The kmemleak_disable() function could be called from various contexts
including IRQ. It creates a clean-up thread but the kthread_create()
function has restrictions on which contexts it can be called from,
mainly because of the kthread_create_lock. The patch changes the
kmemleak clean-up thread to a workqueue.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Eric Paris <eparis@redhat.com>

This patch changes the for_each_process() loop with the
do_each_thread()/while_each_thread() pair.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Ingo Molnar reported the following kmemcheck warning when running both
kmemleak and kmemcheck enabled:

  PM: Adding info for No Bus:vcsa7
  WARNING: kmemcheck: Caught 32-bit read from uninitialized memory
  (f6f6e1a4)
  d873f9f600000000c42ae4c1005c87f70000000070665f666978656400000000
   i i i i u u u u i i i i i i i i i i i i i i i i i i i i i u u u
           ^

  Pid: 3091, comm: kmemleak Not tainted (2.6.31-rc7-tip #1303) P4DC6
  EIP: 0060:[<c110301f>] EFLAGS: 00010006 CPU: 0
  EIP is at scan_block+0x3f/0xe0
  EAX: f40bd700 EBX: f40bd780 ECX: f16b46c0 EDX: 00000001
  ESI: f6f6e1a4 EDI: 00000000 EBP: f10f3f4c ESP: c2605fcc
   DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
  CR0: 8005003b CR2: e89a4844 CR3: 30ff1000 CR4: 000006f0
  DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
  DR6: ffff4ff0 DR7: 00000400
   [<c110313c>] scan_object+0x7c/0xf0
   [<c1103389>] kmemleak_scan+0x1d9/0x400
   [<c1103a3c>] kmemleak_scan_thread+0x4c/0xb0
   [<c10819d4>] kthread+0x74/0x80
   [<c10257db>] kernel_thread_helper+0x7/0x3c
   [<ffffffff>] 0xffffffff
  kmemleak: 515 new suspected memory leaks (see
  /sys/kernel/debug/kmemleak)
  kmemleak: 42 new suspected memory leaks (see /sys/kernel/debug/kmemleak)

The problem here is that kmemleak will scan partially initialized
objects that makes kmemcheck complain. Fix that up by skipping
uninitialized memory regions when kmemcheck is enabled.
Reported-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>

This block is allocated with alloc_bootmem() and scanned by kmemleak but
the kernel direct mapping may no longer exist. This patch tells kmemleak
to ignore this memory hole. The dma32_bootmem_ptr in
dma32_reserve_bootmem() is also ignored.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>

Introducing printing of the objects hex dump to the seq file.
The number of lines to be printed is limited to HEX_MAX_LINES
to prevent seq file spamming. The actual number of printed
bytes is less than or equal to (HEX_MAX_LINES * HEX_ROW_SIZE).

(slight adjustments by Catalin Marinas)
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This patch sets the min_count for alloc_bootmem objects to 0 so that
they are never reported as leaks. This is because many of these blocks
are only referred via the physical address which is not looked up by
kmemleak.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>

Before slab is initialised, kmemleak save the allocations in an early
log buffer. They are later recorded as normal memory allocations. This
patch adds the stack trace saving to the early log buffer, otherwise the
information shown for such objects only refers to the kmemleak_init()
function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This buffer isn't needed after kmemleak was initialised so it can be
freed together with the .init.data section. This patch also marks
functions conditionally accessing the early log variables with __ref.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

By writing dump=<addr> to the kmemleak file, kmemleak will look up an
object with that address and dump the information it has about it to
syslog. This is useful in debugging memory leaks.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

If the object size is bigger than a predefined value (4K in this case),
release the object lock during scanning and call cond_resched().
Re-acquire the lock after rescheduling and test whether the object is
still valid.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  virtio: net refill on out-of-memory
  smc91x: fix compilation on SMP

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/ps3: Update ps3_defconfig
  powerpc/ps3: Add missing check for PS3 to rtc-ps3 platform device registration

Update ps3_defconfig.

 o Refresh for 2.6.31.
 o Remove MTD support.
 o Add more HID drivers.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

On non-PS3, we get:

| kernel BUG at drivers/rtc/rtc-ps3.c:36!

