Add display support on the stm32f469-disco board.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

In the stm32f4 family, mipi dsi is only supported on stm32f469.
So add a new stm32f469 dtsi file & add mipi dsi support inside.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Use gpio bindings for vcc5v_otg.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Since commit 83a86fbb ("irqchip/gic: Loudly complain about
the use of IRQ_TYPE_NONE"), a warning is raised if IRQ_TYPE_NONE is used.
So we use IRQ_TYPE_LEVEL_HIGH for usart nodes instead of IRQ_TYPE_NONE.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@st.com>

Fix DTC warnings for stm32mp157:

Warning (unit_address_vs_reg): /soc/pin-controller: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /soc/pin-controller/uart4@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/pin-controller-z: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch adds flash nor on qspi. Each flash is
connected in quad mode and has its own chip select.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch adds qspi support on stm32mp157c,
read in memory mapped, write in indirect mode.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch enables cec node on stm32mp157c-ev1 board
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch adds cec support on stm32mp157c eval board.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add cec support on stm32mp157c
Signed-off-by: yannick fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add support for USBH (USB Host) to STM32MP157C SoC.
USBH is a USB Host controller supporting the standard registers used for
full- and low-speed (OHCI controller) and high-speed (EHCI controller).
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>

This patch enables USBPHYC (USB PHY Controller) on stm32mp157c-ev1.
This enables the two usbphyc usb2 ports.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

USBPHYC ports require 3 supplies: 3v3, 1v1 and 1v8.
This patch adds the corresponding properties to usbphyc ports on
stm32mp157c-ed1 board.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add support for USBPHYC (USB PHY Controller) to STM32MP157C SoC.
It manages two usb2 ports.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add dsi support on stm32mp157c
Signed-off-by: yannick fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add support for the display controller ltdc.
Signed-off-by: yannick fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add I2C1/5 support for STM32MP157C evaluation daughter on evaluation
mother board.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add I2C4 support for STM32MP157C evaluation daughter.
Required for PMIC.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch adds pins groups for I2C1,2,4 & 5
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch adds all STM32F7 I2C instances for STM32MP157C SoC.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch add CRC instance of the stm32mp157c SoC
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch add CRYP instance of the stm32mp157c SoC
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Enable stm32-hwrng for ed1 and ev1 boards
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch add RNG instance of the stm32mp157c SoC
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Activate MDMA for STM32MP157C
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Activate DMAMUX for STM32MP157C
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Activate DMAv2 for STM32MP157C
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add support for DAC (Digital to Analog Converter) to STM32MP157C.
STM32MP157C DAC has two output channels.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch adds reset binding file.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add LPtimer definitions, depending on features they provide:
- lptimer1 & 2 can act as PWM, trigger and encoder/counter
- lptimer3 can act as PWM and trigger
- lptimer4 & 5 can act as PWM
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

stm32mp157c has vrefbuf regulator that can provide analog reference
voltage from 1500mV to 2500mV.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Enable timer 6 on stm32mp157c-ed1 that can serve as trigger for
ADC for instance.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

stm32mp157c evaluation board has TIM2_CH4, TIM8_CH4 and TIM12_CH1
available on GPIO expansion connector.
Add PWM and associated triggers (for ADC/DAC) on these timers.
Keep them disabled so these pins can be used as GPIOs by default.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

stm32mp157c evaluation board has following PWM pins available on GPIO
expansion connector:
- TIM2_CH4 (PA3)
- TIM8_CH4 (PI2)
- TIM12_CH1 (PH6)
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add PWM and trigger support to stm32mp157c.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch enables stm32mp1 clock driver.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Pull more btrfs updates from David Sterba:
 "We have queued a few more fixes (error handling, log replay,
  softlockup) and the rest is SPDX updates that touche almost all files
  so the diffstat is long"

* tag 'for-4.17-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: Only check first key for committed tree blocks
  btrfs: add SPDX header to Kconfig
  btrfs: replace GPL boilerplate by SPDX -- sources
  btrfs: replace GPL boilerplate by SPDX -- headers
  Btrfs: fix loss of prealloc extents past i_size after fsync log replay
  Btrfs: clean up resources during umount after trans is aborted
  btrfs: Fix possible softlock on single core machines
  Btrfs: bail out on error during replay_dir_deletes
  Btrfs: fix NULL pointer dereference in log_dir_items

Pull cifs fixes from Steve French:
 "SMB3 fixes, a few for stable, and some important cleanup work from
  Ronnie of the smb3 transport code"

* tag '4.17-rc1SMB3-Fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: change validate_buf to validate_iov
  cifs: remove rfc1002 hardcoded constants from cifs_discard_remaining_data()
  cifs: Change SMB2_open to return an iov for the error parameter
  cifs: add resp_buf_size to the mid_q_entry structure
  smb3.11: replace a 4 with server->vals->header_preamble_size
  cifs: replace a 4 with server->vals->header_preamble_size
  cifs: add pdu_size to the TCP_Server_Info structure
  SMB311: Improve checking of negotiate security contexts
  SMB3: Fix length checking of SMB3.11 negotiate request
  CIFS: add ONCE flag for cifs_dbg type
  cifs: Use ULL suffix for 64-bit constant
  SMB3: Log at least once if tree connect fails during reconnect
  cifs: smb2pdu: Fix potential NULL pointer dereference

Pull SCSI fixes from James Bottomley:
 "This is a set of minor (and safe changes) that didn't make the initial
  pull request plus some bug fixes.

  The status handling code is actually a running regression from the
  previous merge window which had an incomplete fix (now reverted) and
  most of the remaining bug fixes are for problems older than the
  current merge window"

[ Side note: this merge also takes the base kernel git repository to 6+
  million objects for the first time. Technically we hit it a couple of
  merges ago already if you count all the tag objects, but now it
  reaches 6M+ objects reachable from HEAD.

  I was joking around that that's when I should switch to 5.0, because
  3.0 happened at the 2M mark, and 4.0 happened at 4M objects. But
  probably not, even if numerology is about as good a reason as any.

                                                              - Linus ]

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: devinfo: Add Microsoft iSCSI target to 1024 sector blacklist
  scsi: cxgb4i: silence overflow warning in t4_uld_rx_handler()
  scsi: dpt_i2o: Use after free in I2ORESETCMD ioctl
  scsi: core: Make scsi_result_to_blk_status() recognize CONDITION MET
  scsi: core: Rename __scsi_error_from_host_byte() into scsi_result_to_blk_status()
  Revert "scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()"
  scsi: aacraid: Insure command thread is not recursively stopped
  scsi: qla2xxx: Correct setting of SAM_STAT_CHECK_CONDITION
  scsi: qla2xxx: correctly shift host byte
  scsi: qla2xxx: Fix race condition between iocb timeout and initialisation
  scsi: qla2xxx: Avoid double completion of abort command
  scsi: qla2xxx: Fix small memory leak in qla2x00_probe_one on probe failure
  scsi: scsi_dh: Don't look for NULL devices handlers by name
  scsi: core: remove redundant assignment to shost->use_blk_mq