When the ipv6 fib changes during a table dump, the walk is
restarted and the number of nodes dumped are skipped. But the existing
code doesn't advance to the next node after a node is skipped. This can
cause the dump to loop or produce lots of duplicates when the fib
is modified during the dump.

This change advances the walk to the next node if the current node is
skipped after a restart.
Signed-off-by: Kumar Sundararajan <kumar@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Gibson says:

====================
Fix problems with with IFLA_VF_PORTS (v2)

I've had a customer encounter a problem with getifaddrs(3) freezing up
on a system with a Cisco enic device.

I've discovered that the problem is caused by an enic device with a
large number of SR-IOV virtual functions overflowing the normal sized
packet buffer for netlink, leading to interfaces not being reported
from an RTM_GETLINK request.

The first patch here just makes the problem easier to locate if it
occurs again in a different way, by adding a WARN_ON() when we run out
of room in a netlink packet in this manner.

The second patch actually fixes the problem, by only reporting
IFLA_VF_PORTS information when the RTEXT_FILTER_VF flag is specified.

v2: Corrected some CodingStyle problems
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since 115c9b81 (rtnetlink: Fix problem with
buffer allocation), RTM_NEWLINK messages only contain the IFLA_VFINFO_LIST
attribute if they were solicited by a GETLINK message containing an
IFLA_EXT_MASK attribute with the RTEXT_FILTER_VF flag.

That was done because some user programs broke when they received more data
than expected - because IFLA_VFINFO_LIST contains information for each VF
it can become large if there are many VFs.

However, the IFLA_VF_PORTS attribute, supplied for devices which implement
ndo_get_vf_port (currently the 'enic' driver only), has the same problem.
It supplies per-VF information and can therefore become large, but it is
not currently conditional on the IFLA_EXT_MASK value.

Worse, it interacts badly with the existing EXT_MASK handling.  When
IFLA_EXT_MASK is not supplied, the buffer for netlink replies is fixed at
NLMSG_GOODSIZE.  If the information for IFLA_VF_PORTS exceeds this, then
rtnl_fill_ifinfo() returns -EMSGSIZE on the first message in a packet.
netlink_dump() will misinterpret this as having finished the listing and
omit data for this interface and all subsequent ones.  That can cause
getifaddrs(3) to enter an infinite loop.

This patch addresses the problem by only supplying IFLA_VF_PORTS when
IFLA_EXT_MASK is supplied with the RTEXT_FILTER_VF flag set.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without IFLA_EXT_MASK specified, the information reported for a single
interface in response to RTM_GETLINK is expected to fit within a netlink
packet of NLMSG_GOODSIZE.

If it doesn't, however, things will go badly wrong,  When listing all
interfaces, netlink_dump() will incorrectly treat -EMSGSIZE on the first
message in a packet as the end of the listing and omit information for
that interface and all subsequent ones.  This can cause getifaddrs(3) to
enter an infinite loop.

This patch won't fix the problem, but it will WARN_ON() making it easier to
track down what's going wrong.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/netfilter/nfnetlink.c: In function ‘nfnetlink_rcv’:
net/netfilter/nfnetlink.c:371:14: warning: unused variable ‘net’ [-Wunused-variable]
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric W. Biederman says:

====================
netlink: Preventing abuse when passing file descriptors.

Andy Lutomirski when looking at the networking stack noticed that it is
possible to trick privilged processes into calling write on a netlink
socket and send netlink messages they did not intend.

In particular from time to time there are suid applications that will
write to stdout or stderr without checking exactly what kind of file
descriptors those are and can be tricked into acting as a limited form
of suid cat.  In other conversations the magic string CVE-2014-0181 has
been used to talk about this issue.

This patchset cleans things up a bit, adds some clean abstractions that
when used prevent this kind of problem and then finally changes all of
the handlers of netlink messages that I could find that call capable to
use netlink_ns_capable or an appropriate wrapper.

The abstraction netlink_ns_capable verifies that the original creator of
the netlink socket a message is sent from had the necessary capabilities
as well as verifying that the current sender of a netlink packet has the
necessary capabilities.

The idea is to prevent file descriptor passing of any form from
resulting in a file descriptor that can do more than it can for the
creator of the file descriptor.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible by passing a netlink socket to a more privileged
executable and then to fool that executable into writing to the socket
data that happens to be valid netlink message to do something that
privileged executable did not intend to do.

