Stop relying on global tx ring size, reduce size for PS/mgmt queue
Signed-off-by: Felix Fietkau <nbd@nbd.name>

All members except for the struct mt76_queue pointer have been removed
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Now that AQL works well on all mt76 drivers, completely replace the arbitrary
burst sizing and number of bursts logic for tx scheduling.
For the short period of time in which AQL does not work well yet, limit each
stations to 16 in-flight packets that have no estimated tx time.
This should avoid filling the queue if a station connects and queues up a
large number of packets before rate control information is available, especially
with hardware rate control
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Since txq selection was moved to mac80211, it is no longer used
Signed-off-by: Felix Fietkau <nbd@nbd.name>

It is not needed
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Cleanup and preparation for changing tx scheduling behavior
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Their use is reversed compared to DMA. The order for DMA makes more sense,
so let's use that
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Their use is reversed compared to DMA. The order for DMA makes more sense,
so let's use that
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Some devices using MT7628 or MT7603 have only one antenna chain connected.
Detect these using the EEPROM rx/tx path settings
Reported-by: Qin Wei <me@vonger.cn>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Ensure that descriptor memory has been fully written before letting the
hardware read it
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Makes it possible to read/write them via debugfs, similar to mt7615/7603
Signed-off-by: Felix Fietkau <nbd@nbd.name>

On 7615 and newer, DMA completion only triggers unmap, but not free of queued
skbs, since pointers to packets are queued internally.
Because of that, there is no need to process the main data queue immediately
on DMA completion.
To improve performance, mask out the DMA data queue completion interrupt and
process the queue only when we receive a txfree event.
This brings the number of interrupts under load down to a small fraction.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

On 7615 and newer, DMA completion only triggers unmap, but not free of queued
skbs, since pointers to packets are queued internally.
Because of that, there is no need to process the main data queue immediately
on DMA completion.
To improve performance, mask out the DMA data queue completion interrupt and
process the queue only when we receive a txfree event.
This brings the number of interrupts under load down to a small fraction.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The previous scheduling round may have been limited by AQL.
More frames might be available after the tx free run.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Tx cleanup and tx enqueuing can run in parallel. In order to avoid queue
starvation issues under load, update q->queued immediately.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Since DMA completion does not imply tx completion, it makes more sense to
poll for airtime from mt7915_mac_tx_free.
Reduce the runtime of the function by moving all items from dev->sta_poll_list
to a local list once and process any stations that were added afterwards
on the next run
Signed-off-by: Felix Fietkau <nbd@nbd.name>

- change the WTBL LMAC access function to set the mapping window only once
- use ac * 2 as offset, since each AC has separate words for rx and tx
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix length field corruption in usb dma header introduced adding sdio
support

Fixes: 75b10f0c ("mt76: mt76u: add mt76_skb_adjust_pad utility routine")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix a possible NULL pointer dereference in mt76_testmode_dump() since
nla_nest_start returns NULL in case of error

Fixes: f0efa862 ("mt76: add API for testmode support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Initialize wcid to global_wcid if msta is NULL in mt7615_pm_wake_work
routine since wcid will be dereferenced running mt76_tx()

Fixes: 2b8cdfb2 ("mt76: mt7615: wake device before pushing frames in mt7615_tx")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix a memory leak in mt7615_tm_set_tx_power routine if
mt7615_eeprom_get_target_power_index fails.
Moreover do not account req_header twice in mcu skb allocation.

Fixes: 4f0bce1c ("mt76: mt7615: implement testmode support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use buffer allocated with kmalloc instead of with stack to fix kernel
crash due to Unable to handle kernel paging request at virtual address
ffffffc0095cbce8.

[  156.977349] Unable to handle kernel paging request at virtual address ffffffc0095cbce8
[  156.985270] Mem abort info:
[  156.988059]   ESR = 0x96000045
[  156.991104]   Exception class = DABT (current EL), IL = 32 bits
[  156.997013]   SET = 0, FnV = 0
[  157.000057]   EA = 0, S1PTW = 0
[  157.003190] Data abort info:
[  157.006061]   ISV = 0, ISS = 0x00000045
[  157.009887]   CM = 0, WnR = 1
[  157.012850] swapper pgtable: 4k pages, 39-bit VAs, pgdp = 0000000042adcba2
[  157.019715] [ffffffc0095cbce8] pgd=0000000000000000, pud=0000000000000000
[  157.026499] Internal error: Oops: 96000045 [#1] PREEMPT SMP
[  157.032065] Modules linked in: mt7663s mt7663_usb_sdio_common mt7615_common

...

