Toggling of C-tag VLAN filter should not affect the "any S-tag" steering rule.

Fixes: 8a271746 ("net/mlx5e: Receive s-tagged packets in promiscuous mode")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Use the correct formatting for netdev features.

Fixes: 0e405443 ("net/mlx5e: Improve set features ndo resiliency")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Encap entries cached by the driver could be invalidated due to
tunnel destination neighbour state changes.
When attempting to offload a flow that uses a cached encap entry,
we must check the entry validity and defer the offloading
if the entry exists but not valid.

When EAGAIN is returned, the flow offloading to hardware takes place
by the neigh update code when the tunnel destination neighbour
becomes connected.

Fixes: 232c0013 ("net/mlx5e: Add support to neighbour update flow")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When offloading header re-write, the HW may need to adjust checksums along
the packet. For IP traffic, and a case where we are asked to modify fields in
the IP header, current HW supports that only for TCP and UDP. Enforce it, in
this case fail the offloading attempt for non TCP/UDP packets.

Fixes: d7e75a32 ('net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions')
Fixes: 2f4fe4ca ('net/mlx5e: Add offloading of NIC TC pedit (header re-write) actions')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In case the neighbour for the tunnel destination isn't valid,
we send a neighbour update request but we free the encap
header buffer. This is wrong, because we still need it for
allocating a HW encap entry once the neighbour is available.

Fix that by skipping freeing it if we wait for neighbour.

Fixes: 232c0013 ('net/mlx5e: Add support to neighbour update flow')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Added check for the maximal number of flow counters attached
to rule (FTE).

Fixes: bd5251db ('net/mlx5_core: Introduce flow steering destination of type counter')
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently, FPGA capability is located in (mdev)->caps.hca_cur,
change the location to be (mdev)->caps.fpga,
since hca_cur is reserved for HCA device capabilities.

Fixes: e29341fb ("net/mlx5: FPGA, Add basic support for Innova")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When cleaning rdma netdevice we need to save the mdev pointer
because priv is released when we release netdev.

This bug was found using the kernel address sanitizer (KASAN).
use-after-free in mlx5_rdma_netdev_free+0xe3/0x100 [mlx5_core]

Fixes: 48935bbb ("net/mlx5e: IPoIB, Add netdevice profile skeleton")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The sctp_for_each_transport() function takes an pointer to int.  The
cb->args[] array holds longs so it's only using the high 32 bits.  It
works on little endian system but will break on big endian 64 bit
machines.

Fixes: d25adbeb ("sctp: fix an use-after-free issue in sctp_sock_dump")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2017-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.14

Quite a lot of fixes this time. Most notable is the brcmfmac fix for a
CVE issue.

iwlwifi

* a couple of bugzilla bugs related to multicast handling

* two fixes for WoWLAN bugs that were causing queue hangs and
  re-initialization problems

* two fixes for potential uninitialized variable use reported by Dan
  Carpenter in relation to a recently introduced patch

* a fix for buffer reordering in the newly supported 9000 device
  family

* fix a race when starting aggregation

* small fix for a recent patch to wake mac80211 queues

* send non-bufferable management frames in the generic queue so they
  are not sent on queues that are under power-save

ath10k

* fix a PCI PM related gcc warning

brcmfmac

* CVE-2017-0786: add length check scan results from firmware

* respect passive scan requests from user space

qtnfmac

* fix race in tx path when using multiple interfaces

* cancel ongoing scan when removing the wireless interface
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
aquantia: Atlantic driver bugfixes und improvements

This series contains bugfixes for aQuantia Atlantic driver.

Changes in v2:
Review comments applied:
- min_mtu set removed
- extra mtu range check is removed
- err codes handling improved
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Call skb_frag_dma_map multiple times if tx length is greater than
device max and avoid processing tx ring until entire packet has been
sent.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to a bug in aquantia atlantic card firmware, it sometimes reports
invalid link speed bits. That caused driver to report link down events,
although link itself is totally fine.

