The A711 has 1024x600 LVDS panel, with a PWM-based backlight. Add it to our
DT.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A83T has an LVDS bus that can be connected to a panel or a bridge. Add
the pinctrl group for it.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A83T has the same PWM block than the H3. Add it to our DT.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The display pipeline on the A83T is mainly composed of the mixers and
TCONs, plus various encoders.

Let's add the first mixer and TCON to the DTSI since the only board I have
can use only the LVDS output on the first TCON. The other parts will be
added eventually.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The H3/H5 SoCs have a HDMI output and a TV Composite output.

Add simplefb nodes for these outputs.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The DE2 CCU on Allwinner H5 SoC has a slightly different behavior than
the one on H3, so the compatible string is not set in the common DTSI
file.

Add the compatible string of H5 DE2 CCU in H5 DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The DE2 in H3/H5 has a clock control unit in it, and the behavior is
slightly different between H3 and H5.

Add the common parts in H3/H5 DTSI, and add the compatible string in H3
DTSI.

The compatible string of H5 DE2 CCU will be added in a separated patch.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

As we're going to add simplefb support for Allwinner SoCs with DE2, add
suitable pipeline strings in the device tree binding.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

Orange Pi R1 uses a Realtek RTL8152B USB Ethernet chip, which is easily
seen on the board but not show in the schematics. A regulator for the
power of the RTL8152B chip is hidden, which uses the same pin with the
Wi-Fi regulator on the original Orange Pi Zero.

Add this regulator back to the device tree, and bind it to USB1.
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

This patch fixes a missing ethernet 0 alisas in the devicetree on the
Nanopi M1 Plus.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The dwmac-sun8i hardware is present on the Nanopi M1.
It uses the internal PHY
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The board has a regular-sized HDMI connector, so enable the display
the pipeline and HDMI output for it.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A83T has 3 I2C controllers under the standard bus. There is one
more in the R_ block section. The pin functions for the 3 controllers
are on PH 0~6. I2C2 can also be used on pins PE14 and PE15, but these
pins can also mux the CSI (camera sensor interface) controller's
embedded I2C controller. The latter seems to be preferred in the
reference designs for I2C camera sensor access, freeing I2C2 for other
uses.

This patch adds device nodes for the three standard I2C controllers,
as well as pinmux settings for the PH pins. For I2C0 and I2C1, since
they only have one possible setting, just set them by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A83T has 3 I2S controllers. The first is multiplexed with the TDM
controller. The pins are generally connected to the codec side of the
AXP81x PMIC/codec/RTC chip. The second is free for other uses. The
third only supports output, and is connected internally to the HDMI
controller for HDMI audio output.

This patch adds device nodes for the controllers, and a default pinmux
setting for the second controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

allwinner,leds-active-low have effect only on boards which us the internal PHY.
So this patch remove it from all boards which do not use the internal PHY.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Cubietruck Plus has a Realtek RTL8211E RGMII PHY tied to the EMAC.
The AXP818 PMIC's regulators provide main power and secondary signaling
voltages to the PHY. The latter is always on, as it also supplies the
pingroup on the SoC, which has other uses.

The Bananapi M3 has a Realtek RTL8211E RGMII PHY tied to the EMAC.
The AXP818 PMIC's SW regulators provides power to the PHY.

This patch enables Ethernet with the EMAC on both these boards by
enabling the emac node and setting all the required properties.
A proper ethernet alias is added as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The dwmac-sun8i is an ethernet MAC hardware that support 10/100/1000 speed.
This patch add support for it on the Allwinner a83t SoC Device-tree.

This patch add the emac device node and the related RGMII pins node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Similarly to Orange Pi Zero, NanoPi Neo board has an USB OTG port with
an ID pin but with unpowered VBUS. This patch enables this port in
forced peripheral mode.

ohci/ehci nodes are still enabled since the host mode may work if
external power source is used. In that case, the mode can be switched
for example via sysfs. The same strategy is used for Orange Pi Zero
board DTS.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H3 SoC.
The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.

