IO enable sequencing needs ddi clocks enabled.
These clocks will be gated at a later point in
the enable sequence.

v2: Fix the commit header (Uma)
v3: Remove the redundant read (Ville)

Fixes: 949fc52a ("drm/i915/icl: add pll mapping for DSI")
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553513202-13863-1-git-send-email-vandita.kulkarni@intel.com
(cherry picked from commit c5b81a32)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Push getting the reference for the encoders' power domains into the
encoder get_power_domains() hook instead of doing this from the caller.
This way the encoder can store away the corresponding wakerefs.

This fixes the DSI encoder disabling, which didn't release these
power references it acquired during HW state readout.

Note that longtime ownership for the corresponding wakerefs can be thus
acquired / released in two ways. Nevertheless there is always only one
owner for them:

After HW readout (booting/system resume):
- encoder->get_power_domains() acquires
- encoder->disable*() releases

After a modeset (calling intel_atomic_commit()):
- encoder->enable*() acquires
- encoder->disable*() releases

* can be any of the encoder enable/disable hooks.

v2:
- Check that the DSI io_wakerefs are unset both during encoder HW
  readout and enabling. (Chris)

Fixes: 0e6e0be4 ("drm/i915: Markup paired operations on display power domains")
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190407124655.31536-1-imre.deak@intel.com
(cherry picked from commit 3a52fb7e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

The only bpc information in pipe registers for BXT/GLK DSI
is the PIPEMISC dither bpc. Let's try to use that to read
out pipe_bpp on these platforms. However, I'm not sure if
this will be correctly populated by the GOP since bspec
suggests it's only needed if dithering is actually enabled.
If not I guess we'll have to go one step further and
extract pipe_bpp from the DSI pixel format when dithering
is disabled.

Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: ca0b04db ("drm/i915/dsi: Fix pipe_bpp for handling for 6 bpc pixel-formats")
References: https://bugs.freedesktop.org/show_bug.cgi?id=109516Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405141349.11950-1-ville.syrjala@linux.intel.com
(cherry picked from commit 49965350)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

gvt-fixes-2019-04-04

- Fix shadow mm pin count (Yan)
- Fix cmd parser error path recover (Yan)
- Fix vGPU display plane size calculation (Xiong)
- Fix kerneldoc (Chris)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190404003957.GB8327@zhen-hp.sh.intel.com

drivers/gpu/drm/i915/gvt/display.c:457: warning: Function parameter or member 'connected' not described in 'intel_vgpu_emulate_hotplug'
drivers/gpu/drm/i915/gvt/display.c:457: warning: Excess function parameter 'conncted' description in 'intel_vgpu_emulate_hotplug'

Fixes: 1ca20f33 ("drm/i915/gvt: add hotplug emulation")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Hang Yuan <hang.yuan@linux.intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

stride isn't in unit of pixel, it is bytes, so calculation of
plane size doesn't need to multiple bpp.

Fixes: e546e281 ("drm/i915/gvt: Dmabuf support for GVT-g")
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

If drm_modeset_lock() reports a deadlock it sets the ctx->contexted
field and insists that the caller calls drm_modeset_backoff() or else it
generates a WARN on cleanup.

