- 26 Apr, 2016 40 commits
-
-
Heiko Carstens authored
commit 84976952 upstream. arch_spin_lock_wait_flags() checks if a spinlock is not held before trying a compare and swap instruction. If the lock is unlocked it tries the compare and swap instruction, however if a different cpu grabbed the lock in the meantime the instruction will fail as expected. Subsequently the arch_spin_lock_wait_flags() incorrectly tries to figure out if the cpu that holds the lock is running. However it is using the wrong cpu number for this (-1) and then will also yield the current cpu to the wrong cpu. Fix this by adding a missing continue statement. Fixes: 470ada6b ("s390/spinlock: refactor arch_spin_lock_wait[_flags]") Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Keerthy authored
commit 56b367c0 upstream. pcs_parse_bits_in_pinctrl_entry uses ffs which gives bit indices ranging from 1 to MAX. This leads to a corner case where we try to request the pin number = MAX and fails. bit_pos value is being calculted using ffs. pin_num_from_lsb uses bit_pos value. pins array is populated with: pin + pin_num_from_lsb. The above is 1 more than usual bit indices as bit_pos uses ffs to compute first set bit. Hence the last of the pins array is populated with the MAX value and not MAX - 1 which causes error when we call pin_request. mask_pos is rightly calculated as ((pcs->fmask) << (bit_pos - 1)) Consequently val_pos and submask are correct. Hence use __ffs which gives (ffs(x) - 1) as the first bit set. fixes: 4e7e8017 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules") Signed-off-by:
Keerthy <j-keerthy@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Alexei Starovoitov authored
commit d82bccc6 upstream. verifier must check for reserved size bits in instruction opcode and reject BPF_LD | BPF_ABS | BPF_DW and BPF_LD | BPF_IND | BPF_DW instructions, otherwise interpreter will WARN_RATELIMIT on them during execution. Fixes: ddd872bc ("bpf: verifier: add checks for BPF_ABS | BPF_IND instructions") Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Lars Persson authored
commit 3dcd493f upstream. A failure in validate_xmit_skb_list() triggered an unconditional call to dev_requeue_skb with skb=NULL. This slowly grows the queue discipline's qlen count until all traffic through the queue stops. We take the optimistic approach and continue running the queue after a failure since it is unknown if later packets also will fail in the validate path. Fixes: 55a93b3e ("qdisc: validate skb without holding lock") Signed-off-by:
Lars Persson <larper@axis.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Mathias Krause authored
commit 309cf37f upstream. Because we miss to wipe the remainder of i->addr[] in packet_mc_add(), pdiag_put_mclist() leaks uninitialized heap bytes via the PACKET_DIAG_MCLIST netlink attribute. Fix this by explicitly memset(0)ing the remaining bytes in i->addr[]. Fixes: eea68e2f ("packet: Report socket mclist info via diag module") Signed-off-by:
Mathias Krause <minipli@googlemail.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Pavel Emelyanov <xemul@parallels.com> Acked-by:
Pavel Emelyanov <xemul@virtuozzo.com> Signed-off-by:
-
Sebastian Ott authored
commit b707c65a upstream. When we refuse a non REQ_TYPE_FS request in the build request function we already hold the queue lock. Thus we must not call blk_end_request_all but __blk_end_request_all. Reported-by:
Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Fixes: de9587a2 ('s390/scm_blk: fix endless loop for requests != REQ_TYPE_FS') Signed-off-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
-
Tony Luck authored
commit ea5dfb5f upstream. Haswell and Broadwell can be configured to hash the channel interleave function using bits [27:12] of the physical address. On those processor models we must check to see if hashing is enabled (bit21 of the HASWELL_HASYSDEFEATURE2 register) and act accordingly. Based on a patch by patrickg <patrickg@supermicro.com> Tested-by:
Patrick Geary <patrickg@supermicro.com> Signed-off-by:
Tony Luck <tony.luck@intel.com> Acked-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Aristeu Rozanski <arozansk@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-edac@vger.kernel.org Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Tony Luck authored
