- 16 Apr, 2017 19 commits
-
-
Dan Carpenter authored
There were a bunch of places in pblk_lines_init() where we didn't set an error code. And in pblk_writer_init() we accidentally return 1 instead of a correct error code, which would result in a Oops later. Fixes: 11a5d6fdf919 ("lightnvm: physical block device (pblk) target") Signed-off-by:Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Matias Bjørling <matias@cnexlabs.com> Signed-off-by:
Jens Axboe <axboe@fb.com>
-
Dan Carpenter authored
WARN_ON() takes a condition, not an error message. I slightly tweaked some conditions so hopefully it's more clear. Signed-off-by:
-
Dan Carpenter authored
These labels are reversed so we could end up dereferencing an error pointer or leaking. Fixes: 7f347ba6bb3a ("lightnvm: physical block device (pblk) target") Signed-off-by: -
Javier González authored
This patch introduces pblk, a host-side translation layer for Open-Channel SSDs to expose them like block devices. The translation layer allows data placement decisions, and I/O scheduling to be managed by the host, enabling users to optimize the SSD for their specific workloads. An open-channel SSD has a set of LUNs (parallel units) and a collection of blocks. Each block can be read in any order, but writes must be sequential. Writes may also fail, and if a block requires it, must also be reset before new writes can be applied. To manage the constraints, pblk maintains a logical to physical address (L2P) table, write cache, garbage collection logic, recovery scheme, and logic to rate-limit user I/Os versus garbage collection I/Os. The L2P table is fully-associative and manages sectors at a 4KB granularity. Pblk stores the L2P table in two places, in the out-of-band area of the media and on the last page of a line. In the cause of a power failure, pblk will perform a scan to recover the L2P table. The user data is organized into lines. A line is data striped across blocks and LUNs. The lines enable the host to reduce the amount of metadata to maintain besides the user data and makes it easier to implement RAID or erasure coding in the future. pblk implements multi-tenant support and can be instantiated multiple times on the same drive. Each instance owns a portion of the SSD - both regarding I/O bandwidth and capacity - providing I/O isolation for each case. Finally, pblk also exposes a sysfs interface that allows user-space to peek into the internals of pblk. The interface is available at /dev/block/*/pblk/ where * is the block device name exposed. This work also contains contributions from: Matias Bjørling <matias@cnexlabs.com> Simon A. F. Lund <slund@cnexlabs.com> Young Tack Jin <youngtack.jin@gmail.com> Huaicheng Li <huaicheng@cs.uchicago.edu> Signed-off-by:
Javier González <javier@cnexlabs.com> Signed-off-by:
-
Javier González authored
Convert sprintf calls to strlcpy in order to make possible buffer overflow more obvious. Signed-off-by:
-
Javier González authored
sector_t is always unsigned, therefore avoid < 0 checks on it. Signed-off-by:
-
Javier González authored
Clean unused variable on lightnvm core. Signed-off-by:
-
Javier González authored
Prefix the nvm_free static function with a missing static keyword. Signed-off-by:
-
Javier González authored
Target initialization has two responsibilities: creating the target partition and instantiating the target. This patch enables to create a factory partition (e.g., do not trigger recovery on the given target). This is useful for target development and for being able to restore the device state at any moment in time without requiring a full-device erase. Signed-off-by:
-
Javier González authored
The NVMe I/O command control bits are 16 bytes, but is interpreted as 32 bytes in the lightnvm user I/O data path. Signed-off-by:
-
Javier González authored
Reorder disk allocation such that the disk structure can be put safely. Signed-off-by:
-
Javier González authored
The dev->lun_map bits are cleared twice if an target init error occurs. First in the target clean routine, and then next in the nvm_tgt_create error function. Make sure that it is only cleared once by extending nvm_remove_tgt_devi() with a clear bit, such that clearing of bits can ignored when cleaning up a successful initialized target. Signed-off-by:
-
NeilBrown authored
mempool_alloc() cannot fail if the gfp flags allow it to sleep, and both GFP_KERNEL and GFP_NOIO allows for sleeping. So rrpc_move_valid_pages() and rrpc_make_rq() don't need to test the return value. Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