This patch ignores such out of blue readings.
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver did a poor job in managing its Tx queues: Sometimes it could stop
tx queues due to link down condition in aq_nic_xmit - but never waked up
them. That led to Tx path total suspend.
This patch fixes this and improves generic queue management:
- introduces queue restart counter
- uses generic netif_ interface to disable and enable tx path
- refactors link up/down condition and introduces dmesg log event when
  link changes.
- introduces new constant for minimum descriptors count required for queue
  wakeup
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Although hardware is capable for almost 16K MTU, without max_mtu field
correctly set it only allows standard MTU to be used.
This patch enables max MTU, calculating it from hardware maximum frame size
of 16352 octets (including FCS).

Fixes: 5513e164 ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we try to delete the same tunnel twice, the first delete operation
does a lookup (l2tp_tunnel_get), finds the tunnel, calls
l2tp_tunnel_delete, which queues it for deletion by
l2tp_tunnel_del_work.

The second delete operation also finds the tunnel and calls
l2tp_tunnel_delete. If the workqueue has already fired and started
running l2tp_tunnel_del_work, then l2tp_tunnel_delete will queue the
same tunnel a second time, and try to free the socket again.

Add a dead flag to prevent firing the workqueue twice. Then we can
remove the check of queue_work's result that was meant to prevent that
race but doesn't.

Reproducer:

    ip l2tp add tunnel tunnel_id 3000 peer_tunnel_id 4000 local 192.168.0.2 remote 192.168.0.1 encap udp udp_sport 5000 udp_dport 6000
    ip l2tp add session name l2tp1 tunnel_id 3000 session_id 1000 peer_session_id 2000
    ip link set l2tp1 up
    ip l2tp del tunnel tunnel_id 3000
    ip l2tp del tunnel tunnel_id 3000

Fixes: f8ccac0e ("l2tp: put tunnel socket release on a workqueue")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running LTP IPsec tests, KASan might report:

BUG: KASAN: use-after-free in vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
Read of size 4 at addr ffff880dc6ad1980 by task swapper/0/0
...
Call Trace:
  <IRQ>
  dump_stack+0x63/0x89
  print_address_description+0x7c/0x290
  kasan_report+0x28d/0x370
  ? vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
  __asan_report_load4_noabort+0x19/0x20
  vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
  ? vti_init_net+0x190/0x190 [ip_vti]
  ? save_stack_trace+0x1b/0x20
  ? save_stack+0x46/0xd0
  dev_hard_start_xmit+0x147/0x510
  ? icmp_echo.part.24+0x1f0/0x210
  __dev_queue_xmit+0x1394/0x1c60
...
Freed by task 0:
  save_stack_trace+0x1b/0x20
  save_stack+0x46/0xd0
  kasan_slab_free+0x70/0xc0
  kmem_cache_free+0x81/0x1e0
  kfree_skbmem+0xb1/0xe0
  kfree_skb+0x75/0x170
  kfree_skb_list+0x3e/0x60
  __dev_queue_xmit+0x1298/0x1c60
  dev_queue_xmit+0x10/0x20
  neigh_resolve_output+0x3a8/0x740
  ip_finish_output2+0x5c0/0xe70
  ip_finish_output+0x4ba/0x680
  ip_output+0x1c1/0x3a0
  xfrm_output_resume+0xc65/0x13d0
  xfrm_output+0x1e4/0x380
  xfrm4_output_finish+0x5c/0x70

Can be fixed if we get skb->len before dst_output().

Fixes: b9959fd3 ("vti: switch to new ip tunnel code")
Fixes: 22e1b23d ("vti6: Support inter address family tunneling.")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_KASAN is enabled, the "--param asan-stack=1" causes rather large
stack frames in some functions. This goes unnoticed normally because
CONFIG_FRAME_WARN is disabled with CONFIG_KASAN by default as of commit
3f181b4d ("lib/Kconfig.debug: disable -Wframe-larger-than warnings with
KASAN=y").

The kernelci.org build bot however has the warning enabled and that led
me to investigate it a little further, as every build produces these warnings:

net/wireless/nl80211.c:4389:1: warning: the frame size of 2240 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/wireless/nl80211.c:1895:1: warning: the frame size of 3776 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/wireless/nl80211.c:1410:1: warning: the frame size of 2208 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/bridge/br_netlink.c:1282:1: warning: the frame size of 2544 bytes is larger than 2048 bytes [-Wframe-larger-than=]

Most of this problem is now solved in gcc-8, which can consolidate
the stack slots for the inline function arguments. On older compilers
we can add a workaround by declaring a local variable in each function
to pass the inline function argument.

Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Inlining these functions creates lots of stack variables that each take
64 bytes when KASAN is enabled, leading to this warning about potential
stack overflow:

drivers/net/ethernet/rocker/rocker_ofdpa.c: In function 'ofdpa_cmd_flow_tbl_add':
drivers/net/ethernet/rocker/rocker_ofdpa.c:621:1: error: the frame size of 2752 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]

gcc-8 can now consolidate the stack slots itself, but on older versions
we get the same behavior by using a temporary variable that holds a
copy of the inline function argument.

Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When mapping the RX DMA buffers, the driver was accidentally specifying
zero for the buffer length.  Under normal circumstances, SWIOTLB does not
need to allocate a bounce buffer, so the address is just mapped without
checking the size field.  This is why the error was not detected earlier.

Fixes: b9b17deb ("net: emac: emac gigabit ethernet controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Guillaume Nault says:

====================
l2tp: fix some races in session deletion

L2TP provides several interfaces for deleting sessions. Using two of
them concurrently can lead to use-after-free bugs.

Patch #2 uses a flag to prevent double removal of L2TP sessions.
Patch #1 fixes a bug found in the way. Fixing this bug is also
necessary for patch #2 to handle all cases.

This issue is similar to the tunnel deletion bug being worked on by
Sabrina: https://patchwork.ozlabs.org/patch/814173/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There are several ways to remove L2TP sessions:

  * deleting a session explicitly using the netlink interface (with
    L2TP_CMD_SESSION_DELETE),
  * deleting the session's parent tunnel (either by closing the
    tunnel's file descriptor or using the netlink interface),
  * closing the PPPOL2TP file descriptor of a PPP pseudo-wire.

In some cases, when these methods are used concurrently on the same
session, the session can be removed twice, leading to use-after-free
bugs.

This patch adds a 'dead' flag, used by l2tp_session_delete() and
l2tp_tunnel_closeall() to prevent them from stepping on each other's
toes.

The session deletion path used when closing a PPPOL2TP file descriptor
doesn't need to be adapted. It already has to ensure that a session
remains valid for the lifetime of its PPPOL2TP file descriptor.
So it takes an extra reference on the session in the ->session_close()
callback (pppol2tp_session_close()), which is eventually dropped
in the ->sk_destruct() callback of the PPPOL2TP socket
(pppol2tp_session_destruct()).
Still, __l2tp_session_unhash() and l2tp_session_queue_purge() can be
called twice and even concurrently for a given session, but thanks to
proper locking and re-initialisation of list fields, this is not an
issue.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

If l2tp_tunnel_delete() or l2tp_tunnel_closeall() deletes a session
right after pppol2tp_release() orphaned its socket, then the 'sock'
variable of the pppol2tp_session_close() callback is NULL. Yet the
session is still used by pppol2tp_release().

Therefore we need to take an extra reference in any case, to prevent
l2tp_tunnel_delete() or l2tp_tunnel_closeall() from freeing the session.

Since the pppol2tp_session_close() callback is only set if the session
is associated to a PPPOL2TP socket and that both l2tp_tunnel_delete()
and l2tp_tunnel_closeall() hold the PPPOL2TP socket before calling
pppol2tp_session_close(), we're sure that pppol2tp_session_close() and
pppol2tp_session_destruct() are paired and called in the right order.
So the reference taken by the former will be released by the later.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

ath.git fixes for 4.14. Major changes:

ath10k

* fix a PCI PM related gcc warning

Xiaolong reported a suspicious rcu_dereference_check in the device
unregister notifier callback. Since we do not dereference the
rx_handler_data, it's ok to just check for the value of the pointer.
Note that this section is already protected by rtnl_lock.