Raspberry Pi B+ like peripherals supported on this board include:

  - Power input through micro-USB connector (without USB OTG)
  - Native 100 Mbps ethernet using the internal PHY, as opposed to
    USB-based on the RPi
  - 4x USB 2.0 host ports, directly connected to the SoC, as opposed to
    being connected through a USB 2.0 hub on the RPi
  - TV and audio output on a 3.5mm TRRS jack
  - HDMI output
  - Micro-SD card slot
  - Standard RPi B+ GPIO header, with the standard peripherals routed to
    the same pins.

    * 5V, 3.3V power, and ground
    * I2C0 on the H3 is routed to I2C1 pins on the RPi header
    * I2C1 on the H3 is routed to I2C0 pins on the RPi header
    * UART1 on the H3 is routed to UART0 pins on the RPi header
    * SPI0 on the H3 is routed to SPI0 pins on the RPi header,
      with GPIO pin PA17 replacing the missing Chip Select 1
    * I2S1 on the H3 is routed to PCM pins on the RPi header

  - Additional peripherals from the H3 are available on different pins.
    These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3

In addition, there are a number of new features:

  - Console UART header
  - Consumer IR receiver
  - Camera interface (not compatible with RPi)
  - Onboard microphone
  - eMMC expansion module port
  - Heatsink mounting holes
  - Power button

The power button requires corresponding software for the embedded
coprocessor to properly function.

This patch adds a dts file for this board that enables all "onboard"
peripherals currently supported. This means no display or camera
support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

On AXP813/818, GPIO0 and GPIO1 can be used as LDO as (respectively)
ldo_io0 and ldo_io1.

Let's add the pinctrl properties to the said regulators.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This adds DT node for the GPIO/pinctrl part present in AXP813/AXP818.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Orange Pi R1 is a board design based on Orange Pi Zero, with XR819 Wi-Fi
chip replaced by RTL8189ETV Wi-Fi module and the USB Type-A jack
replaced by an onboard USB RTL8152B USB-Ethernet adapter.

Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A13 Olinuxino have an headphone jack and audio is supported
so enable it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Pull ARM fixes from Russell King:

 - LPAE fixes for kernel-readonly regions

 - Fix for get_user_pages_fast on LPAE systems

 - avoid tying decompressor to a particular platform if DEBUG_LL is
   enabled

 - BUG if we attempt to return to userspace but the to-be-restored PSR
   value keeps us in privileged mode (defeating an issue that ftracetest
   found)

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: BUG if jumping to usermode address in kernel mode
  ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
  ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
  ARM: make decompressor debug output user selectable
  ARM: fix get_user_pages_fast

Pull irq fixes from Thomas Glexiner:

 - unbreak the irq trigger type check for legacy platforms

 - a handful fixes for ARM GIC v3/4 interrupt controllers

 - a few trivial fixes all over the place

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/matrix: Make - vs ?: Precedence explicit
  irqchip/imgpdc: Use resource_size function on resource object
  irqchip/qcom: Fix u32 comparison with value less than zero
  irqchip/exiu: Fix return value check in exiu_init()
  irqchip/gic-v3-its: Remove artificial dependency on PCI
  irqchip/gic-v4: Add forward definition of struct irq_domain_ops
  irqchip/gic-v3: pr_err() strings should end with newlines
  irqchip/s3c24xx: pr_err() strings should end with newlines
  irqchip/gic-v3: Fix ppi-partitions lookup
  irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
  genirq: Track whether the trigger type has been set

Pull misc x86 fixes from Ingo Molnar:
 - topology enumeration fixes
 - KASAN fix
 - two entry fixes (not yet the big series related to KASLR)
 - remove obsolete code
 - instruction decoder fix
 - better /dev/mem sanity checks, hopefully working better this time
 - pkeys fixes
 - two ACPI fixes
 - 5-level paging related fixes
 - UMIP fixes that should make application visible faults more debuggable
 - boot fix for weird virtualization environment

