These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.

Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.

Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

By just moving the atmel_gpio_to_irq() and calling the internal
function we can get rid of the driver calling back out into the
deprecated external consumer API.

Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Sharing the same irqchip with multiple gpiochips is not a good
practice. For instance, when installing hooks, we change the state
of the irqchip. The initial state of the irqchip for the second
gpiochip to register is then disrupted.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Smatch complains about this condition:

	if (has_config && num_pins >= 1)

The "has_config" variable is either uninitialized or true.  The
"num_pins" variable is unsigned and we verified that it is non-zero on
the lines before so we know "num_pines >= 1" is true.  Really, we could
just check "num_configs" directly and remove the "has_config" variable.

Fixes: 77618084 ("pinctrl: introduce driver for Atmel PIO4 controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

It looks like we parse the drive strength setting here, but never
actually write it into the hardware to update it. Parse the setting and
then write it at the end of the pinconf setting function so that it
actually sticks in the hardware.

Fixes: 0e948042 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode")
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/pinctrl/sirf/pinctrl-atlas7.c: In function 'atlas7_pinmux_resume_noirq':
drivers/pinctrl/sirf/pinctrl-atlas7.c:5545:6: warning:
 variable 'bank' set but not used [-Wunused-but-set-variable]
  u32 bank;

drivers/pinctrl/sirf/pinctrl-atlas7.c:5543:28: warning:
 variable 'conf' set but not used [-Wunused-but-set-variable]
  struct atlas7_pad_config *conf;
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If you look at "pinconf-groups" in debugfs for ssbi-mpp you'll notice
it looks like nonsense.

The problem is fairly well described in commit 1cf86bc2 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c828 ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-mpp has the same
problem.  Let's fix it there too.

NOTE: in case it's helpful to someone reading this, the way to tell
whether to do the -EINVAL or not is to look at the PCONFDUMP for a
given attribute.  If the last element (has_arg) is false then you need
to do the -EINVAL trick.

ALSO NOTE: it seems unlikely that the values returned when we try to
get PIN_CONFIG_BIAS_PULL_UP will actually be printed since "has_arg"
is false for that one, but I guess it's still fine to return different
values so I kept doing that.  It seems like another driver (ssbi-gpio)
uses a custom attribute (PM8XXX_QCOM_PULL_UP_STRENGTH) for something
similar so maybe a future change should do that here too.

Fixes: cfb24f6e ("pinctrl: Qualcomm SPMI PMIC MPP pin controller driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If you look at "pinconf-groups" in debugfs for ssbi-gpio you'll notice
it looks like nonsense.

The problem is fairly well described in commit 1cf86bc2 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c828 ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-gpio has the same
problem.  Let's fix it there too.

Fixes: b4c45fe9 ("pinctrl: qcom: ssbi: Family A gpio & mpp drivers")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'sh-pfc-for-v4.20-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v4.20

  - Add SATA and audio pin groups on R-Car M3-N,
  - Add EtherAVB pin groups on RZ/G1C,
  - Add PWM and display (DU) pin groups on R-Car E3,
  - Add support for the new RZ/G2M (r8a774a1) SoC.

WARN_ON() already contains an unlikely(), so it's not necessary to
wrap it into another.
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of open coding same structure definition for PM operations,
replace it with a common macro.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of open coding same structure definition for PM operations,
replace it with a common macro.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of open coding same structure definition for PM operations,
replace it with a common macro.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of open coding same structure definition for PM operations,
replace it with a common macro.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of open coding same structure definition for PM operations,
replace it with a common macro.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of open coding same structure definition for PM operations,
replace it with a common macro.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of open coding same structure definition for PM operations,
replace it with a common macro.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of open coding same structure definition for PM operations,
replace it with a common macro.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This common macro will simplify the code of pin control drivers
for Intel SoCs.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Get rid of code duplication by converting to use intel_pinctrl_probe_by_hid().

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Get rid of code duplication by converting to use intel_pinctrl_probe_by_hid().

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Introduce intel_pinctrl_probe_by_hid() internal API to simplify drivers,
which are using ACPI _HID to distinguish which SoC data needs to be used
when being probed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Get rid of code duplication by converting to use device_get_match_data().

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Get rid of code duplication by converting to use intel_pinctrl_probe_by_uid().

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Get rid of code duplication by converting to use intel_pinctrl_probe_by_uid().

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Introduce intel_pinctrl_probe_by_uid() internal API to simplify drivers,
which are using ACPI _UID to distinguish which SoC data needs to be used
when being probed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds DU pins, groups and function for the R8A77990 (E3) SoC.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The parameter 'community' had been spelled incorrectly.
Fix it here.

As a side effect it satisfies static checkers that issue
the following warnings:

drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Function parameter or member 'community' not described in 'intel_gpio_to_pin'
drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Excess function parameter 'commmunity' description in 'intel_gpio_to_pin'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 1292308 ("Missing break in switch")
Addresses-Coverity-ID: 1292309 ("Missing break in switch")
Addresses-Coverity-ID: 1309546 ("Missing break in switch")
Addresses-Coverity-ID: 1357369 ("Missing break in switch")
Addresses-Coverity-ID: 1357389 ("Missing break in switch")
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver so only include <linux/gpio/driver.h>

Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The pinctrl-ingenic driver is now handling the GPIO chips directly.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Depending on MACH_INGENIC prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add support for the JZ4725B and compatible SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This allows to read from debugfs whether the GPIOs requested are set as
input or output.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge the code of the gpio-ingenic driver into the pinctrl-ingenic
driver.

The reason behind this, is that the same hardware block handles both pin
config / muxing and GPIO.

ingenic_gpio_probe() have been marked as __init, but for the most part,
the code is the exact same as what it was in the gpio-ingenic driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

By using platform_driver_probe() instead of platform_driver_register(),
we can mark the ingenic_pinctrl_probe() function as __init.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Using postcore_initcall() makes the driver try to initialize way too
early.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The pinctrl-ingenic driver now supports the JZ4725B SoC.

Furthermore, the gpio-ingenic driver was dropped and the pinctrl-ingenic
driver is now responsible for providing the GPIO functionality.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>