self-assignment of a variable doesn't make a lot of sense.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

- A couple of fixes that never made it into fixes-3.12
- Make NO_EVICT bo's available for shrinkers when on delayed-delete list
- Allow retrying page-faults that need to wait for GPU.

* 'ttm-next-3.13' of git://people.freedesktop.org/~thomash/linux:
  drm/ttm: Fix memory type compatibility check
  drm/ttm: Fix ttm_bo_move_memcpy
  drm/ttm: Handle in-memory region copies
  drm/ttm: Make NO_EVICT bos available to shrinkers pending destruction
  drm/ttm: Allow vm fault retries

Pull request for vmwgfx. Currently just the DMA address stuff.

* 'vmwgfx-next-3.13' of git://people.freedesktop.org/~thomash/linux:
  drm/vmwgfx: Use the linux DMA api to get valid device addresses of pages
  drm/ttm: Enable the dma page pool also for intel IOMMUs

Also check the busy placements before deciding to move a buffer object.
Failing to do this may result in a completely unneccessary move within a
single memory type.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org

All error paths will want to keep the mm node, so handle this at the
function exit. This fixes an ioremap failure error path.
Also add some comments to make the function a bit easier to understand.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org

Fix the case where the ttm pointer may be NULL causing
a NULL pointer dereference.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellström <thellstrom@vmware.com>
Cc: stable@vger.kernel.org

NO_EVICT bos that are not idle when all references are dropped are put on
the delayed destroy list. However, since they are not on LRU lists, they
are not available to shrinkers at that point, and buffers on the delayed
destroy list are not checked very often for idle.

So when these buffers are put on the delayed destroy list, clear the
NO_EVICT flag and put them on the right LRU list. This way they are
immediately available for eviction or shrinkers and will not cause false
OOMS.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>

Make use of the FAULT_FLAG_ALLOW_RETRY flag to allow dropping the
mmap_sem while waiting for bo idle.

FAULT_FLAG_ALLOW_RETRY appears to be primarily designed for disk waits
but should work just as fine for GPU waits..
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>

The code handles three different cases:
1) physical page addresses. The ttm page array is used.
2) DMA subsystem addresses. A scatter-gather list is used.
3) Coherent pages. The ttm dma pool is used, together with the dma_ttm
array os dma_addr_t
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>

Used by the vmwgfx driver
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

So GNOME userspace has an issue with when it rescans for modes on hotplug
events, if the monitor has no EDID it assumes that nothing has changed on
EDID as with real hw we'd never have new modes without a new EDID, and they
kind off rely on the behaviour now, however with virtual GPUs we would
like to rescan the modes and get a new preferred mode on hotplug events
to handle dynamic guest resizing (where you resize the host window and the
guest resizes with it).

This is a simple property we can make userspace watch for to trigger new
behaviour based on it, and can be used to replaced EDID hacks in virtual
drivers.

Acked-by: Marc-André Lureau <marcandre.lureau@gmail.com> (on irc)
Signed-off-by: Dave Airlie <airlied@redhat.com>

Instead of freeing minors in drm_dev_unregister(), we only unplug them and
delay the free to drm_dev_free(). Note that if drm_dev_register() has
never been called, minors are NULL and this has no effect.

This change is needed to allow early device unregistration. If we want to
call drm_dev_unregister() on live devices, we need to guarantee that
minors are still valid (but unplugged). This way, any open file can still
access file_priv->minor->dev to get the DRM device. However, the minor is
unplugged so no new users can occur.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Don't delay minor removal to drm_put_minor(). Otherwise, user-space can
still open the minor and cause the kernel to oops. Instead, remove the
minor during unplug so any new open() will fail to access this minor.

Note that open() and drm_unplug_minor() are both protected by the global
DRM mutex so we're fine.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

There is no reason to delay debugfs-cleanup to drm_put_minor(). We should
forbid any access to debugfs files once the device is dead. Chances they
oops once a card was unplugged are very high, anyway.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm_get_minor() is only used in one file. Make it static and add a
kernel-doc comment which documents the current semantics.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Allow passing NULL as minor to simplify DRM destruction paths. Also remove
the double-pointer reset as it is no longer needed. drm_put_minor() is
only called when the underlying object is destroyed. Hence, resetting
minors to NULL is not necessary.

