- 19 Jan, 2016 5 commits
-
-
Jonas Jonsson authored
commit f33a7f72 upstream. Some modems, such as the Telit UE910, are using an Infineon Flash Loader utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC Data). The latter can be used as a serial interface to upgrade the firmware of the modem. However, that isn't possible when the cdc-acm driver takes control of the device. The following is an explanation of the behaviour by Daniele Palmas during discussion on linux-usb. "This is what happens when the device is turned on (without modifying the drivers): [155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci [155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11 [155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041 [155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device This is the flashing device that is caught by the cdc-acm driver. Once the ttyACM appears, the application starts sending a magic string (simple write on the file descriptor) to keep the device in flashing mode. If this magic string is not properly received in a certain time interval, the modem goes on in normal operative mode: [155493.748094] usb 1-3: USB disconnect, device number 27 [155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci [155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021 [155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM [155495.059989] usb 1-3: Manufacturer: Telit [155495.059992] usb 1-3: SerialNumber: 359658044004697 [155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device [155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device [155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device [155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device [155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device [155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device [155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14 Using the cdc-acm driver, the string, though being sent in the same way than using the usb-serial-simple driver (I can confirm that the data is passing properly since I used an hw usb sniffer), does not make the device to stay in flashing mode." Signed-off-by:
Jonas Jonsson <jonas@ludd.ltu.se> Tested-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Konstantin Shkolnyy authored
commit 7c90e610 upstream. CP2110 ID (0x10c4, 0xea80) doesn't belong here because it's a HID and completely different from CP210x devices. Signed-off-by:
Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com> Signed-off-by:
-
Dan Carpenter authored
commit 231bfe53 upstream. WARN_ON() only takes a condition argument. I have changed these to WARN() instead. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Felipe Balbi authored
commit 391e6dcb upstream. pxa27x disconnects pullups on suspend but doesn't notify the gadget driver about it, so gadget driver can't disable the endpoints it was using. This causes problems on resume because gadget core will think endpoints are still enabled and just ignore the following usb_ep_enable(). Fix this problem by calling gadget_driver->disconnect(). Tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Roman Gushchin authored
commit 3ca8138f upstream. I got a report about unkillable task eating CPU. Further investigation shows, that the problem is in the fuse_fill_write_pages() function. If iov's first segment has zero length, we get an infinite loop, because we never reach iov_iter_advance() call. Fix this by calling iov_iter_advance() before repeating an attempt to copy data from userspace. A similar problem is described in 124d3b70 ("fix writev regression: pan hanging unkillable and un-straceable"). If zero-length segmend is followed by segment with invalid address, iov_iter_fault_in_readable() checks only first segment (zero-length), iov_iter_copy_from_user_atomic() skips it, fails at second and returns zero -> goto again without skipping zero-length segment. Patch calls iov_iter_advance() before goto again: we'll skip zero-length segment at second iteraction and iov_iter_fault_in_readable() will detect invalid address. Special thanks to Konstantin Khlebnikov, who helped a lot with the commit description. Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Maxim Patlasov <mpatlasov@parallels.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by:
Roman Gushchin <klamm@yandex-team.ru> Signed-off-by:
Miklos Szeredi <miklos@szeredi.hu> Fixes: ea9b9907 ("fuse: implement perform_write") Signed-off-by:
-
- 14 Jan, 2016 1 commit
-
-
Ingo Molnar authored
commit 23a0d4e8 upstream. Tapasweni Pathak reported that we do a kmalloc() in efi_call_phys_prolog() on x86-64 while having interrupts disabled, which is a big no-no, as kmalloc() can sleep. Solve this by removing the irq disabling from the prolog/epilog calls around EFI calls: it's unnecessary, as in this stage we are single threaded in the boot thread, and we don't ever execute this from interrupt contexts. Reported-by:
Tapasweni Pathak <tapaswenipathak@gmail.com> Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
Matt Fleming <matt.fleming@intel.com> Cc: Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
- 06 Jan, 2016 24 commits
-
-
Kamal Mostafa authored
commit f6ba98c5 upstream. Signed-off-by:
Pavel Machek <pavel@ucw.cz> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Pali Rohar <pali.rohar@gmail.com> Cc: Roberta Dobrescu <roberta.dobrescu@gmail.com> Link: http://lkml.kernel.org/r/1447280736-2161-2-git-send-email-kamal@canonical.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> [ kamal: backport to 3.19-stable: build all tools for this version ] Signed-off-by:
-
Andrew Honig authored
commit 0185604c upstream. Currently if userspace restores the pit counters with a count of 0 on channels 1 or 2 and the guest attempts to read the count on those channels, then KVM will perform a mod of 0 and crash. This will ensure that 0 values are converted to 65536 as per the spec. This is CVE-2015-7513. Signed-off-by:
Andy Honig <ahonig@google.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
David Howells authored
commit b4a1b4f5 upstream. This fixes CVE-2015-7550. There's a race between keyctl_read() and keyctl_revoke(). If the revoke happens between keyctl_read() checking the validity of a key and the key's semaphore being taken, then the key type read method will see a revoked key. This causes a problem for the user-defined key type because it assumes in its read method that there will always be a payload in a non-revoked key and doesn't check for a NULL pointer. Fix this by making keyctl_read() check the validity of a key after taking semaphore instead of before. I think the bug was introduced with the original keyrings code. This was discovered by a multithreaded test program generated by syzkaller (http://github.com/google/syzkaller). Here's a cleaned up version: #include <sys/types.h> #include <keyutils.h> #include <pthread.h> void *thr0(void *arg) { key_serial_t key = (unsigned long)arg; keyctl_revoke(key); return 0; } void *thr1(void *arg) { key_serial_t key = (unsigned long)arg; char buffer[16]; keyctl_read(key, buffer, 16); return 0; } int main() { key_serial_t key = add_key("user", "%", "foo", 3, KEY_SPEC_USER_KEYRING); pthread_t th[5]; pthread_create(&th[0], 0, thr0, (void *)(unsigned long)key); pthread_create(&th[1], 0, thr1, (void *)(unsigned long)key); pthread_create(&th[2], 0, thr0, (void *)(unsigned long)key); pthread_create(&th[3], 0, thr1, (void *)(unsigned long)key); pthread_join(th[0], 0); pthread_join(th[1], 0); pthread_join(th[2], 0); pthread_join(th[3], 0); return 0; } Build as: cc -o keyctl-race keyctl-race.c -lkeyutils -lpthread Run as: while keyctl-race; do :; done as it may need several iterations to crash the kernel. The crash can be summarised as: BUG: unable to handle kernel NULL pointer dereference at 0000000000000010 IP: [<ffffffff81279b08>] user_read+0x56/0xa3 ... Call Trace: [<ffffffff81276aa9>] keyctl_read_key+0xb6/0xd7 [<ffffffff81277815>] SyS_keyctl+0x83/0xe0 [<ffffffff815dbb97>] entry_SYSCALL_64_fastpath+0x12/0x6f Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
David Howells <dhowells@redhat.com> Tested-by:
James Morris <james.l.morris@oracle.com> Signed-off-by:
-
Rainer Weikusat authored
