Refactor pca954x_irq_handler() to:
  - use for_each_set_bit() macro
  - use IRQ_RETVAL() macro

Above change makes code easy to read and understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

After a transfer timeout, some faulty I2C slave devices might hold down
the SDA pin. We can generate a bus clear command, hoping that the slave
might release the pins.
If the CLEAR command is not supported, we will use gpio recovery, if
available, to reset the bus.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Fix i2c_pxa_wait_bus_not_busy()'s boundary conditions, so that a
coincidental success and timeout results in the function returning
success.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Clean up decode_bits() to use pr_cont(), and move the newline into the
function rather than at its two callsites. Avoid printing an
unnecessary space before the newline.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The IRQ log output is supposed to appear on a single line.  However,
commit 3a2dc167 ("i2c: pxa: Update debug function to dump more info
on error") resulted in it being printed one-entry-per-line, which is
excessively long.

Fixing this is not a trivial matter; using pr_cont() doesn't work as
the previous dev_dbg() may not have been compiled in, or may be
dynamic.

Since the rest of this function output is at error level, and is also
debug output, promote this to error level as well to avoid this
problem.

Reduce the number of always zero prefix digits to save screen real-
estate.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Move the ID tables into one place, near the device dependent data.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Move driver-private definitions out of the i2c-pxa.h platform data
header file into the driver itself. Nothing outside of the driver
makes use of these constants.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Always set the fm and hs members of struct pxa_reg_layout. These
members are already taking space, we don't need code as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add definitions for the bits in the IBMR register, and use them in the
code. This improves readability.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Arrange the register field definitions to be grouped together, rather
than the Armada-3700 definitions being separated from the rest of the
definitions.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Re-arrange the PXA I2C code to avoid forward declarations, and keep
similar functionality (e.g. the non-IRQ mode support) together. This
improves code readability.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Arrange the includes to be in alphabetical order to help avoid
duplicated includes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

i2c-pxa does not need linux/sched.h nor linux/time.h includes, so
remove these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

i2c-pxa was created before i2c_8bit_addr_from_msg() was implemented,
and used its own i2c_pxa_addr_byte() which is functionally the same.
Sadly, it was never updated to use this new helper. Switch it over.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

In i2c_powermac_register_devices(), variable 'found_onyx' is bool and
assigned '0' and 'true' in different places. Use 'false' instead of '0'.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

We want to break with "i" set to zero whether we find the rate we want
or not.  In the current code, if we don't find the rate we want then it
exits the loop with "i" set to -1 and results in an array underflow.

Fixes: 09cc9a3b ("i2c: stm32f7: allows for any bus frequency")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add support for SMBUS quick command.

SMBUS quick command passes single bit of information to the
slave (target) device. Can be used to turn slave device on or off.

By default i2c_detect tool uses the smbus quick cmd to try and
detect devices. Without this support it will not detect some slaves.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use of_property_read_u32 to read the "reg" and "i2c-address" property
instead of using of_get_property to check the return values.
Signed-off-by: Aishwarya R <aishwaryarj100@gmail.com>
Tested-by: Erhard Furtner <erhard_f@mailbox.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The '>' expression itself is bool, no need to convert it to bool again.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

If there is no interrupt defined then an error is logged due
to the use of platform_get_irq. The driver handles not having
the interrupt by falling back to polling, therefore make
the appropriate call when claiming it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Some bindings are for the bus master, some are for the slaves.
Regroup them and give them separate headings to make it clear.
Also, remove references to "generic names" which is for nodes and not
for compatibles.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Do not limitate to the 3 (100KHz, 400KHz, 1MHz) bus frequency but
instead allows any frequency (if it matches timing requirements).
Depending on the requested frequency, use the spec data from either
Standard, Fast or Fast Plus mode.

Hardcoding of min/max bus frequencies is removed and is instead computed.

The driver do not use anymore speed identifier but instead handle
directly the frequency and figure out the spec data (necessary
for the computation of the timing register) based on the frequency.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

For STM32F7, STM32H7 and STM32MP1 SoCs, if timing parameters
match, the bus clock frequency can be from 1Hz to 1MHz.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Do not print an error trace when deferring probe for some resource.
Fix as well the error message in case of tx dma_request_chan failure.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The BCM2711, supported by ARCH_BCM2835, also has a controller by the
brcmstb driver so let's allow it to be compiled on that platform.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

If the slave eeprom has a "firmware-name" in devicetree, then pre-load
the data in the eeprom with this file. Otherwise we init the eeprom with
0xFF.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Björn Ardö <bjorn.ardo@axis.com>
[wsa: some cosmetic changes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

it will print an error message by itself when platform_get_irq()
goes wrong. so don't need dev_err() in here again.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This commit adds I2C bus support for the Camera Control Interface
(CCI) I2C controller found on the Qualcomm SoC processors. This I2C
controller supports two masters and they are registered to the core.

CCI versions supported in the driver are msm8916, msm8996 and sdm845.

This is a rework of the patch posted by Vinod:
https://patchwork.kernel.org/patch/10569961/

With additional fixes + most of the comments addressed.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[wsa: removed err msg after platform_get_irq]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add DT binding document for Qualcomm Camera Control Interface (CCI)
I2C controller.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Added support for I2C slave functionality
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Custom parameters for HCNT/LCNT are not available for OF based system.
Thus, we will use existing SCL timing parameter calculation functions
for High Speed Mode too.

The value for the parameters tSYMBOL and tLOW is taken from DesignWare
DW_apb_i2c Databook v2.01a, section 3.15.4.6. The calculation should
assume higher bus load since it gives slower timing parameter.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Custom parameters for HCNT/LCNT are not available for OF based system.
Thus, we will use existing SCL timing parameter calculation functions
for Fast Mode Plus.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add information on slave addr in the nack debug message.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i801_add_mux() fills in the GPIO lookup table by manually populating an
array of gpiod_lookup structures.  Use the existing GPIO_LOOKUP() helper
macro instead, to relax a dependency on the gpiod_lookup structure's
member names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

When I wanted to print the chosen values to debug output, I concluded
that a helper function to parse one timing would be helpful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper
equivalents have a secondary SMBus controller at I/O port address
0x0B20.  This bus is used by several manufacturers to control
motherboard RGB lighting via embedded controllers.  I have been using
this bus in my OpenRGB project to control the Aura RGB on many
motherboards and ASRock also uses this bus for their Polychrome RGB
controller.

I am not aware of any CZ-compatible platforms which do not have the
second SMBus channel.  All of AMD's AM4- and Threadripper- series
chipsets that OpenRGB users have tested appear to have this secondary
bus.  I also noticed this secondary bus is present on older AMD
platforms including my FM1 home server.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

use devm_platform_ioremap_resource() to simplify code, it
contains platform_get_resource and devm_ioremap_resource.
Reviewed-by: Barry Song <baohua@kernel.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Robert Richter <rrichter@marvell.com>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>