R-Car Gen3 needs to enable clocks of both host and peripheral.
Otherwise, other side device cannot work correctly. So, this patch
adds a property of clock-names for R-Car Gen3 as an optional.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

R-Car Gen3 needs to deassert resets of both host and peripheral.
Since [eo]hci-platform is possible to assert the reset(s) when
the probing failed, renesas_usbhs driver doesn't work correctly
regardless of finished probing. To fix this issue, this patch adds
reset_control on this renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.

Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.

DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When using external vbus supply regulator, it should be enabled
synchronously with PWR bit in HPRT register. This also fixes
unbalanced use of this optional regulator (This can be reproduced
easily when unbinding the driver).

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dwc2_vbus_supply_exit() may call regulator_disable(). It shouldn't be
called with interrupts disabled as it might sleep.
This is seen with DEBUG_ATOMIC_SLEEP=y.

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There's a race with root hub resume, when using external vbus supply.
Root hub gets resumed, but runtime pm autosuspend runs as external vbus
supply isn't enabled. So, host never exit from power down properly.
Initialize vbus external supply before, rater that after hub resume.

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Move devm_regulator_get_optional() call to probe routine. This avoids
'vbus-supply' regulator to be requested lots of times, upon each call
to dwc2_vbus_supply_init(), e.g. like with runtime pm.

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Like the omap back-end, we get a link error with CONFIG_EXTCON=m
when building the qcom back-end into the kernel:

drivers/usb/dwc3/dwc3-qcom.o: In function `dwc3_qcom_probe':
dwc3-qcom.c:(.text+0x13dc): undefined reference to `extcon_get_edev_by_phandle'
dwc3-qcom.c:(.text+0x1b18): undefined reference to `devm_extcon_register_notifier'
dwc3-qcom.c:(.text+0x1b9c): undefined reference to `extcon_get_state'

Do the same thing as OMAP and add an explicit dependency on
EXTCON.

Fixes: a4333c3a ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The at91sam9rl PMC is not quite the same as the at91sam9g45 one and now has
its own compatible string. Add support for that.

Fixes: 217bace8e548 ("ARM: dts: fix PMC compatible")
Acked-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The driver may sleep in an interrupt handler.
The function call path (from bottom to top) in Linux-4.17 is:

[FUNC] fotg210_ep_queue(GFP_KERNEL)
drivers/usb/gadget/udc/fotg210-udc.c, 744:
	fotg210_ep_queue in fotg210_get_status
drivers/usb/gadget/udc/fotg210-udc.c, 768:
	fotg210_get_status in fotg210_setup_packet
drivers/usb/gadget/udc/fotg210-udc.c, 949:
	fotg210_setup_packet in fotg210_irq (interrupt handler)

To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
If possible, spin_unlock() and spin_lock() around fotg210_ep_queue()
can be also removed.

This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Disabling all EP's allow to reset EP's to initial state.
On disconnect disable all EP's instead of just killing
all requests. Because of some platform didn't catch
disconnect event, same stuff added to
dwc2_hsotg_core_init_disconnected() function when USB
reset detected on the bus.

Changed from version 1:
Changed lock acquire flow in dwc2_hsotg_ep_disable()
function.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

DWC3 variant found in Exynos5433 SoCs requires keeping all DRD30/UHOST30
clocks enabled all the time the driver does any access to DWC3 registers,
otherwise external abort happens. So far DWC3 hardware module worked with
samsung,exynos5250-dwusb3 compatible only by luck when built into kernel:
all DRD30 clocks were left enabled by bootloader and later kept enabled
by the DRD PHY driver. However, if one tried to use Exnos DWC3 driver as
a module or performed system suspend/resume cycle, external abort
happened. This patch finally fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add per-variant list of clocks and manage them all together in
the single array. This is a preparation for adding new variants
of Exynos SoCs. No functional changes for existing Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

All supported Exynos variants provide respective generic PHY framework
based drivers for controlling USB PHYs, so there is no point
creating fake USB PHYs based on platform devices. While removing useless
code, remove calls to runtime PM, which have no effect.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Trivial fix to spelling mistake in dev_dbg message
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Clang warns when multiple pairs of parentheses are used for a single
conditional statement.

drivers/usb/gadget/udc/mv_udc_core.c:188:33: warning: equality
comparison with extraneous parentheses [-Wparentheses-equality]
        while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
                ~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
drivers/usb/gadget/udc/mv_udc_core.c:188:33: note: remove extraneous
parentheses around the comparison to silence this warning
        while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
               ~                       ^                  ~
drivers/usb/gadget/udc/mv_udc_core.c:188:33: note: use '=' to turn this
equality comparison into an assignment
        while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
                                       ^~
                                       =
1 warning generated.

