1. 25 Apr, 2017 7 commits
    • Masahiro Yamada's avatar
      mtd: nand: denali: fix bitflips calculation in handle_ecc() · 20d48595
      Masahiro Yamada authored
      This function is wrong in multiple ways:
      
      [1] Counting corrected bytes instead of corrected bits.
      
      The following code is counting the number of corrected _bytes_.
      
          /* correct the ECC error */
          buf[offset] ^= err_cor_value;
          mtd->ecc_stats.corrected++;
          bitflips++;
      
      What the core framework expects is the number of corrected _bits_.
      They can be different if multiple bitflips occur within one byte.
      
      [2] total number of errors instead of max of per-sector errors
      
      The core framework expects that corrected errors are counted per
      sector, then the max value should be taken.  The current code simply
      iterates over the whole page, i.e. counts the total number of
      correction in the page.  This means "too many bitflips" is triggered
      earlier than it should be, i.e. the NAND device is worn out sooner.
      
      Besides those bugs, this function is unreadable due to the deep
      nesting.  Notice the whole code in this function is wrapped in
      if (irq_status & INTR__ECC_ERR), so this conditional can be moved
      out of the function.  Also, use shorter names for local variables.
      
      Re-work the function to fix all the issues.
      Signed-off-by: default avatarMasahiro Yamada <yamada.masahiro@socionext.com>
      Signed-off-by: default avatarBoris Brezillon <boris.brezillon@free-electrons.com>
      20d48595
    • Masahiro Yamada's avatar
      mtd: nand: denali: remove meaningless pipeline read-ahead operation · 8927ad39
      Masahiro Yamada authored
      The pipeline read-ahead function of the Denali IP enables continuous
      reading from the device; while data is being read out by a CPU, the
      controller maintains additional commands for streaming data from the
      device.  This will reduce the latency of the second page or later.
      
      This feature is obviously no help for per-page accessors of Linux
      NAND driver interface.
      
      In the current implementation, the pipeline command is issued to
      load a single page, then data are read out immediately.  The use of
      the pipeline operation is not adding any advantage, but just adding
      complexity to the code.  Remove.
      Signed-off-by: default avatarMasahiro Yamada <yamada.masahiro@socionext.com>
      Signed-off-by: default avatarBoris Brezillon <boris.brezillon@free-electrons.com>
      8927ad39
    • Masahiro Yamada's avatar
      mtd: nand: denali: allow to override mtd->name from label DT property · 8aabdf37
      Masahiro Yamada authored
      Commit 28309572 ("mtd: name the mtd device with an optional
      label property") allow us to identify a chip in a user-friendly way.
      
      If nand_set_flash_node() picks up the "label" from DT, let's respect
      it.  Otherwise, let it fallback to the current name "denali-nand".
      Signed-off-by: default avatarMasahiro Yamada <yamada.masahiro@socionext.com>
      Suggested-by: default avatarBoris Brezillon <boris.brezillon@free-electrons.com>
      Signed-off-by: default avatarBoris Brezillon <boris.brezillon@free-electrons.com>
      8aabdf37
    • Masahiro Yamada's avatar
      mtd: nand: relax ecc.read_page() return value for uncorrectable ECC · 07604686
      Masahiro Yamada authored
      The comment for ecc.read_page() requires that it should return
      "0 if bitflips uncorrectable".
      
      Actually, drivers could return positive values when uncorrectable
      bitflips occur.  For example, nand_read_page_swecc() is the case.
      If ecc.correct() returns -EBADMSG for the first ECC sector, and
      a positive value for the second one, nand_read_page_swecc() returns
      a positive max_bitflips and increments ecc_stats.failed for the same
      page.
      
      The requirement can be relaxed by tweaking nand_do_read_ops().
      Move the max_bitflips calculation below the retry.
      Signed-off-by: default avatarMasahiro Yamada <yamada.masahiro@socionext.com>
      Suggested-by: default avatarBoris Brezillon <boris.brezillon@free-electrons.com>
      Signed-off-by: default avatarBoris Brezillon <boris.brezillon@free-electrons.com>
      07604686
    • Boris Brezillon's avatar
      mtd: nand: Remove unused chip->write_page() hook · f107d7a4
      Boris Brezillon authored
      The last/only user of the chip->write_page() hook (the Atmel NAND
      controller driver) has been reworked and is no longer specifying a custom
      ->write_page() implementation.
      Drop this hook before someone else start abusing it.
      Signed-off-by: default avatarBoris Brezillon <boris.brezillon@free-electrons.com>
      Reviewed-by: default avatarMasahiro Yamada <yamada.masahiro@socionext.com>
      f107d7a4
    • Boris Brezillon's avatar
      mtd: nand: atmel: Document the new DT bindings · 82d0bf34
      Boris Brezillon authored
      The old NAND bindings were not exactly describing the hardware topology
      and were preventing definitions of several NAND chips under the same
      NAND controller.
      
      New bindings address these limitations and should be preferred over the
      old ones for new SoCs/boards.
      Old bindings are still supported for backward compatibility but are
      marked deprecated in the doc.
      Signed-off-by: default avatarBoris Brezillon <boris.brezillon@free-electrons.com>
      Reviewed-by: default avatarNicolas Ferre <nicolas.ferre@microchip.com>
      Acked-by: default avatarRob Herring <robh@kernel.org>
      82d0bf34
    • Boris Brezillon's avatar
      mtd: nand: Cleanup/rework the atmel_nand driver · f88fc122
      Boris Brezillon authored
      This is a complete rewrite of the driver whose main purpose is to
      support the new DT representation where the NAND controller node is now
      really visible in the DT and appears under the EBI bus. With this new
      representation, we can add other devices under the EBI bus without
      risking pinmuxing conflicts (the NAND controller is under the EBI
      bus logic and as such, share some of its pins with other devices
      connected on this bus).
      
      Even though the goal of this rework was not necessarily to add new
      features, the new driver has been designed with this in mind. With a
      clearer separation between the different blocks and different IP
      revisions, adding new functionalities should be easier (we already
      have plans to support SMC timing configuration so that we no longer
      have to rely on the configuration done by the bootloader/bootstrap).
      
      Also note that we no longer have a custom ->cmdfunc() implementation,
      which means we can now benefit from new features added in the core
      implementation for free (support for new NAND operations for example).
      
      The last thing that we gain with this rework is support for multi-chips
      and multi-dies chips, thanks to the clean NAND controller <-> NAND
      devices representation.
      
      During this transition we also dropped support for AVR32 SoCs which
      should soon disappear from mainline (removal of the AVR32 arch is
      planned for 4.12).
      
      This new driver has been tested on several platforms (at91sam9261,
      at91sam9g45, at91sam9x5, sama5d3 and sama5d4) to make sure it did not
      introduce regressions, and it's worth mentioning that old bindings are
      still supported (which partly explain the positive diffstat).
      Signed-off-by: default avatarBoris Brezillon <boris.brezillon@free-electrons.com>
      Acked-by: default avatarNicolas Ferre <nicolas.ferre@microchip.com>
      f88fc122
  2. 29 Mar, 2017 2 commits
  3. 28 Mar, 2017 4 commits
  4. 27 Mar, 2017 3 commits
  5. 24 Mar, 2017 11 commits
  6. 23 Mar, 2017 12 commits
  7. 16 Mar, 2017 1 commit