- 12 Mar, 2011 21 commits
-
-
John Fastabend authored
The PFC configuration is not cleared until the device is reset. This has not been a problem because setting DCB attributes forced a hardware reset. Now that we no longer require this reset to occur PFC remains configured even after being disabled until the device is reset. This removes a goto in the PFC hardware set routines for 82598 and 82599 devices that was short circuiting the clear. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Lior Levy authored
Implemented ixgbe_ndo_set_vf_bw function which is being used by iproute2 tool. In addition, updated ixgbe_ndo_get_vf_config function to show the actual rate limit to the user. The rate limitation can be configured only when the link is up and the link speed is 10Gb. The rate limit value can be 0 or ranged between 11 and actual link speed measured in Mbps. A value of '0' disables the rate limit for this specific VF. iproute2 usage will be 'ip link set ethX vf Y rate Z'. After the command is made, the rate will be changed instantly. To view the current rate limit, use 'ip link show ethX'. The rates will be zeroed only upon driver reload or a link speed change. This feature is being supported by 82599 and X540 devices. Signed-off-by: Lior Levy <lior.levy@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
John Fastabend authored
DCB provides a guaranteed bandwidth in the case with 0% bandwidth then no bandwidth is guaranteed. However the traffic class should still be able to transmit traffic. For this to work the traffic class must be given the minimum credits required to send a frame. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
VF Free Running Timer register name missing an F. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Evan Swanson <evan.swanson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
This change updates the PHY setup code to support 100Mbps capable PHYs as well as 10G and 1Gbps. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
The VF mailbox polling for acks and messages would reset the timer to zero on a timeout. Under heavy load a timeout may actually occur without being the result of an error and when this occurs it is not practical to perform a full VF driver reset on every message timeout. Instead, just return an error (which is already done) and the VF driver will have an opportunity to retry the operation. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
John Fastabend authored
DCB settings are cleared in the hardware across link events during ifup ixgbe reprograms the hardware for DCB if it is enabled. Now that we have two modes CEE or IEEE we need to use the correct set of configuration data. This patch checks the dcbx_cap bits and then enables the device in the correct mode. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
John Fastabend authored
This patch adds support to use the priority assignment table in the ieee_ets structure to map priorities to traffic classes. Previously ixgbe only supported a 1:1 mapping. Now we can enable and disable hardware DCB support when multiple traffic classes are actually being used. This allows the default case all priorities mapped to traffic class 0 to work in normal hardware mode and utilize the full packet buffer. This patch does not address putting the hardware in 4TC mode so packet buffer space may be underutilized in this case. A follow up patch can address this optimization. But at least we have the hooks to do this now. Also CEE will behave as it always has and map priorities 1:1 with traffic classes. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
John Fastabend authored
The patch below allowed IEEE 802.1Qaz and CEE DCB hardware configurations to use common hardware set routines, commit 88eb696cc6a7af8f9272266965b1a4dd7d6a931b Author: John Fastabend <john.r.fastabend@intel.com> Date: Thu Feb 10 03:02:11 2011 -0800 ixgbe: DCB, abstract out dcb_config from DCB hardware configuration However the case when CEE link strict and group strict are set was missed and are currently being mapped incorrectly in some configurations. This patch resolves this. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
John Fastabend authored
RSS had previously been disabled when DCB was enabled because DCB was single queued per traffic class. Now that DCB implements multiple Tx/Rx rings per traffic class enable RSS. Here RSS hashes across the queues in the traffic class. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain.@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
John Fastabend authored
This patch adds the ndo_tc_setup to ixgbe. By default we set the device to use strict priority. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain.@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