<4> [1601.870376] WARNING: CPU: 3 PID: 8445 at drivers/gpu/drm/drm_modeset_lock.c:228 drm_modeset_drop_locks+0x35/0x40
<4> [1601.870395] Modules linked in: vgem snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic x86_pkg_temp_thermal i915 coretemp crct10dif_pclmul
<6> [1601.870403] Console: switching
<4> [1601.870403]  snd_hda_intel
<4> [1601.870406] to colour frame buffer device 320x90
<4> [1601.870406]  crc32_pclmul snd_hda_codec snd_hwdep ghash_clmulni_intel e1000e snd_hda_core cdc_ether ptp usbnet mii pps_core snd_pcm i2c_i801 mei_me mei prime_numbers
<4> [1601.870422] CPU: 3 PID: 8445 Comm: cat Tainted: G     U            5.0.0-rc7-CI-CI_DRM_5650+ #1
<4> [1601.870424] Hardware name: Intel Corporation Ice Lake Client Platform/IceLake U DDR4 SODIMM PD RVP TLC, BIOS ICLSFWR1.R00.2402.AD3.1810170014 10/17/2018
<4> [1601.870427] RIP: 0010:drm_modeset_drop_locks+0x35/0x40
<4> [1601.870430] Code: 29 48 8b 43 60 48 8d 6b 60 48 39 c5 74 19 48 8b 43 60 48 8d b8 70 ff ff ff e8 87 ff ff ff 48 8b 43 60 48 39 c5 75 e7 5b 5d c3 <0f> 0b eb d3 0f 1f 80 00 00 00 00 41 56 41 55 41 54 55 53 48 8b 6f
<4> [1601.870432] RSP: 0018:ffffc90000d67ce8 EFLAGS: 00010282
<4> [1601.870435] RAX: 00000000ffffffdd RBX: ffffc90000d67d00 RCX: 5dbbe23d00000000
<4> [1601.870437] RDX: 0000000000000000 RSI: 0000000093e6194a RDI: ffffc90000d67d00
<4> [1601.870439] RBP: ffff88849e62e678 R08: 0000000003b7329a R09: 0000000000000001
<4> [1601.870441] R10: 0000000000000000 R11: 0000000000000000 R12: ffff888492100410
<4> [1601.870442] R13: ffff88849ea50958 R14: ffff8884a67eb028 R15: ffff8884a67eb028
<4> [1601.870445] FS:  00007fa7a27745c0(0000) GS:ffff8884aff80000(0000) knlGS:0000000000000000
<4> [1601.870447] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4> [1601.870449] CR2: 000055af07e66000 CR3: 00000004a8cc2006 CR4: 0000000000760ee0
<4> [1601.870451] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
<4> [1601.870453] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
<4> [1601.870454] PKRU: 55555554
<4> [1601.870456] Call Trace:
<4> [1601.870505]  i915_dsc_fec_support_show+0x91/0x190 [i915]
<4> [1601.870522]  seq_read+0xdb/0x3c0
<4> [1601.870531]  full_proxy_read+0x51/0x80
<4> [1601.870538]  __vfs_read+0x31/0x190
<4> [1601.870546]  ? __se_sys_newfstat+0x3c/0x60
<4> [1601.870552]  vfs_read+0x9e/0x150
<4> [1601.870557]  ksys_read+0x50/0xc0
<4> [1601.870564]  do_syscall_64+0x55/0x190
<4> [1601.870569]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4> [1601.870572] RIP: 0033:0x7fa7a226d081
<4> [1601.870574] Code: fe ff ff 48 8d 3d 67 9c 0a 00 48 83 ec 08 e8 a6 4c 02 00 66 0f 1f 44 00 00 48 8d 05 81 08 2e 00 8b 00 85 c0 75 13 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 57 f3 c3 0f 1f 44 00 00 41 54 55 49 89 d4 53
<4> [1601.870576] RSP: 002b:00007ffcc05140c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
<4> [1601.870579] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007fa7a226d081
<4> [1601.870581] RDX: 0000000000020000 RSI: 000055af07e63000 RDI: 0000000000000007
<4> [1601.870583] RBP: 0000000000020000 R08: 000000000000007b R09: 0000000000000000
<4> [1601.870585] R10: 000055af07e60010 R11: 0000000000000246 R12: 000055af07e63000
<4> [1601.870587] R13: 0000000000000007 R14: 000055af07e634bf R15: 0000000000020000

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109745
Fixes: e845f099 ("drm/i915/dsc: Add Per connector debugfs node for DSC support/enable")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190329165152.29259-1-chris@chris-wilson.co.uk
(cherry picked from commit ee6df569)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Pull KVM fixes from Paolo Bonzini:
 "A collection of x86 and ARM bugfixes, and some improvements to
  documentation.

  On top of this, a cleanup of kvm_para.h headers, which were exported
  by some architectures even though they not support KVM at all. This is
  responsible for all the Kbuild changes in the diffstat"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
  Documentation: kvm: clarify KVM_SET_USER_MEMORY_REGION
  KVM: doc: Document the life cycle of a VM and its resources
  KVM: selftests: complete IO before migrating guest state
  KVM: selftests: disable stack protector for all KVM tests
  KVM: selftests: explicitly disable PIE for tests
  KVM: selftests: assert on exit reason in CR4/cpuid sync test
  KVM: x86: update %rip after emulating IO
  x86/kvm/hyper-v: avoid spurious pending stimer on vCPU init
  kvm/x86: Move MSR_IA32_ARCH_CAPABILITIES to array emulated_msrs
  KVM: x86: Emulate MSR_IA32_ARCH_CAPABILITIES on AMD hosts
  kvm: don't redefine flags as something else
  kvm: mmu: Used range based flushing in slot_handle_level_range
  KVM: export <linux/kvm_para.h> and <asm/kvm_para.h> iif KVM is supported
  KVM: x86: remove check on nr_mmu_pages in kvm_arch_commit_memory_region()
  kvm: nVMX: Add a vmentry check for HOST_SYSENTER_ESP and HOST_SYSENTER_EIP fields
  KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)
  KVM: Reject device ioctls from processes other than the VM's creator
  KVM: doc: Fix incorrect word ordering regarding supported use of APIs
  KVM: x86: fix handling of role.cr4_pae and rename it to 'gpte_size'
  KVM: nVMX: Do not inherit quadrant and invalid for the root shadow EPT
  ...