Link: https://github.com/ClangBuiltLinux/linux/issues/120Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch removes a set but unused variable in hcd.c.

Fixes gcc warning:
variable ‘data_fifo’ set but not used [-Wunused-but-set-variable]
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Joshua Abraham <j.abraham1776@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This reverts commit 8ada211d.

R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
In other words, like other R-Car Gen3 SoCs, R-Car D3 can change the mode
by using the phy-rcar-gen3-usb2 driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Trivial fix to spelling mistakes in debug warning messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

UVC gadget updates for v4.20

- configfs cleanups, fixes and extensions
- Endianness fixes
- Miscellaneous cleanups

Miguel writes:
  "A trivial fix for auxdisplay

    - MAINTAINERS reference fix for moved file
      Reported by Joe Perches"

* tag 'auxdisplay-for-greg-v4.19-rc6' of https://github.com/ojeda/linux:
  MAINTAINERS: fix reference to moved drivers/{misc => auxdisplay}/panel.c

Merge tag 'libnvdimm-fixes2-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm

Dan writes:
  "filesystem-dax for 4.19-rc6

   Fix a deadlock in the new for 4.19 dax_lock_mapping_entry() routine."

* tag 'libnvdimm-fixes2-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  dax: Fix deadlock in dax_lock_mapping_entry()

Commit 51c1e9b5 ("auxdisplay: Move panel.c to drivers/auxdisplay folder")
moved the file, but the MAINTAINERS reference was not updated.

Link: https://lore.kernel.org/lkml/20180928220131.31075-1-joe@perches.com/Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>

Jens writes:
  "Block fixes for 4.19-rc6

   A set of fixes that should go into this release. This pull request
   contains:

   - A fix (hopefully) for the persistent grants for xen-blkfront. A
     previous fix from this series wasn't complete, hence reverted, and
     this one should hopefully be it. (Boris Ostrovsky)

   - Fix for an elevator drain warning with SMR devices, which is
     triggered when you switch schedulers (Damien)

   - bcache deadlock fix (Guoju Fang)

   - Fix for the block unplug tracepoint, which has had the
     timer/explicit flag reverted since 4.11 (Ilya)

   - Fix a regression in this series where the blk-mq timeout hook is
     invoked with the RCU read lock held, hence preventing it from
     blocking (Keith)

   - NVMe pull from Christoph, with a single multipath fix (Susobhan Dey)"

* tag 'for-linus-20180929' of git://git.kernel.dk/linux-block:
  xen/blkfront: correct purging of persistent grants
  Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
  blk-mq: I/O and timer unplugs are inverted in blktrace
  bcache: add separate workqueue for journal_write to avoid deadlock
  xen/blkfront: When purging persistent grants, keep them in the buffer
  block: fix deadline elevator drain for zoned block devices
  blk-mq: Allow blocking queue tag iter callbacks
  nvme: properly propagate errors in nvme_mpath_init

Thomas writes:
  "A single fix for the AMD memory encryption boot code so it does not
   read random garbage instead of the cached encryption bit when a kexec
   kernel is allocated above the 32bit address limit."

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot: Fix kexec booting failure in the SEV bit detection code

Thomas writes:
  "Three small fixes for clocksource drivers:
   - Proper error handling in the Atmel PIT driver
   - Add CLOCK_SOURCE_SUSPEND_NONSTOP for TI SoCs so suspend works again
   - Fix the next event function for Facebook Backpack-CMM BMC chips so
     usleep(100) doesnt sleep several milliseconds"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/timer-atmel-pit: Properly handle error cases
  clocksource/drivers/fttmr010: Fix set_next_event handler
  clocksource/drivers/ti-32k: Add CLOCK_SOURCE_SUSPEND_NONSTOP flag for non-am43 SoCs

Thomas writes:
  "A single fix for a missing sanity check when a pinned event is tried
  to be read on the wrong CPU due to a legit event scheduling failure."