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
  x86/decoder: Add new TEST instruction pattern
  x86/PCI: Remove unused HyperTransport interrupt support
  x86/umip: Fix insn_get_code_seg_params()'s return value
  x86/boot/KASLR: Remove unused variable
  x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
  x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
  x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
  x86/pkeys/selftests: Fix protection keys write() warning
  x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
  x86/mpx/selftests: Fix up weird arrays
  x86/pkeys: Update documentation about availability
  x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
  x86/smpboot: Fix __max_logical_packages estimate
  x86/topology: Avoid wasting 128k for package id array
  perf/x86/intel/uncore: Cache logical pkg id in uncore driver
  x86/acpi: Reduce code duplication in mp_override_legacy_irq()
  x86/acpi: Handle SCI interrupts above legacy space gracefully
  x86/boot: Fix boot failure when SMP MP-table is based at 0
  x86/mm: Limit mmap() of /dev/mem to valid physical addresses
  x86/selftests: Add test for mapping placement for 5-level paging
  ...

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes: a documentation fix, a Sparse warning fix and a debugging
  fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Fix task state recording/printout
  sched/deadline: Don't use dubious signed bitfields
  sched/deadline: Fix the description of runtime accounting in the documentation

Pull perf fixes from Ingo Molnar:
 "Misc fixes: two PMU driver fixes and a memory leak fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix memory leak triggered by perf --namespace
  perf/x86/intel/uncore: Add event constraint for BDX PCU
  perf/x86/intel: Hide TSX events when RTM is not supported

Pull static key fix from Ingo Molnar:
 "Fix a boot warning related to bad init ordering of the static keys
  self-test"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  jump_label: Invoke jump_label_test() via early_initcall()

Pull objtool fixes from Ingo Molnar:
 "A handful of objtool fixes, most of them related to making the UAPI
  header-syncing warnings easier to read and easier to act upon"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/headers: Sync objtool UAPI header
  objtool: Fix cross-build
  objtool: Move kernel headers/code sync check to a script
  objtool: Move synced files to their original relative locations
  objtool: Make unreachable annotation inline asms explicitly volatile
  objtool: Add a comment for the unreachable annotation macros

Detect if we are returning to usermode via the normal kernel exit paths
but the saved PSR value indicates that we are in kernel mode.  This
could occur due to corrupted stack state, which has been observed with
"ftracetest".

This ensures that we catch the problem case before we get to user code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Pull timer updates from Thomas Gleixner:

 - The final conversion of timer wheel timers to timer_setup().

   A few manual conversions and a large coccinelle assisted sweep and
   the removal of the old initialization mechanisms and the related
   code.

 - Remove the now unused VSYSCALL update code

 - Fix permissions of /proc/timer_list. I still need to get rid of that
   file completely

 - Rename a misnomed clocksource function and remove a stale declaration

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
  m68k/macboing: Fix missed timer callback assignment
  treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
  timer: Remove redundant __setup_timer*() macros
  timer: Pass function down to initialization routines
  timer: Remove unused data arguments from macros
  timer: Switch callback prototype to take struct timer_list * argument
  timer: Pass timer_list pointer to callbacks unconditionally
  Coccinelle: Remove setup_timer.cocci
  timer: Remove setup_*timer() interface
  timer: Remove init_timer() interface
  treewide: setup_timer() -> timer_setup() (2 field)
  treewide: setup_timer() -> timer_setup()
  treewide: init_timer() -> setup_timer()
  treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
  s390: cmm: Convert timers to use timer_setup()
  lightnvm: Convert timers to use timer_setup()
  drivers/net: cris: Convert timers to use timer_setup()
  drm/vc4: Convert timers to use timer_setup()
  block/laptop_mode: Convert timers to use timer_setup()
  net/atm/mpc: Avoid open-coded assignment of timer callback function
  ...