commit ff15e95c upstream. In commit: eb1af3b7 ("Fix computation of channel address") I switched the "sck_way" variable from holding the log2 value read from the h/w to instead be the actual number. Unfortunately it is needed in log2 form when used to shift the address. Tested-by:
-
Jan Beulich authored
commit 103f6112 upstream. Huge pages are not normally available to PV guests. Not suppressing hugetlbfs use results in an endless loop of page faults when user mode code tries to access a hugetlbfs mapped area (since the hypervisor denies such PTEs to be created, but error indications can't be propagated out of xen_set_pte_at(), just like for various of its siblings), and - once killed in an oops like this: kernel BUG at .../fs/hugetlbfs/inode.c:428! invalid opcode: 0000 [#1] SMP ... RIP: e030:[<ffffffff811c333b>] [<ffffffff811c333b>] remove_inode_hugepages+0x25b/0x320 ... Call Trace: [<ffffffff811c3415>] hugetlbfs_evict_inode+0x15/0x40 [<ffffffff81167b3d>] evict+0xbd/0x1b0 [<ffffffff8116514a>] __dentry_kill+0x19a/0x1f0 [<ffffffff81165b0e>] dput+0x1fe/0x220 [<ffffffff81150535>] __fput+0x155/0x200 [<ffffffff81079fc0>] task_work_run+0x60/0xa0 [<ffffffff81063510>] do_exit+0x160/0x400 [<ffffffff810637eb>] do_group_exit+0x3b/0xa0 [<ffffffff8106e8bd>] get_signal+0x1ed/0x470 [<ffffffff8100f854>] do_signal+0x14/0x110 [<ffffffff810030e9>] prepare_exit_to_usermode+0xe9/0xf0 [<ffffffff814178a5>] retint_user+0x8/0x13 This is CVE-2016-3961 / XSA-174. Reported-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
Jan Beulich <jbeulich@suse.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Juergen Gross <JGross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luis R. Rodriguez <mcgrof@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Cc: xen-devel <xen-devel@lists.xenproject.org> Link: http://lkml.kernel.org/r/57188ED802000078000E431C@prv-mh.provo.novell.comSigned-off-by:
-
Dominik Dingel authored
commit 2531c8cf upstream. s390 has a constant hugepage size, by setting HPAGE_SHIFT we also change e.g. the pageblock_order, which should be independent in respect to hugepage support. With this patch every architecture is free to define how to check for hugepage support. Signed-off-by:
Dominik Dingel <dingel@linux.vnet.ibm.com> Acked-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Huacai Chen authored
commit 221004c6 upstream. Signed-off-by:
Huacai Chen <chenhc@lemote.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Jérôme Glisse authored
commit b5dcec69 upstream. Allowing userptr bo which are basicly a list of page from some vma (so either anonymous page or file backed page) would lead to serious corruption of kernel structures and counters (because we overwrite the page->mapping field when mapping buffer). This will already block if the buffer was populated before anyone does try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm vm fault handler. So to be safe just add a check to verify_access() callback. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Jérôme Glisse <jglisse@redhat.com> Signed-off-by:
-
cpaul@redhat.com authored
commit deba0a2a upstream. With the joys of things running concurrently, there's always a chance that the port we get passed in drm_dp_payload_send_msg() isn't actually valid anymore. Because of this, we need to make sure we validate the reference to the port before we use it otherwise we risk running into various race conditions. For instance, on the Dell MST monitor I have here for testing, hotplugging it enough times causes us to kernel panic: [drm:intel_mst_enable_dp] 1 [drm:drm_dp_update_payload_part2] payload 0 1 [drm:intel_get_hpd_pins] hotplug event received, stat 0x00200000, dig 0x10101011, pins 0x00000020 [drm:intel_hpd_irq_handler] digital hpd port B - short [drm:intel_dp_hpd_pulse] got hpd irq on port B - short [drm:intel_dp_check_mst_status] got esi 00 10 00 [drm:drm_dp_update_payload_part2] payload 1 1 general protection fault: 0000 [#1] SMP … Call Trace: [<ffffffffa012b632>] drm_dp_update_payload_part2+0xc2/0x130 [drm_kms_helper] [<ffffffffa032ef08>] intel_mst_enable_dp+0xf8/0x180 [i915] [<ffffffffa0310dbd>] haswell_crtc_enable+0x3ed/0x8c0 [i915] [<ffffffffa030c84d>] intel_atomic_commit+0x5ad/0x1590 [i915] [<ffffffffa01db877>] ? drm_atomic_set_crtc_for_connector+0x57/0xe0 [drm] [<ffffffffa01dc4e7>] drm_atomic_commit+0x37/0x60 [drm] [<ffffffffa0130a3a>] drm_atomic_helper_set_config+0x7a/0xb0 [drm_kms_helper] [<ffffffffa01cc482>] drm_mode_set_config_internal+0x62/0x100 [drm] [<ffffffffa01d02ad>] drm_mode_setcrtc+0x3cd/0x4e0 [drm] [<ffffffffa01c18e3>] drm_ioctl+0x143/0x510 [drm] [<ffffffffa01cfee0>] ? drm_mode_setplane+0x1b0/0x1b0 [drm] [<ffffffff810f79a7>] ? hrtimer_start_range_ns+0x1b7/0x3a0 [<ffffffff81212962>] do_vfs_ioctl+0x92/0x570 [<ffffffff81590852>] ? __sys_recvmsg+0x42/0x80 [<ffffffff81212eb9>] SyS_ioctl+0x79/0x90 [<ffffffff816b4e32>] entry_SYSCALL_64_fastpath+0x1a/0xa4 RIP [<ffffffffa012b026>] drm_dp_payload_send_msg+0x146/0x1f0 [drm_kms_helper] Which occurs because of the hotplug event shown in the log, which ends up causing DRM's dp helpers to drop the port we're updating the payload on and panic. Signed-off-by:
Lyude <cpaul@redhat.com> Reviewed-by:
David Airlie <airlied@linux.ie> Signed-off-by:
-
Takashi Iwai authored
commit 67f3754b upstream. The commit [9bef72bd: ALSA: pcxhr: Use nonatomic PCM ops] converted to non-atomic PCM ops, but shamelessly with an unbalanced mutex locking, which leads to the hangup easily. Fix it. Fixes: 9bef72bd ('ALSA: pcxhr: Use nonatomic PCM ops') Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116441Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Davidlohr Bueso authored
commit fe1bce9e upstream. Otherwise an incoming waker on the dest hash bucket can miss the waiter adding itself to the plist during the lockless check optimization (small window but still the correct way of doing this); similarly to the decrement counterpart. Suggested-by:
Peter Zijlstra <peterz@infradead.org> Signed-off-by:
Davidlohr Bueso <dbueso@suse.de> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: bigeasy@linutronix.de Cc: dvhart@infradead.org Link: http://lkml.kernel.org/r/1461208164-29150-1-git-send-email-dave@stgolabs.netSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 89e9e66b upstream. If userspace calls UNLOCK_PI unconditionally without trying the TID -> 0 transition in user space first then the user space value might not have the waiters bit set. This opens the following race: CPU0 CPU1 uval = get_user(futex) lock(hb) lock(hb) futex |= FUTEX_WAITERS .... unlock(hb) cmpxchg(futex, uval, newval) So the cmpxchg fails and returns -EINVAL to user space, which is wrong because the futex value is valid. To handle this (yes, yet another) corner case gracefully, check for a flag change and retry. [ tglx: Massaged changelog and slightly reworked implementation ] Fixes: ccf9e6a8 ("futex: Make unlock_pi more robust") Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Darren Hart <dvhart@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1460723739-5195-1-git-send-email-bigeasy@linutronix.deSigned-off-by:
-
Alex Deucher authored
commit bcb31eba upstream. bug: https://bugs.freedesktop.org/show_bug.cgi?id=76490Signed-off-by:
-
Anton Blanchard authored
commit 4705e024 upstream. We need to update the user TM feature bits (PPC_FEATURE2_HTM and PPC_FEATURE2_HTM) to mirror what we do with the kernel TM feature bit. At the moment, if firmware reports TM is not available we turn off the kernel TM feature bit but leave the userspace ones on. Userspace thinks it can execute TM instructions and it dies trying. This (together with a QEMU patch) fixes PR KVM, which doesn't currently support TM. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Anton Blanchard authored
commit beff8237 upstream. scan_features() updates cpu_user_features but not cpu_user_features2. Amongst other things, cpu_user_features2 contains the user TM feature bits which we must keep in sync with the kernel TM feature bit. Signed-off-by:
-
Anton Blanchard authored
