- 22 Jul, 2014 10 commits
-
-
Christophe Ricard authored
Support for Initiator and Target mode with ISO18092 commands support: - ATR_REQ/ATR_RES - PSL_REQ/PSL_RES - DEP_REQ/DEP_RES Work based on net/nfc/digital_dep.c. st21nfca is using: - Gate reader F for P2P in initiator mode. - Gate card F for P2P in target mode. Felica tag and p2p are differentiated with NFCID2. When starting with 01FE it is acting in p2p mode. On complete_target_discovered on ST21NFCA_RF_READER_F_GATE supported_protocols is set to NFC_PROTO_NFC_DEP_MASK for P2P. Tested against: Nexus S, Galaxy S2, Galaxy S3, Galaxy S3 Mini, Nexus 4 & Nexus 5. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
Send DM_DISCONNECT command to disconnect Terminal Host from the HCI network. - The persistent states of the terminal host pipes, including registry values, are not modifies. Therefore, there is no NVRAM update to disconnect the terminal host. - The terminal host RF card gates are disabled which means that there will be no event related to card RF gates until communication has been restored. - The terminal host RF reader request is reset so the RF reader polling for terminal host is disabled. To restore the communication, the terminal host can send any HCI command or event. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
stop_poll allows to stop CLF reader polling. Some other operations might be necessary for some CLF to stop polling. For example in card mode. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
A DEP_RES with a SUPERVISOR PDU can be up to 16 bytes long. In order to avoid useless read during p2p, extend first read sequence to 16 and reduce third sequence to 12 to keep same total on the full sequence. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
A start of frame is 7E 00 not only 7E. Make sure the first read sequence is starting with 7E 00. For example: 7E FF FF FF FF is as a correct crc but it is a bad frame. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
In case no data are retrieve through i2c or one specific case is not handled. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
Add T1T matching with Jewel during notification. It was causing "the target found does not have the desired protocol" to show up. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
Describe the properties used by the st21nfcb NFC controller driver. Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Christophe Ricard authored
Add driver for STMicroelectronics ST21NFCB NFC controller. ST21NFCB is using NCI protocol and a proprietary low level transport protocol called NDLC used on top. NDLC: The protocol defines 2 types of frame: - One type carrying NCI data (referred as DATAFRAME frames). - One type carrying protocol information used for flow control and error control mechanisms (referred as SUPERVISOR frames). After each frame transmission to the NFC controller, the device host SHALL waitfor an ACK (SUPERVISOR frame) reception before sending a new frame. The NFC controller MAY send a frame at anytime to the device host. The NFC controller MAY send a specific WAIT supervisor frame to indicate to device host that a NCI data packet has been received but that it could take significant time before the NFC controller sends an ACK and thus allows next data reception. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
- 20 Jul, 2014 3 commits
-
-
Mark A. Greer authored
Add new "NFC_DIGITAL_FRAMING_*" calls to the digital layer so the driver can make the necessary adjustments when performing anticollision while in target mode. The driver must ensure that the effect of these calls happens after the following response has been sent but before reception of the next request begins. Acked-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
Currently, digital_target_found() has a race between the events started by calling nfc_targets_found() (which ultimately expect ddev->poll_tech_count to be zero) and setting ddev->poll_tech_count to zero after the call to nfc_targets_found(). When the race is "lost" (i.e., ddev->poll_tech_count is found to not be zero by the events started by nfc_targets_found()), an error message is printed and the target is not found. A similar race exists when digital_tg_recv_atr_req() calls nfc_tm_activated(). Fix this by first saving the current value of ddev->poll_tech_count and then clearing it before calling nfc_targets_found()/nfc_tm_activated(). Clearing ddev->poll_tech_count before calling nfc_targets_found()/nfc_tm_activated() eliminates the race. Saving the value is required so it can be restored when nfc_targets_found()/nfc_tm_activated() fails and polling needs to continue. Acked-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
Mark A. Greer authored
In digital_in_recv_sel_res(), the code that determines the tag type will interpret bits 7:6 (lsb being b1 as per the Digital Specification) of a SEL RES set to 11b as a Type 4 tag. This is okay except that the neard will interpret the same value as an NFC-DEP device (in src/tag.c:set_tag_type() in the neard source). Make the digital layer's interpretation match neard's interpretation by changing the order of the checks in digital_in_recv_sel_res() so that a value of 11b in bits 7:6 is interpreted as an NFC-DEP device instead of a Type 4 tag. Acked-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-
- 18 Jul, 2014 24 commits
-
-
Bing Zhao authored
We don't need wall-clock time here, and in most configurations that care, there are already timestamps in the kernel using CONFIG_PRINTK_TIME=y. Reported-by: Paul Stewart <pstew@chromium.org> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ujjal Roy authored
In managed mode if the driver is getting a re-associate command from cfg80211, driver deauthenticates with the AP internally and sends a disconnected event to cfg80211 before completion of its association process. The disconnected event then modifies the SSID length as wdev->ssid_len = 0. So, upon receiving the connect result event from driver, cfg80211 is unable to get that BSS from the device's BSS list and generates the following WARN_ON message. WARNING: CPU: 0 PID: 857 at net/wireless/sme.c:658 __cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]() Avoid re-association while the device is already associated to a network. Also remove the internal deauthentication from the association path. Signed-off-by: Ujjal Roy <royujjal@gmail.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Avinash Patil authored
This local variable is not used anywhere in function. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
By the way add few chipsets that were tracked with "wl" dumps. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Seems to be required by some hardware, wl does it every time. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Values were written to wrong registers. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Andrey Utkin authored
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80471 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80481Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Lorenzo Bianconi authored
Set up tx power for each MRR segment in the tx descriptor Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Packets originally buffered for the regular hardware tx queues can end up being transmitted through the U-APSD queue (via PS-Poll or U-APSD). When packets are dropped due to retransmit failures, the pending frames counter is not always updated properly. Fix this by keeping track of the queue that a frame was accounted for in the ath_frame_info struct, and using that on completion to decide whether the counter should be updated. This fixes some spurious transmit queue hangs. Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Just like in case of SSB SPROMs they are encoded in a bit tricky way. SPROM struct already uses s8 type and it's supposed to store decoded values. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
This is needed to properly handle early 802.11n devices like BCM4321. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vladimir Kondratiev authored
New register area defined in the firmware Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vladimir Kondratiev authored
Firmware sets this register with the offset of the firmware trace area within the peripheral memory region. Critical for the firmware trace to work Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vladimir Kondratiev authored
Use single data source for all information regarding the firmware memory map. With this change "ucode_xxx" regions disappears since they are in fact part of larger "upper area" region Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vladimir Kondratiev authored
If copy_from_user() fails, buffer allocated for parameters would leak Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vladimir Kondratiev authored
Variable 'ctx' declarad again in the inner loop. Should use one from outer loop instead. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vladimir Kondratiev authored
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vladimir Kondratiev authored
New hardware release appears; it require some changes to properly support it. Introduce struct wil_board and "board" attribute in wil6210_priv; keep hardware variant information in this structure. fill it on probe(). Used in the reset flow. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
-
John W. Linville authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
-
- 16 Jul, 2014 1 commit
-
-
Bing Zhao authored
The unwanted frame types are already handled in 'default' case of the switch/case below. The str_ptr is allocated but it can be leaked if the length check fails in the REQUEST/RESP cases. Fix it by allocating sta_ptr after the length checks. Reported-by: Paul Stewart <pstew@chromium.org> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Paul Stewart <pstew@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 15 Jul, 2014 2 commits
-
-
Rafał Miłecki authored
They are encoded the same way as in older SPROMs. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-