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Add sanity check to deal with pinned event failure

Rafael writes:
  "Power management fix for 4.19-rc6

   Fix incorrect __init and __exit annotations in the Qualcomm
   Kryo cpufreq driver (Nathan Chancellor)."

* tag 'pm-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: qcom-kryo: Fix section annotations

There is currently a warning when building the Kryo cpufreq driver into
the kernel image:

WARNING: vmlinux.o(.text+0x8aa424): Section mismatch in reference from
the function qcom_cpufreq_kryo_probe() to the function
.init.text:qcom_cpufreq_kryo_get_msm_id()
The function qcom_cpufreq_kryo_probe() references
the function __init qcom_cpufreq_kryo_get_msm_id().
This is often because qcom_cpufreq_kryo_probe lacks a __init
annotation or the annotation of qcom_cpufreq_kryo_get_msm_id is wrong.

Remove the '__init' annotation from qcom_cpufreq_kryo_get_msm_id
so that there is no more mismatch warning.

Additionally, Nick noticed that the remove function was marked as
'__init' when it should really be marked as '__exit'.

Fixes: 46e2856b (cpufreq: Add Kryo CPU scaling driver)
Fixes: 5ad7346b (cpufreq: kryo: Add module remove and exit)
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.18+ <stable@vger.kernel.org> # 4.18+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Christoph writes:
  "dma mapping fix for 4.19-rc6

   fix a missing Kconfig symbol for commits introduced in 4.19-rc"

* tag 'dma-mapping-4.19-3' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: add the missing ARCH_HAS_SYNC_DMA_FOR_CPU_ALL declaration

Dmitry writes:
  "Input updates for v4.19-rc5

   Just a few driver fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: uinput - allow for max == min during input_absinfo validation
  Input: elantech - enable middle button of touchpad on ThinkPad P72
  Input: atakbd - fix Atari CapsLock behaviour
  Input: atakbd - fix Atari keymap
  Input: egalax_ts - add system wakeup support
  Input: gpio-keys - fix a documentation index issue

Mark writes:
  "spi: Fixes for v4.19

   Quite a few fixes for the Renesas drivers in here, plus a fix for the
   Tegra driver and some documentation fixes for the recently added
   spi-mem code.  The Tegra fix is relatively large but fairly
   straightforward and mechanical, it runs on probe so it's been
   reasonably well covered in -next testing."

* tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: spi-mem: Move the DMA-able constraint doc to the kerneldoc header
  spi: spi-mem: Add missing description for data.nbytes field
  spi: rspi: Fix interrupted DMA transfers
  spi: rspi: Fix invalid SPI use during system suspend
  spi: sh-msiof: Fix handling of write value for SISTR register
  spi: sh-msiof: Fix invalid SPI use during system suspend
  spi: gpio: Fix copy-and-paste error
  spi: tegra20-slink: explicitly enable/disable clock

Merge tag 'regulator-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Mark writes:
  "regulator: Fixes for 4.19

   A collection of fairly minor bug fixes here, a couple of driver
   specific ones plus two core fixes.  There's one fix for the new
   suspend state code which fixes some confusion with constant values
   that are supposed to indicate noop operation and another fixing a
   race condition with the creation of sysfs files on new regulators."

* tag 'regulator-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: fix crash caused by null driver data
  regulator: Fix 'do-nothing' value for regulators without suspend state
  regulator: da9063: fix DT probing with constraints
  regulator: bd71837: Disable voltage monitoring for LDO3/4

Michael writes:
  "powerpc fixes for 4.19 #3

   A reasonably big batch of fixes due to me being away for a few weeks.

   A fix for the TM emulation support on Power9, which could result in
   corrupting the guest r11 when running under KVM.

   Two fixes to the TM code which could lead to userspace GPR corruption
   if we take an SLB miss at exactly the wrong time.

   Our dynamic patching code had a bug that meant we could patch freed
   __init text, which could lead to corrupting userspace memory.

   csum_ipv6_magic() didn't work on little endian platforms since we
   optimised it recently.

