PioD controller was not described in the device tree since we don't use
it. As pinctrl-at91 allows disabled gpio controllers in the device
tree, we can add it to complete the device description.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

There is an external resistor divider on PB16, acting like a pull-down,
the pull-up increase power consumption and prevent the vbus detect pin
to reach Vss voltage, ~1.5V mesured on my board, it might not even work
if the pull-up is stronger than usual.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

According to v4l2 dt document, we add:
  a camera host: ISI port.
  a i2c camera sensor: ov2640 port.
to sama5d3xmb.dtsi.

The ov2640 node defines the pinctrls, clocks and refer to isi port.
The ISI node also has a reference to the ov2640 port.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

For sama5d3xmb board, the pins: pinctrl_isi_pck_as_mck is pck1, and
used to provide MCK for camera sensor.

We change its name to: pinctrl_pck1_as_isi_mck.

As we want camera sensor instead of ISI to configure the pck1 (ISI_MCK) pin.
So we remove this pinctrl from ISI DT node. It will be added in sensor's
DT node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

For sama5d3xmb board, the pins: pinctrl_isi_{power,reset} is used to
power-down or reset camera sensor.
So we should let camera sensor instead of ISI to configure the pins.

This patch will change pinctrl name from pinctrl_isi_{power,reset} to
pinctrl_sensor_{power,reset}. And remove these two pinctrl from ISI's
DT node. We will add these two pinctrl to sensor's DT node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The mck is decided by the board design, move it to mb related
dtsi file.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The ISI has 12 data lines, add the missing two data lines.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

As the ISI has 12 data lines, however we only use 8 data lines with
sensor module. So, split the data line into two groups which make
it can be choosed depends on the hardware design.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add ISI peripheral clock in sama5d3.dtsi.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The ethernut5 is actually based on an at91sam9xe, use the correct dts include.

Cc: Martin Reimann <martin.reimann@egnite.de>
Cc: Tim Schendekehl <tim.schendekehl@egnite.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

at91sam9xe is slightly different from at91sam9260, in particular it has a
different SRAM size and location.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add nodes for the SRAM available on atmel SoCs
For the at91sam9260 and the at91sam9g20, address mirroring is used to create a
single contiguous SRAM range instead of declaring two separate banks.

Also remove leftover TODOs in the sam9g45 file
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: correct at91sam9rl sram size => 0x10000]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable the RTC on the at91rm9200ek.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add a node for the RTC available on at91rm9200.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add node for the RTC available on the at91sam9n12.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The sama4d4 has Special Function Registers that allow to manage DDR, OHCI, EBI
and AIC interrupt redirection.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: reg size: 0x60]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The sama5d3 has Special Function Registers that allow to manage OHCI, EBI and
the UTMI clock.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: reg size: 0x60]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The special function registers gather some registers that allow to tweak
features provided by IPs controlled through another register range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: reg size: 0x60]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

That clock should be called ac97_clk.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This D2 led is available for all sama5d3x-ek board. So make it a
heartbeat LED.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Pull ARM fixes from Russell King:
 "Three small fixes from over the Christmas period, and wiring up the
  new execveat syscall for ARM"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error
  ARM: 8253/1: mm: use phys_addr_t type in map_lowmem() for kernel mem region
  ARM: 8249/1: mm: dump: don't skip regions
  ARM: wire up execveat syscall

Pull x86 fixes from Ingo Molnar:
 "Misc fixes: two vdso fixes, two kbuild fixes and a boot failure fix
  with certain odd memory mappings"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, vdso: Use asm volatile in __getcpu
  x86/build: Clean auto-generated processor feature files
  x86: Fix mkcapflags.sh bash-ism
  x86: Fix step size adjustment during initial memory mapping
  x86_64, vdso: Fix the vdso address randomization algorithm

