- 24 Feb, 2016 39 commits
-
-
Sumit Saxena authored
This patch will create a reply queue pool for each MSI-X index and will provide an array of base addresses instead of the single address of legacy mode. Using this new interface the driver can support higher queue depths through scattered DMA pools. If array mode is not supported driver will fall back to the legacy method of reply pool allocation. This limits controller queue depth to 1K max. To enable a queue depth of more than 1K driver requires firmware to support array mode and scratch_pad3 will provide the new queue depth value. When RDPQ is used, downgrading to an older firmware release should not be permitted. This may cause firmware fault and is not supported. Signed-off-by:
Kashyap Desai <kashyap.desai@avagotech.com> Signed-off-by:
Sumit Saxena <sumit.saxena@avagotech.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Sumit Saxena authored
Firmware will fill out per-LD data to tell driver whether a particular LD supports region lock bypass. If yes, then driver will send non-FP LDIO to region lock bypass FIFO. With this change in driver, firmware will optimize certain code to improve performance. Signed-off-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
-
Sumit Saxena authored
This patch will update device Queue depth based on interface type(SAS, SATA..) for sysPDs. For Virtual disks(VDs), there will be no change in queue depth (will remain 256). To fetch interface type (SAS or SATA or FC..) of syspD, driver will send DCMD MR_DCMD_PD_GET_INFO. Signed-off-by:
-
Sumit Saxena authored
This patch adds task management for SCSI commands. Added functions are task abort and target reset. 1. Currently, megaraid_sas driver performs controller reset when any IO times out. With task management support added, task abort and target reset will be tried to recover timed out IO. If task management fails, then controller reset will be performaned. If the task management request times out, fail the request and escalate to the next level (controller reset). 2. mr_device_priv_data will be allocated for all generations of controller, but is_tm_capable flag will never be set for controllers (prior to Invader series) as firmware support is not available for task management. 3. Task management capable firmware will set is_tm_capable flag in firmware API. Signed-off-by:
-
Sumit Saxena authored
Signed-off-by:
-
Sumit Saxena authored
This patch will do proper error handling for DCMD timeout failure cases for Fusion adapters: 1. For MFI adapters, in case of DCMD timeout (DCMD which must return SUCCESS) driver will call kill adapter. 2. What action needs to be taken in case of DCMD timeout is decided by function dcmd_timeout_ocr_possible(). DCMD timeout causing OCR is applicable to the following commands: MR_DCMD_PD_LIST_QUERY MR_DCMD_LD_GET_LIST MR_DCMD_LD_LIST_QUERY MR_DCMD_CTRL_SET_CRASH_DUMP_PARAMS MR_DCMD_SYSTEM_PD_MAP_GET_INFO MR_DCMD_LD_MAP_GET_INFO 3. If DCMD fails from driver init path there are certain DCMDs which must return SUCCESS. If those DCMDs fail, driver bails out. For optional DCMDs like pd_info etc., driver continues without executing certain functionality. Signed-off-by:
-
Sumit Saxena authored
This patch will do synhronization between OCR function and AEN function using "reset_mutex" lock. reset_mutex will be acquired only in the first half of the AEN function which issues a DCMD. Second half of the function which calls SCSI API (scsi_add_device/scsi_remove_device) should be out of reset_mutex to avoid deadlock between scsi_eh thread and driver. During chip reset (inside OCR function), there should not be any PCI access and AEN function (which is called in delayed context) may be firing DCMDs (doing PCI writes) when chip reset is happening in parallel which will cause FW fault. This patch will solve the problem by making AEN thread and OCR thread mutually exclusive. Signed-off-by:
-
Don Brace authored
The hpsa driver uses this function to cleanup inquiry data. Our new pqi driver will also use this function. This function was copied into both drivers. This patch exports sanitize_inquiry_string so the hpsa and the pqi drivers can use this function directly. Suggested-by:
Hannes Reinecke <hare@suse.de> Suggested-by: Matthew R. Ochs mrochs@linux.vnet.ibm.com Reviewed-by:
Kevin Barnett <kevin.barnett@pmcs.com> Reviewed-by:
Justin Lindley <justin.lindley@pmcs.com> Reviewed-by:
Scott Teel <scott.teel@pmcs.com> Reviewed-by:
Don Brace <don.brace@pmcs.com> Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
Himanshu Madhani <himanshu.madhani@qlogic.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by:
-
Chad Dupuis authored
If we fail to queue an srb for an async login we should set the relogin flag so it will be retried as the reason for the queuing failure was most likely transient. Failure to do this can lead to failed paths as login is never retried if the relogin flag is not set. Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Reviewed-by:
-
Harish Zunjarrao authored
Signed-off-by:
Harish Zunjarrao <harish.zunjarrao@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
-
Harish Zunjarrao authored
Signed-off-by:
-
Sawan Chandak authored
Signed-off-by:
Sawan Chandak <sawan.chandak@qlogic.com> Signed-off-by:
-
Sawan Chandak authored
Signed-off-by:
-
Himanshu Madhani authored
Set bit 12 of additional firmware options 3 to let firmware hold status IOCB until ABTS response is received from Target. Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Alexey Khoroshilov authored
hwi_write_buffer() does not check if mapping dma memory succeed. The patch adds the check and failure handling. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Reviewed-by:
Jitendra Bhivare <jitendra.bhivare@avagotech.com> Acked-by:
-
Jitendra Bhivare authored
Driver version: 11.0.0.0 Signed-off-by:
-
Jitendra Bhivare authored
Login/Logout loop was hanging after few hours. /var/log/message showed that alloc_wrb_handle() function was not able to allocate any new WRB. Sep 11 11:25:22 Jhelum10 kernel: connection32513:0: Could not send nopout Sep 11 11:25:22 Jhelum10 kernel: scsi host10: BM_4989 : Alloc of WRB_HANDLE Failed for the CID : 384 Sep 11 11:25:22 Jhelum10 kernel: connection32513:0: Could not allocate pdu for mgmt task. Driver allocates WRB to pass login negotiated parameters information to FW in beiscsi_offload_connection(). This allocated WRB was not freed so there was WRB_Leak happening. Put WRB used for posting the login-negotiated parameters back in pool. Signed-off-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Jitendra Bhivare authored
Use only port_link_status only to determine link state change. Only bit 0 is used to get the state. Remove code for processing port_fault. Fixed get_nic_conf structure definition. Removed rsvd[23] field in be_cmd_get_nic_conf_resp. Moved definitions of struct field values below the field. Signed-off-by:
-
Jitendra Bhivare authored
Async link event provides port_speed info. Cache the port_speed info and use the same to report in ISCSI_HOST_PARAM_PORT_SPEED query. Removed link status query IOCTL used to do the same. Signed-off-by:
-
Jitendra Bhivare authored
iscsi_port_speed and iscsi_port_speed_names have new entries for 25Gbps and 40Gbps link speeds. Signed-off-by:
-
Jitendra Bhivare authored
OS not responding when running 2 port traffic on 72 CPUs system. be2iscsi IRQs gets affined to CPU0 when irqbalancer is disabled. be_iopoll processing completions in BLOCK_IOPOLL_SOFTIRQ hogged CPU0. 1. Use budget to exit the polling loop. beiscsi_process_cq didn't honour it. 2. Rearming of EQ is done only after iopoll completes. [mkp: Fixed up blk_iopoll -> irq_poll transition] Signed-off-by:
-
Jitendra Bhivare authored
Change return value of completed MCC EBUSY to EINVAL. Signed-off-by:
-
Jitendra Bhivare authored
System crash in I+T card personality. Fix to add validation for ULP in initiator mode, physical port number, and supported queue, icd, cid counts. Signed-off-by:
-
Jitendra Bhivare authored
Log messages for misconfigured transceivers reported by FW. Register async events that driver handles using MCC_CREATE_EXT ioctl. Errors messages for faulted/uncertified/unqualified optics are logged. Added IOCTL to get port_name to be displayed in error message. Signed-off-by:
-
Jitendra Bhivare authored
Configuring VLAN parameters through IPv6 interface was not supported in driver. Signed-off-by:
-
Jitendra Bhivare authored
Null pointer dereference in shutdown path after taking dump. Shutdown path is not needed as FW comes up clean every time during probe after issuing FUNCTION reset MBOX command. Signed-off-by:
-
Jitendra Bhivare authored
Use of mutex_lock_interruptible can return -EINTR, handle and log the error. Signed-off-by:
-
Jitendra Bhivare authored
