This seems to fix problems with some powersaving clients since a
positive value in TBTT_SYNC_CFG_TBTT_ADJUST introduces beacon skew,
which is not wanted in AP mode.

Also update the rest of the TBTT_SYNC config according to the
legacy drivers in AP mode.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Allow passing a void pointer to rt2x00_queue_entry_for_each which in
turn in provided to the callback function.

Furthermore, allow the callback function to stop processing by returning
true. And also notify the caller of rt2x00_queue_entry_for_each if the
loop was canceled by the callback.

No functional changes, just preparation for an upcoming patch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The number of flags defined for the rt2x00dev->flags field,
has been growing over the years. Currently we are approaching
the maximum number of bits which are available in the field.

A secondary problem, is that one part of the field are initialized only
during boot, because the driver requirements are initialized or device
requirements are loaded from the EEPROM. In both cases, the flags are
fixed and will not change during device operation. The other flags are
the device state, and will change frequently. So far this resulted in the fact
that for some flags, the atomic bit accessors are used, while for the others
the non-atomic variants are used.

By splitting the flags up into a "flags" and "cap_flags" we can put all flags
which are fixed inside "cap_flags". This field can then be read non-atomically.
In the "flags" field we keep the device state, which is going to be read atomically.

This adds more room for more flags in the future, and sanitizes the field access methods.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since commit 0b7fde54 "rt2x00: Protect
queue control with mutex" rt2x00 used rt2x00queue_pause_queue for
stopping a tx queue in mac80211. But in case of a failure in the tx
path rt2x00 still called ieee80211_stop_queue which stopped the queue
but prevented rt2x00queue_unpause_queue to wake the queue up again
resulting in a stuck tx queue.

Fix this by also using rt2x00queue_pause_queue in case of tx failures.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds WLAN LED support to the mac80211 rt2x00 driver for
Ralink SoC (rt305x) devices.  The current WLAN LED drivers in
rt2800lib.c set the LED brightness via an MCU request, but do nothing
for SoC.  This patch checks for SoC and sets the register to enable the
WLAN LED (instead of an MCU request).  This enables the WLAN LED for
RT305x devices.
Signed-off-by: Layne Edwards <ledwards@astrumtech.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Frame filtering relies on having a valid destination index (keycache slot),
to keep track of the destination. Assigning a keycache slot (configured
to unencrypted, with no key data attached) improves powersave handling in
AP mode with no encryption.
The dummy keycache entry for a station is cleared, when a real key gets
added.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a long standing issue of pending packets in the queue being
sent (and retransmitted many times) to sleeping stations.
This was made worse by aggregation through driver-internal retransmitting
of A-MDPU subframes.
Previously the hardware tx filter was cleared unconditionally for every
single packet - with this patch it uses the IEEE80211_TX_CTL_CLEAR_PS_FILT
for unaggregated frames.
A sta_notify driver op is added to stop aggregation for stations when they
enter powersave mode. Subframes stay buffered inside the driver, to ensure
that the BlockAck window keeps a sane state.
Since the driver uses software aggregation, the clearing of the tx filter
needs to be handled by the driver instead of mac80211 for aggregated frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While leaving the oper channel, beacon generation is stopped
by mac80211 and beacon slots are marked as inactive.
During the scan, ath9k configures beacon timers
based on IEEE80211_CONF_OFFCHANNEL which inturn generates
beacon alert even though bslot is inactive.

ath9k fails to disable beacon alert while moving to offchannel
if none of the beacon slot is active. This is causing beacon
transmission on foreign channel. This patch enables swba
based on active bslots.

This issue was reported with two vifs (AP+STA) and triggered
scan in STA vif in unassociated state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This allows a driver to buffer frames for a PS station and tell mac80211
to wake it up even though mac80211 does not have any buffered frames for
it.
This is necessary for properly handling aggregation related buffering,
in ath9k, because the driver needs to keep its frames in order to keep
track of the Block-ACK window.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc_tx_get_slot can return zero as valid index.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1) removal of unnecessary mwifiex_device structure
2) avoid passing adapter pointer to mwifiex_init_sw()
3) remove local variable drv_mode_info in mwifiex_add_card()
4) type change in mwifiex_bss_attr to match mwifiex_private
5) removal of more wordy comments
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

use corresponding macros defined in include/linux/ieee80211.h
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove some local variables (mainly function return values)
that are used only once. Also, one dummy function and some
wordy comments are removed.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix printf() format warning (tm_year is long int):

