This macro deduplicates a lot of similar code across the hci_debugfs.c
module. Targeting to be moved to seq_file.h eventually.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The driver may sleep in the interrupt handler.
The function call path is:
bluecard_interrupt (interrupt handler)
  bluecard_write_wakeup
    schedule_timeout --> may sleep

To fix it, schedule_timeout is replaced with mdelay.

This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

So far, kernel did not allow to advertise when there was a connection
established. With this patch kernel does allow it if controller
supports it.

If controller supports non-connectable advertising when connected, then
only non-connectable advertising instances will be advertised.
Signed-off-by: Łukasz Rymanowski <lukasz.rymanowski@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This adds the "ti,cc2560" compatible string for a TI CC2560 chip.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This adds a compatible string for the Texas Instruments CC2560 Bluetooth
chip to the existing TI WiLink shared transport bindings. These chips are
similar enough that the same bindings work for both. The file is renamed
to ti-bluetooth.txt to make it more generic.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This adds an optional nvmem consumer to get a BD address from an external
source. The BD address is then set in the Bluetooth chip after the
firmware has been loaded.

This has been tested working with a TI CC2560A chip (in a LEGO MINDSTORMS
EV3).
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This adds optional nvmem consumer properties to the ti,wlink-st device tree
bindings to allow specifying the BD address.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This adds support for setting the public address on Texas Instruments
Bluetooth chips using a vendor-specific command.

This has been tested on a CC2560A chip. The TI wiki also indicates that
this command should work on TI WL17xx/WL18xx Bluetooth chips.

During review, there was some question as to the correctness of the byte
swapping since TI's documentation is not clear on this matter. This can
be tested with the btmgmt utility from bluez. The adapter must be powered
off to change the address. If the baswap() is omitted, address is reversed.

In case there is a issue in the future, here is the output of btmon during
the command `btmgmt public-addr 00:11:22:33:44:55`:

Bluetooth monitor ver 5.43
= Note: Linux version 4.15.0-rc2-08561-gcb132a1-dirty (armv5tejl)      0.707043
= Note: Bluetooth subsystem version 2.22                               0.707091
= New Index: 00:17:E7:BD:1C:8E (Primary,UART,hci0)              [hci0] 0.707106
@ MGMT Open: btmgmt (privileged) version 1.14                 {0x0002} 0.707124
@ MGMT Open: bluetoothd (privileged) version 1.14             {0x0001} 0.707137
@ MGMT Open: btmon (privileged) version 1.14                  {0x0003} 0.707540
@ MGMT Command: Set Public Address (0x0039) plen 6    {0x0002} [hci0] 11.167991
        Address: 00:11:22:33:44:55 (CIMSYS Inc)
@ MGMT Event: Command Complete (0x0001) plen 7        {0x0002} [hci0] 11.175681
      Set Public Address (0x0039) plen 4
        Status: Success (0x00)
        Missing options: 0x00000000
@ MGMT Event: Index Removed (0x0005) plen 0           {0x0003} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0           {0x0002} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0           {0x0001} [hci0] 11.175757
= Open Index: 00:17:E7:BD:1C:8E                                [hci0] 11.176807
< HCI Command: Vendor (0x3f|0x0006) plen 6                     [hci0] 11.176975
        00 11 22 33 44 55                                .."3DU
> HCI Event: Command Complete (0x0e) plen 4                    [hci0] 11.188260
      Vendor (0x3f|0x0006) ncmd 1
        Status: Success (0x00)
...
< HCI Command: Read Local Version Info.. (0x04|0x0001) plen 0  [hci0] 11.189859
> HCI Event: Command Complete (0x0e) plen 12                   [hci0] 11.190732
      Read Local Version Information (0x04|0x0001) ncmd 1
        Status: Success (0x00)
        HCI version: Bluetooth 2.1 (0x04) - Revision 0 (0x0000)
        LMP version: Bluetooth 2.1 (0x04) - Subversion 6431 (0x191f)
        Manufacturer: Texas Instruments Inc. (13)
< HCI Command: Read BD ADDR (0x04|0x0009) plen 0               [hci0] 11.191027
> HCI Event: Command Complete (0x0e) plen 10                   [hci0] 11.192101
      Read BD ADDR (0x04|0x0009) ncmd 1
        Status: Success (0x00)
        Address: 00:11:22:33:44:55 (CIMSYS Inc)
...
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

