- 20 Nov, 2019 40 commits
-
-
Felix Fietkau authored
[ Upstream commit d9c52fd1 ] Tx99 is typically configured via a monitor mode interface, which does not get added to the driver as a vif. Since the code currently expects a configured virtual interface for tx99, enabling tx99 via debugfs fails. Since the vif is not needed anyway, remove all checks for it. Signed-off-by:
Felix Fietkau <nbd@nbd.name> [kvalo@codeaurora.org: s/CPTCFG/CONFIG/] Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Rakesh Pillai authored
[ Upstream commit 58da3b42 ] WCN3990 has the MAC_PCU_ADDR1 configured properly and hence it will not send spurious ack frames during boot up. Hence the reset_rx_filter workaround is not needed for WCN3990. Add a hw_param to indicate if hardware rx filter reset is needed and skip the reset_rx_filter for WCN3990. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1 Signed-off-by:
Rakesh Pillai <pillair@codeaurora.org> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit b8e13154 ] snd_seq_system_client_init() doesn't check the errors returned from its port creations. Let's do it properly and handle the error paths. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Rajeev Kumar Sirasanagandla authored
[ Upstream commit 7417844b ] When REGULATORY_COUNTRY_IE_IGNORE is set, __reg_process_hint_country_ie() ignores the country code change request from __cfg80211_connect_result() via regulatory_hint_country_ie(). After Disconnect, similar to above, country code should not be reset to world when country IE ignore is set. But this is violated and restore of regulatory settings is invoked by cfg80211_disconnect_work via regulatory_hint_disconnect(). To address this, avoid regulatory restore from regulatory_hint_disconnect() when COUNTRY_IE_IGNORE is set. Note: Currently, restore_regulatory_settings() takes care of clearing beacon hints. But in the proposed change, regulatory restore is avoided. Therefore, explicitly clear beacon hints when DISABLE_BEACON_HINTS is not set. Signed-off-by:
Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Andy Shevchenko authored
[ Upstream commit 962341b5 ] When we have first case to fall through it's not enough to put single comment there to satisfy compiler. Instead of doing that, return fall back value directly from default case. This to avoid following warnings: drivers/extcon/extcon-intel-cht-wc.c: In function ‘cht_wc_extcon_get_charger’: include/linux/device.h:1420:2: warning: this statement may fall through [-Wimplicit-fallthrough=] _dev_warn(dev, dev_fmt(fmt), ##__VA_ARGS__) ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/extcon/extcon-intel-cht-wc.c:148:3: note: in expansion of macro ‘dev_warn’ dev_warn(ext->dev, ^~~~~~~~ drivers/extcon/extcon-intel-cht-wc.c:152:2: note: here case CHT_WC_USBSRC_TYPE_SDP: ^~~~ Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by:
-
Bjorn Andersson authored
[ Upstream commit 1e28dbbe ] da8xx_rproc_mem size is of type size_t, so use %zx to format the debug print of it to avoid a compile warning. Acked-by:
Suman Anna <s-anna@ti.com> Reviewed-by:
Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Alexandre Belloni authored
[ Upstream commit c856618d ] The ID for RV8803 must be rv_8803 Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 777d8ae5 ] devm_kcalloc() returns NULL, it never returns error pointers. In the current code we would return PTR_ERR(NULL) which is success, instead of returning the -ENOMEM error code. Fixes: a0a1a1ba ("rtc: sysfs: facilitate attribute add to rtc device") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Jay Foster authored
[ Upstream commit 10af10db ] Fix a typo. No functional change made by this patch. Signed-off-by:
Jay Foster <jayfoster@ieee.org> Signed-off-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
-
Geert Uytterhoeven authored
[ Upstream commit 441f61e3 ] Update the SATA device nodes on R-Car H1, H2, and M2-W to use a 2 MiB I/O space, as specified in Rev.1.0 of the R-Car H1 and R-Car Gen2 hardware user manuals. See also commit e9f0089b ("arm64: dts: r8a7795: Correct SATA device size to 2MiB"). Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 33e26418 ] get_seconds() and do_gettimeofday() are only used by a few modules now any more (waiting for the respective patches to get accepted), and they are among the last holdouts of code that is not y2038 safe in the core kernel. Move the implementation into the timekeeping32.h header to clean up the core kernel and isolate the old interfaces further. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Aapo Vienamo authored