[ Upstream commit 3822b5c2 ] With b3ca9b02, the AF_UNIX SOCK_STREAM receive code was changed from using mutex_lock(&u->readlock) to mutex_lock_interruptible(&u->readlock) to prevent signals from being delayed for an indefinite time if a thread sleeping on the mutex happened to be selected for handling the signal. But this was never a problem with the stream receive code (as opposed to its datagram counterpart) as that never went to sleep waiting for new messages with the mutex held and thus, wouldn't cause secondary readers to block on the mutex waiting for the sleeping primary reader. As the interruptible locking makes the code more complicated in exchange for no benefit, change it back to using mutex_lock. Signed-off-by:
Rainer Weikusat <rweikusat@mobileactivedefense.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 3036facb ] fou->udp_offloads is managed by RCU. As it is actually included inside the fou sockets, we cannot let the memory go out of scope before a grace period. We either can synchronize_rcu or switch over to kfree_rcu to manage the sockets. kfree_rcu seems appropriate as it is used by vxlan and geneve. Fixes: 23461551 ("fou: Support for foo-over-udp RX path") Cc: Tom Herbert <tom@herbertland.com> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 5233252f ] Signed-off-by:
-
WANG Cong authored
[ Upstream commit 09ccfd23 ] Reported-by:
Dmitry Vyukov <dvyukov@gmail.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit f6548615 ] skb_reorder_vlan_header is called after the vlan header has been pulled. As a result the offset of the begining of the mac header has been incrased by 4 bytes (VLAN_HLEN). When moving the mac addresses, include this incrase in the offset calcualation so that the mac addresses are copied correctly. Fixes: a6e18ff1 (vlan: Fix untag operations of stacked vlans with REORDER_HEADER off) CC: Nicolas Dichtel <nicolas.dichtel@6wind.com> CC: Patrick McHardy <kaber@trash.net> Signed-off-by:
Vladislav Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit a6e18ff1 ] When we have multiple stacked vlan devices all of which have turned off REORDER_HEADER flag, the untag operation does not locate the ethernet addresses correctly for nested vlans. The reason is that in case of REORDER_HEADER flag being off, the outer vlan headers are put back and the mac_len is adjusted to account for the presense of the header. Then, the subsequent untag operation, for the next level vlan, always use VLAN_ETH_HLEN to locate the begining of the ethernet header and that ends up being a multiple of 4 bytes short of the actuall beginning of the mac header (the multiple depending on the how many vlan encapsulations ethere are). As a reslult, if there are multiple levles of vlan devices with REODER_HEADER being off, the recevied packets end up being dropped. To solve this, we use skb->mac_len as the offset. The value is always set on receive path and starts out as a ETH_HLEN. The value is also updated when the vlan header manupations occur so we know it will be correct. Signed-off-by:
Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 5037e9ef ] David Wilder reported crashes caused by dst reuse. <quote David> I am seeing a crash on a distro V4.2.3 kernel caused by a double release of a dst_entry. In ipv4_dst_destroy() the call to list_empty() finds a poisoned next pointer, indicating the dst_entry has already been removed from the list and freed. The crash occurs 18 to 24 hours into a run of a network stress exerciser. </quote> Thanks to his detailed report and analysis, we were able to understand the core issue. IP early demux can associate a dst to skb, after a lookup in TCP/UDP sockets. When socket cache is not properly set, we want to store into sk->sk_dst_cache the dst for future IP early demux lookups, by acquiring a stable refcount on the dst. Problem is this acquisition is simply using an atomic_inc(), which works well, unless the dst was queued for destruction from dst_release() noticing dst refcount went to zero, if DST_NOCACHE was set on dst. We need to make sure current refcount is not zero before incrementing it, or risk double free as David reported. This patch, being a stable candidate, adds two new helpers, and use them only from IP early demux problematic paths. It might be possible to merge in net-next skb_dst_force() and skb_dst_force_safe(), but I prefer having the smallest patch for stable kernels : Maybe some skb_dst_force() callers do not expect skb->dst can suddenly be cleared. Can probably be backported back to linux-3.6 kernels Reported-by:
David J. Wilder <dwilder@us.ibm.com> Tested-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Sergei Shtylyov authored
