- 22 Mar, 2013 21 commits
-
-
Linus Torvalds authored
Merge misc fixes from Andrew Morton. * emailed patches from Andrew Morton <akpm@linux-foundation.org>: mqueue: sys_mq_open: do not call mnt_drop_write() if read-only mm/hotplug: only free wait_table if it's allocated by vmalloc dma-debug: update DMA debug API to better handle multiple mappings of a buffer dma-debug: fix locking bug in check_unmap() drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap() drivers/rtc/rtc-da9052.c: fix for rtc device registration mm: zone_end_pfn is too small poweroff: change orderly_poweroff() to use schedule_work() mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting printk: Provide a wake_up_klogd() off-case irq_work.h: fix warning when CONFIG_IRQ_WORK=n
-
Vladimir Davydov authored
mnt_drop_write() must be called only if mnt_want_write() succeeded, otherwise the mnt_writers counter will diverge. mnt_writers counters are used to check if remounting FS as read-only is OK, so after an extra mnt_drop_write() call, it would be impossible to remount mqueue FS as read-only. Besides, on umount a warning would be printed like this one: ===================================== [ BUG: bad unlock balance detected! ] 3.9.0-rc3 #5 Not tainted ------------------------------------- a.out/12486 is trying to release lock (sb_writers) at: mnt_drop_write+0x1f/0x30 but there are no more locks to release! Signed-off-by:
Vladimir Davydov <vdavydov@parallels.com> Cc: Doug Ledford <dledford@redhat.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Jianguo Wu authored
zone->wait_table may be allocated from bootmem, it can not be freed. Signed-off-by:
Jianguo Wu <wujianguo@huawei.com> Reviewed-by:
Tang Chen <tangchen@cn.fujitsu.com> Cc: Tang Chen <tangchen@cn.fujitsu.com> Cc: Jiang Liu <jiang.liu@huawei.com> Signed-off-by:
-
Alexander Duyck authored
There were reports of the igb driver unmapping buffers without calling dma_mapping_error. On closer inspection issues were found in the DMA debug API and how it handled multiple mappings of the same buffer. The issue I found is the fact that the debug_dma_mapping_error would only set the map_err_type to MAP_ERR_CHECKED in the case that the was only one match for device and device address. However in the case of non-IOMMU, multiple addresses existed and as a result it was not setting this field once a second mapping was instantiated. I have resolved this by changing the search so that it instead will now set MAP_ERR_CHECKED on the first buffer that matches the device and DMA address that is currently in the state MAP_ERR_NOT_CHECKED. A secondary side effect of this patch is that in the case of multiple buffers using the same address only the last mapping will have a valid map_err_type. The previous mappings will all end up with map_err_type set to MAP_ERR_CHECKED because of the dma_mapping_error call in debug_dma_map_page. However this behavior may be preferable as it means you will likely only see one real error per multi-mapped buffer, versus the current behavior of multiple false errors mer multi-mapped buffer. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Cc: Joerg Roedel <joro@8bytes.org> Reviewed-by:
Shuah Khan <shuah.khan@hp.com> Tested-by:
-
Alexander Duyck authored
In check_unmap() it is possible to get into a dead-locked state if dma_mapping_error is called. The problem is that the bucket is locked in check_unmap, and locked again by debug_dma_mapping_error which is called by dma_mapping_error. To resolve that we must release the lock on the bucket before making the call to dma_mapping_error. [akpm@linux-foundation.org: restore 80-col trickery to be consistent with the rest of the file] Signed-off-by:
-
Nicolas Ferre authored
