[ Upstream commit cd8f76c0 ]

As soon as hardware is notified of a transmit, we no longer can assume
skb can be dereferenced, as TX completion might have freed the packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 5ff0feac ]

The newer flavors of Yukon II use a different method for receive
checksum offload. This is indicated in the driver by the SKY2_HW_NEW_LE
flag. On these newer chips, the BMU_ENA_RX_CHKSUM should not be set.

The driver would get incorrectly toggle the bit, enabling the old
checksum logic on these chips and cause a BUG_ON() assertion. If
receive checksum was toggled via ethtool.
Reported-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 4399a4df ]

Commit 081b1b1b (l2tp: fix l2tp_ip_sendmsg() route handling) added
a race, in case IP route cache is disabled.

In this case, we should not do the dst_release(&rt->dst), since it'll
free the dst immediately, instead of waiting a RCU grace period.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Chapman <jchapman@katalix.com>
Cc: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit a06998b8 ]

We must prevent module unloading if some devices are still attached to
l2tp_eth driver.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Cc: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 20e2a864 ]

When NetLabel is not enabled, e.g. CONFIG_NETLABEL=n, and the system
receives a CIPSO tagged packet it is dropped (cipso_v4_validate()
returns non-zero).  In most cases this is the correct and desired
behavior, however, in the case where we are simply forwarding the
traffic, e.g. acting as a network bridge, this becomes a problem.

This patch fixes the forwarding problem by providing the basic CIPSO
validation code directly in ip_options_compile() without the need for
the NetLabel or CIPSO code.  The new validation code can not perform
any of the CIPSO option label/value verification that
cipso_v4_validate() does, but it can verify the basic CIPSO option
format.

The behavior when NetLabel is enabled is unchanged.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit cc9b17ad ]

We need to validate the number of pages consumed by data_len, otherwise frags
array could be overflowed by userspace. So this patch validate data_len and
return -EMSGSIZE when data_len may occupies more frags than MAX_SKB_FRAGS.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 7deabca0 upstream.

We can stall RCU processing on SMP platforms if a CPU sits in its idle
loop for a long time.  This happens because we don't call irq_enter()
and irq_exit() around generic_smp_call_function_interrupt() and
friends.  Add the necessary calls, and remove the one from within
ipi_timer(), so that they're all in a common place.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 1df2ae31 upstream.

Add sanity checks when loading sparing table from disk to avoid accessing
unallocated memory or writing to it.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit adee11b2 upstream.

Check provided length of partition table so that (possibly maliciously)
corrupted partition table cannot cause accessing data beyond current buffer.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit cb14d340 upstream.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 858faa57 upstream

backported for linux-3.2.y, linux-3.3.y, linux-3.4.y

add_virtual_intf() needs to return an ERR_PTR(), instead of NULL,
on errors, otherwise cfg80211 will crash.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 71babb27 upstream.

According to Documentation/trace/ftrace.txt:

tracing_cpumask:

        This is a mask that lets the user only trace
        on specified CPUS. The format is a hex string
        representing the CPUS.

The tracing_cpumask currently doesn't affect the tracing state of
per-CPU ring buffers.

This patch enables/disables CPU recording as its corresponding bit in
tracing_cpumask is set/unset.

Link: http://lkml.kernel.org/r/1336096792-25373-3-git-send-email-vnagarnaik@google.com

Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Justin Teravest <teravest@google.com>
Cc: David Sharp <dhsharp@google.com>
Signed-off-by: Vaibhav Nagarnaik <vnagarnaik@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 6e1c39c6 upstream.

The recent fix for power-map controls (commit b0791dda) caused
regressions on some other HP laptops.  They have fixed pins but these
pins are exposed as jack-detectable.  Thus the driver tries to control
the power-map dynamically per jack detection where it never gets on.

This patch adds the check of connection and it assumes the no jack
detection is available for fixed pins no matter what pin capability
says.

BugLink: http://bugs.launchpad.net/bugs/1013183Reported-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit b0239faa upstream.

If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and memory is fragmented and a
sufficiently-large metadata device is used in a thin pool then the space
map checker will fail to allocate the memory it requires.

Switch from kmalloc to vmalloc to allow larger virtually contiguous
allocations for the space map checker's internal count arrays.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 62662303 upstream.