Pull x86 fixes from Thomas Gleixner:
 "A pile of x86 updates:

   - Prevent exceeding he valid physical address space in the /dev/mem
     limit checks.

   - Move all header content inside the header guard to prevent compile
     failures.

   - Fix the bogus __percpu annotation in this_cpu_has() which makes
     sparse very noisy.

   - Disable switch jump tables completely when retpolines are enabled.

   - Prevent leaking the trampoline address"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/realmode: Make set_real_mode_mem() static inline
  x86/cpufeature: Fix __percpu annotation in this_cpu_has()
  x86/mm: Don't exceed the valid physical address space
  x86/retpolines: Disable switch jump tables when retpolines are enabled
  x86/realmode: Don't leak the trampoline kernel address
  x86/boot: Fix incorrect ifdeffery scope
  x86/resctrl: Remove unused variable

Pull perf tooling fixes from Thomas Gleixner:
 "Core libraries:
   - Fix max perf_event_attr.precise_ip detection.
   - Fix parser error for uncore event alias
   - Fixup ordering of kernel maps after obtaining the main kernel map
     address.

  Intel PT:
   - Fix TSC slip where A TSC packet can slip past MTC packets so that
     the timestamp appears to go backwards.
   - Fixes for exported-sql-viewer GUI conversion to python3.

  ARM coresight:
   - Fix the build by adding a missing case value for enumeration value
     introduced in newer library, that now is the required one.

  tool headers:
   - Syncronize kernel headers with the kernel, getting new io_uring and
     pidfd_send_signal syscalls so that 'perf trace' can handle them"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf pmu: Fix parser error for uncore event alias
  perf scripts python: exported-sql-viewer.py: Fix python3 support
  perf scripts python: exported-sql-viewer.py: Fix never-ending loop
  perf machine: Update kernel map address and re-order properly
  tools headers uapi: Sync powerpc's asm/kvm.h copy with the kernel sources
  tools headers: Update x86's syscall_64.tbl and uapi/asm-generic/unistd
  tools headers uapi: Update drm/i915_drm.h
  tools arch x86: Sync asm/cpufeatures.h with the kernel sources
  tools headers uapi: Sync linux/fcntl.h to get the F_SEAL_FUTURE_WRITE addition
  tools headers uapi: Sync asm-generic/mman-common.h and linux/mman.h
  perf evsel: Fix max perf_event_attr.precise_ip detection
  perf intel-pt: Fix TSC slip
  perf cs-etm: Add missing case value

Pull CPU hotplug fixes from Thomas Gleixner:
 "Two SMT/hotplug related fixes:

   - Prevent crash when HOTPLUG_CPU is disabled and the CPU bringup
     aborts. This is triggered with the 'nosmt' command line option, but
     can happen by any abort condition. As the real unplug code is not
     compiled in, prevent the fail by keeping the CPU in zombie state.

   - Enforce HOTPLUG_CPU for SMP on x86 to avoid the above situation
     completely. With 'nosmt' being a popular option it's required to
     unplug the half brought up sibling CPUs (due to the MCE wreckage)
     completely"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smp: Enforce CONFIG_HOTPLUG_CPU when SMP=y
  cpu/hotplug: Prevent crash when CPU bringup fails on CONFIG_HOTPLUG_CPU=n

Pull locking fixlet from Thomas Gleixner:
 "Trivial update to the maintainers file"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  MAINTAINERS: Remove deleted file from futex file pattern

Pull core fixes from Thomas Gleixner:
 "A small set of core updates:

   - Make the watchdog respect the selected CPU mask again. That was
     broken by the rework of the watchdog thread management and caused
     inconsistent state and NMI watchdog being unstoppable.

   - Ensure that the objtool build can find the libelf location.