As drm_put_minor() is no longer used by other DRM files, we can make it
static, too.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This protects drm_unplug_minor() against repeated calls so we can use it
in drm_put_minor(). This allows us to further simplify it in follow-ups as
we no longer do minor-destruction in both functions but only in
drm_unplug_minor().
Also add kernel-doc comments about what these calls do.

[airlied: fixup for changes to kdev stuff]
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Bit-copying restoration of CRTC structure in failure-recovery
path of drm_crtc_helper_set_config function evokes a
subtle and rare, but very dangerous, corruption of
CRTC mutex structure.

Namely, if drm_crtc_helper_set_config takes the path under
'fail:' label *and* some other process has attempted to
grab the crtc mutex (and got blocked), restoring the CRTC
structure by bit-copying it will overwrite the CRTC mutex
state and the waiters list pointer within the mutex structure.
Consequently the blocked process will never be scheduled.

This patch fixes the issue by eliminating the bit-copy
restoration. The elimination is possible because previous
patches have cleaned up the resoration path so that only
the fields touched by the drm_crtc_helper_set_config function
are saved and restored if necessary.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

There is no need to set crtc->enabled field in
drm_crtc_helper_set_config. This is already done (and
properly restored in case of failure) in
drm_crtc_helper_set_mode that is called by
drm_crtc_helper_set_config. Doing it at only one
place makes restoration in case of failure easier.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

There is no need to save or restore hwmode field, because by
the time this function sets this field, it cannot fail any more.
However, we should save old enabled field because if
the function fails, we want to return with unchanged CRTC.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Old framebuffer is stored in save_set.fb and it is
the same value that is later stored in old_fb.
This makes old_fb redundant so we can replace
it with save_set.fb.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Replace the sparse array of booleans with a bitfield.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

When a second process opens the device and master transferrence is
complete, we walk the list of open devices and remove their
authentication. This also revokes our root privilege. Instead of simply
dropping the authentication, this patch reverts the authenticated state
back to its original value.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This causes problems with never going busy due to ptherm polling,
and after talking to Ben I can't see it being required.
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm_connector_sysfs_add() explicitly checks if connector->kdev
is already populated and returns success. So it clearly now allows
being called multiple times. Remove some stale comments to the contrary.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Don't block forever if there is nothing to wait for.
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Rafa? Mi?ecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

qxl devices can have a 64bit surface bar, which is quite handy if
you need a bit more surface memory.  So try to use it if it is
present.  Note that this bar might be mapped above 4g.

QEMU command line to check that out:

    qemu-system-x86_64 -m 4g \
        -vga qxl -global qxl-vga.vram64_size_mb=512 \
        $otheroptions
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Explicitly set 1024x768 as default mode, so the display doesn't come up
with the largest supported mode.

While being at it drop first three drm_add_modes_noedid calls.  As
drm_add_modes_noedid fills the mode list with modes from the database
*up to* the specified size it is pretty pointless to call it multiple
times with different sizes.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

New helper function to set the preferred video mode.  Can be called
after drm_add_modes_noedid if you don't want the largest supported
video mode be used by default.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm_fb_get_bpp_depth() likes to complain about unsupported pixel formats
but doesn't bother telling us what the format was. Also format_check()
just returns an error when it encouters an invalid format, leaving the
user scratching his head trying to figure out why addfb failed. Make
life a bit easier by using drm_get_format_name() in both places.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

I got very confused when I tried to compare the EST modes with the spec.
Bring over a comment from xf86EdidModes.c that actually describes some
of history where these things came from.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Also check the est3 modes whose presence is indicated by bit 0.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The correct refresh rate for this mode is 75, not 85.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Let's be a bit more consistent with our error values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Let's be a bit more consistent with our error values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Let's be a bit more consistent with our error values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Let's be a bit more consistent with our error values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>