[  101.364846] WARNING: suspicious RCU usage
[  101.365654] 4.13.0-rc6-01701-gceed73a2 #1 Not tainted
[  101.370873] -----------------------------
[  101.372472] drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c:57 suspicious rcu_dereference_check() usage!
[  101.374427]
[  101.374427] other info that might help us debug this:
[  101.374427]
[  101.387491]
[  101.387491] rcu_scheduler_active = 2, debug_locks = 1
[  101.389368] 1 lock held by trinity-main/2809:
[  101.390736]  #0:  (rtnl_mutex){+.+.+.}, at: [<8146085b>] rtnl_lock+0xf/0x11
[  101.395482]
[  101.395482] stack backtrace:
[  101.396948] CPU: 0 PID: 2809 Comm: trinity-main Not tainted 4.13.0-rc6-01701-gceed73a2 #1
[  101.398857] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-20161025_171302-gandalf 04/01/2014
[  101.401079] Call Trace:
[  101.401656]  dump_stack+0xa1/0xeb
[  101.402871]  lockdep_rcu_suspicious+0xc7/0xd0
[  101.403665]  rmnet_is_real_dev_registered+0x40/0x4e
[  101.405199]  rmnet_config_notify_cb+0x2c/0x142
[  101.406344]  ? wireless_nlevent_flush+0x47/0x71
[  101.407385]  notifier_call_chain+0x2d/0x47
[  101.408645]  raw_notifier_call_chain+0xc/0xe
[  101.409882]  call_netdevice_notifiers_info+0x41/0x49
[  101.411402]  call_netdevice_notifiers+0xc/0xe
[  101.412713]  rollback_registered_many+0x268/0x36e
[  101.413702]  rollback_registered+0x39/0x56
[  101.414965]  unregister_netdevice_queue+0x79/0x88
[  101.415908]  unregister_netdev+0x16/0x1d

Fixes: ceed73a2 ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All the error handling paths 'goto error', except this one.
We should also go to error in this case, or some resources will be
leaking.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull parisc fixes from Helge Deller:

 - Unbreak parisc bootloader by avoiding a gcc-7 optimization to convert
   multiple byte-accesses into one word-access.

 - Add missing HWPOISON page fault handler code. I completely missed
   that when I added HWPOISON support during this merge window and it
   only showed up now with the madvise07 LTP test case.

 - Fix backtrace unwinding to stop when stack start has been reached.

 - Issue warning if initrd has been loaded into memory regions with
   broken RAM modules.

 - Fix HPMC handler (parisc hardware fault handler) to comply with
   architecture specification.

 - Avoid compiler warnings about too large frame sizes.

 - Minor init-section fixes.

* 'parisc-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Unbreak bootloader due to gcc-7 optimizations
  parisc: Reintroduce option to gzip-compress the kernel
  parisc: Add HWPOISON page fault handler code
  parisc: Move init_per_cpu() into init section
  parisc: Check if initrd was loaded into broken RAM
  parisc: Add PDCE_CHECK instruction to HPMC handler
  parisc: Add wrapper for pdc_instr() firmware function
  parisc: Move start_parisc() into init section
  parisc: Stop unwinding at start of stack
  parisc: Fix too large frame size warnings

Pull rdma fixes from Doug Ledford:

 - Smattering of miscellanous fixes

 - A five patch series for i40iw that had a patch (5/5) that was larger
   than I would like, but I took it because it's needed for large scale
   users

 - An 8 patch series for bnxt_re that landed right as I was leaving on
   PTO and so had to wait until now...they are all appropriate fixes for
   -rc IMO

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (22 commits)
  bnxt_re: Don't issue cmd to delete GID for QP1 GID entry before the QP is destroyed
  bnxt_re: Fix memory leak in FRMR path
  bnxt_re: Remove RTNL lock dependency in bnxt_re_query_port
  bnxt_re: Fix race between the netdev register and unregister events
  bnxt_re: Free up devices in module_exit path
  bnxt_re: Fix compare and swap atomic operands
  bnxt_re: Stop issuing further cmds to FW once a cmd times out
  bnxt_re: Fix update of qplib_qp.mtu when modified
  i40iw: Add support for port reuse on active side connections
  i40iw: Add missing VLAN priority
  i40iw: Call i40iw_cm_disconn on modify QP to disconnect
  i40iw: Prevent multiple netdev event notifier registrations
  i40iw: Fail open if there are no available MSI-X vectors
  RDMA/vmw_pvrdma: Fix reporting correct opcodes for completion
  IB/bnxt_re: Fix frame stack compilation warning
  IB/mlx5: fix debugfs cleanup
  IB/ocrdma: fix incorrect fall-through on switch statement
  IB/ipoib: Suppress the retry related completion errors
  iw_cxgb4: remove the stid on listen create failure
  iw_cxgb4: drop listen destroy replies if no ep found
  ...