   - Remove dead kcore stub code"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  watchdog: Respect watchdog cpumask on CPU hotplug
  objtool: Query pkg-config for libelf location
  proc/kcore: Remove unused kclist_add_remap()

Pull powerpc fixes from Michael Ellerman:
 "Three non-regression fixes.

   - Our optimised memcmp could read past the end of one of the buffers
     and potentially trigger a page fault leading to an oops.

   - Some of our code to read energy management data on PowerVM had an
     endian bug leading to bogus results.

   - When reporting a machine check exception we incorrectly reported
     TLB multihits as D-Cache multhits due to a missing entry in the
     array of causes.

  Thanks to: Chandan Rajendra, Gautham R. Shenoy, Mahesh Salgaonkar,
  Segher Boessenkool, Vaidyanathan Srinivasan"

* tag 'powerpc-5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries/mce: Fix misleading print for TLB mutlihit
  powerpc/pseries/energy: Use OF accessor functions to read ibm,drc-indexes
  powerpc/64: Fix memcmp reading past the end of src/dest

Pull dmaengine fixes from Vinod Koul:

 - Revert "dmaengine: stm32-mdma: Add a check on read_u32_array" as that
   caused regression

 - Fix MAINTAINER file uniphier-mdmac.c file path

* tag 'dmaengine-fix-5.1-rc3' of git://git.infradead.org/users/vkoul/slave-dma:
  MAINTAINERS: Fix uniphier-mdmac.c file path
  dmaengine: stm32-mdma: Revert "dmaengine: stm32-mdma: Add a check on read_u32_array"

Merge tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED fixes from Jacek Anaszewski:

 - fix refcnt leak on interface rename

 - use memcpy in device_name_store() to avoid including garbage from a
   previous, longer value in the device_name

 - fix a potential NULL pointer dereference in case of_match_device()
   cannot find a match

* tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds: trigger: netdev: use memcpy in device_name_store
  leds: pca9532: fix a potential NULL pointer dereference
  leds: trigger: netdev: fix refcnt leak on interface rename

Pull GPIO fixes from Linus Walleij:
 "As you can see [in the git history] I was away on leave and Bartosz
  kindly stepped in and collected a slew of fixes, I pulled them into my
  tree in two sets and merged some two more fixes (fixing my own caused
  bugs) on top.

  Summary:

   - Revert the extended use of gpio_set_config() and think about how we
     can do this properly.

   - Fix up the SPI CS GPIO handling so it now works properly on the SPI
     bus children, as intended.

   - Error paths and driver fixes"

* tag 'gpio-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: mockup: use simple_read_from_buffer() in debugfs read callback
  gpio: of: Fix of_gpiochip_add() error path
  gpio: of: Check for "spi-cs-high" in child instead of parent node
  gpio: of: Check propname before applying "cs-gpios" quirks
  gpio: mockup: fix debugfs read
  Revert "gpio: use new gpio_set_config() helper in more places"
  gpio: aspeed: fix a potential NULL pointer dereference
  gpio: amd-fch: Fix bogus SPDX identifier
  gpio: adnp: Fix testing wrong value in adnp_gpio_direction_input
  gpio: exar: add a check for the return value of ida_simple_get fails

If userspace doesn't end the input with a newline (which can easily
happen if the write happens from a C program that does write(fd,
iface, strlen(iface))), we may end up including garbage from a
previous, longer value in the device_name. For example

# cat device_name

# printf 'eth12' > device_name
# cat device_name
eth12
# printf 'eth3' > device_name
# cat device_name
eth32

I highly doubt anybody is relying on this behaviour, so switch to
simply copying the bytes (we've already checked that size is <
IFNAMSIZ) and unconditionally zero-terminate it; of course, we also
still have to strip a trailing newline.

This is also preparation for future patches.

Fixes: 06f502f5 ("leds: trigger: Introduce a NETDEV trigger")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>

In case of_match_device cannot find a match, return -EINVAL to avoid
NULL pointer dereference.

Fixes: fa4191a6 ("leds: pca9532: Add device tree support")
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>

Pull staging driver fixes from Greg KH:
 "Here are some small staging driver fixes for 5.1-rc3, and one driver
  removal.

  The biggest thing here is the removal of the mt7621-eth driver as a
  "real" network driver was merged in 5.1-rc1 for this hardware, so this
  old driver can now be removed.

  Other than that, there are just a number of small fixes, all resolving
  reported issues and some potential corner cases for error handling
  paths.