John Fastabend authored
This enables multiple {Tx|Rx} rings per traffic class while in DCB mode. In order to get this working as expected the tc_to_tx net device mapping is configured as well as the prio_tc_map. skb priorities are mapped across a range of queue pairs to get a distribution per traffic class. The maximum number of queue pairs used while in DCB mode is capped at 64. The hardware max is actually 128 queues but 64 is sufficient for now and allocating more seemed a bit excessive. It is easy enough to increase the cap later if need be. To get the 802.1Q priority tags inserted correctly ixgbe was previously using the skb queue_mapping field to directly set the 802.1Q priority. This no longer works because we have removed the 1:1 mapping between queues and traffic class. Each ring is aligned with an 802.1Qaz traffic class so here we add an extra field to the ring struct to identify the 802.1Q traffic class. This uses an extra byte of the ixgbe_ring struct fortunately there was a 2byte hole, struct ixgbe_ring { void * desc; /* 0 8 */ struct device * dev; /* 8 8 */ struct net_device * netdev; /* 16 8 */ union { struct ixgbe_tx_buffer * tx_buffer_info; /* 8 */ struct ixgbe_rx_buffer * rx_buffer_info; /* 8 */ }; /* 24 8 */ long unsigned int state; /* 32 8 */ u8 atr_sample_rate; /* 40 1 */ u8 atr_count; /* 41 1 */ u16 count; /* 42 2 */ u16 rx_buf_len; /* 44 2 */ u16 next_to_use; /* 46 2 */ u16 next_to_clean; /* 48 2 */ u8 queue_index; /* 50 1 */ u8 reg_idx; /* 51 1 */ u16 work_limit; /* 52 2 */ /* XXX 2 bytes hole, try to pack */ u8 * tail; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ Now we can set the VLAN priority directly and it will be correct. User space can indicate the 802.1Qaz priority using the SO_PRIORITY setsocket() option and QOS layer will steer the skb to the correct rings. Additionally using the multiq qdisc with a queue_mapping action works as well. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
John Fastabend authored
Remove ixgbe_fcoe_getapp() and use the generic kernel routine instead. Also add application priority to the kernel maintained list on setapp so applications and stacks can query the value. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
John Fastabend authored
Implement ieee_setapp dcbnl ops in ixgbe. This is required to setup FCoE which requires dedicated resources. If the app data is not for FCoE then no action is taken in ixgbe except to add it to the dcb_app_list. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
John Fastabend authored
This implements dcbnl get and set capabilities ops. The devices supported by ixgbe can be configured to run in IEEE or CEE modes but not both. With the DCBX set capabilities bit we add an explicit signal that must be used to toggle between these modes. This patch adds logic to fail the CEE command set_hw_all() which programs the device with a CEE configuration if the CEE caps bit is not set. Similarly, IEEE set commands will fail if the IEEE caps bit is not set. We allow most CEE config set commands to occur because they do not touch the hardware until set_hw_all() is called. The one exception to the above is the {set|get}app routines. These must always be protected by caps bits to ensure side effects do not corrupt the current configured mode. By requiring the caps bit to be set correctly we can maintain a consistent configuration in the hardware for CEE or IEEE modes and prevent partial hardware configurations that may occur if user space does not send a complete IEEE or CEE configurations. It is expected that user space will signal a DCBX mode before programming device. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Carolyn Wyborny authored
This patch updates igb version to 3.0.6. Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Carolyn Wyborny authored
This patch add DMA Coalescing which is a power-saving feature that coalesces DMA writes in order to stay in a low-power state as much as possible. Feature is disabled by default. Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Carolyn Wyborny authored
This patch adds functions and functions pointers to accommodate differences between NVM interfaces and options for i350 devices, 82580 devices and the rest. Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Carolyn Wyborny authored
This patch adds the EEE feature for i350 devices, enabled by default. Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Greg Rose authored
Change the driver string to match the PF driver string format. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Greg Rose authored
The kernel version string is off by a major version number since new silicon was just introduced and also uses the wrong format for the version postfix. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 11 Mar, 2011 14 commits
