- 02 Aug, 2010 40 commits
-
-
Mauro Carvalho Chehab authored
Add the proper gpio port for WinTV MiniStick, with the information provided by Michael. Thanks-to: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by:Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
Simplifies the logic for handling firmware 1.20 RC messages, fixing the logic. While here, I tried to use a RC-6 remote controller from my TV set, but it didn't work with dib0700. Not sure why, but maybe this never worked. Signed-off-by: -
Mauro Carvalho Chehab authored
This patch implements change_protocol callback. With this change, there's no need for an extra modprobe parameter to specify the protocol. When a table is loaded (either from in-kernel rc-map tables or via ir-keytable program), the driver will automatically change the protocol, in order to work with the given table. Signed-off-by: -
Mauro Carvalho Chehab authored
Instead of having one big keytable with 2 protocols inside, break it into two separate tables, being one for NEC and another for RC-5 variants, and properly identify what variant should be used at the boards entries. Signed-off-by: -
Mauro Carvalho Chehab authored
a 250ms delay is too low for this device. It ends by producing false repeat events. Increase the delay time to 500 ms to avoid troubles. Signed-off-by: -
Mauro Carvalho Chehab authored
Use the new rc-core handler at dvb-usb-remote for dib0700 driver. Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Allows dvb-usb drivers to use rc-core, instead of the legacy implementation. No driver were ported yet to rc-core, so, some small adjustments may be needed, when starting to migrate the drivers. Signed-off-by: -
Mauro Carvalho Chehab authored
This is a big patch, yet trivial. It just move the RC properties to a separate struct, in order to prepare the dvb-usb drivers to use rc-core. There's no change on the behavior of the drivers. With this change, it is possible to have both legacy and rc-core based code inside the dvb-usb-remote, allowing a gradual migration to rc-core, driver per driver. Signed-off-by: -
Mauro Carvalho Chehab authored
dvb-usb has its own IR handle code. Now that we have a Remote Controller subsystem, we should start using it. So, remove this struct, in favor of the similar struct defined at the RC subsystem. This is a big, but trivial patch. It is a 3 line delect, plus lots of rename on several dvb-usb files. Signed-off-by: -
Guennadi Liakhovetski authored
RJ54N1CB0C is a Sharp camera sensor. Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Guennadi Liakhovetski authored
SH7724 datasheet specifies 480 pixels as the VOU maximum vertical resolution. This is a bug in the datasheet, VOU also supports the full PAL resolution: 576 lines. Adjust the driver accordingly. Signed-off-by:
-
Guennadi Liakhovetski authored
Using CEU with CSI2 on SH-Mobile requires some special configuration of the former. We also have to switch from calling only one subdev .s_mbus_fmt and .try_mbus_fmt to calling all subdevices. Take care to increment CSI2 driver use count to prevent it from unloading, while in use. Signed-off-by:
-
Guennadi Liakhovetski authored
Some SH-Mobile SoCs implement a MIPI CSI-2 controller, that can interface to several video clients and send data to the CEU or to the Image Signal Processor. This patch implements a v4l2-subdevice driver for CSI-2 to be used within the soc-camera framework, implementing the second subdevice in addition to the actual video clients. Signed-off-by:
-
Guennadi Liakhovetski authored
Signed-off-by:
-
Guennadi Liakhovetski authored
These formats belong to the standard format set, defined by the MIPI CSI-2 specification. Signed-off-by:
-
Guennadi Liakhovetski authored
Endianness notation is meaningless for 8 bit YUYV codes. Switch pixel code names to explicitly state the order of colour components in the data stream. Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Jarod Wilson authored
Make the bits under staging/lirc/ buildable, and add a TODO note. Signed-off-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
-
Jarod Wilson authored
Commonly found on several Hauppauge video capture devices. Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Nb: this is a very trimmed-down lirc_imon, which only supports the oldest generation of imon devices that don't do onboard signal decoding like the most recent generation imon devices -- those are now supported by the ir-core imon driver. Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
[mchehab@redhat.com: fixed a few WARNING: please, no space before tabs] Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
Michael Krufky <mkrufky@kernellabs.com> Acked-by:
Luca Olivetti <luca@ventoso.org> Signed-off-by:
-
Jarod Wilson authored
This adds support for the KWorld PlusTV 340U and KWorld UB345-Q ATSC sticks, which are really the same device. The sticks have an eMPIA em2870 usb bridge chipset, an LG Electronics LGDT3304 ATSC/QAM demodulator and an NXP TDA18271HD tuner -- early versions of the 340U have a a TDA18271HD/C1, later models and the UB435-Q have a C2. The stick has been tested succesfully with both VSB_8 and QAM_256 signals. Its using lgdt3304 support added to the lgdt3305 driver by a prior patch, rather than the current lgdt3304 driver, as its severely lacking in functionality by comparison (see said patch for details). Signed-off-by:
-
Jiri Slaby authored
In dvb_dvr_release, there is a test dvbdev->users==-1, but users are never negative. This error results in hung tasks: task PC stack pid father bash D ffffffffa000c948 0 3264 3170 0x00000000 ffff88003aec5ce8 0000000000000086 0000000000011f80 0000000000011f80 ffff88003aec5fd8 ffff88003aec5fd8 ffff88003b848670 0000000000011f80 ffff88003aec5fd8 0000000000011f80 ffff88003e02a030 ffff88003b848670 Call Trace: [<ffffffff813dd4a5>] dvb_dmxdev_release+0xc5/0x130 [<ffffffff8107b750>] ? autoremove_wake_function+0x0/0x40 [<ffffffffa00013a2>] dvb_usb_adapter_dvb_exit+0x42/0x70 [dvb_usb] [<ffffffffa0000525>] dvb_usb_exit+0x55/0xd0 [dvb_usb] [<ffffffffa00005ee>] dvb_usb_device_exit+0x4e/0x70 [dvb_usb] [<ffffffffa000a065>] af9015_usb_device_exit+0x55/0x60 [dvb_usb_af9015] [<ffffffff813a3f05>] usb_unbind_interface+0x55/0x1a0 [<ffffffff81316000>] __device_release_driver+0x70/0xe0 ... So check against 1 there instead. BTW why's the TODO there? Adding TODOs to the code without descriptions is like adding nothing. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Laurent Pinchart authored
The UVC host and gadget drivers both define constants and structures in private header files. Move all those definitions to linux/usb/video.h where they can be shared by the two drivers (and be available for userspace applications). Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by:
-
Antti Palosaari authored
Fix comments. It is demodulator driver not DVB USB -bridge. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
Firmware version is four digit long. Print all four digits instead of three digits used earlier. Signed-off-by:
-
