This adds the ebi2 and ebi2cs groups to the MSM8660 pin control
documentation document.

Cc: devicetree@vger.kernel.org
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

After some digging around I found documentation (!) of the APQ8060
EBI2 pin groups. It turns out I first need to split the group in
two: ebi2cs and ebi2 proper. The chip select pins are kind of
orthogonal to the other EBI2 pins since CS1B and CS2B can be muxed
over address bits 7 and 6 (don't know why, but they can). This
is good to fix up before we add users.

Also found what the "holes" in the assignment all the way up to
gpio158 was actually for.

All mux documentation comes from "Snapdragon(TM) S3 APQ8060-based
DragonBoard(TM) GPIO User Guide Rev. E August 10, 2012", published
by Bsquare Corporation.

As the documentation seems a bit hard to come by I put some comments
in the group definitions so that it is clear to all readers what
is going on here and what the lines are used for.

Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Commit e2756baa ("pinctrl: imx21: make it explicitly non-modular")
missed the removal of the MODULE_DEVICE_TABLE() macro causing the
following build error:

drivers/pinctrl/freescale/pinctrl-imx21.c:328:1: error: data definition has no type or storage class [-Werror]
 MODULE_DEVICE_TABLE(of, imx21_pinctrl_of_match);

,so remove the macro to fix this problem.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In sun4/5/6/7i, all the pin function related to NAND0 controller is
named "nand0". However, in sun8i, some of the functions are named as
"nand". This patch renamed them to "nand0", for the consistency.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This SoC has no SD card controller.  Nor does it have USB port3.
These pin-mux settings have no point.

Fixes: 70f2f9c4 ("pinctrl: uniphier: add UniPhier PH1-LD11 pinctrl driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add support to mux in the second external bus interface as
follows:

- CS1 and CS2 on GPIO39 and GPIO40 as func 2
- ADDR_7 thru ADDR_0 on GPIO123 thru GPIO130 as func 1
- CS4, CS3 and CS0 on GPIO132, GPIO133, GPIO134 as func 1
- DATA_15 thru DATA_0 on GPIO135 thru GPIO150 as func 1
- OE on GPIO151 as func 1
- ADV on GPIO153 as func 1
- WE on GPIO157 as func 1

This external bus is used on the APQ8060 Dragonboard to connect
an external SMSC9211 ethernet adapter, but there are many other
usecases for the EBI2.

Cc: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The msm8974 pinctrl variant has a couple USB HSIC "glue"
registers that let us mux between the pinctrl register settings
or the HSIC core settings for the HSIC pins (gpio 144 and gpio
145). Support this method of operation by adding hsic_data and
hsic_strobe pins that can select between hsic_ctl and gpio
functions. This allows us to toggle the hsic pin configuration
over to the HSIC core at runtime.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The function selection bitfield is not always 3 bits wide.
Sometimes it is 4 bits wide. Let's use the npins struct member to
determine how many bits wide the function selection bitfield is
so we clear the correct amount of bits in the register while
remuxing the pins.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In order to support the Qualcomm MDM9615 SoC, add support for the TLMM
using the Qualcomm pinctrl generic driver.

Note: the pinctrl is partial, need Documentation to complete all the groups.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

of_find_node_by_name does an of_node_get on its return value,
so an of_node_put is needed on this value before the corresponding
variable goes out of scope.

The Coccinelle semantic patch used to make this change is as follows:
@@
struct device_node *n;
struct device_node *n1;
statement S;
identifier f;
expression E;
constant C;
@@

n = of_find_node_by_name(...)
...
if (!n) S
... when != of_node_put(n)
    when != n1 = f(n,...)
    when != E = n
    when any
    when strict
(
+ of_node_put(n);
  return -C;
|
  of_node_put(n);
|
  n1 = f(n,...)
|
  E = n
|
  return ...;
)
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the initial support of the Broadcom NSP pinmux driver.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Device tree binding documentation for Broadcom NSP IOMUX driver
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'sh-pfc-for-v4.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v4.8

  - Voltage switching support for R-Car H3,
  - DRIF pin support for R-Car H3,
  - Cleanups and fixes.

This driver adds pinctrl support for Intel Merrifield. The IP block which is
called Family-Level Interface Shim is a separate entity in SoC. The GPIO driver
(gpio-intel-mid.c) will be updated accordingly to support pinctrl interface.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_MXS
drivers/pinctrl/freescale/Kconfig:	bool

...meaning that it currently is not being built as a module by anyone.

It also doesn't have any modular functionality, so it doesn't need
module.h included at all.

What it does have is an exported function that was used as a shared
".remove" by other drivers, but those use cases (imx23 and imx28)
are now gone, and hence this can disappear as well.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX28
drivers/pinctrl/freescale/Kconfig:	bool

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX23
drivers/pinctrl/freescale/Kconfig:	bool

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_init wasn't actually used by this driver, the init
ordering remains unchanged with this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_VF610
drivers/pinctrl/freescale/Kconfig:	bool "Freescale Vybrid VF610 pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init wasn't in use by this driver, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX7D
drivers/pinctrl/freescale/Kconfig:	bool "IMX7D pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Anson Huang <Anson.Huang@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6UL
drivers/pinctrl/freescale/Kconfig:	bool "IMX6UL pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Anson Huang <Anson.Huang@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6SX
drivers/pinctrl/freescale/Kconfig:	bool "IMX6SX pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Anson Huang <Anson.Huang@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6SL
drivers/pinctrl/freescale/Kconfig:	bool "IMX6SL pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6Q
drivers/pinctrl/freescale/Kconfig:	bool "IMX6Q/DL pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We don't replace module.h with init.h since the file already has that.
But we do add export.h since this file uses the global THIS_MODULE.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6Q
drivers/pinctrl/freescale/Kconfig:	bool "IMX6Q/DL pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX53
drivers/pinctrl/freescale/Kconfig:	bool "IMX53 pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX51
drivers/pinctrl/freescale/Kconfig:	bool "IMX51 pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX50
drivers/pinctrl/freescale/Kconfig:	bool "IMX50 pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX35
drivers/pinctrl/freescale/Kconfig:	bool "IMX35 pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX27
drivers/pinctrl/freescale/Kconfig:	bool "IMX27 pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX25
drivers/pinctrl/freescale/Kconfig:        bool "IMX25 pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Denis Carikli <denis@eukrea.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX21
drivers/pinctrl/freescale/Kconfig:	bool "i.MX21 pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX1
drivers/pinctrl/freescale/Kconfig:	bool "IMX1 pinctrl driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

None of these files have anything modular in them, so they
don't need to be bringing in module.h and all its dependencies.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The pinconf-generic.h file exposes functions for creating generic mappings
but it does not expose a function for freeing the mappings. Add a function
for freeing generic mappings.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds DRIF[0-3] pinmux support for r8a7795 SoC.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Now we have PINMUX_SINGLE(). Let's use it instead of PINMUX_IPSR_NOGP()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>