On some revisions of AT91 SoCs, the RTC IMR register is not working. Instead of elaborating a workaround for that specific SoC or IP version, we simply use a software variable to store the Interrupt Mask Register and modify it for each enabling/disabling of an interrupt. The overhead of this is negligible anyway. The interrupt mask register (IMR) for the RTC is broken on the AT91SAM9x5 sub-family of SoCs (good overview of the members here: http://www.eewiki.net/display/linuxonarm/AT91SAM9x5 ). The "user visible effect" is the RTC doesn't work. That sub-family is less than two years old and only has devicetree (DT) support and came online circa lk 3.7 . The dust is yet to settle on the DT stuff at least for AT91 SoCs (translation: lots of stuff is still broken, so much that it is hard to know where to start). The fix in the patch is pretty simple: just shadow the silicon IMR register with a variable in the driver. Some older SoCs (pre-DT) use the the rtc-at91rm9200 driver (e.g. obviously the AT91RM9200) and they should not be impacted by the change. There shouldn't be a large volume of interrupts associated with a RTC. Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Reported-by:
Douglas Gilbert <dgilbert@interlog.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
H Hartley Sweeten authored
Commit be867814 ("drivers/video/ep93xx-fb.c: use devm_ functions") introduced a build error: drivers/video/ep93xx-fb.c: In function 'ep93xxfb_probe': drivers/video/ep93xx-fb.c:532: error: implicit declaration of function 'devm_ioremap' drivers/video/ep93xx-fb.c:533: warning: assignment makes pointer from integer without a cast Include <linux/io.h> to pickup the declaration of 'devm_ioremap'. Signed-off-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Acked-by:
Ryan Mallon <rmallon@gmail.com> Cc: Damien Cassou <damien.cassou@lifl.fr> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Ashish Jangam authored
Add support for the virtual irq since now MFD only handles virtual irq Without this patch rtc device will fail in registration. (akpm: Ashish has a different version whcih will be needed for 3.8.x and earlier kernels) Signed-off-by:
Ashish <ashish.jangam@kpitcummins.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Russ Anderson authored
Booting with 32 TBytes memory hits BUG at mm/page_alloc.c:552! (output below). The key hint is "page 4294967296 outside zone". 4294967296 = 0x100000000 (bit 32 is set). The problem is in include/linux/mmzone.h: 530 static inline unsigned zone_end_pfn(const struct zone *zone) 531 { 532 return zone->zone_start_pfn + zone->spanned_pages; 533 } zone_end_pfn is "unsigned" (32 bits). Changing it to "unsigned long" (64 bits) fixes the problem. zone_end_pfn() was added recently in commit 108bcc96 ("mm: add & use zone_end_pfn() and zone_spans_pfn()") Output from the failure. No AGP bridge found page 4294967296 outside zone [ 4294967296 - 4327469056 ] ------------[ cut here ]------------ kernel BUG at mm/page_alloc.c:552! invalid opcode: 0000 [#1] SMP Modules linked in: CPU 0 Pid: 0, comm: swapper Not tainted 3.9.0-rc2.dtp+ #10 RIP: free_one_page+0x382/0x430 Process swapper (pid: 0, threadinfo ffffffff81942000, task ffffffff81955420) Call Trace: __free_pages_ok+0x96/0xb0 __free_pages+0x25/0x50 __free_pages_bootmem+0x8a/0x8c __free_memory_core+0xea/0x131 free_low_memory_core_early+0x4a/0x98 free_all_bootmem+0x45/0x47 mem_init+0x7b/0x14c start_kernel+0x216/0x433 x86_64_start_reservations+0x2a/0x2c x86_64_start_kernel+0x144/0x153 Code: 89 f1 ba 01 00 00 00 31 f6 d3 e2 4c 89 ef e8 66 a4 01 00 e9 2c fe ff ff 0f 0b eb fe 0f 0b 66 66 2e 0f 1f 84 00 00 00 00 00 eb f3 <0f> 0b eb fe 0f 0b 0f 1f 84 00 00 00 00 00 eb f6 0f 0b eb fe 49 Signed-off-by:Russ Anderson <rja@sgi.com> Reported-by:
George Beshers <gbeshers@sgi.com> Acked-by:
Hedi Berriche <hedi@sgi.com> Cc: Cody P Schafer <cody@linux.vnet.ibm.com> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by:
-
Oleg Nesterov authored