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes: group scheduling corner case fix, two deadline scheduler
  fixes, effective_load() overflow fix, nested sleep fix, 6144 CPUs
  system fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix RCU stall upon -ENOMEM in sched_create_group()
  sched/deadline: Avoid double-accounting in case of missed deadlines
  sched/deadline: Fix migration of SCHED_DEADLINE tasks
  sched: Fix odd values in effective_load() calculations
  sched, fanotify: Deal with nested sleeps
  sched: Fix KMALLOC_MAX_SIZE overflow during cpumask allocation

Pull perf fixes from Ingo Molnar:
 "Mostly tooling fixes, but also some kernel side fixes: uncore PMU
  driver fix, user regs sampling fix and an instruction decoder fix that
  unbreaks PEBS precise sampling"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/uncore/hsw-ep: Handle systems with only two SBOXes
  perf/x86_64: Improve user regs sampling
  perf: Move task_pt_regs sampling into arch code
  x86: Fix off-by-one in instruction decoder
  perf hists browser: Fix segfault when showing callchain
  perf callchain: Free callchains when hist entries are deleted
  perf hists: Fix children sort key behavior
  perf diff: Fix to sort by baseline field by default
  perf list: Fix --raw-dump option
  perf probe: Fix crash in dwarf_getcfi_elf
  perf probe: Fix to fall back to find probe point in symbols
  perf callchain: Append callchains only when requested
  perf ui/tui: Print backtrace symbols when segfault occurs
  perf report: Show progress bar for output resorting

Pull locking fixes from Ingo Molnar:
 "A liblockdep fix and a mutex_unlock() mutex-debugging fix"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  mutex: Always clear owner field upon mutex_unlock()
  tools/liblockdep: Fix debug_check thinko in mutex destroy

Fix for BUG_ON(anon_vma->degree) splashes in unlink_anon_vmas() ("kernel
BUG at mm/rmap.c:399!") caused by commit 7a3ef208 ("mm: prevent
endless growth of anon_vma hierarchy")

Anon_vma_clone() is usually called for a copy of source vma in
destination argument.  If source vma has anon_vma it should be already
in dst->anon_vma.  NULL in dst->anon_vma is used as a sign that it's
called from anon_vma_fork().  In this case anon_vma_clone() finds
anon_vma for reusing.

Vma_adjust() calls it differently and this breaks anon_vma reusing
logic: anon_vma_clone() links vma to old anon_vma and updates degree
counters but vma_adjust() overrides vma->anon_vma right after that.  As
a result final unlink_anon_vmas() decrements degree for wrong anon_vma.

This patch assigns ->anon_vma before calling anon_vma_clone().
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-and-tested-by: Chris Clayton <chris2553@googlemail.com>
Reported-and-tested-by: Oded Gabbay <oded.gabbay@amd.com>
Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Daniel Forrest <dan.forrest@ssec.wisc.edu>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: stable@vger.kernel.org  # to match back-porting of 7a3ef208Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit fee7e49d ("mm: propagate error from stack expansion even for
guard page") made sure that we return the error properly for stack
growth conditions.  It also theorized that counting the guard page
towards the stack limit might break something, but also said "Let's see
if anybody notices".

Somebody did notice.  Apparently android-x86 sets the stack limit very
close to the limit indeed, and including the guard page in the rlimit
check causes the android 'zygote' process problems.

So this adds the (fairly trivial) code to make the stack rlimit check be
against the actual real stack size, rather than the size of the vma that
includes the guard page.
Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org>
Cc: Jay Foad <jay.foad@gmail.com>
Cc: stable@kernel.org  # to match back-porting of fee7e49dSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull VFIO fix from Alex Williamson:
 "Fix PCI header check in vfio_pci_probe() (Wei Yang)"

* tag 'vfio-v3.19-rc4' of git://github.com/awilliam/linux-vfio:
  vfio-pci: Fix the check on pci device type in vfio_pci_probe()

Pull SCSI fix from James Bottomley:
 "Just one fix: a qlogic busy wait regression"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  qla2xxx: fix busy wait regression

