Merge tag 'renesas-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Second Round of Renesas ARM Based SoC DT Updates for v4.11

Enhancements:
- Add power-domains to mmcif on r7s72100 SoC
- Add OSTM to rskrza1/r7s72100
- Link ARM GIC to clock and clock domain on r8a774[35] SoCs

Clean-up:
- Correct SATA device status on r8a7779/marzen

* tag 'renesas-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: dts: r7s72100: add power-domains to mmcif
  ARM: dts: rskrza1: add ostm DT support
  ARM: dts: r7s72100: add ostm to device tree
  ARM: dts: r7s72100: add ostm clock to device tree
  ARM: dts: r8a7745: Link ARM GIC to clock and clock domain
  ARM: dts: r8a7743: Link ARM GIC to clock and clock domain
  ARM: dts: r8a7779, marzen: Fix sata device status
Signed-off-by: Olof Johansson <olof@lixom.net>

Lots of updates for mt2701:
Rearrange the dt nodes and fix unit address for pincontroler
Add nodes for:
- clock controller subsystems
- scpsys controller
- iommu and smi
- spi
- nand
- auxadc
- thermal controller and zones

Email address updated for mt7623 devicetree files.

* tag 'v4.10-next-dts32' of https://github.com/mbgg/linux-mediatek:
  arm: dts: mt2701: Add thermal device node.
  arm: dts: mt2701: Add auxadc device node.
  arm: dts: mt2701: Add nand device node
  arm: dts: mt2701: Add spi device node
  ARM: dts: mt2701: add iommu/smi dtsi node for mt2701
  ARM: dts: mediatek: update my email address
  arm: dts: mt2701: Add power domain controller device node
  arm: dts: mt2701: Add subsystem clock controller device nodes
  arm: dts: mt2701: Sort DT nodes by register address
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.11/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Device tree changes for omaps for v4.11 merge window. These
changes add earlycon stdout-path propety for the SoCs so far
tested with it. The other changes are addition of BeagleBone
green and making WLAN work on BeagleBone black wireless and
green wireless. The rest of the changes are the usual enabling
features on various devices:

- Enable devices on am335x-sl50
- Changes to dra7-evm boards to enable enable irqs for dp83867
  eth phys, add pinmux configuration for mmc, remov erratum
  i869 pinmux configurations, disable NAND support because of
  pin conflict, add pcf8575 used for lcd
- Remove NAND partition table for omap3-igep
- Configure USB Ethernet MAC from device tree for beagleboard
  xm, pandaboard, omap5-uevm and igepv5
- Configure am335x-chilisom to wake from RTC-only state
- Update Nanobone for external FRAM chip
- Clean up n900 dts
- Update am335x-phycore and am335x-wega for various devices
- Changes for am57xx-beagle-x15 to implement rgmii2 errata

* tag 'omap-for-v4.11/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (35 commits)
  ARM: dts: dra72/1-evm: add pcf8575 used for lcd
  ARM: dts: dra7xx: Add stdout-path property
  ARM: dts: am57xx: Add stdout-path property
  ARM: dts: am43xx: Add stdout-path property
  ARM: dts: am33xx: Add stdout-path property
  ARM: dts: am335x-sl50: Enable the Ambient Light Sensor.
  ARM: dts: am335x-sl50: Enable the MCP23017 GPIO Expander.
  ARM: dts: am335x-sl50: Enable BQ32000 Real Time Clock.
  ARM: dts: am335x-sl50: Enable SPI0 interface and Flash Memory.
  ARM: dts: am335x-sl50: Enable UART1.
  ARM: dts: am335x-sl50: Remove I2C1 node.
  ARM: dts: omap3-igep: Remove NAND partition table
  ARM: dts: am57xx-beagle-x15: implement errata "Ethernet RGMII2 Limited to 10/100 Mbps"
  ARM: dts: am335x-phycore-som: Remove partition tables
  ARM: dts: dra72-evm-revc: enable irqs for dp83867 eth phys
  ARM: dts: Configure BeagleBone peripheral USB VBUS irq
  ARM: dts: omap5-igep0050: Allow bootloader to configure USB Ethernet MAC
  ARM: dts: omap5-uevm: Allow bootloader to configure USB Ethernet MAC
  ARM: dts: pandaboard: Allow bootloader to configure USB Ethernet MAC
  ARM: omap3: beagleboard-xm: dt: Add ethernet to the device tree
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'davinci-for-v4.11/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt

Device tree updates for DaVinci DA850

* GPIO keys on DA850 LCDK
* LCDC display on DA850 LCDK
* USB OHCI on DA850 LCDK
* VPIF (video input) on DA850 LCDK
* Add a DA8xx specific compatible for UARTs
* Introduce support for Lego Mindstorms EV3

* tag 'davinci-for-v4.11/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: dts: Add LEGO MINDSTORMS EV3 dts
  dt-bindings: add "microchip,24c128" compatible string
  dt-bindings: Add LEGO MINDSTORMS EV3 compatible specification
  dt-bindings: Add vendor prefix for LEGO
  ARM: dts: da850: Add ti,da830-uart compatible for serial ports
  ARM: dts: davinci: da850-lcdk: enable VPIF
  ARM: dts: davinci: da850-evm: enable VPIF
  ARM: dts: davinci: da850: VPIF: add node and muxing
  ARM: dts: da850-lcdk: Enable ohci for omapl138 lcdk
  ARM: dts: da850: Add usb device node
  ARM: dts: da850: specify the maximum pixel clock rate for tilcdc
  ARM: dts: da850-lcdk: add the vga-bridge node
  ARM: dts: da850: rename the display node label
  ARM: dts: da850-lcdk: add gpio-keys
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'qcom-dts-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Qualcomm Device Tree Changes for v4.11

* Add Coresight components for APQ8064
* Fixup PM8058 nodes
* Add APQ8060 gyro and accel support
* Enable SD600 HDMI support
* Add RIVA supprort for Sony Yuga and SD600
* Add PM8821 support
* Add MSM8974 ADSP, USB gadget, SMD, and SMP2P support
* Fix IPQ8064 clock frequencies

* tag 'qcom-dts-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: dts: qcom: Add apq8064 CoreSight components
  ARM: dts: Add gyro and accel to APQ8060 Dragonboard
  ARM: dts: reference PM8058 as IRQ parent
  ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058
  ARM: dts: sd-600eval: enable 1.8v regulator on LS expansion
  ARM: dts: sd-600eval: add hdmi support
  ARM: dts: move hdmi pinctrl out of board file.
  ARM: dts: qcom: sd600eval: Enable riva-pil
  ARM: dts: qcom: sd600-eval: pm8921_s2 regulator properties
  ARM: dts: qcom: apq8064-sony-yuga: Enable riva-pil
  ARM: dts: qcom: apq8064: Add riva-pil node
  ARM: dts: apq8064: add support to pm8821
  arm: dts: qcom: Fix ipq board clock rates
  ARM: dts: msm8974: Remove "unused" reserved region
  ARM: dts: msm8974: Add ADSP PIL node
  ARM: dts: msm8974: Add ADSP smp2p and smd nodes
  ARM: dts: qcom: msm8974: Add USB gadget nodes
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'uniphier-dt-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt

UniPhier ARM SoC DT updates for v4.11

- Add eMMC, SD pin-mux nodes

* tag 'uniphier-dt-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  ARM: dts: uniphier: add SD pin-mux node
  ARM: dts: uniphier: add eMMC pin-mux node
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'keystone_dts_for_4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt

ARM: Keystone DTS update for 4.11

Brief:
	- MSM RAM node support for the Keystone 2 SOCs.
	- PSC node & reset controller node support for keystone 2 SOCs.
	- da830 UART node support.