FW recommended timeout for all mbox command is 30s. Use msleep instead mdelay to relinquish CPU when polling for mbox completion. Signed-off-by:
-
Jitendra Bhivare authored
alloc_mcc_tag needs to be done under mcc_lock. Signed-off-by:
-
Jitendra Bhivare authored
beiscsi_mccq_compl sets MCC_TAG_STATE_TIMEOUT before setting up tag_mem_state. be_mcc_compl_process_isr checks for MCC_TAG_STATE_TIMEOUT first then accesses tag_mem_state which might be still getting populated in the process context. Fix: Set MCC_TAG_STATE_TIMEOUT after tag_mem_state is populated. Removed MCC_TAG_STATE_COMPLETED. When posted its in running state and the running state is cleared in be_mcc_compl_process_isr. be_mcc_notify now takes tag argument to set it to running state. Use bit operations for tag_state. Use barriers before setting the state. Signed-off-by:
-
Jitendra Bhivare authored
This is second part of actual fix for soft lockup. All mbox cmds issued using BMBX and MCC are synchronized using mutex mbox_lock instead of spin_lock. Used mutex_lock_interruptible where ever possible. Signed-off-by:
Shane Seymour <shane.seymour@hpe.com> Reviewed-by:
-
Jitendra Bhivare authored
We are taking mbox_lock spinlock which disables pre-emption before we poll for mbox completion. Waiting there with spinlock held in excess of 20s will cause soft lockup. Actual fix is to change mbox_lock to mutex. The changes are done in phases. This is the first part. 1. Changed mgmt_get_all_if_id to use MCC where after posting lock is released. 2. Changed be_mbox_db_ready_wait to busy wait for 12s max and removed wait_event_timeout. Added error handling code for IO reads. OPCODE_COMMON_QUERY_FIRMWARE_CONFIG mbox command takes 8s time when unreachable boot targets configured. Signed-off-by:
-
git://git.linux-nfs.org/projects/trondmy/linux-nfsLinus Torvalds authored
Pull NFS client bugfixes from Trond Myklebust: "Stable bugfixes: - Fix nfs_size_to_loff_t - NFSv4: Fix a dentry leak on alias use Other bugfixes: - Don't schedule a layoutreturn if the layout segment can be freed immediately. - Always set NFS_LAYOUT_RETURN_REQUESTED with lo->plh_return_iomode - rpcrdma_bc_receive_call() should init rq_private_buf.len - fix stateid handling for the NFS v4.2 operations - pnfs/blocklayout: fix a memeory leak when using,vmalloc_to_page - fix panic in gss_pipe_downcall() in fips mode - Fix a race between layoutget and pnfs_destroy_layout - Fix a race between layoutget and bulk recalls" * tag 'nfs-for-4.5-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: NFSv4.x/pnfs: Fix a race between layoutget and bulk recalls NFSv4.x/pnfs: Fix a race between layoutget and pnfs_destroy_layout auth_gss: fix panic in gss_pipe_downcall() in fips mode pnfs/blocklayout: fix a memeory leak when using,vmalloc_to_page nfs4: fix stateid handling for the NFS v4.2 operations NFSv4: Fix a dentry leak on alias use xprtrdma: rpcrdma_bc_receive_call() should init rq_private_buf.len pNFS: Always set NFS_LAYOUT_RETURN_REQUESTED with lo->plh_return_iomode pNFS: Fix pnfs_mark_matching_lsegs_return() nfs: fix nfs_size_to_loff_t -
Linus Torvalds authored
In commit 11f1a4b9 ("x86: reorganize SMAP handling in user space accesses") I changed how the stac/clac instructions were generated around the user space accesses, which then made it possible to do batched accesses efficiently for user string copies etc. However, in doing so, I completely spaced out, and didn't even think about the 32-bit case. And nobody really even seemed to notice, because SMAP doesn't even exist until modern Skylake processors, and you'd have to be crazy to run 32-bit kernels on a modern CPU. Which brings us to Andy Lutomirski. He actually tested the 32-bit kernel on new hardware, and noticed that it doesn't work. My bad. The trivial fix is to add the required uaccess begin/end markers around the raw accesses in <asm/uaccess_32.h>. I feel a bit bad about this patch, just because that header file really should be cleaned up to avoid all the duplicated code in it, and this commit just expands on the problem. But this just fixes the bug without any bigger cleanup surgery. Reported-and-tested-by:
Andy Lutomirski <luto@kernel.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
- 22 Feb, 2016 1 commit
-
-
Trond Myklebust authored
Replace another case where the layout 'plh_block_lgets' can trigger infinite loops in send_layoutget(). Signed-off-by:Trond Myklebust <trond.myklebust@primarydata.com>
-