Pull ARC updates from Vineet Gupta:

 - more changes for HS48 cores: supporting MMUv5, detecting new
   micro-arch gizmos

 - axs10x platform wiring up reset driver merged in this cycle

 - ARC perf driver optimizations

* tag 'arc-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: perf: avoid vmalloc backed mmap
  ARCv2: perf: optimize given that num counters <= 32
  ARCv2: perf: tweak overflow interrupt
  ARC: [plat-axs10x] DTS: Add reset controller node to manage ethernet reset
  ARCv2: boot log: updates for HS48: dual-issue, ECC, Loop Buffer
  ARCv2: Accomodate HS48 MMUv5 by relaxing MMU ver checking
  ARC: [plat-axs10x] auto-select AXS101 or AXS103 given the  ISA config

Pull more Kbuild updates from Masahiro Yamada:

 - use 'pwd' instead of '/bin/pwd' for portability

 - clean up Makefiles

 - fix ld-option for clang

 - fix malloc'ed data size in Kconfig

 - fix parallel building along with coccicheck

 - fix a minor issue of package building

 - prompt to use "rpm-pkg" instead of "rpm"

 - clean up *.i and *.lst patterns by "make clean"

* tag 'kbuild-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: drop $(extra-y) from real-objs-y
  kbuild: clean up *.i and *.lst patterns by make clean
  kbuild: rpm: prompt to use "rpm-pkg" if "rpm" target is used
  kbuild: pkg: use --transform option to prefix paths in tar
  coccinelle: fix parallel build with CHECK=scripts/coccicheck
  kconfig/symbol.c: use correct pointer type argument for sizeof
  kbuild: Set KBUILD_CFLAGS before incl. arch Makefile
  kbuild: remove all dummy assignments to obj-
  kbuild: create built-in.o automatically if parent directory wants it
  kbuild: /bin/pwd -> pwd

Pull AFS fixes from David Howells:

 - Make AFS file locking work again.

 - Don't write to a page that's being written out, but wait for it to
   complete.

 - Do d_drop() and d_add() in the right places.

 - Put keys on error paths.

 - Remove some redundant code.

* tag 'afs-fixes-20171124' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: remove redundant assignment of dvnode to itself
  afs: cell: Remove unnecessary code in afs_lookup_cell
  afs: Fix signal handling in some file ops
  afs: Fix some dentry handling in dir ops and missing key_puts
  afs: Make afs_write_begin() avoid writing to a page that's being stored
  afs: Fix file locking

Pull KVM updates from Radim Krčmář:
 "Trimmed second batch of KVM changes for Linux 4.15:

   - GICv4 Support for KVM/ARM

   - re-introduce support for CPUs without virtual NMI (cc stable) and
     allow testing of KVM without virtual NMI on available CPUs

   - fix long-standing performance issues with assigned devices on AMD
     (cc stable)"

* tag 'kvm-4.15-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
  kvm: vmx: Allow disabling virtual NMI support
  kvm: vmx: Reinstate support for CPUs without virtual NMI
  KVM: SVM: obey guest PAT
  KVM: arm/arm64: Don't queue VLPIs on INV/INVALL
  KVM: arm/arm64: Fix GICv4 ITS initialization issues
  KVM: arm/arm64: GICv4: Theory of operations
  KVM: arm/arm64: GICv4: Enable VLPI support
  KVM: arm/arm64: GICv4: Prevent userspace from changing doorbell affinity
  KVM: arm/arm64: GICv4: Prevent a VM using GICv4 from being saved
  KVM: arm/arm64: GICv4: Enable virtual cpuif if VLPIs can be delivered
  KVM: arm/arm64: GICv4: Hook vPE scheduling into vgic flush/sync
  KVM: arm/arm64: GICv4: Use the doorbell interrupt as an unblocking source
  KVM: arm/arm64: GICv4: Add doorbell interrupt handling
  KVM: arm/arm64: GICv4: Use pending_last as a scheduling hint
  KVM: arm/arm64: GICv4: Handle INVALL applied to a vPE
  KVM: arm/arm64: GICv4: Propagate property updates to VLPIs
  KVM: arm/arm64: GICv4: Handle MOVALL applied to a vPE
  KVM: arm/arm64: GICv4: Handle CLEAR applied to a VLPI
  KVM: arm/arm64: GICv4: Propagate affinity changes to the physical ITS
  KVM: arm/arm64: GICv4: Unmap VLPI when freeing an LPI
  ...