Pull networking fixes from David Miller:

 1) Fix NAPI poll list corruption in enic driver, from Christian
    Lamparter.

 2) Fix route use after free, from Eric Dumazet.

 3) Fix regression in reuseaddr handling, from Josef Bacik.

 4) Assert the size of control messages in compat handling since we copy
    it in from userspace twice. From Meng Xu.

 5) SMC layer bug fixes (missing RCU locking, bad refcounting, etc.)
    from Ursula Braun.

 6) Fix races in AF_PACKET fanout handling, from Willem de Bruijn.

 7) Don't use ARRAY_SIZE on spinlock array which might have zero
    entries, from Geert Uytterhoeven.

 8) Fix miscomputation of checksum in ipv6 udp code, from Subash Abhinov
    Kasiviswanathan.

 9) Push the ipv6 header properly in ipv6 GRE tunnel driver, from Xin
    Long.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
  inet: fix improper empty comparison
  net: use inet6_rcv_saddr to compare sockets
  net: set tb->fast_sk_family
  net: orphan frags on stand-alone ptype in dev_queue_xmit_nit
  MAINTAINERS: update git tree locations for ieee802154 subsystem
  net: prevent dst uses after free
  net: phy: Fix truncation of large IRQ numbers in phy_attached_print()
  net/smc: no close wait in case of process shut down
  net/smc: introduce a delay
  net/smc: terminate link group if out-of-sync is received
  net/smc: longer delay for client link group removal
  net/smc: adapt send request completion notification
  net/smc: adjust net_device refcount
  net/smc: take RCU read lock for routing cache lookup
  net/smc: add receive timeout check
  net/smc: add missing dev_put
  net: stmmac: Cocci spatch "of_table"
  lan78xx: Use default values loaded from EEPROM/OTP after reset
  lan78xx: Allow EEPROM write for less than MAX_EEPROM_SIZE
  lan78xx: Fix for eeprom read/write when device auto suspend
  ...

Merge tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor

Pull apparmor updates from John Johansen:
 "This is the apparmor pull request, similar to SELinux and seccomp.

  It's the same series that I was sent to James' security tree + one
  regression fix that was found after the series was sent to James and
  would have been sent for v4.14-rc2.

  Features:
  - in preparation for secid mapping add support for absolute root view
    based labels
  - add base infastructure for socket mediation
  - add mount mediation
  - add signal mediation

  minor cleanups and changes:
  - be defensive, ensure unconfined profiles have dfas initialized
  - add more debug asserts to apparmorfs
  - enable policy unpacking to audit different reasons for failure
  - cleanup conditional check for label in label_print
  - Redundant condition: prev_ns. in [label.c:1498]

  Bug Fixes:
  - fix regression in apparmorfs DAC access permissions
  - fix build failure on sparc caused by undeclared signals
  - fix sparse report of incorrect type assignment when freeing label proxies
  - fix race condition in null profile creation
  - Fix an error code in aafs_create()
  - Fix logical error in verify_header()
  - Fix shadowed local variable in unpack_trans_table()"

* tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
  apparmor: fix apparmorfs DAC access permissions
  apparmor: fix build failure on sparc caused by undeclared signals
  apparmor: fix incorrect type assignment when freeing proxies
  apparmor: ensure unconfined profiles have dfas initialized
  apparmor: fix race condition in null profile creation
  apparmor: move new_null_profile to after profile lookup fns()
  apparmor: add base infastructure for socket mediation
  apparmor: add more debug asserts to apparmorfs
  apparmor: make policy_unpack able to audit different info messages
  apparmor: add support for absolute root view based labels
  apparmor: cleanup conditional check for label in label_print
  apparmor: add mount mediation
  apparmor: add the ability to mediate signals
  apparmor: Redundant condition: prev_ns. in [label.c:1498]
  apparmor: Fix an error code in aafs_create()
  apparmor: Fix logical error in verify_header()
  apparmor: Fix shadowed local variable in unpack_trans_table()

