- 29 Nov, 2016 3 commits
-
-
Hannes Reinecke authored
Add a sysfs attribute 'ctlr_num' holding the current HPSA controller number. This is required to construct compability 'cciss' links. [mkp: fixed typo] Signed-off-by:
Hannes Reinecke <hare@suse.com> Acked-by:
Don Brace <don.brace@microsemi.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Hannes Reinecke authored
NOT_READY is a sense key, not a legit scsi hostbyte value. Use DID_NO_CONNECT instead. Signed-off-by:
-
Bart Van Assche authored
Additionally, rename srp_wait_for_queuecommand() into scsi_wait_for_queuecommand() and add a comment about the queuecommand() call from scsi_send_eh_cmnd(). Note: this patch changes scsi_internal_device_block from a function that did not sleep into a function that may sleep. This is fine for all callers of this function: * scsi_internal_device_block() is called from the mpt3sas device while that driver holds the ioc->dm_cmds.mutex. This means that the mpt3sas driver calls this function from thread context. * scsi_target_block() is called by __iscsi_block_session() from kernel thread context and with IRQs enabled. * The SRP transport code also calls scsi_target_block() from kernel thread context while sleeping is allowed. * The snic driver also calls scsi_target_block() from a context from which sleeping is allowed. The scsi_target_block() call namely occurs immediately after a scsi_flush_work() call. [mkp: s/shost/sdev/] Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Reviewed-by:
-
- 25 Nov, 2016 13 commits
-
-
Dan Carpenter authored
We verified that resp_code is FC_SPP_RESP_ACK earlier so we don't need to check again here. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Johannes Thumshirn <jth@kernel.org> Signed-off-by:
-
Santosh Y authored
Reported-by:
Venkatraman S <svenkatr@ti.com> Reviewed-by:
Vinayak Holikatti <vinholikatti@gmail.com> Signed-off-by:
Santosh Y <santoshsy@gmail.com> Signed-off-by:
Zhangfei Gao <zhangfei.gao@linaro.org> Reviewed-by:
Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by:
-
Xiang Chen authored
Add the function to set PHY min and max linkrate through sysfs interface. Signed-off-by:
Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by:
John Garry <john.garry@huawei.com> Reviewed-by:
-
John Garry authored
Sometimes the value of hisi_sas_device.running_req would go negative unless we have the check for running_req >= 0 before trying to decrement. This is because using running_req is not thread-safe. As such, the value for running_req may be actually incorrect, so use atomic64_t instead. Signed-off-by:
-
Xiang Chen authored
Check ERR bit of status to decide whether there is something wrong with initial register-D2H FIS. If error exists, PHY reset the channel to restart OOB. Signed-off-by:
-
Xiang Chen authored
Modify and add some SATA commands according to SATA protocol. Signed-off-by:
-
Xiang Chen authored
Delete repeated configuration items for hisi_sas_device() when we free a device. These items are now only set in hisi_sas_dev_gone(). Signed-off-by:
-
Xiang Chen authored
sas_scsi_find_task() only deals with return value TMF_RESP_FUNC_FAILED/TMF_RESP_FUNC_SUCC/TMF_RESP_FUNC_COMPLETE of query task. So for LLDD errors just return TMF_RESP_FUNC_FAILED. Signed-off-by:
-
Xiang Chen authored
Replace WARN_ON() with dev_warn() print when internal abort fails. Signed-off-by:
-
Xiang Chen authored
When we form a wideport, we should use hardware PHY port_id instead of sas_phy->id. Signed-off-by:
-
Xiang Chen authored
There are many BROADCAST primitives generated by the host. We are only interested in BROADCAST (CHANGE) primitives currently, so only process this. Signed-off-by:
-
Xiang Chen authored
Currently slots are allocated from queues in a round-robin fashion. This causes a problem for internal commands in device mode. For this mode, we should ensure that the internal abort command is the last command seen in the host for that device. We can only ensure this when we place the internal abort command after the preceding commands for device that in the same queue, as there is no order in which the host will select a queue to execute the next command. This queue restriction makes supporting scsi mq more tricky in the future, but should not be a blocker. Note: Even though v1 hw does not support internal abort, the allocation method is chosen to be the same for consistency. Signed-off-by: -
Xiang Chen authored
For ECC 1bit error, logic can recover it, so we only print a warning. For ECC multi-bit and AXI bus fatal error, we panic. Signed-off-by:
-
- 22 Nov, 2016 4 commits
-
-
Quentin Lambert authored
Most error branches following the call to pmcraid_get_free_cmd contain a call to pmcraid_return_cmd. This patch add these calls where they are missing. Moreover, most error branches following the call to class_create contain a call to class_destroy. This patch add these calls where they are missing. This issue was found with Hector. Signed-off-by:
Quentin Lambert <lambert.quentin@gmail.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
-
Kiwoong Kim authored
Some UFS host controllers may think granularities of PRDT length and offset as bytes, not double words. Signed-off-by:
Kiwoong Kim <kwmad.kim@samsung.com> Reviewed-by:
-
Bjorn Andersson authored
ufs_qcom_init() sets the hba priv data before attempting to acquire the phy handle, so make sure to clear this in the case of an error. Failing to do this will make ufs_qcom_setup_clocks() operate on the uninitalized host object. Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by:
-
Arnd Bergmann authored
These two macros cause lots of warnings with gcc-7: drivers/scsi/bfa/bfa_svc.c: In function 'bfa_fcxp_meminfo': drivers/scsi/bfa/bfa_svc.c:521:103: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context] Using inline functions makes them much more readable and avoids the warnings. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Acked by: Anil Gurumurthy <anil.gurumurthy@cavium.com> Signed-off-by:
-
- 18 Nov, 2016 16 commits
-
-
Helge Deller authored
Fix the printk continuations when running the mptfusion driver. This patch brings the capabilities into one single syslog line again: mptbase: ioc1: Initiating bringup ioc1: LSI53C1030 B2: Capabilities={Initiator,Target} scsi host3: ioc1: LSI53C1030 B2, FwRev=01032341h, Ports=1, MaxQ=255, IRQ=67 Tested on a parisc C8000 machine. Signed-off-by:Helge Deller <deller@gmx.de> Signed-off-by:
-
Hannes Reinecke authored
Use pci_alloc_irq_vectors and drop the hand-crafted interrupt affinity routines. Signed-off-by:
Raghava Aditya Renukunta <raghavaaditya.renukunta@microsemi.com> Signed-off-by:
-
Johannes Thumshirn authored
Now that all conversions are done, move the FibreChannel bsg code over to the bsg library. This patch is derived from work done by Mike Christie in 2011 [1] but only the iscsi parts got merged back then. [1] http://marc.info/?l=linux-scsi&m=131149780921009&w=2Signed-off-by:
-
Johannes Thumshirn authored
Add bsg_job_put() and bsg_job_get() so don't need to export bsg_destroy_job() any more. Signed-off-by:
-
Johannes Thumshirn authored
fc_bsg_jobdone() and bsg_job_done() are 1:1 copies now so use the bsg-lib one instead of the FC private implementation. Signed-off-by:
Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by:
-
Johannes Thumshirn authored
bsg_softirq_done() and fc_bsg_softirq_done() are copies of each other, so ditch the fc specific one. Signed-off-by:
-
Johannes Thumshirn authored
fc_destroy_bsgjob() and bsg_destroy_job() are now 1:1 copies, so use the latter. As bsg_destroy_job() comes from bsg-lib we need to select it in Kconfig once CONFOG_SCSI_FC_ATTRS is active. Signed-off-by:
-
Johannes Thumshirn authored
Change FC drivers to use 'struct bsg_job' from bsg-lib.h instead of 'struct fc_bsg_job' from scsi_transport_fc.h and remove 'struct fc_bsg_job'. Signed-off-by:
-
Johannes Thumshirn authored
Add reference counting to 'struct bsg_job' so we can implement a reuqest timeout handler for bsg_jobs, which is needed for Fibre Channel. Signed-off-by:
-
Johannes Thumshirn authored
Implement kref backed reference counting instead of rolling our own. This elimnates the need of the following fields in 'struct fc_bsg_job': * ref_cnt * state_flags * job_lock bringing us close to unification of 'struct fc_bsg_job' and 'struct bsg_job'. Signed-off-by:
-
Johannes Thumshirn authored
Don't set FC_RQST_STATE_DONE before calling fc_bsg_jobdone() as fc_bsg_jobdone() calls blk_complete_requeust() which raises a soft-IRQ that ends up in fc_bsg_sofirq_done() and fc_bsg_softirq_done() sets the FC_RQST_STATE_DONE flag. Signed-off-by:
-
Johannes Thumshirn authored
Provide fc_bsg_to_rport() helper that will become handy when we're moving from struct fc_bsg_job to a plain struct bsg_job. Also move all LLDDs to use the new helper. Signed-off-by:
-
Johannes Thumshirn authored
Provide fc_bsg_to_shost() helper that will become handy when we're moving from struct fc_bsg_job to a plain struct bsg_job. Also use this little helper in the LLDDs. Signed-off-by:
-
Johannes Thumshirn authored
Export fc_bsg_jobdone so drivers can use it directly instead of doing the round-trip via struct fc_bsg_job::job_done() and use it in the LLDDs. That way we can also unify the interfaces of fc_bsg_jobdone and bsg_job_done. As we've converted all LLDDs over to use fc_bsg_jobdone() directly, we can remove the function pointer from struct fc_bsg_job as well. Signed-off-by:
Christoph Hellwig <hch@lst.de> Acked-by:
-
Johannes Thumshirn authored
Don't use fc_bsg_job::request and fc_bsg_job::reply directly, but use helper variables bsg_request and bsg_reply. This will be helpful when transitioning to bsg-lib. Signed-off-by:
-
Johannes Thumshirn authored
struct fc_bsg_buffer is just a clone of struct bsg_buffer from bsg-lib, so use this one instead. Signed-off-by:
-
- 17 Nov, 2016 4 commits
-
-
Arnd Bergmann authored
gcc-7 notices that the condition in mvs_94xx_command_active looks suspicious: drivers/scsi/mvsas/mv_94xx.c: In function 'mvs_94xx_command_active': drivers/scsi/mvsas/mv_94xx.c:671:15: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context] This was introduced when the mv_printk() statement got added, and leads to the condition being ignored. This is probably harmless. Changing '&&' to '&' makes the code look reasonable, as we check the command bit before setting and printing it. Fixes: a4632aae ("[SCSI] mvsas: Add new macros and functions") Signed-off-by:
-
Geliang Tang authored
Use module_pci_driver() helper to simplify the code. Signed-off-by:
Geliang Tang <geliangtang@gmail.com> Acked-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
-
Satish Kharat authored
Signed-off-by:
Satish Kharat <satishkh@cisco.com> Signed-off-by:
Sesidhar Baddela <sebaddel@cisco.com> Reviewed-by:
-
Zang Leigang authored
Add a new ufshcd_state, indicats that an err handler may get to run immediately. Use UFSHCD_STATE_ERROR here looks not literaly correct. Signed-off-by:
Zang Leigang <zangleigang@hisilicon.com> Reviewed-by:
-