There is already __hci_req_disable_advertising() function for disabling,
so use it.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Instead of open coding byte-by-byte printing, re-use %*ph specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This adds an endianness conversion when setting the baudrate using a
vendor-specific command. Otherwise, bad things might happen on a big-
endian system.
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This adds a #define for the vendor-specific HCI command to set the
baudrate instead of using the bare 0xff36 multiple times.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When a TI Bluetooth chip is reset, it takes about 100ms for the RTS line of
the chip to deassert. For my use case with a TI CC2560A chip, this delay
was not long enough and caused the local UART to never transmit at all (TI
AM1808 SoC UART2).

We can wait for the CTS signal using serdev_device_wait_for_cts() instead
of trying to guess using msleep().

Also changed the comment to be more informative while we are touching this
code.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The bt_* printk macros include a \n already, so we don't need extra ones
here.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

BCM43341 devices soldered onto the PCB (non-removable) always (AFAICT)
use an UART connection for bluetooth. But they also advertise btsdio
support on their 3th sdio function, this causes 2 problems:

1) A non functioning BT HCI getting registered

2) Since the btsdio driver does not have suspend/resume callbacks,
mmc_sdio_pre_suspend will return -ENOSYS, causing mmc_pm_notify()
to react as if the SDIO-card is removed and since the slot is
marked as non-removable it will never get detected as inserted again.
Which results in wifi no longer working after a suspend/resume.

This commit fixes both by making btsdio ignore BCM43341 devices
when connected to a slot which is marked non-removable.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Asus T100HA laptop uses an ACPI HID of BCM2E72 for the bluetooth
part of the SDIO bcm43340 wifi/bt combo chip.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In case of hci send frame failure, skb is still owned
by the caller (hci_core) and then should not be freed.

This fixes crash on dragonboard-410c when sending SCO
packet. skb is freed by both btqcomsmd and hci_core.

Fixes: 1511cc75 ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

John Stultz reports a boot time crash with the HiKey board (which uses
hci_serdev) occurring in hci_uart_tx_wakeup().  That function is
contained in hci_ldisc.c, but also called from the newer hci_serdev.c.
It acquires the proto_lock in struct hci_uart and it turns out that we
forgot to init the lock in the serdev code path, thus causing the crash.

John bisected the crash to commit 67d2f878 ("Bluetooth: hci_ldisc:
Allow sleeping while proto locks are held"), but the issue was present
before and the commit merely exposed it.  (Perhaps by luck, the crash
did not occur with rwlocks.)

Init the proto_lock in the serdev code path to avoid the oops.

Stack trace for posterity:

Unable to handle kernel read from unreadable memory at 406f127000
[000000406f127000] user address but active_mm is swapper
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Hardware name: HiKey Development Board (DT)
Call trace:
 hci_uart_tx_wakeup+0x38/0x148
 hci_uart_send_frame+0x28/0x38
 hci_send_frame+0x64/0xc0
 hci_cmd_work+0x98/0x110
 process_one_work+0x134/0x330
 worker_thread+0x130/0x468
 kthread+0xf8/0x128
 ret_from_fork+0x10/0x18

Link: https://lkml.org/lkml/2017/11/15/908Reported-and-tested-by: John Stultz <john.stultz@linaro.org>
Cc: Ronald Tschalär <ronald@innovation.ch>
Cc: Rob Herring <rob.herring@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Fix: drivers/bluetooth/Kconfig:35:warning: multi-line strings not
supported warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

On many laptops the btusb device is the only USB device not having USB
autosuspend enabled, this causes not only the HCI but also the USB
controller to stay awake, together using aprox. 0.4W of power.

Modern ultrabooks idle around 6W (at 50% screen brightness), 3.5W for
Apollo Lake devices. 0.4W is a significant chunk of this (7 / 11%).