[ Upstream commit 248be83d ] In a low memory situation the following kernel oops occurs: Unable to handle kernel NULL pointer dereference at virtual address 00000050 pgd = 8490c000 [00000050] *pgd=4651e831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT ARM Modules linked in: CPU: 0 Not tainted (3.4-at16 #9) PC is at skb_put+0x10/0x98 LR is at sh_eth_poll+0x2c8/0xa10 pc : [<8035f780>] lr : [<8028bf50>] psr: 60000113 sp : 84eb1a90 ip : 84eb1ac8 fp : 84eb1ac4 r10: 0000003f r9 : 000005ea r8 : 00000000 r7 : 00000000 r6 : 940453b0 r5 : 00030000 r4 : 9381b180 r3 : 00000000 r2 : 00000000 r1 : 000005ea r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 10c53c7d Table: 4248c059 DAC: 00000015 Process klogd (pid: 2046, stack limit = 0x84eb02e8) [...] This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left NULL but sh_eth_rx() later uses it without checking. Add such check... Reported-by:
Yasushi SHOJI <yashi@atmark-techno.com> Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 79462ad0 ] 郭永刚 reported that one could simply crash the kernel as root by using a simple program: int socket_fd; struct sockaddr_in addr; addr.sin_port = 0; addr.sin_addr.s_addr = INADDR_ANY; addr.sin_family = 10; socket_fd = socket(10,3,0x40000000); connect(socket_fd , &addr,16); AF_INET, AF_INET6 sockets actually only support 8-bit protocol identifiers. inet_sock's skc_protocol field thus is sized accordingly, thus larger protocol identifiers simply cut off the higher bits and store a zero in the protocol fields. This could lead to e.g. NULL function pointer because as a result of the cut off inet_num is zero and we call down to inet_autobind, which is NULL for raw sockets. kernel: Call Trace: kernel: [<ffffffff816db90e>] ? inet_autobind+0x2e/0x70 kernel: [<ffffffff816db9a4>] inet_dgram_connect+0x54/0x80 kernel: [<ffffffff81645069>] SYSC_connect+0xd9/0x110 kernel: [<ffffffff810ac51b>] ? ptrace_notify+0x5b/0x80 kernel: [<ffffffff810236d8>] ? syscall_trace_enter_phase2+0x108/0x200 kernel: [<ffffffff81645e0e>] SyS_connect+0xe/0x10 kernel: [<ffffffff81779515>] tracesys_phase2+0x84/0x89 I found no particular commit which introduced this problem. CVE: CVE-2015-8543 Cc: Cong Wang <cwang@twopensource.com> Reported-by:
郭永刚 <guoyonggang@360.cn> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 9470e24f ] SCTP is lacking proper np->opt cloning at accept() time. TCP and DCCP use ipv6_dup_options() helper, do the same in SCTP. We might later factorize this code in a common helper to avoid future mistakes. Reported-by:
-
Stefan Wahren authored
[ Upstream commit ed7d42e2 ] In case of a tx queue timeout every transmit is blocked until the QCA7000 resets himself and triggers a sync which makes the driver flushs the tx ring. So avoid this blocking situation by triggering the sync immediately after the timeout. Waking the queue doesn't make sense in this situation. Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06e ("net: qualcomm: new Ethernet over SPI driver for QCA7000") Signed-off-by:
-
Marcelo Ricardo Leitner authored
[ Upstream commit 50a5ffb1 ] As we are keeping timestamps on when copying the socket, we also have to copy sk_tsflags. This is needed since b9f40e21 ("net-timestamp: move timestamp flags out of sk_flags"). Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
-
Marcelo Ricardo Leitner authored
[ Upstream commit 01ce63c9 ] Dmitry Vyukov reported that SCTP was triggering a WARN on socket destroy related to disabling sock timestamp. When SCTP accepts an association or peel one off, it copies sock flags but forgot to call net_enable_timestamp() if a packet timestamping flag was copied, leading to extra calls to net_disable_timestamp() whenever such clones were closed. The fix is to call net_enable_timestamp() whenever we copy a sock with that flag on, like tcp does. Reported-by:
-
Marcelo Ricardo Leitner authored
[ Upstream commit cb5e173e ] SCTP echoes a cookie o INIT ACK chunks that contains a timestamp, for detecting stale cookies. This cookie is echoed back to the server by the client and then that timestamp is checked. Thing is, if the listening socket is using packet timestamping, the cookie is encoded with ktime_get() value and checked against ktime_get_real(), as done by __net_timestamp(). The fix is to sctp also use ktime_get_real(), so we can compare bananas with bananas later no matter if packet timestamping was enabled or not. Fixes: 52db882f ("net: sctp: migrate cookie life from timeval to ktime") Signed-off-by:
-
Pavel Machek authored
[ Upstream commit f2a3771a ] atl1c driver is doing order-4 allocation with GFP_ATOMIC priority. That often breaks networking after resume. Switch to GFP_KERNEL. Still not ideal, but should be significantly better. atl1c_setup_ring_resources() is called from .open() function, and already uses GFP_KERNEL, so this change is safe. Signed-off-by:
Michal Hocko <mhocko@suse.com> Signed-off-by:
-
Nicolas Dichtel authored
[ Upstream commit 6a61d4db ] Parameters were updated only if the kernel was unable to find the tunnel with the new parameters, ie only if core pamareters were updated (keys, addr, link, type). Now it's possible to update ttl, hoplimit, flowinfo and flags. Fixes: c12b395a ("gre: Support GRE over IPv6") Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
WANG Cong authored
commit 7ba0c47c upstream. We need to wait for the flying timers, since we are going to free the mrtable right after it. Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Vineet Gupta authored
commit 30b9dbee upstream. Signed-off-by:
-
Peter Zijlstra authored
commit dfd01f02 upstream. Jan Stancek reported that I wrecked things for him by fixing things for Vladimir :/ His report was due to an UNINTERRUPTIBLE wait getting -EINTR, which should not be possible, however my previous patch made this possible by unconditionally checking signal_pending(). We cannot use current->state as was done previously, because the instruction after the store to that variable it can be changed. We must instead pass the initial state along and use that. Fixes: 68985633 ("sched/wait: Fix signal handling in bit wait helpers") Reported-by:
Jan Stancek <jstancek@redhat.com> Reported-by:
Chris Mason <clm@fb.com> Tested-by:
Vladimir Murzin <vladimir.murzin@arm.com> Tested-by:
Paul Turner <pjt@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: tglx@linutronix.de Cc: Oleg Nesterov <oleg@redhat.com> Cc: hpa@zytor.com Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [ kamal: backport to 3.19-stable: no pnfs_layoutget_retry_bit_wait() ] Signed-off-by:
-
Peter Zijlstra authored
commit 68985633 upstream. Vladimir reported getting RCU stall warnings and bisected it back to commit: 74316201 ("sched: Remove proliferation of wait_on_bit() action functions") That commit inadvertently reversed the calls to schedule() and signal_pending(), thereby not handling the case where the signal receives while we sleep. Reported-by:
-
Kamal Mostafa authored
This reverts commit fe4cb8a3. Not suitable for 3.19-stable: no __dso__findlink_by_longname(). Cc: Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
- 21 Dec, 2015 1 commit
-
-
Kamal Mostafa authored
Signed-off-by:
-
- 15 Dec, 2015 9 commits
-
-
Andrew Lunn authored
commit 4eba7bb1 upstream. When a multicast group is joined on a socket, a struct ip_mc_socklist is appended to the sockets mc_list containing information about the joined group. If the interface is hot unplugged, this entry becomes stale. Prior to commit 52ad353a ("igmp: fix the problem when mc leave group") it was possible to remove the stale entry by performing a IP_DROP_MEMBERSHIP, passing either the old ifindex or ip address on the interface. However, this fix enforces that the interface must still exist. Thus with time, the number of stale entries grows, until sysctl_igmp_max_memberships is reached and then it is not possible to join and more groups. The previous patch fixes an issue where a IP_DROP_MEMBERSHIP is performed without specifying the interface, either by ifindex or ip address. However here we do supply one of these. So loosen the restriction on device existence to only apply when the interface has not been specified. This then restores the ability to clean up the stale entries. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Fixes: 52ad353a "(igmp: fix the problem when mc leave group") Signed-off-by:
-
Aaro Koskinen authored