David said: Commit 6c0c0d4d ("poweroff: fix bug in orderly_poweroff()") apparently fixes one bug in orderly_poweroff(), but introduces another. The comments on orderly_poweroff() claim it can be called from any context - and indeed we call it from interrupt context in arch/powerpc/platforms/pseries/ras.c for example. But since that commit this is no longer safe, since call_usermodehelper_fns() is not safe in interrupt context without the UMH_NO_WAIT option. orderly_poweroff() can be used from any context but UMH_WAIT_EXEC is sleepable. Move the "force" logic into __orderly_poweroff() and change orderly_poweroff() to use the global poweroff_work which simply calls __orderly_poweroff(). While at it, remove the unneeded "int argc" and change argv_split() to use GFP_KERNEL. We use the global "bool poweroff_force" to pass the argument, this can obviously affect the previous request if it is pending/running. So we only allow the "false => true" transition assuming that the pending "true" should succeed anyway. If schedule_work() fails after that we know that work->func() was not called yet, it must see the new value. This means that orderly_poweroff() becomes async even if we do not run the command and always succeeds, schedule_work() can only fail if the work is already pending. We can export __orderly_poweroff() and change the non-atomic callers which want the old semantics. Signed-off-by:Oleg Nesterov <oleg@redhat.com> Reported-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Reported-by:
David Gibson <david@gibson.dropbear.id.au> Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi> Cc: Feng Hong <hongfeng@marvell.com> Cc: Kees Cook <keescook@chromium.org> Cc: Serge Hallyn <serge.hallyn@canonical.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by:
-
Wanpeng Li authored
hugetlb_total_pages is used for overcommit calculations but the current implementation considers only the default hugetlb page size (which is either the first defined hugepage size or the one specified by default_hugepagesz kernel boot parameter). If the system is configured for more than one hugepage size, which is possible since commit a137e1cc ("hugetlbfs: per mount huge page sizes") then the overcommit estimation done by __vm_enough_memory() (resp. shown by meminfo_proc_show) is not precise - there is an impression of more available/allowed memory. This can lead to an unexpected ENOMEM/EFAULT resp. SIGSEGV when memory is accounted. Testcase: boot: hugepagesz=1G hugepages=1 the default overcommit ratio is 50 before patch: egrep 'CommitLimit' /proc/meminfo CommitLimit: 55434168 kB after patch: egrep 'CommitLimit' /proc/meminfo CommitLimit: 54909880 kB [akpm@linux-foundation.org: coding-style tweak] Signed-off-by:
Wanpeng Li <liwanp@linux.vnet.ibm.com> Acked-by:
Michal Hocko <mhocko@suse.cz> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Hillf Danton <dhillf@gmail.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: <stable@vger.kernel.org> [3.0+] Signed-off-by:
-
Frederic Weisbecker authored
wake_up_klogd() is useless when CONFIG_PRINTK=n because neither printk() nor printk_sched() are in use and there are actually no waiter on log_wait waitqueue. It should be a stub in this case for users like bust_spinlocks(). Otherwise this results in this warning when CONFIG_PRINTK=n and CONFIG_IRQ_WORK=n: kernel/built-in.o In function `wake_up_klogd': (.text.wake_up_klogd+0xb4): undefined reference to `irq_work_queue' To fix this, provide an off-case for wake_up_klogd() when CONFIG_PRINTK=n. There is much more from console_unlock() and other console related code in printk.c that should be moved under CONFIG_PRINTK. But for now, focus on a minimal fix as we passed the merged window already. [akpm@linux-foundation.org: include printk.h in bust_spinlocks.c] Signed-off-by:
Frederic Weisbecker <fweisbec@gmail.com> Reported-by:
James Hogan <james.hogan@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
James Hogan authored
A randconfig caught repeated compiler warnings when CONFIG_IRQ_WORK=n due to the definition of a non-inline static function in <linux/irq_work.h>: include/linux/irq_work.h +40 : warning: 'irq_work_needs_cpu' defined but not used Make it inline to supress the warning. This is caused commit 00b42959 ("irq_work: Don't stop the tick with pending works") merged in v3.9-rc1. Signed-off-by:
-
git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds authored
