Fix a panic that would occur in the VF if the PF driver failed or was
removed from the host kernel. In this case, the VF driver calls
i40evf_close(), but this function does nothing because the driver is in
the resetting state. Because of this, the driver doesn't free its irqs
and causes a kernel panic when it tries to disable MSI-X.

Change-ID: If95644a89e554b4d7be0dca1b6add26f63047129
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In case of any AQ command to query port's DCB configuration fails
during driver's probe time; the probe fails and returns an error.

This patch prevents this issue by continuing the driver probe even
when an error is returned.

Also, added an error message to dump the AQ error status to show what
error caused the failure to get the DCB configuration from firmware.

Change-ID: Ifd5663512588bca684069bb7d4fb586dd72221af
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The queue vectors are originally distributed among the total
number of queues that are configured for a given VSI. The number
of queues that are configured for a VSI depends on the number of
TCs that are enabled for the VSI at VSI setup/creation time.

But, the total number of queues that are configured for a VSI may
change based on change in the total number of TCs enabled as a
result of change in DCB configuration based on DCBX.

Hence, it is required for the queue vectors to be redistributed
when the total queues that are configured for a given VSI changes.

Without redistributing the vectors the queues that are configured
for the newly enabled TCs may not be able to do any Tx/Rx.

Change-ID: I4e780903db019e6199c7ce43627cef22c916acfe
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver version string was added to this struct to be passed
down through the firmware to low-level NC-SI functions. We tell
the firmware about the length of the ASCII string not counting
any terminating null.

Change-ID: I09ac98ff9b869e8661c55fc6a5c98808fc280c91
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Anjali Singhai <anjali.singhai@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The function to set the VF MAC address was not taking the port VLAN
filter into account when setting/clearing/resetting the VF's host
administered MAC address.  Be sure to use the port VLAN for VF MAC
filtering configurations.

Change-ID: I12595331981c79529738f041dcdbdb667ef8f5e6
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for getting and setting RSS hashing options, RSS LUT
entries, and getting the number of device channels from ethtool. Because
the LUT is so small for the VFs, we just read and write the device
registers directly instead of maintaining a shadow copy.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We were already taking care to retain the MAC filter list when deleting a
port VLAN.  Take some additional care to retain the MAC filter list when
changing a port VLAN.

Change-ID: Iacf9599ea24ecb4dca8e419aacaf4b58ca361a9c
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes the unnecessary ptp_tx_work item. It conflicts with
the interrupt-based handler, and will cause spurious warning messages to
be displayed in the kernel log. Since the hardware can properly trigger
an interrupt, we do not need to poll for an available timestamp in a
work queue any more.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When we change the list of action on a given filter, currently we don't
change it to empty. This is a bug, we should allow to change to whatever
users given.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When actions are attached to a filter, they are a part of the filter
itself, so when changing a filter we should allow to overwrite the actions
inside as well.

In my specific case, when I tried to _append_ a new action to an existing
filter which already has an action, I got EEXIST since kernel refused
to overwrite the existing one in kernel.

This patch checks if we are changing the filter checking NLM_F_CREATE flag
(Sigh, filters don't use NLM_F_REPLACE...) and then passes the boolean down
to actions. This fixes the problem above.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jitendra Kalsaria says:

====================
qlcnic driver updates

This patch series containes following changes -
* Optimize MAC learning code.
* Export board temperature using hwmon-sysfs interface.
* Add support for configuring Tx interrupt coalescing parameters from VF.
* Logging error messages in error path.
* Restrict extended vNIC support in legacy interrupt mode and log appropriate
  message.

Please apply this series to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o When the driver loads in legacy interrupt mode, only vNICs
  with PCI function number 0-7 are supported.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Tx interrupt coalescing parameters can now be set from VF.
o Added validation code in PF to validate the parameters.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* Use rx_mac_learn instead of mac_learn and eSwitch flag check in Rx path of
  82xx adapter.
* Check for MAC filter overrun only after driver scans through cached MAC address list.
  This will help to update the time stamp of cached MAC addresses even if
  adapter runs out of MAC address filter limit.
* Remove expensive log thrown by driver when MAC address filters are exhausted
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.

Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of our FDDI support code has been apparently written with an
assumption that tabs are 4-character wide.  In preparation to the next
change this update reformats <linux/if_fddi.h> so that it stays within 79
columns and otherwise renders correctly with 8-character tabs.  No
functional change.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit a8b9b96e ("tipc: fix race
in disc create/delete") leads to the following static checker warning:

	net/tipc/discover.c:352 tipc_disc_create()
		warn: possible memory leak of 'req'

The risk of memory leak really exists in practice. Especially when
it's failed to allocate memory for "req->buf", tipc_disc_create()
doesn't free its allocated memory, instead just directly returns
with ENOMEM error code. In this situation, memory leak, of course,
happens.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use a newline character appropriately.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: Broadcom SYSTEMPORT driver

This patchset adds support for the Broadcom SYSTEMPORT Ethernet MAC
controller which is used in the latest Broadcom BCM7xxx Set Top Box
System-on-a-Chip. This Ethernet MAC is interfaced to an internal
switch which will get a separate driver submitted later on.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add an entry in the MAINTAINERS file listing myself as the maintainer
for the Broadcom SYSTEMPORT Ethernet MAC controller driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hook the Broadcom SYSTEMPORT driver into the build system under the
SYSTEMPORT Kconfig symbol.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the Device Tree bindings documentation for the Broadcom SYSTEMPORT
Ethernet MAC controller hardware.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SYSTEMPORT is the latest Ethernet MAC hardware block used on newer
BCM7xxx Set Top Box SoCs in conjunction with an internal Ethernet
switch. This patch adds support for this hardware block along with the
following hardware features:

- support for hardware checksum offload (transmit and receive)
- support for the 32 transmit queues
- MIB counters reading
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to igb only.

Carolyn provides a number of cleanups to fix checkpatch warnings/errors
and two minor issues found by coccicheck.

v2: update patch indentation for patch 07 of the series based on feedback
    from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not initialize list twice.
list_replace_init() already takes care of initializing list.
We don't need to initialize it with LIST_HEAD() beforehand.
Signed-off-by: xiao jin <jin.xiao@intel.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not initialize net_kill_list twice.
list_replace_init() already takes care of initializing net_kill_list.
We don't need to initialize it with LIST_HEAD() beforehand.
Signed-off-by: xiao jin <jin.xiao@intel.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
this is a pull request of 10 patches for net-next/master.

It consists of three patches by Alexander Shiyan, which improve the
mcp251x driver. Stefano Babic's patch move the SPI driver into a sub
folder. The three patches by Olivier Sobrie add support for the Kvaser
Leaf v2 and usb mini PCIe hardware to the existing driver. Alexander
Stein contributes eg20t support to the c_can pci driver. Together with
the patches on the net-tree, we'll be able to remove the pch_can driver
soon. Kurt Van Dijck's two patches clean up the sysfs attributes of the
softing driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Aring says:

====================
at86rf230 cleanup

this is the first patch series to cleanup the at86rf230 driver. Later I want
to implement regmap and a asynchron spi handling for transmit and receiving
frames.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The function is small enough, we don't need a extra function for this.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes a unnecessary state read. The status value is never
evaluate after reading the state.

Also rename the status variable to dvdd, because this variable will be
used later.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resets the irq line before we are requesting the irq. This
avoids pending interrupts before requesting.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is already handled by the of_match_ptr macro.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a at86rf230_device_id table to offers various module
aliases.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>