Matias Bjørling authored
The asserts in _nvme_nvm_check_size are not compiled due to the function not begin called. Make sure that it is called, and also fix the wrong sizes of asserts for nvme_nvm_addr_format, and nvme_nvm_bb_tbl, which checked for number of bits instead of bytes. Reported-by:
Scott Bauer <scott.bauer@intel.com> Signed-off-by:
-
Javier González authored
Free the reverse mapping table correctly on target tear down Signed-off-by:
-
Javier González authored
According to the OCSSD 1.2 specification, the 0x200 hint enables the media scrambler for the read/write opcode, providing that the controller has been correctly configured by the firmware. Rename the macro to represent this meaning. Signed-off-by:
-
Javier González authored
Until now erases have been submitted as synchronous commands through a dedicated erase function. In order to enable targets implementing asynchronous erases, refactor the erase path so that it uses the normal async I/O submission functions. If a target requires sync I/O, it can implement it internally. Also, adapt rrpc to use the new erase path. Signed-off-by:
-
Scott Bauer authored
There are two closely named structs in lightnvm: struct nvme_nvm_addr_format and struct nvme_addr_format. The first struct has 4 reserved bytes at the end, the second does not. (gdb) p sizeof(struct nvme_nvm_addr_format) $1 = 16 (gdb) p sizeof(struct nvm_addr_format) $2 = 12 In the nvme_nvm_identify function we memcpy from the larger struct to the smaller struct. We incorrectly pass the length of the larger struct and overflow by 4 bytes, lets not do that. Signed-off-by:
-
Christophe JAILLET authored
According to error handling in this function, it is likely that going to 'out' was expected here. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
- 14 Apr, 2017 7 commits
-
-
Dan Carpenter authored
If "scope_len" is sizeof(scope_id) then we would put the NUL terminator one space beyond the end of the buffer. Fixes: b1a951fe ("net/utils: generic inet_pton_with_scope helper") Signed-off-by:
-
Omar Sandoval authored
The Kyber I/O scheduler is an I/O scheduler for fast devices designed to scale to multiple queues. Users configure only two knobs, the target read and synchronous write latencies, and the scheduler tunes itself to achieve that latency goal. The implementation is based on "tokens", built on top of the scalable bitmap library. Tokens serve as a mechanism for limiting requests. There are two tiers of tokens: queueing tokens and dispatch tokens. A queueing token is required to allocate a request. In fact, these tokens are actually the blk-mq internal scheduler tags, but the scheduler manages the allocation directly in order to implement its policy. Dispatch tokens are device-wide and split up into two scheduling domains: reads vs. writes. Each hardware queue dispatches batches round-robin between the scheduling domains as long as tokens are available for that domain. These tokens can be used as the mechanism to enable various policies. The policy Kyber uses is inspired by active queue management techniques for network routing, similar to blk-wbt. The scheduler monitors latencies and scales the number of dispatch tokens accordingly. Queueing tokens are used to prevent starvation of synchronous requests by asynchronous requests. Various extensions are possible, including better heuristics and ionice support. The new scheduler isn't set as the default yet. Signed-off-by:
Omar Sandoval <osandov@fb.com> Signed-off-by:
-
Omar Sandoval authored
Currently, this callback is called right after put_request() and has no distinguishable purpose. Instead, let's call it before put_request() as soon as I/O has completed on the request, before we account it in blk-stat. With this, Kyber can enable stats when it sees a latency outlier and make sure the outlier gets accounted. Signed-off-by:
-
Omar Sandoval authored
blk_mq_finish_request() is required for schedulers that define their own put_request(). blk_mq_run_hw_queue() is required for schedulers that hold back requests to be run later. Signed-off-by:
-
Omar Sandoval authored
Wire up the sbitmap_get_shallow() operation to the tag code so that a caller can limit the number of tags available to it. Signed-off-by:
-
Omar Sandoval authored
This operation supports the use case of limiting the number of bits that can be allocated for a given operation. Rather than setting aside some bits at the end of the bitmap, we can set aside bits in each word of the bitmap. This means we can keep the allocation hints spread out and support sbitmap_resize() nicely at the cost of lower granularity for the allowed depth. Signed-off-by:
-
Christoph Hellwig authored
This drivers was added in 2008, but as far as a I can tell we never had a single platform that actually registered resources for the platform driver. It's also been unmaintained for a long time and apparently has a ATA mode that can be driven using the IDE/libata subsystem. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
- 11 Apr, 2017 1 commit
-
-
Jan Kara authored
When CFQ calls wbt_disable_default(), it will call blk_stat_remove_callback() to stop gathering IO statistics for the purposes of writeback throttling. Later, when request_queue is unregistered, wbt_exit() will call blk_stat_remove_callback() again which will try to delete callback from the list again and possibly cause list corruption. Fix the problem by making wbt_disable_default() called wbt_exit() which is properly guarded against being called multiple times. Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
- 10 Apr, 2017 2 commits
-
-
Bart Van Assche authored
Instead of showing the hctx state and flags as numbers, show the names of the flags. Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: Omar Sandoval <osandov@fb.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Bart Van Assche authored
Make it possible to check whether or not a block layer queue has been stopped. Make it possible to start and to run a blk-mq queue from user space. Signed-off-by:
-
- 08 Apr, 2017 11 commits
-
-
Martin K. Petersen authored
Separating discards and zeroout operations allows us to remove the LBPRZ block zeroing constraints from discards and honor the device preferences for UNMAP commands. If supported by the device, we'll also choose UNMAP over one of the WRITE SAME variants for discards. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Martin K. Petersen authored
Now that zeroout and discards are distinct operations we need to separate the policy of choosing the appropriate command. Create a zeroing_mode which can be one of: write: Zeroout assist not present, use regular WRITE writesame: Allow WRITE SAME(10/16) with a zeroed payload writesame_16_unmap: Allow WRITE SAME(16) with UNMAP writesame_10_unmap: Allow WRITE SAME(10) with UNMAP The last two are conditional on the device being thin provisioned with LBPRZ=1 and LBPWS=1 or LBPWS10=1 respectively. Whether to set the UNMAP bit or not depends on the REQ_NOUNMAP flag. And if none of the _unmap variants are supported, regular WRITE SAME will be used if the device supports it. The zeroout_mode is exported in sysfs and the detected mode for a given device can be overridden using the string constants above. With this change in place we can now issue WRITE SAME(16) with UNMAP set for block zeroing applications that require hard guarantees and logical_block_size granularity. And at the same time use the UNMAP command with the device's preferred granulary and alignment for discard operations. Signed-off-by:
-
Christoph Hellwig authored
Now that we use the proper REQ_OP_WRITE_ZEROES operation everywhere we can kill this hack. Signed-off-by:
-
Christoph Hellwig authored
It seems like DRBD assumes its on the wire TRIM request always zeroes data. Use that fact to implement REQ_OP_WRITE_ZEROES. Signed-off-by:
-
Christoph Hellwig authored
drbd always wants its discard wire operations to zero the blocks, so use blkdev_issue_zeroout with the BLKDEV_ZERO_UNMAP flag instead of reinventing it poorly. Signed-off-by:
-
Christoph Hellwig authored
Now that we have REQ_OP_WRITE_ZEROES implemented for all devices that support efficient zeroing, we can remove the call to blkdev_issue_discard. This means we only have two ways of zeroing left and can simplify the code. Signed-off-by:
-
Christoph Hellwig authored
mmc only supports discarding on large alignments, so the zeroing code would always fall back to explicit writings of zeroes. Signed-off-by:
-
Christoph Hellwig authored
rsxx only supports discarding on large alignments, so the zeroing code would always fall back to explicit writings of zeroes. Signed-off-by:
-
Christoph Hellwig authored
rbd only supports discarding on large alignments, so the zeroing code would always fall back to explicit writings of zeroes. Signed-off-by:
-
Christoph Hellwig authored
It's just a in-driver reimplementation of writing zeroes to the pages, which fails if the discards aren't page aligned. Signed-off-by:
-
Christoph Hellwig authored
It's identical to discard as hole punches will always leave us with zeroes on reads. Signed-off-by:
-