  All of these have been in linux-next with no reported issues"

* tag 'staging-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: vt6655: Remove vif check from vnt_interrupt
  staging: erofs: keep corrupted fs from crashing kernel in erofs_readdir()
  staging: octeon-ethernet: fix incorrect PHY mode
  staging: vc04_services: Fix an error code in vchiq_probe()
  staging: erofs: fix error handling when failed to read compresssed data
  staging: vt6655: Fix interrupt race condition on device start up.
  staging: rtlwifi: Fix potential NULL pointer dereference of kzalloc
  staging: rtl8712: uninitialized memory in read_bbreg_hdl()
  staging: rtlwifi: rtl8822b: fix to avoid potential NULL pointer dereference
  staging: rtl8188eu: Fix potential NULL pointer dereference of kcalloc
  staging, mt7621-pci: fix build without pci support
  staging: speakup_soft: Fix alternate speech with other synths
  staging: axis-fifo: add CONFIG_OF dependency
  staging: olpc_dcon_xo_1: add missing 'const' qualifier
  staging: comedi: ni_mio_common: Fix divide-by-zero for DIO cmdtest
  staging: erofs: fix to handle error path of erofs_vmap()
  staging: mt7621-dts: update ethernet settings.
  staging: remove mt7621-eth

Pull tty/serial fixes from Greg KH:
 "Here are some small tty and serial driver fixes for 5.1-rc3.

  Nothing major here, just a number of potential problems fixes for
  error handling paths, as well as some other minor bugfixes for
  reported issues with 5.1-rc1.

  All of these have been in linux-next with no reported issues"

* tag 'tty-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: fix NULL pointer issue when tty_port ops is not set
  Disable kgdboc failed by echo space to /sys/module/kgdboc/parameters/kgdboc
  dt-bindings: serial: Add compatible for Mediatek MT8183
  tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped
  tty/serial: atmel: Add is_half_duplex helper
  serial: sh-sci: Fix setting SCSCR_TIE while transferring data
  serial: ar933x_uart: Fix build failure with disabled console
  tty: serial: qcom_geni_serial: Initialize baud in qcom_geni_console_setup
  sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()
  tty: mxs-auart: fix a potential NULL pointer dereference
  tty: atmel_serial: fix a potential NULL pointer dereference
  serial: max310x: Fix to avoid potential NULL pointer dereference
  serial: mvebu-uart: Fix to avoid a potential NULL pointer dereference

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 5.1-rc3.

  Nothing major at all here, just a small collection of fixes for
  reported issues, and potential problems with error handling paths.
  Also a few new device ids, as normal.

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  USB: serial: option: add Olicard 600
  USB: serial: cp210x: add new device id
  usb: u132-hcd: fix resource leak
  usb: cdc-acm: fix race during wakeup blocking TX traffic
  usb: mtu3: fix EXTCON dependency
  usb: usb251xb: fix to avoid potential NULL pointer dereference
  usb: core: Try generic PHY_MODE_USB_HOST if usb_phy_roothub_set_mode fails
  phy: sun4i-usb: Support set_mode to USB_HOST for non-OTG PHYs
  xhci: Don't let USB3 ports stuck in polling state prevent suspend
  usb: xhci: dbc: Don't free all memory with spinlock held
  xhci: Fix port resume done detection for SS ports with LPM enabled
  USB: serial: mos7720: fix mos_parport refcount imbalance on error path
  USB: gadget: f_hid: fix deadlock in f_hidg_write()
  usb: gadget: net2272: Fix net2272_dequeue()
  usb: gadget: net2280: Fix net2280_dequeue()
  usb: gadget: net2280: Fix overrun of OUT messages
  usb: dwc3: pci: add support for Comet Lake PCH ID
  usb: usb251xb: Remove unnecessary comparison of unsigned integer with >= 0
  usb: common: Consider only available nodes for dr_mode
  usb: typec: tcpm: Try PD-2.0 if sink does not respond to 3.0 source-caps
  ...

Pull ACPI fix from Rafael Wysocki:
 "This corrects a previous attempt to make Linux use its own set of ACPI
  debug flags different from the upstream ACPICA's default (Erik
  Schmauss)"

* tag 'acpi-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: use different default debug value than ACPICA

Pull power management fixes from Rafael Wysocki:
 "These fix CPU base frequency reporting in the intel_pstate driver and
  a use-after-free in the scpi-cpufreq driver.

  Specifics:

   - Fix the ACPI CPPC library to actually follow the specification when
     decoding the guaranteed performance register information and make
     the intel_pstate driver to fall back to the nominal frequency when
     reporting the base frequency if the guaranteed performance register
     information is not there (Srinivas Pandruvada).