* tag 'keystone_dts_for_4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: dts: keystone-k2e: Add PSC reset controller node
  ARM: dts: keystone-k2l: Add PSC reset controller node
  ARM: dts: keystone-k2hk: Add PSC reset controller node
  ARM: dts: keystone: Add PSC node
  ARM: keystone: dts: fix netcp clocks and add names
  ARM: dts: keystone-k2g: Reserve MSM RAM for boot monitor
  ARM: dts: keystone-k2e: Reserve MSM RAM for boot monitor
  ARM: dts: keystone-k2l: Reserve MSM RAM for boot monitor
  ARM: dts: keystone-k2hk: Reserve MSM RAM for boot monitor
  ARM: dts: keystone-k2g: Add MSM RAM node
  ARM: dts: keystone-k2e: Add MSM RAM node
  ARM: dts: keystone-k2l: Add MSM RAM node
  ARM: dts: keystone-k2hk: Add MSM RAM node
  ARM: dts: keystone: Add "ti,da830-uart" compatible string
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v4.11-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Bit of cleanup for the cortex-a9 uarts to have that soc-specific
spare-compatible as all others have, conversion to gpio constants
and addition of rk3288 qos nodes that need to be saved before a
power-domain gets turned off.

* tag 'v4.11-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: add soc-specific uart compatibles for rk3066/rk3188
  ARM: dts: rockchip: use pin constants to describe gpios
  ARM: dts: rockchip: add qos node for rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add thermal controller device nodes for MT2701.
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

DRA72 and DRA718 EVM boards has a pcf8575 gpio expander
which is used for the LCD/LEDs and USB vbus detection.
Add the node for the pcf8575.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Link the ARM GIC to the INTC-SYS module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.

Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Link the ARM GIC to the INTC-SYS module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.

Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Pro4 SoC has 2 slots of SD controllers, so 2 pin-mux nodes
(SD and SD1) are needed.  The other SoCs have only 1 SD slot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

All UniPhier SoCs support an eMMC controller.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Tested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for the ISL29023 ALS connected via the I2C bus.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for the 16-Bit I/O Expander connected via the I2C bus.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for the BQ32000 Real Time Clock connected to the I2C bus
and disable the AM335x Real Time Clock.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for the 32Mb Serial Flash Memory connected to SPI0
and using CS1.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The UART1 is connected to the infrared (IR) receiver module, so enable it
to be able to comunicate with it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

I2C1 is not used so remove it in order to avoid conflicts.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds a device tree definition file for LEGO MINDSTORMS EV3.

What is working:

* Pin muxing
* Pinconf
* GPIOs
* MicroSD card reader
* UART on input port 1
* Buttons
* LEDs
* Poweroff/reset
* Flash memory
* EEPROM
* USB host port
* USB peripheral port

What is not working/to be added later:

* Speaker - have patch submitted to get pwm-beeper working - maybe someday
  it will have a real sound driver that uses PRU
* A/DC chip - have driver submitted and accepted - waiting for ack on
  device tree bindings
* Display - waiting for "simple DRM" to be mainlined
* Bluetooth - needs new driver for sequencing power/enable/clock
* Input and output ports - need some sort of new phy or extcon driver as
  well as PRU UART and PRU I2C drivers
* Battery indication - needs new power supply driver

Note on flash partitions:

These partitions are based on the official EV3 firmware from LEGO. It is
expected that most users of the mainline kernel on EV3 will be booting from
an SD card while retaining the official firmware in the flash memory.
Furthermore, the official firmware uses an ancient U-Boot (2009) that has
no device tree support. So, it makes sense to have this partition table in
the EV3 device tree file. In the unlikely case that anyone does create
their own firmware image with different partitioning, they can use a modern
U-Boot in their own firmware image that modifies the device tree with the
custom partitions.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

This adds "microchip,24c128" to the list of compatible strings for i2c
eeproms.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

This adds the board level device tree specification for LEGO MINDSTORMS EV3
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Add a vendor prefix for LEGO Systems A/S
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.11,
please pull the following changes:

- Rafal enables the UART by default on all BCM5301x, BCM4708, BCM4709 since
  every device found out there has it enabled by default. He also fixes the
  LED definitions for the Luxul XWR-3100 device, enables USB controllers and
  their respective PHY devices, specifies the correct GPIO to power on USB
  HUBs, adds the additional RAM bank for somes devices, and finally sets the
  correct 5Ghz frequency limits on the Netgear R8000

- Jon does a number of Norsthar Plus SoC cleanups, fixes NAND partitions unit
  addresses, adds QSPI support to a bunch of boards, adds Ethernet switch ports
  to the BCM958625K reference board, enables 3rd Ethernet MAC instance to
  relevant DTSes, enables Ethernet on the XMC board, and finally adds SD/MMC
  support to the XMC board

- Boris adds the Video Encoder nodes to the Raspberry Pi DTS include files
  ands enables it on the relevant boards

- Dan adds support for two new Luxul devices: XAP-1410 and XWR-1200, both
  BCM47081 based SoCs

* tag 'arm-soc/for-4.11/devicetree' of http://github.com/Broadcom/stblinux:
  ARM: dts: bcm283x: Enable the VEC IP on all RaspberryPi boards
  ARM: dts: bcm283x: Add VEC node in bcm283x.dtsi
  ARM: dts: BCM5301X: Add DT for Luxul XWR-1200
  ARM: dts: BCM5301X: Add DT for Luxul XAP-1410
  ARM: dts: BCM5301X: Set 5 GHz wireless frequency limits on Netgear R8000
  ARM: dts: NSP: Add SD/MMC support
  ARM: dts: NSP: Add Ethernet to NSP XMC
  ARM: dts: NSP: Add and enable amac2
  ARM: dts: NSP: Add BCM958625K switch ports
  ARM: dts: NSP: Add QSPI support to missing boards
  ARM: dts: NSP: Correct NAND partition unit address
  ARM: dts: NSP: DT Clean-ups
  ARM: dts: BCM53573: Specify USB ports of on-SoC controllers
  ARM: dts: BCM5301X: Specify all RAM by including an extra block
  ARM: dts: BCM5301X: Set GPIO enabling USB power on Netgear R7000
  ARM: dts: BCM5301X: Specify USB controllers in DT
  ARM: dts: BCM5301X: Fix LAN LED labels for Luxul XWR-3100
  ARM: dts: BCM5301X: Enable UART by default for BCM4708(1), BCM4709(4) & BCM53012
Signed-off-by: Olof Johansson <olof@lixom.net>

Tango4 provides 2 USB 2.0 controllers.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Tango4 provides 2 SD/SDIO/eMMC controllers.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

http://elinux.org/Device_Tree_Usage#aliases_NodeSigned-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The Power Sleep Controller (PSC) module contains specific
memory-mapped registers that can be used to perform reset
management using specific bits for the DSPs available on the
SoC. The PSC is defined using a syscon node, and the reset
functionality is defined using a child syscon reset controller
node.

Add this syscon reset controller node as well as the reset
control data for the resets it supports for the 66AK2E SoCs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>

The Power Sleep Controller (PSC) module contains specific
memory-mapped registers that can be used to perform reset
management using specific bits for the DSPs available on the
SoC. The PSC is defined using a syscon node, and the reset
functionality is defined using a child syscon reset controller
node.

Add this syscon reset controller node as well as the reset
control data for the resets it supports for the 66AK2L SoCs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>

The Power Sleep Controller (PSC) module contains specific
memory-mapped registers that can be used to perform reset
management using specific bits for the DSPs available on the
SoC. The PSC is defined using a syscon node, and the reset
functionality is defined using a child syscon reset controller
node.

Add this syscon reset controller node as well as the reset
control data for the resets it supports for the 66AK2H SoCs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>

The Power Sleep Controller (PSC) module is responsible
for the power and clock management for each of the peripherals
present on the SoC. Represent this as a syscon node so that
multiple users can leverage it for various functionalities.
Signed-off-by: Suman Anna <s-anna@ti.com>
[afd@ti.com: add simple-mfd compatible]
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>