commit 3c25a860 upstream. Commit fcb26ec5 ("broadcom: move all PHY_ID's to header") updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0 with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting the original). Fix that. Fixes: fcb26ec5 ("broadcom: move all PHY_ID's to header") Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
-
Rainer Weikusat authored
[ Upstream commit 7d267278 ] Rainer Weikusat <rweikusat@mobileactivedefense.com> writes: An AF_UNIX datagram socket being the client in an n:1 association with some server socket is only allowed to send messages to the server if the receive queue of this socket contains at most sk_max_ack_backlog datagrams. This implies that prospective writers might be forced to go to sleep despite none of the message presently enqueued on the server receive queue were sent by them. In order to ensure that these will be woken up once space becomes again available, the present unix_dgram_poll routine does a second sock_poll_wait call with the peer_wait wait queue of the server socket as queue argument (unix_dgram_recvmsg does a wake up on this queue after a datagram was received). This is inherently problematic because the server socket is only guaranteed to remain alive for as long as the client still holds a reference to it. In case the connection is dissolved via connect or by the dead peer detection logic in unix_dgram_sendmsg, the server socket may be freed despite "the polling mechanism" (in particular, epoll) still has a pointer to the corresponding peer_wait queue. There's no way to forcibly deregister a wait queue with epoll. Based on an idea by Jason Baron, the patch below changes the code such that a wait_queue_t belonging to the client socket is enqueued on the peer_wait queue of the server whenever the peer receive queue full condition is detected by either a sendmsg or a poll. A wake up on the peer queue is then relayed to the ordinary wait queue of the client socket via wake function. The connection to the peer wait queue is again dissolved if either a wake up is about to be relayed or the client socket reconnects or a dead peer is detected or the client socket is itself closed. This enables removing the second sock_poll_wait from unix_dgram_poll, thus avoiding the use-after-free, while still ensuring that no blocked writer sleeps forever. Signed-off-by:
Jason Baron <jbaron@akamai.com> Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 4c698046 ] Similar to ipv4, when destroying an mrt table the static mfc entries and the static devices are kept, which leads to devices that can never be destroyed (because of refcnt taken) and leaked memory. Make sure that everything is cleaned up on netns destruction. Fixes: 8229efda ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code") CC: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by:
Cong Wang <cwang@twopensource.com> Signed-off-by:
-
Sasha Levin authored
commit 119d6f6a upstream. Because wakeups can (fundamentally) be late, a task might not be in the expected state. Therefore testing against a task's state is racy, and can yield false positives. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Konstantin Khlebnikov authored
commit 6adc5fd6 upstream. Proxy entries could have null pointer to net-device. Signed-off-by:
Konstantin Khlebnikov <koct9i@gmail.com> Fixes: 84920c14 ("net: Allow ipv6 proxies and arp proxies be shown with iproute2") Signed-off-by:
-
Marcin Wojtas authored
commit dc1aadf6 upstream. A value originally defined in the driver was inappropriate. Even though the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16] are reserved and read-only. This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with the controller's documentation. Signed-off-by:
Marcin Wojtas <mw@semihalf.com> Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by:
-
Marcin Wojtas authored
commit e5bdf689 upstream. MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer allocation was mistakenly set as BIT(1). This commit fixes the assignment. Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by:
-
Marcin Wojtas authored
commit db6ba9a5 upstream. This commit adds missing configuration of MBUS windows access protection in mvneta_conf_mbus_windows function - a dedicated variable for that purpose remained there unused since v3.8 initial mvneta support. Because of that the register contents were inherited from the bootloader. Signed-off-by:
-