because the rtc-ps3 platform device is registered unconditionally in a kernel
with builtin support for PS3.
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  IMA: iint put in ima_counts_get and put

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k,m68knommu: Wire up rt_tgsigqueueinfo and perf_counter_open
  m68k: Fix redefinition of pgprot_noncached
  arch/m68k/include/asm/motorola_pgalloc.h: fix kunmap arg
  m68k: cnt reaches -1, not 0
  m68k: count can reach 51, not 50

If we change the inverted attribute to another value, the LED will not be
inverted until we change the GPIO state.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Samuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When setting the same GPIO number, multiple IRQ shared requests will be
done without freing the previous request.  It will also try to free a
failed request or an already freed IRQ if 0 was written to the gpio file.

All these oops and leaks were fixed with the following solution: keep the
previous allocated GPIO (if any) still allocated in case the new request
fails.  The alternative solution would desallocate the previous allocated
GPIO and set gpio as 0.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Samuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This failure is very common on many platforms.  Handling it in the ACPI
processor driver is enough, and we don't need a warning message unless
CONFIG_ACPI_DEBUG is set.

Based on a patch from Zhang Rui.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13389Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If the BIOS reports an invalid throttling state (which seems to be
fairly common after system boot), a reset is done to state T0.
Because of a check in acpi_processor_get_throttling_ptc(), the reset
never actually gets executed, which results in the error reoccurring
on every access of for example /proc/acpi/processor/CPU0/throttling.

Add a 'force' option to acpi_processor_set_throttling() to ensure
the reset really takes effect.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13389

This patch, together with the next one, fixes a regression introduced in
2.6.30, listed on the regression list. They have been available for 2.5
months now in bugzilla, but have not been picked up, despite various
reminders and without any reason given.

Google shows that numerous people are hitting this issue. The issue is in
itself relatively minor, but the bug in the code is clear.

The patches have been in all my kernels and today testing has shown that
throttling works correctly with the patches applied when the system
overheats (http://bugzilla.kernel.org/show_bug.cgi?id=13918#c14).
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Summary:
Kernel panic arise when stack protection is enabled, since strncat will
add a null terminating byte '\0'; So in functions
like this one (wmi_query_block):
        char wc[4]="WC";
	....
	strncat(method, block->object_id, 2);
        ...
the length of wc should be n+1 (wc[5]) or stack protection
fault will arise. This is not noticeable when stack protection is
disabled,but , isn't good either.
Config used: [CONFIG_CC_STACKPROTECTOR_ALL=y,
	      CONFIG_CC_STACKPROTECTOR=y]

Panic Trace
------------
       .... stack-protector: kernel stack corrupted in : fa7b182c
       2.6.30-rc8-obelisco-generic
       call_trace:
           [<c04a6c40>] ? panic+0x45/0xd9
	   [<c012925d>] ? __stack_chk_fail+0x1c/0x40
	   [<fa7b182c>] ? wmi_query_block+0x15a/0x162 [wmi]
	   [<fa7b182c>] ? wmi_query_block+0x15a/0x162 [wmi]
	   [<fa7e7000>] ? acer_wmi_init+0x00/0x61a [acer_wmi]
	   [<fa7e7135>] ? acer_wmi_init+0x135/0x61a [acer_wmi]
	   [<c0101159>] ? do_one_initcall+0x50+0x126

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13514Signed-off-by: Costantino Leandro <lcostantino@gmail.com>
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Jens reported early_ioremap messages with old ASUS board...