Pull sound fixes from Takashi Iwai:
 "All a few small regression or stable fixes: a Nvidia HDMI ID addition,
  a regression fix for CAIAQ stream count, a typo fix for GPIO setup
  with STAC/IDT HD-audio codecs, and a Fireworks big-endian fix"

* tag 'sound-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: fireworks: fix an endianness bug for transaction length
  ALSA: hda - Add new GPU codec ID 0x10de0072 to snd-hda
  ALSA: hda - Fix wrong gpio_dir & gpio_mask hint setups for IDT/STAC codecs
  ALSA: snd-usb-caiaq: fix stream count check

Pull HID updates from Jiri Kosina:

 - bounds checking fixes in logitech and roccat drivers, from Peter Wu
   and Dan Carpenter

 - double-kfree fix in i2c-hid driver on bus shutdown, from Mika
   Westerberg

 - a couple of various small driver fixes

 - a few device id additions

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: roccat: potential out of bounds in pyra_sysfs_write_settings()
  HID: Add a new id 0x501a for Genius MousePen i608X
  HID: logitech-hidpp: prefix the name with "Logitech"
  HID: logitech-hidpp: avoid unintended fall-through
  HID: Allow HID_BATTERY_STRENGTH to be enabled
  HID: i2c-hid: Do not free buffers in i2c_hid_stop()
  HID: add battery quirk for USB_DEVICE_ID_APPLE_ALU_WIRELESS_2011_ISO keyboard
  HID: logitech-hidpp: check WTP report length
  HID: logitech-dj: check report length

Pull drm fixes from Dave Airlie:
 "I'm briefly working between holidays and LCA, so this is close to a
  couple of weeks of fixes,

  Two sets of amdkfd fixes, this is a new feature this kernel, and this
  pull fixes a few issues since it got merged, ordering when built-in to
  kernel and also the iommu vs gpu ordering patch, it also reworks the
  ioctl before the initial release.

  Otherwise:
   - radeon: some misc fixes all over, hdmi, 4k, dpm
   - nouveau: mcp77 init fixes, oops fix, bug on fix, msi fix
   - i915: power fixes, revert VGACNTR patch

  Probably be quiteer next week since I'll be at LCA anyways"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
  drm/amdkfd: rewrite kfd_ioctl() according to drm_ioctl()
  drm/amdkfd: reformat IOCTL definitions to drm-style
  drm/amdkfd: Do copy_to/from_user in general kfd_ioctl()
  drm/radeon: integer underflow in radeon_cp_dispatch_texture()
  drm/radeon: adjust default bapm settings for KV
  drm/radeon: properly filter DP1.2 4k modes on non-DP1.2 hw
  drm/radeon: fix sad_count check for dce3
  drm/radeon: KV has three PPLLs (v2)
  drm/amdkfd: unmap VMID<-->PASID when relesing VMID (non-HWS)
  drm/radeon: Init amdkfd only if it was compiled
  amdkfd: actually allocate longs for the pasid bitmask
  drm/nouveau/nouveau: Do not BUG_ON(!spin_is_locked()) on UP
  drm/nv4c/mc: disable msi
  drm/nouveau/fb/ram/mcp77: enable NISO poller
  drm/nouveau/fb/ram/mcp77: use carveout reg to determine size
  drm/nouveau/fb/ram/mcp77: subclass nouveau_ram
  drm/nouveau: wake up the card if necessary during gem callbacks
  drm/nouveau/device: Add support for GK208B, resolves bug 86935
  drm/nouveau: fix missing return statement in nouveau_ttm_tt_unpopulate
  drm/nouveau/bios: fix oops on pre-nv50 chipsets
  ...

Pull arm64 fixes from Will Deacon:
 "Here is a handful of minor arm64 fixes discovered and fixed over the
  Christmas break.  The main part is adding some missing #includes that
  we seem to be getting transitively but have started causing problems
  in -next.

