Merge branch 'davinci-next' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci into devel-stable

Merge branch 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel-stable

Apart from the regular AM18x/DA850/OMAP-L138 SoC operating
at 300MHz, these SoCs have variants that can operate at a
maximum of 456MHz. Variants at 408Mhz and 375 Mhz are available
as well.

Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).

The EVM hardware for all these variants is the same (except
for the actual SoC populated).

U-Boot on the EVM sets up ATAG_REVISION to inform the OS
regarding the speed grade supported by the silicon. We use
this information to pass on the speed grade information to
the SoC code.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

AM18x/DA850/OMAP-L138 SoCs have variants that can operate
at a maximum of 456 MHz at 1.3V operating point. Also the
1.2V operating point has a variant that can support a maximum
of 375 MHz.

This patch adds three new OPPs (456 MHz, 408 MHz and 372 MHz)
to the list of DA850 OPPs.

Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).

Because of this, we depend on the maximum speed grade information
to be provided to us in some board specific way. The board informs
the maximum speed grade information by setting the da850_max_speed
variable.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Use the mach-davinci/Kconfig to enable gpio-keys-polled as default when
da850-evm machine is enabled.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: "Nori, Sekhar" <nsekhar@ti.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch adds a pca953x platform device for the tca6416 found on the evm
baseboard. The tca6416 is a GPIO expander, also found on the UI board at a
separate I2C address. The pins of the baseboard IO expander are connected to
software reset, deep sleep enable, test points, a push button, DIP switches and
LEDs.

Add support for the push button, DIP switches and LEDs and test points (as
free GPIOs). The reset and deep sleep enable connections are reserved by the
setup routine so that userspace can't toggle those lines.

The existing tca6416-keypad driver was not employed because there was no
apararent way to register the LEDs connected to gpio's on the tca6416 while
simultaneously registering the tca6416-keypad instance.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
CC: Govindarajan, Sriramakrishnan <srk@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

The setup and teardown methods of the UI expander reference the SEL_{A,B,C}
pins by 'magic number' in each function. This uses the common enum for their offsets
in the expander setup and teardown functions.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Victor Rodriguez <vm.rod25@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch adds EV_KEYs for each of the 8 pushbuttons on the UI board via a
gpio-key device.

The expander is a tca6416; it controls the SEL_{A,B,C} lines which enable and
disable the peripherals found on the UI board in addition to the 8 pushbuttons
mentioned above. The reason the existing tca6416-keypad driver is not employed
is because there was no aparent way to keep the gpio lines used as
SEL_{A,B,C} registered while simultaneously registering the pushbuttons as a
tca6416-keypad instance.

Some experimentation with the polling interval was performed; we were searching
for the largest polling interval that did not affect the feel of the
responsiveness of the buttons. It is very subjective but 200ms seems to be a
good value that accepts firm pushes but rejects very light ones. The key values
assigned to the buttons were arbitrarily chosen to be F1-F8.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
CC: Govindarajan, Sriramakrishnan <srk@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

The new FPGA firmware in Balloon3 uses different methods to control it's bus
control lines. In the new version, there are separate registers to set/clear
bus control lines. This patch updates affected places.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Tested on a Colibri Evaluation Board Rev.2.1 with a Colibri PXA310 module.
Signed-off-by: Bjorn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Rename colibri-pxa270-evalboard to colibri-evalboard as this board is used with
all Colibri modules.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

This change -- pushing the MFP configuration back into Module files -- is
necessary because some evalboards can be used with multiple modules, where MFP
differs from module to module. Therefore MFP isn't board-specific, but
module-specific and the module should preconfigure itself for the board.

(And there is also the C preprocesor limitation and conflicting #define-s)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

This driver also contains structures to eventually support PXA320. This is
planned to be added in a later patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

On PXA320, there's only one PCMCIA slot available. Check for cases where the
user would want to register multiple. Also, rework failpath.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

iwmmxt is used in XScale, XScale3, Mohawk and PJ4 core. But the instructions
of accessing CP0 and CP1 is changed in PJ4. Append more files to support
iwmmxt in PJ4 core.
Signed-off-by: Zhou Zhu <zzhu3@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>

Since CPU_PJ4 is shared between PXA95x and MMP2, select CPU_PJ4 in MMP2
configuration.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Saarb platform is a handheld platform that supports Marvell PXA955 silicon.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

The core of PXA955 is PJ4. Add new PJ4 support. And add new macro
CONFIG_PXA95x.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Introduce 'struct clk' for memory and remove
get_memclk_frequency_10khz().
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Define all IRQs in irqs.h. If some IRQs are sharing one IRQ number, define
them together. If some IRQs are sharing same name with different IRQ number,
define different IRQ.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

After introducing pxa930/pxa935 and new silicons, original cpuid rules
of XScale generation 3 can't fit new silicons. Now redefine the rule
of PXA3xx.

Only PXA300/PXA310/PXA320/PXA930/PXA935 are family members of PXA3xx.
PXA930/PXA935 are family members of PXA93x. PXA93x can be considered
as PXA3xx + CP.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>