> [    1.507461] pci 0000:00:09.0: Firmware left e100 interrupts enabled; disabling
> [    1.532778] early_ioremap(3fffd080, 0000005c) [0] => Pid: 1, comm: swapper Not tainted 2.6.31-rc4 #36
> [    1.561007] Call Trace:
> [    1.568638]  [<c136e48b>] ? printk+0x18/0x1d
> [    1.581734]  [<c15513ff>] __early_ioremap+0x74/0x1e9
> [    1.596898]  [<c15515aa>] early_ioremap+0x1a/0x1c
> [    1.611270]  [<c154a187>] __acpi_map_table+0x18/0x1a
> [    1.626451]  [<c135a7f8>] acpi_os_map_memory+0x1d/0x25
> [    1.642129]  [<c119459c>] acpi_tb_verify_table+0x20/0x49
> [    1.658321]  [<c1193e50>] acpi_get_table_with_size+0x53/0xa1
> [    1.675553]  [<c1193eae>] acpi_get_table+0x10/0x15
> [    1.690192]  [<c155cc19>] acpi_processor_init+0x23/0xab
> [    1.706126]  [<c1001043>] do_one_initcall+0x33/0x180
> [    1.721279]  [<c155cbf6>] ? acpi_processor_init+0x0/0xab
> [    1.737479]  [<c106893a>] ? register_irq_proc+0xaa/0xc0
> [    1.753411]  [<c10689b7>] ? init_irq_proc+0x67/0x80
> [    1.768316]  [<c15405e7>] kernel_init+0x120/0x176
> [    1.782678]  [<c15404c7>] ? kernel_init+0x0/0x176
> [    1.797062]  [<c10038b7>] kernel_thread_helper+0x7/0x10
> [    1.812984] 00000080 + ffe00000

that is rather later.
acpi_gbl_permanent_mmap should be set in acpi_early_init()
if acpi is not disabled

and we have
> [    0.000000] ASUS P2B-DS detected: force use of acpi=ht

just don't load acpi_processor_init...
Reported-and-tested-by: Jens Rosenboom <jens@leia.mcbone.net>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The return value of the get_temp function is not checked when doing a
thermal zone update.  This may lead to a critical shutdown if get_temp
fails and the content of the temp variable is incorrectly set higher than
the critical trip point.

This has been observed on a system with incorrect ACPI implementation
where the corresponding methods were not serialized and therefore
sometimes triggered ACPI errors (AE_ALREADY_EXISTS).  The following
critical shutdowns indicated a temperature of 2097 C, which was obviously
wrong.

The patch adds a return value check that jumps over all trip point
evaluations printing a warning if get_temp fails.  The trip points are
evaluated again on the next polling interval with successful get_temp
execution.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Spotted by Hiroshi Shimamoto who also provided the test-case below.

copy_process() uses signal->count as a reference counter, but it is not.
This test case

	#include <sys/types.h>
	#include <sys/wait.h>
	#include <unistd.h>
	#include <stdio.h>
	#include <errno.h>
	#include <pthread.h>

	void *null_thread(void *p)
	{
		for (;;)
			sleep(1);

		return NULL;
	}

	void *exec_thread(void *p)
	{
		execl("/bin/true", "/bin/true", NULL);

		return null_thread(p);
	}

	int main(int argc, char **argv)
	{
		for (;;) {
			pid_t pid;
			int ret, status;

			pid = fork();
			if (pid < 0)
				break;

			if (!pid) {
				pthread_t tid;

				pthread_create(&tid, NULL, exec_thread, NULL);
				for (;;)
					pthread_create(&tid, NULL, null_thread, NULL);
			}

			do {
				ret = waitpid(pid, &status, 0);
			} while (ret == -1 && errno == EINTR);
		}

		return 0;
	}

quickly creates an unkillable task.

If copy_process(CLONE_THREAD) races with de_thread()
copy_signal()->atomic(signal->count) breaks the signal->notify_count
logic, and the execing thread can hang forever in kernel space.

Change copy_process() to increment count/live only when we know for sure
we can't fail.  In this case the forked thread will take care of its
reference to signal correctly.

If copy_process() fails, check CLONE_THREAD flag.  If it it set - do
nothing, the counters were not changed and current belongs to the same
thread group.  If it is not set, ->signal must be released in any case
(and ->count must be == 1), the forked child is the only thread in the
thread group.

We need more cleanups here, in particular signal->count should not be used
by de_thread/__exit_signal at all.  This patch only fixes the bug.
Reported-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

An mlocked page might lose the isolatation race.  This causes the page to
clear PG_mlocked while it remains in a VM_LOCKED vma.  This means it can
be put onto the [in]active list.  We can rescue it by using try_to_unmap()
in shrink_page_list().

But now, As Wu Fengguang pointed out, vmscan has a bug.  If the page has
PG_referenced, it can't reach try_to_unmap() in shrink_page_list() but is
put into the active list.  If the page is referenced repeatedly, it can
remain on the [in]active list without being moving to the unevictable
list.