   - Fix early mapping fixmap corruption by EFI runtime services
   - Fix __NR_compat_syscalls off-by-one
   - Add missing sanity checks for some 32-bit registers
   - Add some missing #includes which we get transitively
   - Remove unused prepare_to_copy() macro"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64/efi: add missing call to early_ioremap_reset()
  arm64: fix missing asm/io.h include in kernel/smp_spin_table.c
  arm64: fix missing asm/alternative.h include in kernel/module.c
  arm64: fix missing linux/bug.h include in asm/arch_timer.h
  arm64: fix missing asm/pgtable-hwdef.h include in asm/processor.h
  arm64: sanity checks: add missing AArch32 registers
  arm64: Remove unused prepare_to_copy()
  arm64: Correct __NR_compat_syscalls for bpf

Pull kgdb/kdb fixes from Jason Wessel:
 "These have been around since 3.17 and in kgdb-next for the last 9
  weeks and some will go back to -stable.

  Summary of changes:

  Cleanups
   - kdb: Remove unused command flags, repeat flags and KDB_REPEAT_NONE

  Fixes
   - kgdb/kdb: Allow access on a single core, if a CPU round up is
     deemed impossible, which will allow inspection of the now "trashed"
     kernel
   - kdb: Add enable mask for the command groups
   - kdb: access controls to restrict sensitive commands"

* tag 'for_linus-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
  kernel/debug/debug_core.c: Logging clean-up
  kgdb: timeout if secondary CPUs ignore the roundup
  kdb: Allow access to sensitive commands to be restricted by default
  kdb: Add enable mask for groups of commands
  kdb: Categorize kdb commands (similar to SysRq categorization)
  kdb: Remove KDB_REPEAT_NONE flag
  kdb: Use KDB_REPEAT_* values as flags
  kdb: Rename kdb_register_repeat() to kdb_register_flags()
  kdb: Rename kdb_repeat_t to kdb_cmdflags_t, cmd_repeat to cmd_flags
  kdb: Remove currently unused kdbtab_t->cmd_flags

Pull two nfsd bugfixes from Bruce Fields.

* 'for-3.19' of git://linux-nfs.org/~bfields/linux:
  rpc: fix xdr_truncate_encode to handle buffer ending on page boundary
  nfsd: fix fi_delegees leak when fi_had_conflict returns true

Pull two Ceph fixes from Sage Weil:
 "These are both pretty trivial: a sparse warning fix and size_t printk
  thing"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: fix sparse endianness warnings
  ceph: use %zu for len in ceph_fill_inline_data()

Pull btrfs fixes from Chris Mason:
 "None of these are huge, but my commit does fix a regression from 3.18
  that could cause lost files during log replay.

  This also adds Dave Sterba to the list of Btrfs maintainers.  It
  doesn't mean we're doing things differently, but Dave has really been
  helping with the maintainer workload for years"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: don't delay inode ref updates during log replay
  Btrfs: correctly get tree level in tree_backref_for_extent
  Btrfs: call inode_dec_link_count() on mkdir error path
  Btrfs: abort transaction if we don't find the block group
  Btrfs, scrub: uninitialized variable in scrub_extent_for_parity()
  Btrfs: add more maintainers

Merge misc fixes from Andrew Morton:
 "12 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm, vmscan: prevent kswapd livelock due to pfmemalloc-throttled process being killed
  memcg: fix destination cgroup leak on task charges migration
  mm: memcontrol: switch soft limit default back to infinity
  mm/debug_pagealloc: remove obsolete Kconfig options
  vfs: renumber FMODE_NONOTIFY and add to uniqueness check
  arch/blackfin/mach-bf533/boards/stamp.c: add linux/delay.h
  ocfs2: fix the wrong directory passed to ocfs2_lookup_ino_from_name() when link file
  MAINTAINERS: update rydberg's addresses
  mm: protect set_page_dirty() from ongoing truncation
  mm: prevent endless growth of anon_vma hierarchy
  exit: fix race between wait_consider_task() and wait_task_zombie()
  ocfs2: remove bogus check in dlm_process_recovery_data