commit 6997e57d upstream. The REAL_LE feature entry in the ibm_pa_feature struct is missing an MMU feature value, meaning all the remaining elements initialise the wrong values. This means instead of checking for byte 5, bit 0, we check for byte 0, bit 0, and then we incorrectly set the CPU feature bit as well as MMU feature bit 1 and CPU user feature bits 0 and 2 (5). Checking byte 0 bit 0 (IBM numbering), means we're looking at the "Memory Management Unit (MMU)" feature - ie. does the CPU have an MMU. In practice that bit is set on all platforms which have the property. This means we set CPU_FTR_REAL_LE always. In practice that seems not to matter because all the modern cpus which have this property also implement REAL_LE, and we've never needed to disable it. We're also incorrectly setting MMU feature bit 1, which is: #define MMU_FTR_TYPE_8xx 0x00000002 Luckily the only place that looks for MMU_FTR_TYPE_8xx is in Book3E code, which can't run on the same cpus as scan_features(). So this also doesn't matter in practice. Finally in the CPU user feature mask, we're setting bits 0 and 2. Bit 2 is not currently used, and bit 0 is: #define PPC_FEATURE_PPC_LE 0x00000001 Which says the CPU supports the old style "PPC Little Endian" mode. Again this should be harmless in practice as no 64-bit CPUs implement that mode. Fix the code by adding the missing initialisation of the MMU feature. Also add a comment marking CPU user feature bit 2 (0x4) as reserved. It would be unsafe to start using it as old kernels incorrectly set it. Fixes: 44ae3ab3 ("powerpc: Free up some CPU feature bits by moving out MMU-related features") Signed-off-by:
-
Bastien Nocera authored
commit afecb146 upstream. The Optiplex 9020m with Haswell-DT processor needs a quirk for the headset jack at the front of the machine to be able to use microphones. A quirk for this model was originally added in 31278997, but c77900e6 removed it in favour of a more generic version. Unfortunately, pin configurations can changed based on firmware/BIOS versions, and the generic version doesn't have any effect on newer versions of the machine/firmware anymore. With help from David Henningsson <diwic@ubuntu.com> Signed-off-by:
Bastien Nocera <hadess@hadess.net> Tested-by:
-
Linus Walleij authored
commit f36fdacc upstream. The current compile-time check for inversed IENB/CNTL does not work in multiplatform boots: as soon as versatile is included in the build, the IENB/CNTL is switched and breaks graphics. Convert this to a runtime switch. Cc: Rob Herring <robh@kernel.org> Cc: Russell King <linux@arm.linux.org.uk> Fixes: a29da136 ("ARM: versatile: convert to multi-platform") Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Tom Lendacky authored
commit f709b45e upstream. Prevent information from leaking to userspace by doing a memset to 0 of the export state structure before setting the structure values and copying it. This prevents un-initialized padding areas from being copied into the export area. Reported-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Xiaodong Liu authored
commit 0851561d upstream. In sha_complete_job, incorrect mcryptd_hash_request_ctx pointer is used when check and complete other jobs. If the memory of first completed req is freed, while still completing other jobs in the func, kernel will crash since NULL pointer is assigned to RIP. Signed-off-by:
Xiaodong Liu <xiaodong.liu@intel.com> Acked-by:
Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by:
-
Robert Dobrowolski authored
commit e86103a7 upstream. On BXT platform Host Controller and Device Controller figure as same PCI device but with different device function. HCD should not pass data to Device Controller but only to Host Controllers. Checking if companion device is Host Controller, otherwise skip. Signed-off-by:
Robert Dobrowolski <robert.dobrowolski@linux.intel.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Hans de Goede authored
commit 13630746 upstream. Add a new NO_REPORT_LUNS quirk and set it for Seagate drives with an usb-id of: 0bc2:331a, as these will fail to respond to a REPORT_LUNS command. Reported-and-tested-by:
David Webb <djw@noc.ac.uk> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
-
Mathias Nyman authored
commit 98d74f9c upstream. PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will remove the xhci controller from the PCI bus when the last USB device is disconnected. Add a flag to indicate that the host is being removed to avoid queueing configure_endpoint commands for the dropped endpoints. For PCI hotplugged controllers this will prevent 5 second command timeouts For static xhci controllers the configure_endpoint command is not needed in the removal case as everything will be returned, freed, and the controller is reset. For now the flag is only set for PCI connected host controllers. Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Roger Quadros authored