[  157.073007] Process CompositorTileW (pid: 1625, stack limit = 0x000000003f2389fc)
[  157.080484] CPU: 0 PID: 1625 Comm: CompositorTileW Not tainted 4.19.137 #36
[  157.092219] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[  157.097012] pc : __memcpy+0xc0/0x180
[  157.100585] lr : swiotlb_tbl_unmap_single+0x84/0x14c
[  157.105540] sp : ffffff8008003cb0
[  157.108845] x29: ffffff8008003cb0 x28: ffffff9c1a211f60
[  157.114149] x27: ffffff9c19ecc018 x26: 0000000000001000
[  157.119452] x25: ffffff9c1a378000 x24: 0000000000000001
[  157.124755] x23: ffffff9c1a378000 x22: 00000000000001ff
[  157.130058] x21: 0000000000000000 x20: 00000000fbefe800
[  157.135360] x19: 0000000000000070 x18: 0000000000000000
[  157.140663] x17: 0000000000000000 x16: 0000000000000000
[  157.145965] x15: 0000000000000000 x14: 0000000000000000
[  157.151267] x13: 0000000000000000 x12: 000000000000000d
[  157.156569] x11: 000000000000000c x10: 0000000a7befe800
[  157.161873] x9 : fffffff680000000 x8 : 0000000000000000
[  157.167175] x7 : 0000000100000003 x6 : ffffffc0095cbce8
[  157.172479] x5 : 0000000000000000 x4 : 0000000000000000
[  157.177781] x3 : 0000000000000002 x2 : fffffffffffffff0
[  157.183085] x1 : ffffffca7befe810 x0 : ffffffc0095cbce8
[  157.188389] Call trace:
[  157.190832]  __memcpy+0xc0/0x180
[  157.194053]  swiotlb_unmap_sg_attrs+0xa8/0xb0
[  157.198406]  __swiotlb_unmap_sg_attrs+0x8c/0xa4
[  157.202931]  msdc_unprepare_data+0x6c/0x84
[  157.207019]  msdc_request_done+0x58/0x98
[  157.210934]  msdc_data_xfer_done+0x1a8/0x1d0
[  157.215195]  msdc_irq+0x12c/0x17c
[  157.218505]  __handle_irq_event_percpu+0xd8/0x298
[  157.223202]  handle_irq_event+0x60/0xdc
[  157.227031]  handle_fasteoi_irq+0xa4/0x1d4
[  157.231120]  __handle_domain_irq+0x84/0xc4
[  157.235210]  gic_handle_irq+0x124/0x1a4
[  157.239038]  el0_irq_naked+0x4c/0x54
[  157.242608] Code: 14000028 f1020042 5400024a a8c12027 (a88120c7)
[  157.248693] ---[ end trace 28b8090135b0a2e1 ]---
[  157.265589] Kernel panic - not syncing: Fatal exception in interrupt
[  157.271944] SMP: stopping secondary CPUs
[  157.275865] Kernel Offset: 0x1c10e00000 from 0xffffff8008000000
[  157.281779] CPU features: 0x0,2188200c
[  157.285519] Memory Limit: none

Fixes: a66cbdd6 ("mt76: mt7615: introduce mt7663s support")
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

MT7663s have to rely on MMC_PM_KEEP_POWER in pm_flags for to avoid SDIO
power is being shut off.

To fix sdio access failure like "mt7663s mmc1:0001:1: sdio write failed:
-22" for the first sdio command to access the bus in the resume handler.

Fixes: a66cbdd6 ("mt76: mt7615: introduce mt7663s support")
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix the following sparse warnings in mt7663s driver:

drivers/net/wireless/mediatek/mt76/mt7615/sdio_mcu.c:78:62: warning:
Using plain integer as NULL pointer
drivers/net/wireless/mediatek/mt76/mt7615/sdio_mcu.c:110:62: warning:
Using plain integer as NULL pointer
drivers/net/wireless/mediatek/mt76/mt7615/sdio_txrx.c:229:64: warning:
Using plain integer as NULL pointer
drivers/net/wireless/mediatek/mt76/mt7615/sdio_txrx.c:263:64: warning:
Using plain integer as NULL pointer

Fixes: a66cbdd6 ("mt76: mt7615: introduce mt7663s support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Reduce scope of mutex_acquire/mutex_release in mt7615_reset_test_set
routine in order to fix the following static checker warning:

drivers/net/wireless/mediatek/mt76/mt7615/debugfs.c:179
mt7615_reset_test_set()
warn: inconsistent returns 'dev->mt76.mutex'.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: ea4906c4 ("mt76: mt7615: wake device before accessing regmap in debugfs")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This disables the software A-MSDU aggregation in mac80211 and enables hardware
offloading
Suggested-by: Yiwei Chung <yiwei.chung@mediatek.com>
Suggested-by: YF Luo <yf.luo@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Indicate the filled parameter to the firmware
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use the txwi data as primary source information to avoid touching skb data
Use bitfield instead of state variable + spinlock
Signed-off-by: Felix Fietkau <nbd@nbd.name>

It is not used anywhere for this driver
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt7615 and newer drivers do not need this, since they use sequence number offload
Moving this code also reduces the number of callsites to make it easier to review
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Preparation for supporting more offload features
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Set it to 15 to match reference driver
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Queueing a per-sta work item from the tx free path can become very expensive
under load. This work is only supposed to pull rate control stats every
second and deal with rate control changes.

Additionally, the rate control update code was wrong, because it was
confusing bit masks and bit numbers in test_bit.

Fix this by introducing a dedicated device work item for rate control
updates, and by polling station stats from the phy mac work.
Stations requiring polling or rate control updates are added to lists
protected by dev->sta_poll_lock.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes a race condition where multiple tx cleanup or sta poll tasks could run
in parallel.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes a race condition where multiple tx cleanup tasks could run in parallel
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Only clear unmasked interrupts. If an interrupt is temporarily masked,
its pending events need to be processed later, even if another interrupt
happened in the mean time.
Disable interrupts in one call before scheduling
Signed-off-by: Felix Fietkau <nbd@nbd.name>

If an interrupt is temporarily masked, its pending events need to be processed
later, even if another interrupt happened in the mean time.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Only clear unmasked interrupts. If an interrupt is temporarily masked,
its pending events need to be processed later, even if another interrupt
happened in the mean time.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Avoids spurious interrupts in case the hardware was running already
Signed-off-by: Felix Fietkau <nbd@nbd.name>

A small part of the first skb buffer is passed to the firmware for parsing
via DMA, while the full buffer is passed as part of the TXP.

Avoid calling DMA unmap on the first part (with a different length than map)
Signed-off-by: Felix Fietkau <nbd@nbd.name>