-
-
Bruce Allan authored
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
The driver doesn't support Wake-on-ARP, so don't advertise through ethtool that it does. Cleanup some coding style issues in the same functions. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
If/when an OEM enables MACsec in the 82579 EEPROM, disable jumbo frames support in the driver due to an interoperability issue in hardware that prevents jumbo packets from being transmitted or received. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
When PHY reset is intentionally blocked on 82577/8/9, do not toggle the LANPHYPC value bit (essentially performing a hard power reset of the device) otherwise the PHY can be put into an unknown state. Cleanup whitespace in the same function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
The link can be unexpectedly dropped when the timer for entering EEE low- power-idle quiet state expires too soon. The timer needs to be extended from 196usec to 200usec after every LCD (PHY) reset to prevent this from happening. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
With some PHYs supported by this driver, link establishment can take a little longer when connected to certain switches. Extend the timeout to reduce the number of false diagnostic failures, and cleanup a code style issue in the same function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
Based on a report and patch originally submitted by Prasanna Panchamukhi. Use dev_kfree_skb_irq() in e1000_clean_jumbo_rx_irq() since this latter function is called only in interrupt context. This avoids "Warning: kfree_skb on hard IRQ" messages. Cc: "Prasanna S. Panchamukhi" <prasanna.panchamukhi@riverbed.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Lior Levy authored
Removed Tx hang detection mechanism from ixgbevf. This mechanism has no affect and can cause false alarm messages in some cases. Especially when VF Tx rate limit is turned on. The same mechanism was removed recently from igbvf. Signed-off-by: Lior Levy <lior.levy@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Yi Zou authored
Add proper documentation for previously added net_device_ops ops for FCoE. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
Based on a patch from Jesse Gross <jesse@nicira.com> This switches the ixgb driver to use the new VLAN interfaces. In doing this, it completes the work begun in ae54496f allowing the use of hardware VLAN insertion without having a VLAN group configured. CC: Jesse Gross <jesse@nicira.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
David S. Miller authored
Completely unused. Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
fl->oif will always be zero on the input path, so there is no reason to test for that. Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
All callers are under rcu_read_lock() protection already. Rename to ip_check_mc_rcu() to make it even more clear. Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 10 Mar, 2011 5 commits
-
-
David S. Miller authored
Conflicts: drivers/net/bnx2x/bnx2x_cmn.c
-
stephen hemminger authored
Add necessary alias to autoload ip6ip6 tunnel module. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
-
Randy Dunlap authored
When configs BRIDGE=y and IPV6=m, this build error occurs: br_multicast.c:(.text+0xa3341): undefined reference to `ipv6_dev_get_saddr' BRIDGE_IGMP_SNOOPING is boolean; if it were tristate, then adding depends on IPV6 || IPV6=n to BRIDGE_IGMP_SNOOPING would be a good fix. As it is currently, making BRIDGE depend on the IPV6 config works. Reported-by: Patrick Schaaf <netdev@bof.de> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6Linus Torvalds authored
* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: [media] mantis_pci: remove asm/pgtable.h include [media] tda829x: fix regression in probe functions [media] mceusb: don't claim multifunction device non-IR parts [media] nuvoton-cir: fix wake from suspend [media] cx18: Add support for Hauppauge HVR-1600 models with s5h1411 [media] ivtv: Fix corrective action taken upon DMA ERR interrupt to avoid hang [media] cx25840: fix probing of cx2583x chips [media] cx23885: Remove unused 'err:' labels to quiet compiler warning [media] cx23885: Revert "Check for slave nack on all transactions" [media] DiB7000M: add pid filtering [media] Fix sysfs rc protocol lookup for rc-5-sz [media] au0828: fix VBI handling when in V4L2 streaming mode [media] ir-raw: Properly initialize the IR event (BZ#27202) [media] s2255drv: firmware re-loading changes [media] Fix double free of video_device in mem2mem_testdev [media] DM04/QQBOX memcpy to const char fix
-