This patch fixes it.
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Reviewed-by: KOSAKI Motohiro <&lt;kosaki.motohiro@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It's problematic to allow signed element_nr's or total's to be passed as
part of the flex array API.

flex_array_alloc() allows total_nr_elements to be set to a negative
quantity, which is obviously erroneous.

flex_array_get() and flex_array_put() allows negative array indices in
dereferencing an array part, which could address memory mapped before
struct flex_array.

The fix is to convert all existing element_nr formals to be qualified as
unsigned.  Existing checks to compare it to total_nr_elements or the max
array size based on element_size need not be changed.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The `parts' member of struct flex_array should evaluate to an incomplete
type so that sizeof() cannot be used and C99 does not require the
zero-length specification.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

flex_array_free_parts() does not take `src' or `element_nr' formals, so
remove their respective comments.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If all array elements fit into the base structure and data is copied using
flex_array_put() starting at a non-zero index, flex_array_get() will fail
to return the data.

This fixes the bug by only checking for NULL parts when all elements do
not fit in the base structure when flex_array_get() is used.  Otherwise,
fa_element_to_part_nr() will always be 0 since there are no parts
structures needed and such element may never have been put.  Thus, it will
remain NULL due to the kzalloc() of the base.

Additionally, flex_array_put() now only checks for a NULL part when all
elements do not fit in the base structure.  This is otherwise unnecessary
since the base structure is guaranteed to exist (or we would have already
hit a NULL pointer).
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix incorrect verdict check and returns error if device_create failed,
otherwise driver triggers kernel oops.

Signed-off-by: Joonwoo Park<joonwpark81@gmail.com>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ima_counts_get() calls ima_iint_find_insert_get() which takes a reference
to the iint in question, but does not put that reference at the end of the
function.  This can lead to a nasty memory leak.  Easy enough to reproduce:

#include <sys/mman.h>
#include <stdio.h>

int main (void)
{
	int i;
	void *ptr;

	for (i=0; i < 100000; i++) {
		ptr = mmap(NULL, 4096, PROT_READ|PROT_WRITE,
			   MAP_SHARED|MAP_ANONYMOUS, -1, 0);
		if (ptr == MAP_FAILED)
			return 2;
		munmap(ptr, 4096);
	}

	return 0;
}
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>

arch/m68k/include/asm/pgtable_mm.h:148:1: warning: "pgprot_noncached" redefined
In file included from arch/m68k/include/asm/pgtable_mm.h:138,
                 from arch/m68k/include/asm/pgtable.h:4,
                 from include/linux/mm.h:40,
                 from include/linux/pagemap.h:7,
                 from include/linux/blkdev.h:12,
                 from arch/m68k/emu/nfblock.c:17:
include/asm-generic/pgtable.h:133:1: warning: this is the location of the previous definition

pgprot_noncached() should be defined _before_ including asm-generic/pgtable.h
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

arch/m68k/include/asm/motorola_pgalloc.h: In function 'pte_alloc_one':
arch/m68k/include/asm/motorola_pgalloc.h:44: warning: passing argument 1 of 'kunmap' from incompatible pointer type

Also, remove unneeded test for kmap() failure.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

With the postfix decrement cnt reaches -1 rather than 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

With while (count++ < 50) { ...  } count can reach 51, not 50, so we
shouldn't give an error message on a count of 50.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

If we run out of memory, use keventd to fill the buffer.  There's a
report of this happening: "Page allocation failures in guest",
Message-ID: <20090713115158.0a4892b0@mjolnir.ossman.eu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  irda/sa1100_ir: fix broken netdev_ops conversion
  irda/au1k_ir: fix broken netdev_ops conversion
  pkt_sched: Fix bogon in tasklet_hrtimer changes.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Validate linear D-TLB misses.
  sparc64: Update defconfig.
  sparc32: Update defconfig.
  sparc32: Kill trap table freeing code.
  sparc: sys32.S incorrect compat-layer splice() system call
  sparc: Use page_fault_out_of_memory() for VM_FAULT_OOM.
  sparc64: Sign extend length arg to truncate syscalls when compat.
  sparc: Fix cleanup crash in bbc_envctrl_cleanup()