Pull powerpc fixes from Michael Ellerman:
 "A small batch of fixes, about 50% tagged for stable and the rest for
  recently merged code.

  There's one more fix for the >128T handling on hash. Once a process
  had requested a single mmap above 128T we would then always search
  above 128T. The correct behaviour is to consider the hint address in
  isolation for each mmap request.

  Then a couple of fixes for the IMC PMU, a missing EXPORT_SYMBOL in
  VAS, a fix for STRICT_KERNEL_RWX on 32-bit, and a fix to correctly
  identify P9 DD2.1 but in code that is currently not used by default.

  Thanks to: Aneesh Kumar K.V, Christophe Leroy, Madhavan Srinivasan,
  Sukadev Bhattiprolu"

* tag 'powerpc-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Fix Power9 DD2.1 logic in DT CPU features
  powerpc/perf: Fix IMC_MAX_PMU macro
  powerpc/perf: Fix pmu_count to count only nest imc pmus
  powerpc: Fix boot on BOOK3S_32 with CONFIG_STRICT_KERNEL_RWX
  powerpc/perf/imc: Use cpu_to_node() not topology_physical_package_id()
  powerpc/vas: Export chip_to_vas_id()
  powerpc/64s/slice: Use addr limit when computing slice mask

Pull SCSI target updates from Nicholas Bellinger:

 "This series is predominantly bug-fixes, with a few small improvements
  that have been outstanding over the last release cycle.

  As usual, the associated bug-fixes have CC' tags for stable.

  Also, things have been particularly quiet wrt new developments the
  last months, with most folks continuing to focus on stability atop 4.x
  stable kernels for their respective production configurations.

  Also at this point, the stable trees have been synced up with
  mainline. This will continue to be a priority, as production users
  tend to run exclusively atop stable kernels, a few releases behind
  mainline.

  The highlights include:

   - Fix PR PREEMPT_AND_ABORT null pointer dereference regression in
     v4.11+ (tangwenji)

   - Fix OOPs during removing TCMU device (Xiubo Li + Zhang Zhuoyu)

   - Add netlink command reply supported option for each device (Kenjiro
     Nakayama)

   - cxgbit: Abort the TCP connection in case of data out timeout (Varun
     Prakash)

   - Fix PR/ALUA file path truncation (David Disseldorp)

   - Fix double se_cmd completion during ->cmd_time_out (Mike Christie)

   - Fix QUEUE_FULL + SCSI task attribute handling in 4.1+ (Bryant Ly +
     nab)

   - Fix quiese during transport_write_pending_qf endless loop (nab)

   - Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK in 3.14+
     (Don White + nab)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (35 commits)
  tcmu: Add a missing unlock on an error path
  tcmu: Fix some memory corruption
  iscsi-target: Fix non-immediate TMR reference leak
  iscsi-target: Make TASK_REASSIGN use proper se_cmd->cmd_kref
  target: Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK
  target: Fix quiese during transport_write_pending_qf endless loop
  target: Fix caw_sem leak in transport_generic_request_failure
  target: Fix QUEUE_FULL + SCSI task attribute handling
  iSCSI-target: Use common error handling code in iscsi_decode_text_input()
  target/iscsi: Detect conn_cmd_list corruption early
  target/iscsi: Fix a race condition in iscsit_add_reject_from_cmd()
  target/iscsi: Modify iscsit_do_crypto_hash_buf() prototype
  target/iscsi: Fix endianness in an error message
  target/iscsi: Use min() in iscsit_dump_data_payload() instead of open-coding it
  target/iscsi: Define OFFLOAD_BUF_SIZE once
  target: Inline transport_put_cmd()
  target: Suppress gcc 7 fallthrough warnings
  target: Move a declaration of a global variable into a header file
  tcmu: fix double se_cmd completion
  target: return SAM_STAT_TASK_SET_FULL for TCM_OUT_OF_RESOURCES
  ...

This fixes a missed function prototype callback from the timer conversions.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20171123221902.GA75727@beast