If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and dm_sm_checker_create()
fails, dm_tm_create_internal() would still return success even though it
cleaned up all resources it was supposed to have created.  This will
lead to a kernel crash:

general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
...
RIP: 0010:[<ffffffff81593659>]  [<ffffffff81593659>] dm_bufio_get_block_size+0x9/0x20
Call Trace:
  [<ffffffff81599bae>] dm_bm_block_size+0xe/0x10
  [<ffffffff8159b8b8>] sm_ll_init+0x78/0xd0
  [<ffffffff8159c1a6>] sm_ll_new_disk+0x16/0xa0
  [<ffffffff8159c98e>] dm_sm_disk_create+0xfe/0x160
  [<ffffffff815abf6e>] dm_pool_metadata_open+0x16e/0x6a0
  [<ffffffff815aa010>] pool_ctr+0x3f0/0x900
  [<ffffffff8158d565>] dm_table_add_target+0x195/0x450
  [<ffffffff815904c4>] table_load+0xe4/0x330
  [<ffffffff815917ea>] ctl_ioctl+0x15a/0x2c0
  [<ffffffff81591963>] dm_ctl_ioctl+0x13/0x20
  [<ffffffff8116a4f8>] do_vfs_ioctl+0x98/0x560
  [<ffffffff8116aa51>] sys_ioctl+0x91/0xa0
  [<ffffffff81869f52>] system_call_fastpath+0x16/0x1b

Fix the space map checker code to return an appropriate ERR_PTR and have
dm_sm_disk_create() and dm_tm_create_internal() check for it with
IS_ERR.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 25d7cd6f upstream.

Cleanup the shadow table before destroying the transaction manager.

Reference: leak was identified with kmemleak when running
test_discard_random_sectors in the thinp-test-suite.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 9f846a16 upstream.

Especially vesafb likes to map everything as uc- (yikes), and if that
mapping hangs around still while we try to map the gtt as wc the
kernel will downgrade our request to uc-, resulting in abyssal
performance.

Unfortunately we can't do this as early as readon does (i.e. as the
first thing we do when initializing the hw) because our fb/mmio space
region moves around on a per-gen basis. So I've had to move it below
the gtt initialization, but that seems to work, too. The important
thing is that we do this before we set up the gtt wc mapping.

Now an altogether different question is why people compile their
kernels with vesafb enabled, but I guess making things just work isn't
bad per se ...

v2:
- s/radeondrmfb/inteldrmfb/
- fix up error handling

v3: Kill #ifdef X86, this is Intel after all. Noticed by Ben Widawsky.

v4: Jani Nikula complained about the pointless bool primary
initialization.

v5: Don't oops if we can't allocate, noticed by Chris Wilson.

v6: Resolve conflicts with agp rework and fixup whitespace.

This is commit e188719a in drm-next.

Backport to 3.5 -fixes queue requested by Dave Airlie - due to grub
using vesa on fedora their initrd seems to load vesafb before loading
the real kms driver. So tons more people actually experience a
dead-slow gpu. Hence also the Cc: stable.
Reported-and-tested-by: "Kilarski, Bernard R" <bernard.r.kilarski@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 055d3747 upstream.

commit 58c54fcc
     md/raid10: handle further errors during fix_read_error better.

in 3.1 added "r10_sync_page_io" which takes an IO size in sectors.
But we were passing the IO size in bytes!!!
This resulting in bio_add_page failing, and empty request being sent
down, and a consequent BUG_ON in scsi_lib.

[fix missing space in error message at same time]

This fix is suitable for 3.1.y and later.
Reported-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 1850753d upstream.

In ops_run_io(), the call to md_wait_for_blocked_rdev will decrement
nr_pending so we lose the reference we hold on the rdev.
So atomic_inc it first to maintain the reference.

This bug was introduced by commit  73e92e51
    md/raid5.  Don't write to known bad block on doubtful devices.

which appeared in 3.0, so patch is suitable for stable kernels since
then.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 6c0544e2 upstream.

In chunk_aligned_read() we are adding data_offset before calling
is_badblock.  But is_badblock also adds data_offset, so that is bad.

So move the addition of data_offset to after the call to
is_badblock.

This bug was introduced by commit 31c176ec
     md/raid5: avoid reading from known bad blocks.
which first appeared in 3.0.  So that patch is suitable for any
-stable kernel from 3.0.y onwards.  However it will need minor
revision for most of those (as the comment didn't appear until
recently).
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
[bwh: Backported to 3.2: ignored missing comment]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit fc448a18 upstream.