commit ad6b1d91 upstream. The problem seems to be that if a new device is detected while we have already removed the shared HCD, then many of the xhci operations (e.g. xhci_alloc_dev(), xhci_setup_device()) hang as command never completes. I don't think XHCI can operate without the shared HCD as we've already called xhci_halt() in xhci_only_stop_hcd() when shared HCD goes away. We need to prevent new commands from being queued not only when HCD is dying but also when HCD is halted. The following lockup was detected while testing the otg state machine. [ 178.199951] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 178.205799] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 178.214458] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00010010 [ 178.223619] xhci-hcd xhci-hcd.0.auto: irq 400, io mem 0x48890000 [ 178.230677] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 178.237796] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 178.245358] usb usb1: Product: xHCI Host Controller [ 178.250483] usb usb1: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd [ 178.257783] usb usb1: SerialNumber: xhci-hcd.0.auto [ 178.267014] hub 1-0:1.0: USB hub found [ 178.272108] hub 1-0:1.0: 1 port detected [ 178.278371] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 178.284171] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 178.294038] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 178.301183] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 178.308776] usb usb2: Product: xHCI Host Controller [ 178.313902] usb usb2: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd [ 178.321222] usb usb2: SerialNumber: xhci-hcd.0.auto [ 178.329061] hub 2-0:1.0: USB hub found [ 178.333126] hub 2-0:1.0: 1 port detected [ 178.567585] dwc3 48890000.usb: usb_otg_start_host 0 [ 178.572707] xhci-hcd xhci-hcd.0.auto: remove, state 4 [ 178.578064] usb usb2: USB disconnect, device number 1 [ 178.586565] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 178.592585] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 178.597924] usb usb1: USB disconnect, device number 1 [ 178.603248] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 190.597337] INFO: task kworker/u4:0:6 blocked for more than 10 seconds. [ 190.604273] Not tainted 4.0.0-rc1-00024-g6111320 #1058 [ 190.610228] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 190.618443] kworker/u4:0 D c05c0ac0 0 6 2 0x00000000 [ 190.625120] Workqueue: usb_otg usb_otg_work [ 190.629533] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98) [ 190.636915] [<c05c10ac>] (schedule) from [<c05c1318>] (schedule_preempt_disabled+0xc/0x10) [ 190.645591] [<c05c1318>] (schedule_preempt_disabled) from [<c05c23d0>] (mutex_lock_nested+0x1ac/0x3fc) [ 190.655353] [<c05c23d0>] (mutex_lock_nested) from [<c046cf8c>] (usb_disconnect+0x3c/0x208) [ 190.664043] [<c046cf8c>] (usb_disconnect) from [<c0470cf0>] (_usb_remove_hcd+0x98/0x1d8) [ 190.672535] [<c0470cf0>] (_usb_remove_hcd) from [<c0485da8>] (usb_otg_start_host+0x50/0xf4) [ 190.681299] [<c0485da8>] (usb_otg_start_host) from [<c04849a4>] (otg_set_protocol+0x5c/0xd0) [ 190.690153] [<c04849a4>] (otg_set_protocol) from [<c0484b88>] (otg_set_state+0x170/0xbfc) [ 190.698735] [<c0484b88>] (otg_set_state) from [<c0485740>] (otg_statemachine+0x12c/0x470) [ 190.707326] [<c0485740>] (otg_statemachine) from [<c0053c84>] (process_one_work+0x1b4/0x4a0) [ 190.716162] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c) [ 190.724742] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0) [ 190.732328] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24) [ 190.739898] 5 locks held by kworker/u4:0/6: [ 190.744274] #0: ("%s""usb_otg"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0 [ 190.752799] #1: ((&otgd->work)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0 [ 190.761326] #2: (&otgd->fsm.lock){+.+.+.}, at: [<c048562c>] otg_statemachine+0x18/0x470 [ 190.769934] #3: (usb_bus_list_lock){+.+.+.}, at: [<c0470ce8>] _usb_remove_hcd+0x90/0x1d8 [ 190.778635] #4: (&dev->mutex){......