Pull ACPI fixes from Rafael Wysocki:
 "These fix the initialization of resources in the ACPI WDAT watchdog
  driver, a recent regression in the ACPI device properties handling, a
  recent change in behavior causing the ACPI_HANDLE() macro to only work
  for GPL code and create a MAINTAINERS entry for ACPI PMIC drivers in
  order to specify the official reviewers for that code.

  Specifics:

   - Fix the initialization of resources in the ACPI WDAT watchdog
     driver that uses unititialized memory which causes compiler
     warnings to be triggered (Arnd Bergmann).

   - Fix a recent regression in the ACPI device properties handling that
     causes some device properties data to be skipped during enumeration
     (Sakari Ailus).

   - Fix a recent change in behavior that caused the ACPI_HANDLE() macro
     to stop working for non-GPL code which is a problem for the NVidia
     binary graphics driver, for example (John Hubbard).

   - Add a MAINTAINERS entry for the ACPI PMIC drivers to specify the
     official reviewers for that code (Rafael Wysocki)"

* tag 'acpi-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: properties: Return _DSD hierarchical extension (data) sub-nodes correctly
  ACPI / bus: Make ACPI_HANDLE() work for non-GPL code again
  ACPI / watchdog: properly initialize resources
  ACPI / PMIC: Add code reviewers to MAINTAINERS

Josef Bacik says:

====================
net: fix reuseaddr regression

I introduced a regression when reworking the fastreuse port stuff that allows
bind conflicts to occur once a reuseaddr successfully opens on an existing tb.
The root cause is I reversed an if statement which caused us to set the tb as if
there were no owners on the socket if there were, which obviously is not
correct.

Dave could you please queue these changes up for -stable, I've run them through
the net tests and added another test to check for this problem specifically.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When doing my reuseport rework I screwed up and changed a

if (hlist_empty(&tb->owners))

to

if (!hlist_empty(&tb->owners))

This is obviously bad as all of the reuseport/reuse logic was reversed,
which caused weird problems like allowing an ipv4 bind conflict if we
opened an ipv4 only socket on a port followed by an ipv6 only socket on
the same port.

Fixes: b9470c27 ("inet: kill smallest_size and smallest_port")
Reported-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ipv6_rcv_saddr_equal() we need to use inet6_rcv_saddr(sk) for the
ipv6 compare with the fast socket information to make sure we're doing
the proper comparisons.

Fixes: 637bc8bb ("inet: reset tb->fastreuseport when adding a reuseport sk")
Reported-and-tested-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to set the tb->fast_sk_family properly so we can use the proper
comparison function for all subsequent reuseport bind requests.

Fixes: 637bc8bb ("inet: reset tb->fastreuseport when adding a reuseport sk")
Reported-and-tested-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Zerocopy skbs frags are copied when the skb is looped to a local sock.
Commit 1080e512 ("net: orphan frags on receive") introduced calls
to skb_orphan_frags to deliver_skb and __netif_receive_skb for this.

With msg_zerocopy, these skbs can also exist in the tx path and thus
loop from dev_queue_xmit_nit. This already calls deliver_skb in its
loop. But it does not orphan before a separate pt_prev->func().

Add the missing skb_orphan_frags_rx.

Changes
  v1->v2: handle skb_orphan_frags_rx failure

Fixes: 1f8b977a ("sock: enable MSG_ZEROCOPY")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull power management fixes from Rafael Wysocki:
 "These fix a cpufreq regression introduced by recent changes related to
  the generic DT driver, an initialization time memory leak in cpuidle
  on ARM, a PM core bug that may cause system suspend/resume to fail on
  some systems, a request type validation issue in the PM QoS framework
  and two documentation-related issues.