If a RAID10 has an odd number of chunks - as might happen when there
are an odd number of devices - the last chunk has no pair and so is
not mirrored.  We don't store data there, but when recovering the last
device in an array we retry to recover that last chunk from a
non-existent location.  This results in an error, and the recovery
aborts.

When we get to that last chunk we should just stop - there is nothing
more to do anyway.

This bug has been present since the introduction of RAID10, so the
patch is appropriate for any -stable kernel.
Reported-by: Christian Balzer <chibi@gol.com>
Tested-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2f584a14 upstream.

Since we are taking a registers, this should never have been an sldi.
Talking to paulus offline, this is the correct fix.

Was introduced by:
 commit 19ccb76a
 Author: Paul Mackerras <paulus@samba.org>
 Date:   Sat Jul 23 17:42:46 2011 +1000

Talking to paulus, this shouldn't be a literal.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit bc1d7702 upstream.

We have a bug report where the kernel hits a warning in the cpumask
code:

WARNING: at include/linux/cpumask.h:107

Which is:
        WARN_ON_ONCE(cpu >= nr_cpumask_bits);

The backtrace is:
        cpu_cmd
        cmds
        xmon_core
        xmon
        die

xmon is iterating through 0 to NR_CPUS. I'm not sure why we are still
open coding this but iterating above nr_cpu_ids is definitely a bug.

This patch iterates through all possible cpus, in case we issue a
system reset and CPUs in an offline state call in.

Perhaps the old code was trying to handle CPUs that were in the
partition but were never started (eg kexec into a kernel with an
nr_cpus= boot option). They are going to die way before we get into
xmon since we haven't set any kernel state up for them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit c9fe573a upstream.

In sound/soc/codecs/tlv320aic3x.c

        data = snd_soc_read(codec, AIC3X_PLL_PROGA_REG);
        snd_soc_write(codec, AIC3X_PLL_PROGA_REG,
                      data | (pll_p << PLLP_SHIFT));

In the above code, pll-p value is OR'ed with previous value without
clearing it. Bug is not seen if pll-p value doesn't change across
Sampling frequency.

However on some platforms (like AM335x EVM-SK), pll-p may have different
values across different sampling frequencies. In such case, above code
configures the pll with a wrong value.
Because of this bug, when a audio stream is played with pll value
different from previous stream, audio is heard as differently(like its
stretched).
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4b5ebccc upstream.

When receiving an "individually addressed" action frame, the
receiver is required to return it to the sender. mac80211
gets this wrong as it also returns group addressed (mcast)
frames to the sender. Fix this and update the reference to
the new 802.11 standards version since things were shuffled
around significantly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 7508b657 upstream.

https://bugzilla.kernel.org/show_bug.cgi?id=42903

Based on the work of <fynivx@gmail.com>
Signed-off-by: Panayiotis Karabassis <panayk@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f63d7dab upstream.

The latest Realtek driver for the RTL8188CU and RTL8192CU chips adds three
new USB IDs.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 03e934f6 upstream.

Sasha Levin reported following panic :