}, at: [<c046cf8c>] usb_disconnect+0x3c/0x208 [ 190.786700] INFO: task kworker/1:0:14 blocked for more than 10 seconds. [ 190.793633] Not tainted 4.0.0-rc1-00024-g6111320 #1058 [ 190.799567] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 190.807783] kworker/1:0 D c05c0ac0 0 14 2 0x00000000 [ 190.814457] Workqueue: usb_hub_wq hub_event [ 190.818866] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98) [ 190.826252] [<c05c10ac>] (schedule) from [<c05c4e40>] (schedule_timeout+0x13c/0x1ec) [ 190.834377] [<c05c4e40>] (schedule_timeout) from [<c05c19f0>] (wait_for_common+0xbc/0x150) [ 190.843062] [<c05c19f0>] (wait_for_common) from [<bf068a3c>] (xhci_setup_device+0x164/0x5cc [xhci_hcd]) [ 190.852986] [<bf068a3c>] (xhci_setup_device [xhci_hcd]) from [<c046b7f4>] (hub_port_init+0x3f4/0xb10) [ 190.862667] [<c046b7f4>] (hub_port_init) from [<c046eb64>] (hub_event+0x704/0x1018) [ 190.870704] [<c046eb64>] (hub_event) from [<c0053c84>] (process_one_work+0x1b4/0x4a0) [ 190.878919] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c) [ 190.887503] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0) [ 190.895076] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24) [ 190.902650] 5 locks held by kworker/1:0/14: [ 190.907023] #0: ("usb_hub_wq"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0 [ 190.915454] #1: ((&hub->events)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0 [ 190.924070] #2: (&dev->mutex){......}, at: [<c046e490>] hub_event+0x30/0x1018 [ 190.931768] #3: (&port_dev->status_lock){+.+.+.}, at: [<c046eb50>] hub_event+0x6f0/0x1018 [ 190.940558] #4: (&bus->usb_address0_mutex){+.+.+.}, at: [<c046b458>] hub_port_init+0x58/0xb10 Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
-
Lu Baolu authored
commit 71504062 upstream. This patch fixes some wild pointers produced by xhci_mem_cleanup. These wild pointers will cause system crash if xhci_mem_cleanup() is called twice. Reported-and-tested-by:
Pengcheng Li <lpc.li@hisilicon.com> Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by:
-
Yoshihiro Shimoda authored
commit 0a380be8 upstream. On some xHCI controllers (e.g. R-Car SoCs), the AC64 bit (bit 0) of HCCPARAMS1 is set to 1. However, the xHCs don't support 64-bit address memory pointers actually. So, in this case, this driver should call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in xhci_gen_setup(). Otherwise, the xHCI controller will be died after a usb device is connected if it runs on above 4GB physical memory environment. So, this patch adds a new quirk XHCI_NO_64BIT_SUPPORT to resolve such an issue. Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Mathias Nyman authored
commit 671ffdff upstream. Give USB3 devices a better chance to enumerate at USB 3 speeds if they are connected to a suspended host. Solves an issue with NEC uPD720200 host hanging when partially enumerating a USB3 device as USB2 after host controller runtime resume. Tested-by:
Mike Murdoch <main.haarp@gmail.com> Signed-off-by:
-
Rafal Redzimski authored
commit 0d46faca upstream. Broxton B0 also requires XHCI_PME_STUCK_QUIRK. Adding PCI device ID for Broxton B and adding to quirk. Signed-off-by:
Rafal Redzimski <rafal.f.redzimski@intel.com> Signed-off-by:
-
Rui Salvaterra authored
commit 3e26a691 upstream. Based on Sergey's test patch [1], this fixes zram with lz4 compression on big endian cpus. Note that the 64-bit preprocessor test is not a cleanup, it's part of the fix, since those identifiers are bogus (for example, __ppc64__ isn't defined anywhere else in the kernel, which means we'd fall into the 32-bit definitions on ppc64). Tested on ppc64 with no regression on x86_64. [1] http://marc.info/?l=linux-kernel&m=145994470805853&w=4Suggested-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by:
Rui Salvaterra <rsalvaterra@gmail.com> Reviewed-by:
-
Andy Shevchenko authored
commit 3fe6409c upstream. The commit 89500520 ("dmaengine: dw: apply both HS interfaces and remove slave_id usage") cleaned up the code to avoid usage of depricated slave_id member of generic slave configuration. Meanwhile it broke the master selection by removing important call to dwc_set_masters() in ->device_alloc_chan_resources() which copied masters from custom slave configuration to the internal channel structure. Everything works until now since there is no customized connection of DesignWare DMA IP to the bus, i.e. one bus and one or more masters are in use. The configurations where 2 masters are connected to the different masters are not working anymore. We