The btusb driver already contains code to allow enabling USB autosuspend,
but currently leaves it up to the user / userspace to enable it. This
means that for most people it will not be enabled, leading to an
unnecessarily high power consumption.

Since enabling it is not entirely without risk of regressions, this
commit adds a Kconfig option so that Linux distributions can choose to
enable it by default. This commit also adds a module option so that when
distros receive bugs they can easily ask the user to disable it again
for easy debugging.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

* Improve jump targets so that a bit of exception handling can be better
  reused at the end of this function.

* Adjust five condition checks.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Assuming that the original code idea was to enable in-band sleeping
only if the setup_rome method returns succes and run in 'standard'
mode otherwise, we should not return setup_rome return value which
makes qca_setup fail if no rampatch/nvm file found.

This fixes BT issue on the dragonboard-820C p4 which includes the
following QCA controller:
hci0: Product:0x00000008
hci0: Patch  :0x00000111
hci0: ROM    :0x00000302
hci0: SOC    :0x00000044

Since there is no rampatch for this controller revision, just make
it work as is.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

It's been sometime I'm not involved in Bluetooth anymore but I never
got around to remove my name from it. Doing it now.

Thanks for all the fish! :)
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Eric Dumazet says:

====================
tcp: better receiver autotuning

Now TCP senders no longer backoff when a drop is detected,
it appears we are very often receive window limited.

This series makes tcp_rcv_space_adjust() slightly more robust
and responsive.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Back in linux-3.13 (commit b0983d3c ("tcp: fix dynamic right sizing"))
I addressed the pressing issues we had with receiver autotuning.

But DRS suffers from extra latencies caused by rcv_rtt_est.rtt_us
drifts. One common problem happens during slow start, since the
apparent RTT measured by the receiver can be inflated by ~50%,
at the end of one packet train.

Also, a single drop can delay read() calls by one RTT, meaning
tcp_rcv_space_adjust() can be called one RTT too late.

By replacing the tri-modal heuristic with a continuous function,
we can offset the effects of not growing 'at the optimal time'.

The curve of the function matches prior behavior if the space
increased by 25% and 50% exactly.

Cost of added multiply/divide is small, considering a TCP flow
typically would run this part of the code few times in its life.

I tested this patch with 100 ms RTT / 1% loss link, 100 runs
of (netperf -l 5), and got an average throughput of 4600 Mbit
instead of 1700 Mbit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using large tcp_rmem[2] values (I did tests with 500 MB),
I noticed overflows while computing rcvwin.

Lets fix this before the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While rcvbuf is properly clamped by tcp_rmem[2], rcvwin
is left to a potentially too big value.

It has no serious effect, since :
1) tcp_grow_window() has very strict checks.
2) window_clamp can be mangled by user space to any value anyway.

tcp_init_buffer_space() and companions use tcp_full_space(),
we use tcp_win_from_space() to avoid reloading sk->sk_rcvbuf
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since both tx_ring and first_tx are the head of tx ring, it not
necessary to use two structure members to statically indicate
the head of tx ring. So first_tx is removed.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: dead code, clean ups and slight improvements

This series contains small clean ups from John and Carl, and brings
no functional changes.

John's improvements target the flower code.  First he makes sure we don't
allocate space in FW request messages for MAC matches if the TC rule does
not contain any.  The remaining two patches remove some dead code and
unused defines.

Carl follows up with a slight optimization to his recent ethtool FW state
dumps, byte swapping input parameters once instead of the data for every
dumped item.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the requested dump level parameter to big-endian at the start of
nfp_net_dump_calculate_size() and nfp_net_dump_populate_buffer(), then
compare and assign it directly where needed in the traversal and prolog
code. This decreases the total number of conversions used.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Delete match field defines that are not supported at this time.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Port matching is selected by default on every rule so remove check for it
and delete 'else' side of the statement. Remove nfp_flower_meta_one as now
it will not feature in the code. Rename nfp_flower_meta_two given that one
has been removed.