Pull KVM fix from Marcelo Tosatti: "Fix compilation on PPC with !CONFIG_KVM" * git://git.kernel.org/pub/scm/virt/kvm/kvm: Revert "KVM: allow host header to be included even for !CONFIG_KVM"
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usbLinus Torvalds authored
Pull USB fixes from Greg Kroah-Hartman: "Here are a number of USB fixes that resolve issues that have been reported against 3.9-rc3." * tag 'usb-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (37 commits) USB: ti_usb_3410_5052: fix use-after-free in TIOCMIWAIT USB: ssu100: fix use-after-free in TIOCMIWAIT USB: spcp8x5: fix use-after-free in TIOCMIWAIT USB: quatech2: fix use-after-free in TIOCMIWAIT USB: pl2303: fix use-after-free in TIOCMIWAIT USB: oti6858: fix use-after-free in TIOCMIWAIT USB: mos7840: fix use-after-free in TIOCMIWAIT USB: mos7840: fix broken TIOCMIWAIT USB: mct_u232: fix use-after-free in TIOCMIWAIT USB: io_ti: fix use-after-free in TIOCMIWAIT USB: io_edgeport: fix use-after-free in TIOCMIWAIT USB: ftdi_sio: fix use-after-free in TIOCMIWAIT USB: f81232: fix use-after-free in TIOCMIWAIT USB: cypress_m8: fix use-after-free in TIOCMIWAIT USB: ch341: fix use-after-free in TIOCMIWAIT USB: ark3116: fix use-after-free in TIOCMIWAIT USB: serial: add modem-status-change wait queue USB: serial: fix interface refcounting USB: io_ti: fix get_icount for two port adapters USB: garmin_gps: fix memory leak on disconnect ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/soundLinus Torvalds authored
Pull sound fixes from Takashi Iwai: "Mostly HD-audio and USB-audio regression fixes: - Oops fix at unloading of snd-hda-codec-conexant module - A few trivial regression fixes for Cirrus and Conexant HD-audio codecs - Relax the USB-audio descriptor parse errors as non-fatal - Fix locking of HD-audio CA0132 DSP loader - Fix the generic HD-audio parser for VIA codecs" * tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: hda - Fix DAC assignment for independent HP ALSA: hda - Fix abuse of snd_hda_lock_devices() for DSP loader ALSA: hda - Fix typo in checking IEC958 emphasis bit ALSA: snd-usb: mixer: ignore -EINVAL in snd_usb_mixer_controls() ALSA: snd-usb: mixer: propagate errors up the call chain ALSA: usb: Parse UAC2 extension unit like for UAC1 ALSA: hda - Fix yet missing GPIO/EAPD setup in cirrus driver ALSA: hda/cirrus - Fix the digital beep registration ALSA: hda - Fix missing beep detach in patch_conexant.c ALSA: documentation: Fix typo in Documentation/sound -
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bpLinus Torvalds authored
Pull EDAC fixes from Borislav Petkov: "A fix from Mauro to correct csrow size accounting in sysfs and a sparse fix from Stephen Hemminger." * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: EDAC: Merge mci.mem_is_per_rank with mci.csbased amd64_edac: Correct DIMM sizes EDAC: Make sysfs functions static
-
Linus Torvalds authored
Dave Jones found another /proc issue with his Trinity tool: thanks to the namespace model, we can have multiple /proc dentries that point to the same inode, aliasing directories in /proc/<pid>/net/ for example. This ends up being a total disaster, because it acts like hardlinked directories, and causes locking problems. We rely on the topological sort of the inodes pointed to by dentries, and if we have aliased directories, that odering becomes unreliable. In short: don't do this. Multiple dentries with the same (directory) inode is just a bad idea, and the namespace code should never have exposed things this way. But we're kind of stuck with it. This solves things by just always allocating a new inode during /proc dentry lookup, instead of using "iget_locked()" to look up existing inodes by superblock and number. That actually simplies the code a bit, at the cost of potentially doing more inode [de]allocations. That said, the inode lookup wasn't free either (and did a lot of locking of inodes), so it is probably not that noticeable. We could easily keep the old lookup model for non-directory entries, but rather than try to be excessively clever this just implements the minimal and simplest workaround for the problem. Reported-and-tested-by:
Dave Jones <davej@redhat.com> Analyzed-by:
Al Viro <viro@zeniv.linux.org.uk> Cc: stable@vger.kernel.org Signed-off-by:
-
Marcelo Tosatti authored
This reverts commit f445f11e as it breaks PPC with CONFIG_KVM=n. Signed-off-by:
Marcelo Tosatti <mtosatti@redhat.com>
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull CIFS fixes from Steve French: "Three small CIFS Fixes (the most important of the three fixes a recent problem authenticating to Windows 8 using cifs rather than SMB2)" * 'for-next' of git://git.samba.org/sfrench/cifs-2.6: cifs: ignore everything in SPNEGO blob after mechTypes cifs: delay super block destruction until all cifsFileInfo objects are gone cifs: map NT_STATUS_SHARING_VIOLATION to EBUSY instead of ETXTBSY
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 fixes from Ted Ts'o: "Fix a number of regression and other bugs in ext4, most of which were relatively obscure cornercases or races that were found using regression tests." * tag 'ext4_for_linue' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (21 commits) ext4: fix data=journal fast mount/umount hang ext4: fix ext4_evict_inode() racing against workqueue processing code ext4: fix memory leakage in mext_check_coverage ext4: use s_extent_max_zeroout_kb value as number of kb ext4: use atomic64_t for the per-flexbg free_clusters count jbd2: fix use after free in jbd2_journal_dirty_metadata() ext4: reserve metadata block for every delayed write ext4: update reserved space after the 'correction' ext4: do not use yield() ext4: remove unused variable in ext4_free_blocks() ext4: fix WARN_ON from ext4_releasepage() ext4: fix the wrong number of the allocated blocks in ext4_split_extent() ext4: update extent status tree after an extent is zeroed out ext4: fix wrong m_len value after unwritten extent conversion ext4: add self-testing infrastructure to do a sanity check ext4: avoid a potential overflow in ext4_es_can_be_merged() ext4: invalidate extent status tree during extent migration ext4: remove unnecessary wait for extent conversion in ext4_fallocate() ext4: add warning to ext4_convert_unwritten_extents_endio ext4: disable merging of uninitialized extents ...
-
- 21 Mar, 2013 19 commits
-
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Make sure waiting processes are woken on modem-status changes. Currently processes are only woken on termios changes regardless of whether the modem status has changed. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. When switching to tty ports, some lifetime assumptions were changed. Specifically, close can now be called before the final tty reference is dropped as part of hangup at device disconnect. Even with the ftdi private-data refcounting this means that the port private data can be freed while a process is sleeping on modem-status changes and thus cannot be relied on to detect disconnects when woken up. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Also remove bogus test for private data pointer being NULL as it is never assigned in the loop. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Add modem-status-change wait queue to struct usb_serial_port that subdrivers can use to implement TIOCMIWAIT. Currently subdrivers use a private wait queue which may have been released when waking up after device disconnected. Note that we're adding a new wait queue rather than reusing the tty-port one as we do not want to get woken up at hangup (yet). Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Make sure the interface is not released before our serial device. Note that drivers are still not allowed to access the interface in any way that may interfere with another driver that may have gotten bound to the same interface after disconnect returns. Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Add missing get_icount field to two-port driver. The two-port driver was not updated when switching to the new icount interface in commit 0bca1b91 ("tty: Convert the USB drivers to the new icount interface"). Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