are expecting one user of such configuration and need to select masters properly. Besides that it is obviously a performance regression since only one master is in use in multi-master configuration. Select masters in accordance with what user asked for. Keep this patch in a form more suitable for back porting. We are safe to take necessary data in ->device_alloc_chan_resources() because we don't support generic slave configuration embedded into custom one, and thus the only way to provide such is to use the parameter to a filter function which is called exactly before channel resource allocation. While here, replase BUG_ON to less noisy dev_warn() and prevent channel allocation in case of error. Fixes: 89500520 ("dmaengine: dw: apply both HS interfaces and remove slave_id usage") Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Hyungwon Hwang authored
commit 023d8218 upstream. The commit [bd481285: ALSA: hda - Fix forgotten HDMI monitor_present update] covered the missing update of monitor_present flag, but this caused a regression for devices without the i915 eld notifier. Since the old code supposed that pin_eld->monitor_present was updated by the caller side, the hdmi_present_sense_via_verbs() doesn't update the temporary eld->monitor_present but only pin_eld->monitor_present, which is now overridden in update_eld(). The fix is to update pin_eld->monitor_present as well before calling update_eld(). Note that this may still leave monitor_present flag in an inconsistent state when the driver repolls, but this is at least the old behavior. More proper fix will follow in the later patch. Fixes: bd481285 ('ALSA: hda - Fix forgotten HDMI monitor_present update') Signed-off-by:
Hyungwon Hwang <hyungwon.hwang7@gmail.com> Signed-off-by:
-
Dmitry Ivanov authored
commit 8f815cdd upstream. A non-privileged user can create a netlink socket with the same port_id as used by an existing open nl80211 netlink socket (e.g. as used by a hostapd process) with a different protocol number. Closing this socket will then lead to the notification going to nl80211's socket release notification handler, and possibly cause an action such as removing a virtual interface. Fix this issue by checking that the netlink protocol is NETLINK_GENERIC. Since generic netlink has no notifier chain of its own, we can't fix the problem more generically. Fixes: 026331c4 ("cfg80211/mac80211: allow registering for and sending action frames") Signed-off-by:
Dmitry Ivanov <dima@ubnt.com> [rewrite commit message] Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Kailang Yang authored
commit adcdd0d5 upstream. This is Dell usb dock audio workaround. It was fixed the master volume keep lower. [Some background: the patch essentially skips the controls of a couple of FU volumes. Although the firmware exposes the dB and the value information via the usb descriptor, changing the values (we set the min volume as default) screws up the device. Although this has been fixed in the newer firmware, the devices are shipped with the old firmware, thus we need the workaround in the driver side. -- tiwai] Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
-
Jerome Marchand authored
commit 8d4a2ec1 upstream. Changes since V1: fixed the description and added KASan warning. In assoc_array_insert_into_terminal_node(), we call the compare_object() method on all non-empty slots, even when they're not leaves, passing a pointer to an unexpected structure to compare_object(). Currently it causes an out-of-bound read access in keyring_compare_object detected by KASan (see below). The issue is easily reproduced with keyutils testsuite. Only call compare_object() when the slot is a leave. KASan warning: ================================================================== BUG: KASAN: slab-out-of-bounds in keyring_compare_object+0x213/0x240 at addr ffff880060a6f838 Read of size 8 by task keyctl/1655 ============================================================================= BUG kmalloc-192 (Not tainted): kasan: bad access detected ----------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: Allocated in assoc_array_insert+0xfd0/0x3a60 age=69 cpu=1 pid=1647 ___slab_alloc+0x563/0x5c0 __slab_alloc+0x51/0x90 kmem_cache_alloc_trace+0x263/0x300 assoc_array_insert+0xfd0/0x3a60 __key_link_begin+0xfc/0x270 key_create_or_update+0x459/0xaf0 SyS_add_key+0x1ba/0x350 entry_SYSCALL_64_fastpath+0x12/0x76 INFO: Slab 0xffffea0001829b80 objects=16 used=8 fp=0xffff880060a6f550 flags=0x3fff8000004080 INFO: Object 0xffff880060a6f740 @offset=5952 fp=0xffff880060a6e5d1 Bytes b4 ffff880060a6f730: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f740: d1 e5 a6 60 00 88 ff ff 0e 00 00 00 00 00 00 00 ...