  Specifics:

   - Fix a regression in cpufreq on systems using DT as the source of
     CPU configuration information where two different code paths
     attempt to create the cpufreq-dt device object (there can be only
     one) and fix up the "compatible" matching for some TI platforms on
     top of that (Viresh Kumar, Dave Gerlach).

   - Fix an initialization time memory leak in cpuidle on ARM which
     occurs if the cpuidle driver initialization fails (Stefan Wahren).

   - Fix a PM core function that checks whether or not there are any
     system suspend/resume callbacks for a device, but forgets to check
     legacy callbacks which then may be skipped incorrectly and the
     system may crash and/or the device may become unusable after a
     suspend-resume cycle (Rafael Wysocki).

   - Fix request type validation for latency tolerance PM QoS requests
     which may lead to unexpected behavior (Jan Schönherr).

   - Fix a broken link to PM documentation from a header file and a typo
     in a PM document (Geert Uytterhoeven, Rafael Wysocki)"

* tag 'pm-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: ti-cpufreq: Support additional am43xx platforms
  ARM: cpuidle: Avoid memleak if init fail
  cpufreq: dt-platdev: Add some missing platforms to the blacklist
  PM: core: Fix device_pm_check_callbacks()
  PM: docs: Drop an excess character from devices.rst
  PM / QoS: Use the correct variable to check the QoS request type
  driver core: Fix link to device power management documentation

Pull input fixes from Dmitry Torokhov:

 - fixes for two long standing issues (lock up and a crash) in force
   feedback handling in uinput driver

 - tweak to firmware update timing in Elan I2C touchpad driver.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elan_i2c - extend Flash-Write delay
  Input: uinput - avoid crash when sending FF request to device going away
  Input: uinput - avoid FF flush when destroying device

Pull seccomp updates from Kees Cook:
 "Major additions:

   - sysctl and seccomp operation to discover available actions
     (tyhicks)

   - new per-filter configurable logging infrastructure and sysctl
     (tyhicks)

   - SECCOMP_RET_LOG to log allowed syscalls (tyhicks)

   - SECCOMP_RET_KILL_PROCESS as the new strictest possible action

   - self-tests for new behaviors"

[ This is the seccomp part of the security pull request during the merge
  window that was nixed due to unrelated problems   - Linus ]

* tag 'seccomp-v4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  samples: Unrename SECCOMP_RET_KILL
  selftests/seccomp: Test thread vs process killing
  seccomp: Implement SECCOMP_RET_KILL_PROCESS action
  seccomp: Introduce SECCOMP_RET_KILL_PROCESS
  seccomp: Rename SECCOMP_RET_KILL to SECCOMP_RET_KILL_THREAD
  seccomp: Action to log before allowing
  seccomp: Filter flag to log all actions except SECCOMP_RET_ALLOW
  seccomp: Selftest for detection of filter flag support
  seccomp: Sysctl to configure actions that are allowed to be logged
  seccomp: Operation for checking if an action is available
  seccomp: Sysctl to display available actions
  seccomp: Provide matching filter for introspection
  selftests/seccomp: Refactor RET_ERRNO tests
  selftests/seccomp: Add simple seccomp overhead benchmark
  selftests/seccomp: Add tests for basic ptrace actions

Merge tag '4.14-smb3-fixes-from-recent-test-events-for-stable' of git://git.samba.org/sfrench/cifs-2.6

Pull cifs fixes from Steve French:
 "Various SMB3 fixes for stable and security improvements from the
  recently completed SMB3/Samba test events

* tag '4.14-smb3-fixes-from-recent-test-events-for-stable' of git://git.samba.org/sfrench/cifs-2.6:
  SMB3: Don't ignore O_SYNC/O_DSYNC and O_DIRECT flags
  SMB3: handle new statx fields
  SMB: Validate negotiate (to protect against downgrade) even if signing off
  cifs: release auth_key.response for reconnect.
  cifs: release cifs root_cred after exit_cifs
  CIFS: make arrays static const, reduces object code size
  [SMB3] Update session and share information displayed for debugging SMB2/SMB3
  cifs: show 'soft' in the mount options for hard mounts
  SMB3: Warn user if trying to sign connection that authenticated as guest
  SMB3: Fix endian warning
  Fix SMB3.1.1 guest authentication to Samba