'Additional metadata' if statement can never be true so remove it as well.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the matching of mac/mpls as a default selection. These are not
necessarily set by a TC rule (unlike the port). Previously a mac/mpls
field would exist in every match and be masked out if not used. This patch
has no impact on functionality but removes unnessary memory assignment in
the match cmsg.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GPIO polarity passed to phy-reset-gpio is ignored by the FEC
driver and it is assumed to be active low.

It can be active high only when the 'phy-reset-active-high' property
is present.

The current examples pass active high polarity and work fine, but
in order to improve the documentation make it explicit what the real
polarity is.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: Implement Stream Interleave: The I-DATA Chunk Supporting User Message Interleaving

Stream Interleave would be Implemented in two Parts:

   1. The I-DATA Chunk Supporting User Message Interleaving
   2. Interaction with Other SCTP Extensions

Overview in section 1.1 of RFC8260 for Part 1:

   This document describes a new chunk carrying payload data called
   I-DATA.  This chunk incorporates the properties of the current SCTP
   DATA chunk, all the flags and fields except the Stream Sequence
   Number (SSN), and also adds two new fields in its chunk header -- the
   Fragment Sequence Number (FSN) and the Message Identifier (MID).  The
   FSN is only used for reassembling all fragments that have the same
   MID and the same ordering property.  The TSN is only used for the
   reliable transfer in combination with Selective Acknowledgment (SACK)
   chunks.

   In addition, the MID is also used for ensuring ordered delivery
   instead of using the stream sequence number (the I-DATA chunk omits
   an SSN).

As the 1st part of Stream Interleave Implementation, this patchset adds
an ops framework named sctp_stream_interleave with a bunch of stuff that
does lots of things needed somewhere.

Then it defines sctp_stream_interleave_0 to work for normal DATA chunks
and sctp_stream_interleave_1 for I-DATA chunks.

With these functions, hundreds of if-else checks for the different process
on I-DATA chunks would be avoided. Besides, very few codes could be shared
in these two function sets.

In this patchset, it adds some basic variables, structures and socket
options firstly, then implement these functions one by one to add the
procedures for ordered idata gradually, at last adjusts some codes to
make them work for unordered idata.

To make it safe to be implemented and also not break the normal data
chunk process, this feature can't be enabled to use until all stream
interleave codes are completely accomplished.

v1 -> v2:
  - fixed a checkpatch warning that a blank line was missed.
  - avoided a kbuild warning reported from gcc-4.9.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Unordered idata process is more complicated than unordered data:

 - It has to add mid into sctp_stream_out to save the next mid value,
   which is separated from ordered idata's.

 - To support pd for unordered idata, another mid and pd_mode need to
   be added to save the message id and pd state in sctp_stream_in.

 - To make  unordered idata reasm easier, it adds a new event queue
   to save frags for idata.

The patch mostly adds the samilar reasm functions for unordered idata
as ordered idata's, and also adjusts some other codes on assign_mid,
abort_pd and ulpevent_data for idata.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

abort_pd is added as a member of sctp_stream_interleave, used to abort
partial delivery for data or idata, called in sctp_cmd_assoc_failed.

Since stream interleave allows to do partial delivery for each stream
at the same time, sctp_intl_abort_pd for idata would be very different
from the old function sctp_ulpq_abort_pd for data.

Note that sctp_ulpevent_make_pdapi will support per stream in this
patch by adding pdapi_stream and pdapi_seq in sctp_pdapi_event, as
described in section 6.1.7 of RFC6458.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

start_pd is added as a member of sctp_stream_interleave, used to
do partial_delivery for data or idata when datalen >= asoc->rwnd
in sctp_eat_data. The codes have been done in last patches, but
they need to be extracted into start_pd, so that it could be used
for SCTP_CMD_PART_DELIVER cmd as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

renege_events is added as a member of sctp_stream_interleave, used to
renege some old data or idata in reasm or lobby queue properly to free
some memory for the new data when there's memory stress.

It defines sctp_renege_events for idata, and leaves sctp_ulpq_renege
as it is for data.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enqueue_event is added as a member of sctp_stream_interleave, used to
enqueue either data, idata or notification events into user socket rx
queue.

It replaces sctp_ulpq_tail_event used in the other places with
enqueue_event.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>