To keep this from happening replace bare capable and ns_capable calls
with netlink_capable, netlink_net_calls and netlink_ns_capable calls.
Which act the same as the previous calls except they verify that the
opener of the socket had the desired permissions as well.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink_net_capable - The common case use, for operations that are safe on a network namespace
netlink_capable - For operations that are only known to be safe for the global root
netlink_ns_capable - The general case of capable used to handle special cases

__netlink_ns_capable - Same as netlink_ns_capable except taking a netlink_skb_parms instead of
		       the skbuff of a netlink message.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk_net_capable - The common case, operations that are safe in a network namespace.
sk_capable - Operations that are not known to be safe in a network namespace
sk_ns_capable - The general case for special cases.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The permission check in sock_diag_put_filterinfo is wrong, and it is so removed
from it's sources it is not clear why it is wrong.  Move the computation
into packet_diag_dump and pass a bool of the result into sock_diag_filterinfo.

This does not yet correct the capability check but instead simply moves it to make
it clear what is going on.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink_capable is a static internal function in af_netlink.c and we
have better uses for the name netlink_capable.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a seg fault on 'ethtool -A' entry if the
interface is down.  Obviously we need to have the
phy device initialized / "connected" (see of_phy_connect())
to be able to advertise pause frame capabilities.

Fixes: 23402bddSigned-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shahed Shaikh says:

====================
qlcnic: Bug fixes

This patch series contains following fixes -

* Fix memory leak caused because of issuing mailbox
  command which can not wait for its completion.
* Reset firmware API lock which might be in inconsistent state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

o In case QLC_83XX_MBX_CMD_NO_WAIT command type the calling
  function does not free the memory as it does not wait for
  response. So free it when get a response from adapter after
  sending the command.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some firmware versions fails to reset the lock during
initialization. Force reset firmware API lock during driver
probe to ensure lock availability.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two breaks missing there. The result is that userspace
receives multiple messages which might be confusing.

Introduced-by: 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

I was told that the Cadence macb driver is also useful on Microblaze.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Redefine some macros that were conditioned upon SMC_DEBUG level.

By allowing compiler to verify parameters used by these macros
unconditionally, we can flag compilation failures.

Compiler will still optimize out the unused code path depending on
SMC_DEBUG, so this is a net gain.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

exisiting BPF verifier allows uninitialized access to registers,
'ret A' is considered to be a valid filter.
So initialize A and X to zero to prevent leaking kernel memory
In the future BPF verifier will be rejecting such filters
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The goal of this patch is to fix rtnelink notification. The main problem was
about notification for fdb entry with more than one remote. Before the patch,
when a remote was added to an existing fdb entry, the kernel advertised the
first remote instead of the added one. Also when a remote was removed from a fdb
entry with several remotes, the deleted remote was not advertised.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ksz9021_load_values_from_of() val2 to val4 aren't tested against their
initialization value.
This causes the test to always succeed, and this value to be used as if it
was loaded from the devicetree instead of being ignored, in case of a
missing/invalid property in the ethernet OF device node.
As a result, the value "0" is written to the relevant registers.

Change the conditions to test against the right initialization value.
Signed-off-by: Hubert Chaumette <hchaumette@adeneo-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A label just before a brace needs a following semicolon (empty statement).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

When SMC_DEBUG >= 2, we hit the following compilation error:

drivers/net/ethernet/smsc/smc91x.c:85:0:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_findirq’:
drivers/net/ethernet/smsc/smc91x.c:1784:9: error: ‘dev’ undeclared (first use in this function)
  DBG(2, dev, "%s: %s\n", CARDNAME, __func__);
         ^
Fix it by passing in the appropriate netdev pointer.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds phy_found error path when there is no phy device
and changes bus_name.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves cksum_ctl to tx_rd_des23 from cksum_pktlen for correct checksum
offloading and modifies size for Tx/Rx descriptor.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Execute "ethtool -L eth0 combined 0" in guest, if multiqueue
is enabled, virtnet_send_command() will return -EINVAL error,
there is a validation in QEMU.

But if multiqueue is disabled, virtnet_set_queues() will just
return zero (success). We should return error for this situation.
Signed-off-by: Amos Kong <akong@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MAC address retrieved from dt was not actually written to the
hardware. This meant proper communication was only possible after
changing the MAC address.

Fix that by always writing the mac address during probing.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The caller needs capabilities on the namespace being queried, not on
their own namespace.  This is a security bug, although it likely has
only a minor impact.

Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mail address for Siva Reddy Kallam is bouncing, remove the email
address from the MAINTAINERS entry for Samsung's SXGBE driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to e1000e, igb, ixgbe and i40e.

Most notably are Jakub's patches to clean up the Rx time stamping
code for ixgbe and the fix up of debug messages with proper termination.

Jesse's i40e patch fixes an issue reported by Eric Dumazet that the
i40e driver was allowing the hardware to replicate the PSH flag on
all segments of a TSO operation.  With this fix, we are now configuring
the CWR bit to only be set in the first packet of a TSO and we
enable TSO_ECN in order to advertise to the stack that we do the right
thing on the wire.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 fix from Ingo Molnar:
 "This fixes the preemption-count imbalance crash reported by Owen
  Kibel"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce: Fix CMCI preemption bugs

Pull scheduler fixes from Ingo Molnar:
 "Two fixes:

   - a SCHED_DEADLINE task selection fix
   - a sched/numa related lockdep splat fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Check for stop task appearance when balancing happens
  sched/numa: Fix task_numa_free() lockdep splat

Pull perf fixes from Ingo Molnar:
 "Two kernel side fixes:

   - an Intel uncore PMU driver potential crash fix
   - a kprobes/perf-call-graph interaction fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Use rdmsrl_safe() when initializing RAPL PMU
  kprobes/x86: Fix page-fault handling logic

Pull drm fixes from Dave Airlie:
 "Unfortunately this contains no easter eggs, its a bit larger than I'd
  like, but I included a patch that just moves code from one file to
  another and I'd like to avoid merge conflicts with that later, so it
  makes it seem worse than it is,

  Otherwise:
   - radeon: fixes to use new microcode to stabilise some cards, use
     some common displayport code, some runtime pm fixes, pll regression
     fixes
   - i915: fix for some context oopses, a warn in a used path, backlight
     fixes
   - nouveau: regression fix
   - omap: a bunch of fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (51 commits)
  drm: bochs: drop unused struct fields
  drm: bochs: add power management support
  drm: cirrus: add power management support
  drm: Split out drm_probe_helper.c from drm_crtc_helper.c
  drm/plane-helper: Don't fake-implement primary plane disabling
  drm/ast: fix value check in cbr_scan2
  drm/nouveau/bios: fix a bit shift error introduced by 457e77b2
  drm/radeon/ci: make sure mc ucode is loaded before checking the size
  drm/radeon/si: make sure mc ucode is loaded before checking the size
  drm/radeon: improve PLL params if we don't match exactly v2
  drm/radeon: memory leak on bo reservation failure. v2
  drm/radeon: fix VCE fence command
  drm/radeon: re-enable mclk dpm on R7 260X asics
  drm/radeon: add support for newer mc ucode on CI (v2)
  drm/radeon: add support for newer mc ucode on SI (v2)
  drm/radeon: apply more strict limits for PLL params v2
  drm/radeon: update CI DPM powertune settings
  drm/radeon: fix runpm handling on APUs (v4)
  drm/radeon: disable mclk dpm on R7 260X
  drm/tegra: Remove gratuitous pad field
  ...

Add \n at the end of messages where missing, remove all \r.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Time stamping resources are per-interface so there is no need
to keep separate last_rx_timestamp for each Rx ring, move
last_rx_timestamp to the adapter structure.

With last_rx_timestamp inside adapter, ixgbe_ptp_rx_hwtstamp()
inline function is reduced to a single if statement so it is
no longer necessary. If statement is placed directly in
ixgbe_process_skb_fields() fixing likely/unlikely marking.

Checks for q_vector or adapter to be NULL are superfluous.

Comment about taking I/O hit is a leftover from previous design.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

RQDPC on i210/i211 is R/W not ReadClear. Clear after reading.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some i2c fixes over DisplayPort.

* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
  drm/radeon: Improve vramlimit module param documentation
  drm/radeon: fix audio pin counts for DCE6+ (v2)
  drm/radeon/dp: switch to the common i2c over aux code
  drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
  drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
  drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
  drm/i915: support address only i2c-over-aux transactions
  drm/tegra: dp: Support address-only I2C-over-AUX transactions

Fix following compilation warning:
drivers/net/ethernet/intel/e1000e/netdev.c:6238:12: warning
‘e1000e_pm_thaw’ defined but not used [-Wunused-function]
 static int e1000e_pm_thaw(struct device *dev)
            ^
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>