   - Fix use-after-free in the exit callback of the scpi-cpufreq left
     after an update during the 5.0 development cycle (Vincent Stehlé)"

* tag 'pm-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: scpi: Fix use after free
  cpufreq: intel_pstate: Also use CPPC nominal_perf for base_frequency
  ACPI / CPPC: Fix guaranteed performance handling

Pull security layer fixes from James Morris:
 "Yama and LSM config fixes"

* 'fixes-v5.1-a' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  LSM: Revive CONFIG_DEFAULT_SECURITY_* for "make oldconfig"
  Yama: mark local symbols as static

Merge misc fixes from Andrew Morton:
 "22 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
  fs/proc/proc_sysctl.c: fix NULL pointer dereference in put_links
  fs: fs_parser: fix printk format warning
  checkpatch: add %pt as a valid vsprintf extension
  mm/migrate.c: add missing flush_dcache_page for non-mapped page migrate
  drivers/block/zram/zram_drv.c: fix idle/writeback string compare
  mm/page_isolation.c: fix a wrong flag in set_migratetype_isolate()
  mm/memory_hotplug.c: fix notification in offline error path
  ptrace: take into account saved_sigmask in PTRACE{GET,SET}SIGMASK
  fs/proc/kcore.c: make kcore_modules static
  include/linux/list.h: fix list_is_first() kernel-doc
  mm/debug.c: fix __dump_page when mapping->host is not set
  mm: mempolicy: make mbind() return -EIO when MPOL_MF_STRICT is specified
  include/linux/hugetlb.h: convert to use vm_fault_t
  iommu/io-pgtable-arm-v7s: request DMA32 memory, and improve debugging
  mm: add support for kmem caches in DMA32 zone
  ocfs2: fix inode bh swapping mixup in ocfs2_reflink_inodes_lock
  mm/hotplug: fix offline undo_isolate_page_range()
  fs/open.c: allow opening only regular files during execve()
  mailmap: add Changbin Du
  mm/debug.c: add a cast to u64 for atomic64_read()
  ...

Pull arm64 fix from Catalin Marinas:
 "Use memblock_alloc() instead of memblock_alloc_low() in
  request_standard_resources(), the latter being limited to the low 4G
  memory range on arm64"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: replace memblock_alloc_low with memblock_alloc

Pull IOMMU fixes from Joerg Roedel:

 - Fix a bug in the AMD IOMMU driver not handling exclusion ranges
   correctly. In fact the driver did not reserve these ranges for IOVA
   allocations, so that dma-handles could be allocated in an exclusion
   range, leading to data corruption. Exclusion ranges have not been
   used by any firmware up to now, so this issue remained undiscovered
   for quite some time.

 - Fix wrong warning messages that the IOMMU core code prints when it
   tries to allocate the default domain for an iommu group and the
   driver does not support any of the default domain types (like Intel
   VT-d).

* tag 'iommu-fixes-v5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Reserve exclusion range in iova-domain
  iommu: Don't print warning when IOMMU driver only supports unmanaged domains

Pull driver core fix from Greg KH:
 "Here is a single driver core patch for 5.1-rc3.

  After 5.1-rc1, all of the users of BUS_ATTR() are finally removed, so
  we can now drop this macro from include/linux/device.h so that no more
  new users will be created.

  This patch has been in linux-next for a while, with no reported
  issues"

* tag 'driver-core-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver core: remove BUS_ATTR()

Pull char/misc driver fixes from Greg KH:
 "Here are some binder, habanalabs, and vboxguest driver fixes for
  5.1-rc3.

  The Binder fixes resolve some reported issues found by testing, first
  by the selinux developers, and then earlier today by syzbot.

  The habanalabs fixes are all minor, resolving a number of tiny things.

  The vboxguest patches are a bit larger. They resolve the fact that
  virtual box decided to change their api in their latest release in a
  way that broke the existing kernel code, despite saying that they were
  never going to do that. So this is a bit of a "new feature", but is
  good to get merged so that 5.1 will work with the latest release. The
  changes are not large and of course virtual box "swears" they will not
  break this again, but no one is holding their breath here.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  virt: vbox: Implement passing requestor info to the host for VirtualBox 6.0.x
  binder: fix race between munmap() and direct reclaim
  binder: fix BUG_ON found by selinux-testsuite
  habanalabs: cast to expected type
  habanalabs: prevent host crash during suspend/resume
  habanalabs: perform accounting for active CS
  habanalabs: fix mapping with page size bigger than 4KB
  habanalabs: complete user context cleanup before hard reset
  habanalabs: fix bug when mapping very large memory area
  habanalabs: fix MMU number of pages calculation

Pull SCSI fixes from James Bottomley:
 "Thirteen fixes, seven of which are for IBM fibre channel and three
  additional for fairly serious bugs in drivers (qla2xxx, mpt3sas,
  aacraid).