[ 2136.383310] BUG: unable to handle kernel NULL pointer dereference at
00000000000003b0
[ 2136.384022] IP: [<ffffffff8114e400>] __lock_acquire+0xc0/0x4b0
[ 2136.384022] PGD 131c4067 PUD 11c0c067 PMD 0
[ 2136.388106] Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
[ 2136.388106] CPU 1
[ 2136.388106] Pid: 24855, comm: trinity-child1 Tainted: G        W
3.5.0-rc2-sasha-00015-g7b268f7 #374
[ 2136.388106] RIP: 0010:[<ffffffff8114e400>]  [<ffffffff8114e400>]
__lock_acquire+0xc0/0x4b0
[ 2136.388106] RSP: 0018:ffff8800130b3ca8  EFLAGS: 00010046
[ 2136.388106] RAX: 0000000000000086 RBX: ffff88001186b000 RCX:
0000000000000000
[ 2136.388106] RDX: 0000000000000000 RSI: 0000000000000000 RDI:
0000000000000000
[ 2136.388106] RBP: ffff8800130b3d08 R08: 0000000000000001 R09:
0000000000000000
[ 2136.388106] R10: 0000000000000000 R11: 0000000000000001 R12:
0000000000000002
[ 2136.388106] R13: 00000000000003b0 R14: 0000000000000000 R15:
0000000000000000
[ 2136.388106] FS:  00007fa5b1bd4700(0000) GS:ffff88001b800000(0000)
knlGS:0000000000000000
[ 2136.388106] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2136.388106] CR2: 00000000000003b0 CR3: 0000000011d1f000 CR4:
00000000000406e0
[ 2136.388106] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[ 2136.388106] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7:
0000000000000400
[ 2136.388106] Process trinity-child1 (pid: 24855, threadinfo
ffff8800130b2000, task ffff88001186b000)
[ 2136.388106] Stack:
[ 2136.388106]  ffff8800130b3cd8 ffffffff81121785 ffffffff81236774
000080d000000001
[ 2136.388106]  ffff88001b9d6c00 00000000001d6c00 ffffffff130b3d08
ffff88001186b000
[ 2136.388106]  0000000000000000 0000000000000002 0000000000000000
0000000000000000
[ 2136.388106] Call Trace:
[ 2136.388106]  [<ffffffff81121785>] ? sched_clock_local+0x25/0x90
[ 2136.388106]  [<ffffffff81236774>] ? get_empty_filp+0x74/0x220
[ 2136.388106]  [<ffffffff8114e97a>] lock_acquire+0x18a/0x1e0
[ 2136.388106]  [<ffffffff836b37df>] ? rawsock_release+0x4f/0xa0
[ 2136.388106]  [<ffffffff837c0ef0>] _raw_write_lock_bh+0x40/0x80
[ 2136.388106]  [<ffffffff836b37df>] ? rawsock_release+0x4f/0xa0
[ 2136.388106]  [<ffffffff836b37df>] rawsock_release+0x4f/0xa0
[ 2136.388106]  [<ffffffff8321cfe8>] sock_release+0x18/0x70
[ 2136.388106]  [<ffffffff8321d069>] sock_close+0x29/0x30
[ 2136.388106]  [<ffffffff81236bca>] __fput+0x11a/0x2c0
[ 2136.388106]  [<ffffffff81236d85>] fput+0x15/0x20
[ 2136.388106]  [<ffffffff8321de34>] sys_accept4+0x1b4/0x200
[ 2136.388106]  [<ffffffff837c165c>] ? _raw_spin_unlock_irq+0x4c/0x80
[ 2136.388106]  [<ffffffff837c1669>] ? _raw_spin_unlock_irq+0x59/0x80
[ 2136.388106]  [<ffffffff837c2565>] ? sysret_check+0x22/0x5d
[ 2136.388106]  [<ffffffff8321de8b>] sys_accept+0xb/0x10
[ 2136.388106]  [<ffffffff837c2539>] system_call_fastpath+0x16/0x1b
[ 2136.388106] Code: ec 04 00 0f 85 ea 03 00 00 be d5 0b 00 00 48 c7 c7
8a c1 40 84 e8 b1 a5 f8 ff 31 c0 e9 d4 03 00 00 66 2e 0f 1f 84 00 00 00
00 00 <49> 81 7d 00 60 73 5e 85 b8 01 00 00 00 44 0f 44 e0 83 fe 01 77
[ 2136.388106] RIP  [<ffffffff8114e400>] __lock_acquire+0xc0/0x4b0
[ 2136.388106]  RSP <ffff8800130b3ca8>
[ 2136.388106] CR2: 00000000000003b0
[ 2136.388106] ---[ end trace 6d450e935ee18982 ]---
[ 2136.388106] Kernel panic - not syncing: Fatal exception in interrupt

rawsock_release() should test if sock->sk is NULL before calling
sock_orphan()/sock_put()
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
[bwh: Backported to 3.2: keep using nfc_dbg(), not pr_debug()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit bed3d9c0 upstream.

commit 7a532fe7
ath9k_hw: fix interpretation of the rx KeyMiss flag

This commit used the rx key miss indication to detect packets that were
passed from the hardware without being decrypted, however it seems that
this bit is not only undefined in the static WEP case, but also for
dynamically allocated WEP keys. This caused a regression when using
WEP-LEAP.

This patch fixes the regression by keeping track of which key indexes
refer to CCMP keys and only using the key miss indication for those.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 67de956f upstream.

Fix multiple remotely-exploitable stack-based buffer overflows due to
the NCI code pulling length fields directly from incoming frames and
copying too much data into statically-sized arrays.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: security@kernel.org
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
[bwh: Backported to 3.2:
 - Drop changes to parsing of tech B and tech F parameters
 - Various renaming]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f03ba7e9 upstream.

