting these changes as a standalone patch. Per Hugh Dickins' comments about it, I am also changing the pxx_page_kernel macros to pxx_page_vaddr to clarify their meaning. Signed-off-by:
-
Siddha, Suresh B authored
On High end systems (1024 or so cpus) this can potentially cause stack overflow. Fix the stack usage. Signed-off-by:
Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by:
-
Christoph Lameter authored
In many places we will need to use the same combination of flags. Specify a single GFP_THISNODE definition for ease of use in gfp.h. Signed-off-by:
-
Christoph Lameter authored
Profiling really suffers with off node buffers. Fail if no memory is available on the nodes. The profiling code can deal with these failures should they occur. Signed-off-by:
-
Christoph Lameter authored
There are frequent references to *z in get_page_from_freelist. Add an explicit zone variable that can be used in all these places. Signed-off-by:
-
Christoph Lameter authored
The uncached allocator manages per node pools. Specify __GFP_THISNODE in order to force allocation on the indicated node or fail. The uncached allocator has already logic to deal with failing allocations. Signed-off-by:
-
Christoph Lameter authored
If the user specified a node where we should move the page to then we really do not want any other node. Signed-off-by:
-
Christoph Lameter authored
[PATCH] Add __GFP_THISNODE to avoid fallback to other nodes and ignore cpuset/memory policy restrictions Add a new gfp flag __GFP_THISNODE to avoid fallback to other nodes. This flag is essential if a kernel component requires memory to be located on a certain node. It will be needed for alloc_pages_node() to force allocation on the indicated node and for alloc_pages() to force allocation on the current node. Signed-off-by:
-
Ravikiran G Thirumalai authored
Place the alien array cache locks of on slab malloc slab caches on a seperate lockdep class. This avoids false positives from lockdep [akpm@osdl.org: build fix] Signed-off-by:
Ravikiran Thirumalai <kiran@scalex86.org> Signed-off-by:
Shai Fultheim <shai@scalex86.org> Cc: Thomas Gleixner <tglx@linutronix.de> Acked-by:
Arjan van de Ven <arjan@linux.intel.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Christoph Lameter <clameter@engr.sgi.com> Signed-off-by:
-