[ Upstream commit 6ff7705d ] On p2180 sdmmc4 is powered from a fixed 1.8 V regulator. Signed-off-by:
Aapo Vienamo <avienamo@nvidia.com> Reviewed-by:
Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Aapo Vienamo authored
[ Upstream commit 13136a47 ] Implement support for the PMC_IMPL_E_33V_PWR register which replaces PMC_PWR_DET register interface of the SoC generations preceding Tegra186. Also add the voltage bit offsets to the tegra186_io_pads[] table and the AO_HV pad. Signed-off-by:
Jon Hunter <jonathanh@nvidia.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 6f128fa4 ] The "frames" variable is unsigned so the error handling doesn't work properly. Signed-off-by:
-
Andre Przywara authored
[ Upstream commit 480f58cd ] According to the NanoPi-A64 schematics, DCDC1 is connected to a voltage rail named "VDD_SYS_3.3V". All users seem to expect 3.3V here: the Ethernet PHY, the uSD card slot, the camera interface and the GPIO pins on the headers. Fix up the voltage on the regulator to lift it up to 3.3V. Signed-off-by:
Andre Przywara <andre.przywara@arm.com> Acked-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
Andre Przywara authored
[ Upstream commit 93366b49 ] The Olinuxino board uses DDR3L chips which are supposed to be driven with 1.35V. The reset default of the AXP is properly set to 1.36V. While technically the chips can also run at 1.5 volts, changing the voltage on the fly while booting Linux is asking for trouble. Also running at a lower voltage saves power. So fix the DCDC5 value to match the actual board design. Signed-off-by:
Martin Lucina <martin@lucina.net> Acked-by:
-
Samuel Holland authored
[ Upstream commit 09b964af ] The Orange Pi Win has a microSD card slot which is connected via all four SD data lines. As the DT was not mentioning this fact, we got the default single bit transfers, losing out on performance. Also, as microSD does not have a write protect switch, we disable this feature in the DT node. Signed-off-by:
Samuel Holland <samuel@sholland.org> Signed-off-by:
-
Vinod Koul authored
[ Upstream commit e1c815f4 ] In case of error, we can dereference uninitialized 'adev' drivers/soundwire/intel_init.c:154 sdw_intel_acpi_cb() error: uninitialized symbol 'adev'. Fix that by not using adev for warn print and make it pr_err. Reported-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Shreyas NC authored
[ Upstream commit a306a0e4 ] Deferred messages are async messages used to synchronize transitions mostly while doing a bank switch on multi links. On successful transitions these messages are marked complete and thereby confirming that all the buses performed bank switch successfully. So, initialize the completion structure for the same. Signed-off-by:
Sanyog Kale <sanyog.r.kale@intel.com> Signed-off-by:
Shreyas NC <shreyas.nc@intel.com> Acked-by:
-
Rongyi Chen authored
[ Upstream commit 58c0f798 ] Currently the register offset of the PWM bus gate in Allwinner H6 clock driver is wrong. Fix this issue. Fixes: 542353ea ("clk: sunxi-ng: add support for the Allwinner H6 CCU") Signed-off-by:
Rongyi Chen <chenyi@tt-cool.com> [Icenowy: refactor commit message] Signed-off-by:
Icenowy Zheng <icenowy@aosc.io> Signed-off-by:
-
Marcus Folkesson authored
[ Upstream commit 0833627f ] Do not try to write negative values and make sure that the write goes well. Signed-off-by:
Marcus Folkesson <marcus.folkesson@gmail.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Tamizh chelvam authored
[ Upstream commit bd1d3950 ] When continuously running wifi up/down sequence, the napi poll can be scheduled after the CE buffers being freed by ath10k_pci_flush Steps: In a certain condition, during wifi down below scenario might occur. ath10k_stop->ath10k_hif_stop->napi_schedule->ath10k_pci_flush->napi_poll(napi_synchronize). In the above scenario, CE buffer entries will be freed up and become NULL in ath10k_pci_flush. And the napi_poll has been invoked after the flush process and it will try to get the skb from the CE buffer entry and perform some action on that. Since the CE buffer already cleaned by pci flush this action will create NULL pointer dereference and trigger below kernel panic. Unable to handle kernel NULL pointer dereference at virtual address 0000005c PC is at ath10k_pci_htt_rx_cb+0x64/0x3ec [ath10k_pci] ath10k_pci_htt_rx_cb [ath10k_pci] ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci] ath10k_ce_per_engine_service [ath10k_pci] ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci] ath10k_ce_per_engine_service_any [ath10k_pci] ath10k_pci_napi_poll+0x48/0xec [ath10k_pci] ath10k_pci_napi_poll [ath10k_pci] net_rx_action+0xac/0x160 net_rx_action __do_softirq+0xdc/0x208 __do_softirq irq_exit+0x84/0xe0 irq_exit __handle_domain_irq+0x80/0xa0 __handle_domain_irq gic_handle_irq+0x38/0x5c gic_handle_irq __irq_usr+0x44/0x60 Tested on QCA4019 and firmware version 10.4.3.2.1.1-00010 Signed-off-by:
Tamizh chelvam <tamizhr@codeaurora.org> Signed-off-by:
-
Ard Biesheuvel authored
[ Upstream commit db878f76 ] DT nodes may have a 'status' property which, if set to anything other than 'ok' or 'okay', indicates to the OS that the DT node should be treated as if it was not present. So add that missing logic to the OP-TEE driver. Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Jens Wiklander <jens.wiklander@linaro.org> Signed-off-by:
-
Stefan Agner authored
[ Upstream commit b1ec0802 ] After finding a reasonable gain, the function converts the configured gain to a gain configuration option selector enum max9611_csa_gain. Make the conversion clearly visible by using an explicit cast. This also avoids a warning seen with clang: drivers/iio/adc/max9611.c:292:16: warning: implicit conversion from enumeration type 'enum max9611_conf_ids' to different enumeration type 'enum max9611_csa_gain' [-Wenum-conversion] *csa_gain = gain_selectors[i]; ~ ^~~~~~~~~~~~~~~~~ Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
-
Eugen Hristev authored
commit fed23c58 upstream. The quirks2 are parsed and set (e.g. from DT) before the quirk for broken HS200 is set in the driver. The driver needs to enable just this flag, not rewrite the whole quirk set. Fixes: 7871aa60 ("mmc: sdhci-of-at91: add quirk for broken HS200") Signed-off-by:
Eugen Hristev <eugen.hristev@microchip.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Roman Gushchin authored
commit 0362f326 upstream. An exiting task might belong to an offline cgroup. In this case an attempt to grab a cgroup reference from the task can end up with an infinite loop in hugetlb_cgroup_charge_cgroup(), because neither the cgroup will become online, neither the task will be migrated to a live cgroup. Fix this by switching over to css_tryget(). As css_tryget_online() can't guarantee that the cgroup won't go offline, in most cases the check doesn't make sense. In this particular case users of hugetlb_cgroup_charge_cgroup() are not affected by this change. A similar problem is described by commit 18fa84a2 ("cgroup: Use css_tryget() instead of css_tryget_online() in task_get_css()"). Link: http://lkml.kernel.org/r/20191106225131.3543616-2-guro@fb.comSigned-off-by:
Roman Gushchin <guro@fb.com> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Acked-by:
Tejun Heo <tj@kernel.org> Reviewed-by:
Shakeel Butt <shakeelb@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Roman Gushchin authored
commit 00d484f3 upstream. We've encountered a rcu stall in get_mem_cgroup_from_mm(): rcu: INFO: rcu_sched self-detected stall on CPU rcu: 33-....: (21000 ticks this GP) idle=6c6/1/0x4000000000000002 softirq=35441/35441 fqs=5017 (t=21031 jiffies g=324821 q=95837) NMI backtrace for cpu 33 <...> RIP: 0010:get_mem_cgroup_from_mm+0x2f/0x90 <...> __memcg_kmem_charge+0x55/0x140 __alloc_pages_nodemask+0x267/0x320 pipe_write+0x1ad/0x400 new_sync_write+0x127/0x1c0 __kernel_write+0x4f/0xf0 dump_emit+0x91/0xc0 writenote+0xa0/0xc0 elf_core_dump+0x11af/0x1430 do_coredump+0xc65/0xee0 get_signal+0x132/0x7c0 do_signal+0x36/0x640 exit_to_usermode_loop+0x61/0xd0 do_syscall_64+0xd4/0x100 entry_SYSCALL_64_after_hwframe+0x44/0xa9 The problem is caused by an exiting task which is associated with an offline memcg. We're iterating over and over in the do {} while (!css_tryget_online()) loop, but obviously the memcg won't become online and the exiting task won't be migrated to a live memcg. Let's fix it by switching from css_tryget_online() to css_tryget(). As css_tryget_online() cannot guarantee that the memcg won't go offline, the check is usually useless, except some rare cases when for example it determines if something should be presented to a user. A similar problem is described by commit 18fa84a2 ("cgroup: Use css_tryget() instead of css_tryget_online() in task_get_css()"). Johannes: : The bug aside, it doesn't matter whether the cgroup is online for the : callers. It used to matter when offlining needed to evacuate all charges : from the memcg, and so needed to prevent new ones from showing up, but we : don't care now. Link: http://lkml.kernel.org/r/20191106225131.3543616-1-guro@fb.comSigned-off-by:
Shakeel Butt <shakeeb@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Michal Koutn <mkoutny@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Yang Shi authored
commit a85dfc30 upstream. Commit d8835445 ("mm: mempolicy: make the behavior consistent when MPOL_MF_MOVE* and MPOL_MF_STRICT were specified") fixed the return value of mbind() for a couple of corner cases. But, it altered the errno for some other cases, for example, mbind() should return -EFAULT when part or all of the memory range specified by nodemask and maxnode points outside your accessible address space, or there was an unmapped hole in the specified memory range specified by addr and len. Fix this by preserving the errno returned by queue_pages_range(). And, the pagelist may be not empty even though queue_pages_range() returns error, put the pages back to LRU since mbind_range() is not called to really apply the policy so those pages should not be migrated, this is also the old behavior before the problematic commit. Link: http://lkml.kernel.org/r/1572454731-3925-1-git-send-email-yang.shi@linux.alibaba.com Fixes: d8835445 ("mm: mempolicy: make the behavior consistent when MPOL_MF_MOVE* and MPOL_MF_STRICT were specified") Signed-off-by:
Yang Shi <yang.shi@linux.alibaba.com> Reported-by:
Li Xinhai <lixinhai.lxh@gmail.com> Reviewed-by:
-
Eric Auger authored
commit 4e7120d7 upstream. For both PASID-based-Device-TLB Invalidate Descriptor and Device-TLB Invalidate Descriptor, the Physical Function Source-ID value is split according to this layout: PFSID[3:0] is set at offset 12 and PFSID[15:4] is put at offset 52. Fix the part laid out at offset 52. Fixes: 0f725561 ("iommu/vt-d: Add definitions for PFSID") Signed-off-by:
Eric Auger <eric.auger@redhat.com> Acked-by:
Jacob Pan <jacob.jun.pan@linux.intel.com> Cc: stable@vger.kernel.org # v4.19+ Acked-by:
Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Corentin Labbe authored
commit 40a1dcee upstream. When PHY is not powered, the probe function fail and some resource are still unallocated. Furthermore some BUG happens: dwmac-sun8i 5020000.ethernet: EMAC reset timeout ------------[ cut here ]------------ kernel BUG at /linux-next/net/core/dev.c:9844! So let's use the right function (stmmac_pltfr_remove) in the error path. Fixes: 9f93ac8d ("net-next: stmmac: Add dwmac-sun8i") Cc: <stable@vger.kernel.org> # v4.15+ Signed-off-by:
Corentin Labbe <clabbe@baylibre.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Al Viro authored
commit 762c6968 upstream. We need to get the underlying dentry of parent; sure, absent the races it is the parent of underlying dentry, but there's nothing to prevent losing a timeslice to preemtion in the middle of evaluation of lower_dentry->d_parent->d_inode, having another process move lower_dentry around and have its (ex)parent not pinned anymore and freed on memory pressure. Then we regain CPU and try to fetch ->d_inode from memory that is freed by that point. dentry->d_parent *is* stable here - it's an argument of ->lookup() and we are guaranteed that it won't be moved anywhere until we feed it to d_add/d_splice_alias. So we safely go that way to get to its underlying dentry. Cc: stable@vger.kernel.org # since 2009 or so Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit e72b9dd6 upstream. lower_dentry can't go from positive to negative (we have it pinned), but it *can* go from negative to positive. So fetching ->d_inode into a local variable, doing a blocking allocation, checking that now ->d_inode is non-NULL and feeding the value we'd fetched earlier to a function that won't accept NULL is not a good idea. Cc: stable@vger.kernel.org Signed-off-by:
-
Hans de Goede authored
commit 7574c0db upstream. Many cheap devices use Silead touchscreen controllers. Testing has shown repeatedly that these touchscreen controllers work fine at 400KHz, but for unknown reasons do not work properly at 100KHz. This has been seen on both ARM and x86 devices using totally different i2c controllers. On some devices the ACPI tables list another device at the same I2C-bus as only being capable of 100KHz, testing has shown that these other devices work fine at 400KHz (as can be expected of any recent I2C hw). This commit makes i2c_acpi_find_bus_speed() always return 400KHz if a Silead touchscreen controller is present, fixing the touchscreen not working on devices which ACPI tables' wrongly list another device on the same bus as only being capable of 100KHz. Specifically this fixes the touchscreen on the Jumper EZpad 6 m4 not working. Reported-by:
youling 257 <youling257@gmail.com> Tested-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> [wsa: rewording warning a little] Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Signed-off-by:
-
Mike Marciniszyn authored
commit 22bb1365 upstream. There is no reason for a different pad buffer for the two packet types. Expand the current buffer allocation to allow for both packet types. Fixes: f8195f3b ("IB/hfi1: Eliminate allocation while atomic") Reported-by:
Kaike Wan <kaike.wan@intel.com> Reviewed-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
James Erwin authored
commit a9c3c4c5 upstream. If an hfi1 card is inserted in a Gen4 systems, the driver will avoid the gen3 speed bump and the card will operate at half speed. This is because the driver avoids the gen3 speed bump when the parent bus speed isn't identical to gen3, 8.0GT/s. This is not compatible with gen4 and newer speeds. Fix by relaxing the test to explicitly look for the lower capability speeds which inherently allows for gen4 and all future speeds. Fixes: 77241056 ("IB/hfi1: add driver files") Link: https://lore.kernel.org/r/20191101192059.106248.1699.stgit@awfm-01.aw.intel.com Cc: <stable@vger.kernel.org> Reviewed-by:
James Erwin <james.erwin@intel.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Chuhong Yuan authored
commit ba60cf9f upstream. The driver forgets to destroy workqueue in remove() similarly to what is done when probe() fails. Add a call to destroy_workqueue() to fix it. Since unregistration will wait for the work to finish, we do not need to cancel/flush the work instance in remove(). Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191114023405.31477-1-hslester96@gmail.comSigned-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Lucas Stach authored
commit 549766ac upstream. The driver for F54 just polls the status and doesn't even have a IRQ handler registered. Make sure to disable all F54 IRQs, so we don't crash the kernel on a nonexistent handler. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Link: https://lore.kernel.org/r/20191105114402.6009-1-l.stach@pengutronix.de Cc: stable@vger.kernel.org Signed-off-by:
-
Andrew Duggan authored
commit 5d40d95e upstream. Currently, rmi_f11_attention() and rmi_f12_attention() functions update the attn_data data pointer and size based on the size of the expected size of the attention data. However, if the actual valid data in the attn buffer is less then the expected value then the updated data pointer will point to memory beyond the end of the attn buffer. Using the calculated valid_bytes instead will prevent this from happening. Signed-off-by:
Andrew Duggan <aduggan@synaptics.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191025002527.3189-3-aduggan@synaptics.comSigned-off-by:
-
Andrew Duggan authored
commit f6aabe1f upstream. This patch fixes an issue seen on HID touchpads which report finger positions using RMI4 Function 12. The issue manifests itself as spurious button presses as described in: https://www.spinics.net/lists/linux-input/msg58618.html Commit 24d28e4f ("Input: synaptics-rmi4 - convert irq distribution to irq_domain") switched the RMI4 driver to using an irq_domain to handle RMI4 function interrupts. Functions with more then one interrupt now have each interrupt mapped to their own IRQ and IRQ handler. The result of this change is that the F12 IRQ handler was now getting called twice. Once for the absolute data interrupt and once for the relative data interrupt. For HID devices, calling rmi_f12_attention() a second time causes the attn_data data pointer and size to be set incorrectly. When the touchpad button is pressed, F30 will generate an interrupt and attempt to read the F30 data from the invalid attn_data data pointer and report incorrect button events. This patch disables the F12 relative interrupt which prevents rmi_f12_attention() from being called twice. Signed-off-by:
Simon Wood <simon@mungewell.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191025002527.3189-2-aduggan@synaptics.comSigned-off-by:
-
Lucas Stach authored
commit 003f01c7 upstream. The video buffer used by the queue is a vb2_v4l2_buffer, not a plain vb2_buffer. Using the wrong type causes the allocation of the buffer storage to be too small, causing a out of bounds write when __init_vb2_v4l2_buffer initializes the buffer. Signed-off-by:
-