After association, STA will go through eapol handshake with WPS
enabled AP. It's observed that WPS handshake fails with some 11n
AP. The reason for the failure is that the eapol packet is sent
via 11n frame aggregation.

The eapol packet should be sent directly without 11n aggregation.

This patch fixes the problem by adding WPS session control while
dequeuing Tx packets for transmission.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: reformat the if-statement per earlier
 upstream commit c65a30f3]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 92583924 upstream.

Currently we check the sequence number of last packet received
against start_win. If a sequence hole is detected, start_win is
updated to next sequence number.

Since the rx sequence number is initialized to 0, a corner case
exists when BA setup happens immediately after association. As
0 is a valid sequence number, start_win gets increased to 1
incorrectly. This causes the first packet with sequence number 0
being dropped.

Initialize rx sequence number as 0xffff and skip adjusting
start_win if the sequence number remains 0xffff. The sequence
number will be updated once the first packet is received.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 32587371 upstream.

Fix a regression introduced by 7eaceacc ("block: remove per-queue
plugging").  In that patch, Jens removed the whole mm_unplug_device()
function, which used to be the trigger to make umem start to work.

We need to implement unplugging to make umem start to work, or I/O will
never be triggered.
Signed-off-by: Tao Guo <Tao.Guo@emc.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Shaohua Li <shli@kernel.org>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 047fe360 upstream.

Dave Jones reported a kernel BUG at mm/slub.c:3474! triggered
by splice_shrink_spd() called from vmsplice_to_pipe()

commit 35f3d14d (pipe: add support for shrinking and growing pipes)
added capability to adjust pipe->buffers.

Problem is some paths don't hold pipe mutex and assume pipe->buffers
doesn't change for their duration.

Fix this by adding nr_pages_max field in struct splice_pipe_desc, and
use it in place of pipe->buffers where appropriate.

splice_shrink_spd() loses its struct pipe_inode_info argument.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Tom Herbert <therbert@google.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[bwh: Backported to 3.2:
 - Adjust context in vmsplice_to_pipe()
 - Update one more call to splice_shrink_spd(), from skb_splice_bits()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 5870adc6 upstream.

bug introduced with 59b699cd

If the source or destination mac address of an ethernet packet
could not be found in the translation table the packet was
dropped if AP isolation was turned on. This behavior would
make it impossible to send broadcast packets over the mesh as
the broadcast address will never enter the translation table.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 5f160126 upstream.

The acpi_pad driver can get stuck in destroy_power_saving_task()
waiting for kthread_stop() to stop a power_saving thread.  The problem
is that the isolated_cpus_lock mutex is owned when
destroy_power_saving_task() calls kthread_stop(), which waits for a
power_saving thread to end, and the power_saving thread tries to
acquire the isolated_cpus_lock when it calls round_robin_cpu().  This
patch fixes the issue by making round_robin_cpu() use its own mutex.

https://bugzilla.kernel.org/show_bug.cgi?id=42981Signed-off-by: Stuart Hayes <Stuart_Hayes@Dell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 85f2f834 upstream.

The freescale arm i.MX series platform can support this driver, and
usually the arm cpu works in the little endian mode by default, while
device tree entry value is stored in big endian format, we should use
be32_to_cpup() to handle them, after modification, it can work well
both on the le cpu and be cpu.

Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 6bc96d04 upstream.

Fixes:
[   15.470311] WARNING: at /local/scratch/ianc/devel/kernels/linux/fs/sysfs/file.c:498 sysfs_attr_ns+0x95/0xa0()
[   15.470326] sysfs: kobject eth0 without dirent
[   15.470333] Modules linked in:
[   15.470342] Pid: 12, comm: xenwatch Not tainted 3.4.0-x86_32p-xenU #93
and
[    9.150554] BUG: unable to handle kernel paging request at 2b359000
[    9.150577] IP: [<c1279561>] linkwatch_do_dev+0x81/0xc0
[    9.150592] *pdpt = 000000002c3c9027 *pde = 0000000000000000
[    9.150604] Oops: 0002 [#1] SMP
[    9.150613] Modules linked in:

This is http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=675190Reported-by: George Shuklin <george.shuklin@gmail.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Tested-by: William Dauchy <wdauchy@gmail.com>
Cc: 675190@bugs.debian.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 3fcc8f96 upstream.

This patch adds 10 device IDs for CP210x based devices from the following manufacturers:
Timewave
Clipsal
Festo
Link Instruments
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>