   A fix for an endian bug when reading a device tree property telling
   us how many storage keys the machine has available.

   Fix a crash seen on some configurations of PowerVM when migrating the
   partition from one machine to another.

   A fix for a regression in the setup of our CPU to NUMA node mapping
   in KVM guests.

   A fix to our selftest Makefiles to make them work since a recent
   change to the shared Makefile logic."

* tag 'powerpc-4.19-3' of https://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  selftests/powerpc: Fix Makefiles for headers_install change
  powerpc/numa: Use associativity if VPHN hcall is successful
  powerpc/tm: Avoid possible userspace r1 corruption on reclaim
  powerpc/tm: Fix userspace r13 corruption
  powerpc/pseries: Fix unitialized timer reset on migration
  powerpc/pkeys: Fix reading of ibm, processor-storage-keys property
  powerpc: fix csum_ipv6_magic() on little endian platforms
  powerpc/powernv/ioda2: Reduce upper limit for DMA window size (again)
  powerpc: Avoid code patching freed init sections
  KVM: PPC: Book3S HV: Fix guest r11 corruption with POWER9 TM workarounds

Linus writes:
  "Pin control fixes for v4.19:
   - Fixes to x86 hardware:
   - AMD interrupt debounce issues
   - Faulty Intel cannonlake register offset
   - Revert pin translation IRQ locking"

* tag 'pinctrl-v4.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  Revert "pinctrl: intel: Do pin translation when lock IRQ"
  pinctrl: cannonlake: Fix HOSTSW_OWN register offset of H variant
  pinctrl/amd: poll InterruptEnable bits in amd_gpio_irq_set_type

It is possible that a failure can occur during the scheduling of a
pinned event. The initial portion of perf_event_read_local() contains
the various error checks an event should pass before it can be
considered valid. Ensure that the potential scheduling failure
of a pinned event is checked for and have a credible error.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: fenghua.yu@intel.com
Cc: tony.luck@intel.com
Cc: acme@kernel.org
Cc: gavin.hindman@intel.com
Cc: jithu.joseph@intel.com
Cc: dave.hansen@intel.com
Cc: hpa@zytor.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/6486385d1f30336e9973b24c8c65f5079543d3d3.1537377064.git.reinette.chatre@intel.com

Dave writes:
  "drm fixes for 4.19-rc6

   Looks like a pretty normal week for graphics,

   core: syncobj fix, panel link regression revert
   amd: suspend/resume fixes, EDID emulation fix
   mali-dp: NV12 writeback and vblank reset fixes
   etnaviv: DMA setup fix"

* tag 'drm-fixes-2018-09-28' of git://anongit.freedesktop.org/drm/drm:
  drm/amd/display: Fix Edid emulation for linux
  drm/amd/display: Fix Vega10 lightup on S3 resume
  drm/amdgpu: Fix vce work queue was not cancelled when suspend
  Revert "drm/panel: Add device_link from panel device to DRM device"
  drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
  drm/malidp: Fix writeback in NV12
  drm: mali-dp: Call drm_crtc_vblank_reset on device init
  drm/etnaviv: add DMA configuration for etnaviv platform device

Merge tag 'riscv-for-linus-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux

Palmer writes:
  "A Single RISC-V Update for 4.19-rc6

   The Debian guys have been pushing on our port and found some
   unversioned symbols leaking into modules.  This PR contains a single
   fix for that issue."

* tag 'riscv-for-linus-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
  RISC-V: include linux/ftrace.h in asm-prototypes.h

Bjorn writes:
  "PCI fixes:

  - Fix ACPI hotplug issue that causes black screen crash at boot (Mika
    Westerberg)

  - Fix DesignWare "scheduling while atomic" issues (Jisheng Zhang)

  - Add PPC contacts to MAINTAINERS for PCI core error handling (Bjorn
    Helgaas)

  - Sort Mobiveil MAINTAINERS entry (Lorenzo Pieralisi)"

* tag 'pci-v4.19-fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
  PCI: dwc: Fix scheduling while atomic issues
  MAINTAINERS: Move mobiveil PCI driver entry where it belongs
  MAINTAINERS: Update PPC contacts for PCI core error handling