`............ Object ffff880060a6f750: 02 cf 8e 60 00 88 ff ff 02 c0 8e 60 00 88 ff ff ...`.......`.... Object ffff880060a6f760: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f770: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f780: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f790: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7d0: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff880060a6f7f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ CPU: 0 PID: 1655 Comm: keyctl Tainted: G B 4.5.0-rc4-kasan+ #291 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 0000000000000000 000000001b2800b4 ffff880060a179e0 ffffffff81b60491 ffff88006c802900 ffff880060a6f740 ffff880060a17a10 ffffffff815e2969 ffff88006c802900 ffffea0001829b80 ffff880060a6f740 ffff880060a6e650 Call Trace: [<ffffffff81b60491>] dump_stack+0x85/0xc4 [<ffffffff815e2969>] print_trailer+0xf9/0x150 [<ffffffff815e9454>] object_err+0x34/0x40 [<ffffffff815ebe50>] kasan_report_error+0x230/0x550 [<ffffffff819949be>] ? keyring_get_key_chunk+0x13e/0x210 [<ffffffff815ec62d>] __asan_report_load_n_noabort+0x5d/0x70 [<ffffffff81994cc3>] ? keyring_compare_object+0x213/0x240 [<ffffffff81994cc3>] keyring_compare_object+0x213/0x240 [<ffffffff81bc238c>] assoc_array_insert+0x86c/0x3a60 [<ffffffff81bc1b20>] ? assoc_array_cancel_edit+0x70/0x70 [<ffffffff8199797d>] ? __key_link_begin+0x20d/0x270 [<ffffffff8199786c>] __key_link_begin+0xfc/0x270 [<ffffffff81993389>] key_create_or_update+0x459/0xaf0 [<ffffffff8128ce0d>] ? trace_hardirqs_on+0xd/0x10 [<ffffffff81992f30>] ? key_type_lookup+0xc0/0xc0 [<ffffffff8199e19d>] ? lookup_user_key+0x13d/0xcd0 [<ffffffff81534763>] ? memdup_user+0x53/0x80 [<ffffffff819983ea>] SyS_add_key+0x1ba/0x350 [<ffffffff81998230>] ? key_get_type_from_user.constprop.6+0xa0/0xa0 [<ffffffff828bcf4e>] ? retint_user+0x18/0x23 [<ffffffff8128cc7e>] ? trace_hardirqs_on_caller+0x3fe/0x580 [<ffffffff81004017>] ? trace_hardirqs_on_thunk+0x17/0x19 [<ffffffff828bc432>] entry_SYSCALL_64_fastpath+0x12/0x76 Memory state around the buggy address: ffff880060a6f700: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00 ffff880060a6f780: 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc >ffff880060a6f800: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff880060a6f880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff880060a6f900: fc fc fc fc fc fc 00 00 00 00 00 00 00 00 00 00 ================================================================== Signed-off-by:
Jerome Marchand <jmarchan@redhat.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Vladis Dronov authored
commit 162f98de upstream. The gtco driver expects at least one valid endpoint. If given malicious descriptors that specify 0 for the number of endpoints, it will crash in the probe function. Ensure there is at least one endpoint on the interface before using it. Also let's fix a minor coding style issue. The full correct report of this issue can be found in the public Red Hat Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1283385Reported-by:
Ralf Spenneberg <ralf@spenneberg.net> Signed-off-by:
Vladis Dronov <vdronov@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
John Keeping authored
commit d59a1f71 upstream. The SPICE protocol considers the position of a cursor to be the location of its active pixel on the display, so the cursor is drawn with its top-left corner at "(x - hot_spot_x, y - hot_spot_y)" but the DRM cursor position gives the location where the top-left corner should be drawn, with the hotspot being a hint for drivers that need it. This fixes the location of the window resize cursors when using Fluxbox with the QXL DRM driver and both the QXL and modesetting X drivers. Signed-off-by:
John Keeping <john@metanate.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1447845445-2116-1-git-send-email-john@metanate.comSigned-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