net/mac80211/debugfs_sta.c:113: warning: format '%d' expects type 'int', but argument 4 has type 'long int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit be663ab6 (iwlwifi: split the drivers for
agn and legacy devices 3945/4965) added code to read the 4965's revision ID from
the PCI configuration register while it's already stored by PCI subsystem in the
'revision' field of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Move the ath9k_htc debugfs under ieee80211 to be inline
with ath9k driver and it also helps to simplify debug code.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The 0x6C regulatory domain is just like the 0x6A regulatory
domain but differs in that 0x6C will allow adhoc and active
scan on its channels only if we are associated to an AP
with a country IE that allows those channels. The
ath_reg_apply_beaconing_flags() does just this -- we respect
the manufacturer's intent on only enabling beaconing modes
of operation if and only if blessed by the country IE.

Cc: David Quan <david.quan@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a regulator consumer driver for rfkill to enable controlling radio
transmitters connected to voltage regulators using the regulator
framework.

A new "vrfkill" virtual supply is provided to use in platform code.
Signed-off-by: Guiming Zhuo <gmzhuo@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

No longer use, remove it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

No longer used by _agn devices, remove it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

After driver split, no need to use ieee80211_ops, remove it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

For bgn devices, there were no HT40 channels value in EEPROM
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Thermal throttling functions are available for all _agn devices, call the
functions directly.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

All _agn devices support continuous uCode trace, remove checking
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

When testing some new P2P code, Angie found that the
driver might crash because the beacon command ended
up being bigger than a regular command. This is quite
obvious -- a normal command is limited to roughly 360
bytes but a beacon may be much larger of course.

To fix this, use the huge command buffer.
Reported-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Since huge commands all share a single buffer,
there can only be a single one in flight at a
time since otherwise they'd overwrite each
other. This is true in the driver now, but it
seems like a possible source of bugs, so add
a test to verify that huge commands are always
sent synchronously.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

There are a number of things in the driver that
may result in a BUG(), which is suboptimal since
it's hard to get debugging information out of
the driver in that case and the user experience
is also not good :-)

Almost all BUG_ON instances can be converted to
WARN_ON with a few lines of appropriate error
handling, so do that instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

After driver split, no need to call led functions through callback
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Fix a regression from the L2CAP "rewrite" patches.
Purge the tx_q already happens on l2cap_chan_del() so we don't need it at
l2cap_disconnect_req().
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

l2cap_get_sock_by_scid was changed to not lock the socket anymore, but I
forgot to change all the users of this function.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Some customers use 0x6C world regulatory domain and this patch
adds the support.

Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In http://lkml.indiana.edu/hypermail/linux/kernel/1104.1/01955.html, Geerti
Uytterhoeven reports the following warnings for the rtlwifi drivers.

src/drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c: warning:
	 'cck_index' may be used uninitialized in this function: => 637
src/drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c: warning:
	 'cck_index_old' may be used uninitialized in this function: => 637
src/drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: warning:
	 'box_extreg' may be used uninitialized in this function: => 303
src/drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: warning:
	 'box_reg' may be used uninitialized in this function: => 303
src/drivers/net/wireless/rtlwifi/rtl8192ce/rf.c: warning:
	 'chnlgroup' may be used uninitialized in this function: => 205
src/drivers/net/wireless/rtlwifi/rtl8192ce/rf.c: warning:
	 'u4_regvalue' may be used uninitialized in this function: => 450
src/drivers/net/wireless/rtlwifi/rtl8192cu/hw.c: warning:
	 'hq_sele' may be used uninitialized in this function: => 924
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The old function name sounds like checking for existing BA
stream. The function actually checks if we have room for
creating new BA stream or not.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some function parameters become useless after previous
cleanup changes.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The return statement at the last line of a void function
is not necessary.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1) remove mwifiex_alloc_fill_wait_queue() and
mwifiex_request_ioctl()
2) avoid dynamic allocation of wait queue
3) remove unnecessary mwifiex_error_code macros that
were used mainly by the wait queue status code
4) remove some abstraction functions
5) split mwifiex_prepare_cmd() to mwifiex_send_cmd_async()
and mwifiex_send_sync() to handle asynchronous and
synchronous commands respectively
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There are two variants of AR5312 dual-band devices, one single-radio
and the other one dual-radio. On the dual-radio board, the first MAC
only supports 5 GHz, even though it has a dual-band PHY. The 2.4 GHz
part of this phy is used in pass-through mode, connecting the second
MAC with the second PHY.
Disable 2.4 GHz for the first MAC on an AR5312, but only if the board
configuration indicates a dual-radio device.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>