  Of the three core fixes, the most significant is probably the missed
  run queue causing an indefinite hang. The others are fixing a
  potential use after free on device close and silencing an incorrect
  warning"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ibmvfc: Clean up transport events
  scsi: ibmvfc: Byte swap status and error codes when logging
  scsi: ibmvfc: Add failed PRLI to cmd_status lookup array
  scsi: ibmvfc: Remove "failed" from logged errors
  scsi: zfcp: reduce flood of fcrscn1 trace records on multi-element RSCN
  scsi: zfcp: fix scsi_eh host reset with port_forced ERP for non-NPIV FCP devices
  scsi: zfcp: fix rport unblock if deleted SCSI devices on Scsi_Host
  scsi: sd: Quiesce warning if device does not report optimal I/O size
  scsi: sd: Fix a race between closing an sd device and sd I/O
  scsi: core: Run queue when state is set to running after being blocked
  scsi: qla4xxx: fix a potential NULL pointer dereference
  scsi: aacraid: Insure we don't access PCIe space during AER/EEH
  scsi: mpt3sas: Fix kernel panic during expander reset

Pull i2c fixes from Wolfram Sang:
 "A new ID for the i801 driver and some Documentation fixes to make it
  easier for people to find the bindings (which is also a basis for
  further improvements in that area)"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: wmt: make bindings file name match the driver
  i2c: sun6i-p2wi: make bindings file name match the driver
  i2c: stu300: make bindings file name match the driver
  i2c: mt65xx: make bindings file name match the driver
  i2c: iop3xx: make bindings file name match the driver
  i2c: i801: Add support for Intel Comet Lake

Pull sound fixes from Takashi Iwai:
 "The important fixes at this time are a couple fixes in ALSA core: a
  fix for PCM is about the OOB access in PCM OSS plugins that has been
  for long time, but hasn't hit so often until now just because we
  allocated a large buffer via vmalloc(), and surfaced more often after
  switching to kvmalloc(). Another fix is for a long-standing PCM
  problem wrt racy PM resume.

  Others are trivial nospec coverage and usual HD-audio quirks"

* tag 'sound-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - Fix speakers on Acer Predator Helios 500 Ryzen laptops
  ALSA: pcm: Don't suspend stream in unrecoverable PCM state
  ALSA: hda/ca0132 - Simplify alt firmware loading code
  ALSA: pcm: Fix possible OOB access in PCM oss plugins
  ALSA: hda/realtek: Enable headset MIC of ASUS X430UN and X512DK with ALC256
  ALSA: hda/realtek: Enable headset mic of ASUS P5440FF with ALC256
  ALSA: hda/realtek: Enable ASUS X441MB and X705FD headset MIC with ALC256
  ALSA: hda/realtek - Add support for Acer Aspire E5-523G/ES1-432 headset mic
  ALSA: hda/realtek: Enable headset MIC of Acer Aspire Z24-890 with ALC286
  ALSA: seq: oss: Fix Spectre v1 vulnerability
  ALSA: rawmidi: Fix potential Spectre v1 vulnerability

Merge tag 'kbuild-fixes-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Remove harmful -Oz option of Clang

 - Get back the original behavior (no recursion for in-tree build) for
   GNU Make 4.x

 - Some minor fixes for coccinelle patches

 - Do not overwrite .gitignore in the output directory in case it is
   version-controlled

 - Fix missed record-mcount bug for dynamic ftrace

 - Fix endianness bug in modversions for relative CRC

 - Cater to '^H' key code in Kconfig ncurses programs

* tag 'kbuild-fixes-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig/[mn]conf: handle backspace (^H) key
  kbuild: modversions: Fix relative CRC byte order interpretation
  scripts: coccinelle: Fix description of badty.cocci
  kbuild: strip whitespace in cmd_record_mcount findstring
  kbuild: do not overwrite .gitignore in output directory
  kbuild: skip parsing pre sub-make code for recursion
  coccinelle: put_device: reduce false positives
  kbuild: skip sub-make for in-tree build with GNU Make 4.x
  Revert "kbuild: use -Oz instead of -Os when using clang"

