Also cleanup register specific to R300.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Also cleanup register specific to RS400/RS480. This patch also fix
legacy VGA register used to disable VGA access we were programming
wrong register. Now we should properly disable VGA on r100 up to
rs400 asics. Note that RS400/RS480 resume is broken, it hangs the
computer while reprogramming dynamic clock, doesn't work either
without that patch. We need to spend more time investigating this
issue. Version 2 of the patch remove dead code that was left
commented out in the previous version. Version 3 correct the
placement on IGP of the VRAM inside GPU address space to match the
stollen RAM placement of IGP.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Convert the r520 asic support to new init path, change are smaller than
previous one as most of the architecture is now in place and more code
sharing can happen btw various asics.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Convert the rv515 asic support to new init path also add an explanation
in radeon.h about the new init path. There is also few cleanups
associated with this change (others asic calling rv515 helper
functions).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Compiling the radeon DRM driver with !CONFIG_DEBUG_FS
throws the following warnings:

drivers/gpu/drm/radeon/radeon_ttm.c: In function 'radeon_ttm_debugfs_init':
drivers/gpu/drm/radeon/radeon_ttm.c:714: warning: unused variable 'i'
drivers/gpu/drm/radeon/radeon_ttm.c: At top level:
drivers/gpu/drm/radeon/radeon_ttm.c:692: warning: 'radeon_mem_types_list' defined but not used
drivers/gpu/drm/radeon/radeon_ttm.c:693: warning: 'radeon_mem_types_names' defined but not used

Fix: move these variables inside the #if defined(CONFIG_DEBUG_FS)
block in radeon_ttm_debugsfs_init(), which is the only place using them.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Compiling DRM throws the following warning if MAGIC_SYSRQ is disabled:

drivers/gpu/drm/drm_fb_helper.c:101: warning: 'sysrq_drm_fb_helper_restore_op' defined but not used

Fix: place sysrq_drm_fb_helper_restore_op and associated
definitions inside #ifdef CONFIG_MAGIC_SYSRQ.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dave Airlie <airlied@linux.ie>

The legacy r600 path shares code, but doesn't share quite enough
to get the freeing correct. Free the pages here also.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This initialises the fb helper with the connector helper,
so that the fb cmdline code works for intel as well.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Need add reloc offset to the offset in the actual
packet.  Fixes use of the DRAW_INDEX packet by the 3D
driver.

[airlied: modified first one where idx_value == ib[idx+0]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

All we need to do on r6xx/r7xx is clear the RADEON_IS_AGP
flag; the rest is handled in r600.c

fixes fdo bug 23990:
http://bugs.freedesktop.org/show_bug.cgi?id=23990Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Thanks to Michel for pointing this out to me, this is
why I need to get more sleep, over complicate this a bit.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Provides support for anti-tearing functionality
in the ddx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

- fix offset of NOP packet for parsing
- fix p->idx increments
- fix bad mask when updating crtc vline info
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

r6xx and r7xx was missing this.  We don't support
non-CPU accessible vram yet.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

If drivers don't init the fb helper on the connector, the cmdline
code won't work, but it shouldn't crash either.
Signed-off-by: Dave Airlie <airlied@redhat.com>

this avoids reading back the IB on AGP, also it avoids
the race where since we haven't fetched the page from the main IB
and written it to the gpu one, reading back fetches 0.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Got lots of untracked files after compiling.
These files are generated, thus should be ignored by git.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

We shouldn't need these at all in radeon kms mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>

[note this requires an fb patch posted to linux-fbdev-devel already]

This uses the normal video= command line option to control the kms
output setup at boot time. It is used to override the autodetection
done by kms.

video= normally takes a framebuffer as the first parameter, in kms
it will take a connector name, DVI-I-1, or LVDS-1 etc. If no output
connector is specified the mode string will apply to all connectors.

The mode specification used will match down the probed modes, and if
no mode is found it will add a CVT mode that matches.

video=1024x768 - all connectors match a 1024x768 mode or add a CVT on
video=VGA-1:1024x768, VGA-1 connector gets mode only.

The same strings as used in current fb modedb.c are used, except I've
added three more letters, e, D, d, e = enable, D = enable Digital,
d = disable, which allow a connector to be forced into a certain state.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Having a : should be enough 'fb:' isn't really useful
if the fb wants to a kms output ID.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This avoids needing to do a kmalloc > PAGE_SIZE for the main
indirect buffer chunk, it adds an accessor for all reads from
the chunk and caches a single page at a time for subsequent
reads.

changes since v1:
Use a two page pool which should be the most common case
a single packet spanning > PAGE_SIZE will be hit, but I'm
having trouble seeing anywhere we currently generate anything like that.
hopefully proper short page copying at end
added parser_error flag to set deep errors instead of having to test
every ib value fetch.
fixed bug in patch that went to list.
Signed-off-by: Dave Airlie <airlied@redhat.com>

when I added the property I forgot to enable it.

Thanks to soreau on #radeon for tracking it down.
Signed-off-by: Dave Airlie <airlied@redhat.com>

I never changed this back when I wrote tv-out support.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Aspect ratio code of 0 means 1:1 before EDID 1.3.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

[agd5f: also fix the non-kms path]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>

having these separate was pointless and introduced a bug when
one got updated without the other.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This patch makes sure the CP doesn't DMA do VRAM while 2D
is active by inserting a CP resync token.

todo: port to kms.
Signed-off-by: Dave Airlie <airlied@redhat.com>

RV670 was using the wrong modesetting code.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

https://bugs.freedesktop.org/show_bug.cgi?id=24041

The idle allows rs690 to startup properly.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This resumes my
RV730PRO (4650)
RV770 (4850)
fine.

Still researching the RV4550 (RV710), resumes without X fine.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Dave Airlie <airlied@redhat.com>

re-align with r600 code, to init blit earlier.
Signed-off-by: Dave Airlie <airlied@redhat.com>

We really don't want to post the card at init, it takes a relatively
long time and isn't required, so split the resume path into
a startup path called by both init/resume and separate resume
entry point to do posting.
Signed-off-by: Dave Airlie <airlied@redhat.com>

a) don't zero gart table on gart enable
b) move pinning shader object into resume path
c) unpin shader object on suspend
d) set cp ready to false after cp shutdown on suspend.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Before we use any of VRAM, we need to disable the VGA rendering
engine, this render text mode into a graphical framebuffer
for scanout, however it does this on vblank, and can end up
overwriting the GART table and r600 shader objects.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Someone on IRC reported problems after commit
95a8f1bf ('drm/radeon/kms: Move
radeon_clocks_init() call back after getting VRAM info.'). And indeed, at least
some ASIC vram_info hooks use the clock info obtained by
radeon_get_clock_info(). So, move that call out of radeon_clocks_init(), ahead
of the radeon_vram_info() call.

[airlied - fixup missing r600/rv770 calls]
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/radeon/kms: fix get clock info calls for r600/rv770 init path.

These were missed when it got split out.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This adds:
coherent mode: TMDS coherent mode for atom cards.
scaling mode: LVDS scaler mode
load detect: DAC load detection, DVI-I, VGA, TV
tmds pll: legacy TMDS pll selection
tv standard: TV standard selection.

for later: other TV ones? dvi subconnector selection using std prop

[contains fixes pointed out on dri-devel for atom bios mixups
 by Michel]
Signed-off-by: Dave Airlie <airlied@redhat.com>