This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the Diamond Systems
GPIO-MM. This should make it easier for users to identify which GPIO
line corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-IDIO-16.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-IDI-48.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-DIO-48E.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Setting driver_data was necessary to access private data in the
ws16c48_remove function. Now that the ws16c48_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Setting driver_data was necessary to access private data in the
gpiomm_remove function. Now that the gpiomm_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Setting driver_data was necessary to access private data in the
idio_16_remove function. Now that the idio_16_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Setting driver_data was necessary to access private data in the
idi_48_remove function. Now that the idi_48_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Setting driver_data was necessary to access private data in the
dio48e_remove function. Now that the dio48e_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

"if (!x) WARN_ON(x)" can never trigger.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Updated and proofread the documentation for GPIO drivers a bit
when looking over the changes for generic configuration.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use regmap API to save some lines of codes and have
debugfs support for all of the MCP's registers.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There are no gpio-nalils, so fix label accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the ws16c48_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call with
the devm_gpiochip_add_data call. In addition, the gpiomm_remove function
has been removed as no longer necessary due to the use of the relevant
devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the idio_16_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the idi_48_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the dio48e_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.

Better solution is to reuse what we already have available in the
generic pinconf.

To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.

If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.

We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When a GPIO driver is backed by a pinctrl driver the GPIO driver
sometimes needs to call the pinctrl driver to configure certain things,
like whether the pin is used as input or output. In addition to this
there are other configurations applicable to GPIOs such as setting
debounce time of the GPIO.

To support this we introduce a new function pinctrl_gpio_set_config()
that can be used by gpiolib based driver to pass configuration requests
to the backing pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The current pinconf packed format allows only 16-bit argument limiting
the maximum value 65535. For most types this is enough. However,
debounce time can be in range of hundreths of milliseconds in case of
mechanical switches so we cannot represent the worst case using the
current format.

In order to support larger values change the packed format so that the
lower 8 bits are used as type which leaves 24 bits for the argument.
This allows representing values up to 16777215 and debounce times up to
16 seconds.

We also convert the existing users to use 32-bit integer when extracting
argument from the packed configuration value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Exar XR17V352/354/358 chips have 16 multi-purpose inputs/outputs which
can be controlled using gpio interface.

Add the gpio specific code.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The WinSystems WS16C48 provides registers where 8 lines of GPIO may be
set at a time. This patch add support for the set_multiple callback
function, thus allowing multiple GPIO output lines to be set more
efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Diamond Systems GPIO-MM series provides registers where 8 lines of
GPIO may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The ACCES 104-IDIO-16 series provides registers where 8 lines of GPIO
may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The ACCES 104-DIO-48E series provides registers where 8 lines of GPIO
may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a heavy edit/rewrite of the GPIO driver for the Gemini
SoC from arch/arm/mach-gemini/gpio.c.

This rewrite uses all the best-in-class helper like generic
GPIO and GPIOLIB_IRQCHIP and has been tested on ITian Square One
Gemini-based NAS/router.

Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds fairly standard DT bindings for the Cortina Systems
Gemini GPIO controller.

Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

With the current redesign of driver it's not necessary to have
custom .xlate() as the gpiolib will assign default of_gpio_simple_xlate().
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Update GPIO driver to support Multiple GPIO controllers by updating
the base of subsequent GPIO chips with total of previous chips
gpio count so that gpio_add_chip gets unique numbers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Davinci GPIO driver is implemented to work with one monolithic
Davinci GPIO platform device which may have up to Y(144) gpios.
The Davinci GPIO driver instantiates number of GPIO chips with
max 32 gpio pins per each during initialization and one IRQ domain.
So, the current GPIO's  opjects structure is:

<platform device> Davinci GPIO controller
 |- <gpio0_chip0> ------|
 ...                    |--- irq_domain (hwirq [0..143])
 |- <gpio0_chipN> ------|

Current driver creates one chip for every 32 GPIOs in a controller.
This was a limitation earlier now there is no need for that. Hence
redesigning the driver to create one gpio chip for all the ngpio
in the controller.

|- <gpio0_chip0> ------|--- irq_domain (hwirq [0..143]).

The previous discussion on this can be found here:
https://www.spinics.net/lists/linux-omap/msg132869.htmlSigned-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Remove redundant blank line.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpio2regs is written making an assumption that driver supports only
one instance of gpio controller. Removing this and adding a generic
array so as to support multiple instances of gpio controllers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The only usage of function intel_gpio_runtime_idle() is here (in the
same file):

static const struct dev_pm_ops intel_gpio_pm_ops = {
	SET_RUNTIME_PM_OPS(NULL, NULL, intel_gpio_runtime_idle)
};

And when CONFIG_PM is not set, the macro SET_RUNTIME_PM_OPS expands to
nothing, causing the following compiler warning:

drivers/gpio/gpio-intel-mid.c:324:12: warning: ‘intel_gpio_runtime_idle’
defined but not used [-Wunused-function]
static int intel_gpio_runtime_idle(struct device *dev)

Fix it by annotating the function with __maybe_unused.
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Currently all users of fwnode_get_named_gpiod() have no way to
specify a label for the GPIO. So GPIOs listed in debugfs are shown
with label "?". With this change a proper label is used.

Also adjust all users so they can pass a label, properly retrieved
from device tree properties.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Make fwnode_get_named_gpiod() consistent with the rest of
gpiod_get() like API, i.e. configure GPIO pin immediately after
request.

Besides obvious clean up it will help to configure pins based
on firmware provided resources.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Casting a pointer to an int is not portable, and provokes a compiler
warning.  Cast to unsigned long instead to avoid the warning.

drivers/gpio/gpio-mvebu.c: In function 'mvebu_gpio_probe':
drivers/gpio/gpio-mvebu.c:662:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
   soc_variant = (int) match->data;
                 ^

This will be needed when building gpio-mvebu for Armada 7k/8k ARM64
SoCs.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add optional reset-gpios pin control. If present, de-assert the
specified reset gpio pin to bring the chip out of reset.

v2:
- Specify that reset signal to PCA953x chip is active low, in
  binding doc.
- reorder includes in gpio-pca953x.c.
- remove dev_err() on devm_gpiod_get_optional() error return.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>