Pull block fixes from Jens Axboe:
 "Small set of fixes that should go into this series. This contains:

   - compat signal mask fix for io_uring (Arnd)

   - EAGAIN corner case for direct vs buffered writes for io_uring
     (Roman)

   - NVMe pull request from Christoph with various little fixes

   - sbitmap ws_active fix, which caused a perf regression for shared
     tags (me)

   - sbitmap bit ordering fix (Ming)

   - libata on-stack DMA fix (Raymond)"

* tag 'for-linus-20190329' of git://git.kernel.dk/linux-block:
  nvmet: fix error flow during ns enable
  nvmet: fix building bvec from sg list
  nvme-multipath: relax ANA state check
  nvme-tcp: fix an endianess miss-annotation
  libata: fix using DMA buffers on stack
  io_uring: offload write to async worker in case of -EAGAIN
  sbitmap: order READ/WRITE freed instance and setting clear bit
  blk-mq: fix sbitmap ws_active for shared tags
  io_uring: fix big-endian compat signal mask handling
  blk-mq: update comment for blk_mq_hctx_has_pending()
  blk-mq: use blk_mq_put_driver_tag() to put tag

Pull ceph fixes from Ilya Dryomov:
 "A patch to avoid choking on multipage bvecs in the messenger and a
  small use-after-free fix"

* tag 'ceph-for-5.1-rc3' of git://github.com/ceph/ceph-client:
  ceph: fix use-after-free on symlink traversal
  libceph: fix breakage caused by multipage bvecs

Pull xfs fixes from Darrick Wong:
 "Here are a few fixes for some corruption bugs and uninitialized
  variable problems. The few patches here have gone through a few days
  worth of fstest runs with no new problems observed.

  Changes since last update:

   - Fix a bunch of static checker complaints about uninitialized
     variables and insufficient range checks.

   - Avoid a crash when incore extent map data are corrupt.

   - Disallow FITRIM when we haven't recovered the log and know the
     metadata are stale.

   - Fix a data corruption when doing unaligned overlapping dio writes"

* tag 'xfs-5.1-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: serialize unaligned dio writes against all other dio writes
  xfs: prohibit fstrim in norecovery mode
  xfs: always init bma in xfs_bmapi_write
  xfs: fix btree scrub checking with regards to root-in-inode
  xfs: dabtree scrub needs to range-check level
  xfs: don't trip over uninitialized buffer on extent read of corrupted inode

Commit 70b62c25 ("LoadPin: Initialize as ordered LSM") removed
CONFIG_DEFAULT_SECURITY_{SELINUX,SMACK,TOMOYO,APPARMOR,DAC} from
security/Kconfig and changed CONFIG_LSM to provide a fixed ordering as a
default value. That commit expected that existing users (upgrading from
Linux 5.0 and earlier) will edit CONFIG_LSM value in accordance with
their CONFIG_DEFAULT_SECURITY_* choice in their old kernel configs. But
since users might forget to edit CONFIG_LSM value, this patch revives
the choice (only for providing the default value for CONFIG_LSM) in order
to make sure that CONFIG_LSM reflects CONFIG_DEFAULT_SECURITY_* from their
old kernel configs.

Note that since TOMOYO can be fully stacked against the other legacy
major LSMs, when it is selected, it explicitly disables the other LSMs
to avoid them also initializing since TOMOYO does not expect this
currently.
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 70b62c25 ("LoadPin: Initialize as ordered LSM")
Co-developed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <james.morris@microsoft.com>

Merge tag 'perf-urgent-for-mingo-5.1-20190329' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Pull perf/urgent fixes from Arnaldo:

Core libraries:
  Jiri Olsa:
  - Fix max perf_event_attr.precise_ip detection.

  Kan Liang:
  - Fix parser error for uncore event alias

  Wei Lin:
  - Fixup ordering of kernel maps after obtaining the main kernel map address.

Intel PT:
  Adrian Hunter:
  - Fix TSC slip where A TSC packet can slip past MTC packets so that the
    timestamp appears to go backwards.

  - Fixes for exported-sql-viewer GUI conversion to python3.

ARM coresight:
  Solomon Tan:
  - Fix the build by adding a missing case value for enumeration value introduced
    in newer library, that now is the required one.

tool headers:
  Arnaldo Carvalho de Melo:
  - Syncronize kernel headers with the kernel, getting new io_uring and
    pidfd_send_signal syscalls so that 'perf trace' can handle them.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>