Signed-off-by: John W. Linville <linville@tuxdriver.com>

We don't know yet when to restore it, implement just reading. We found
out what for are that PHY ops by comparing HT with N code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Comparison of the HT and N code has shown similarities in the ops
performed after b43_mac_phy_clock_set. That way we understood what is
happening in the HT-PHY code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Qualcomm ate up Atheros, all of the old e-mail addresses
no longer work and e-mails sent to it will bounce. Update
the addresses to the new shiny Qualcomm Atheros (QCA) ones.

Cc: stable@kernel.org
Cc: netdev@vger.kernel.org
Cc: jouni@qca.qualcomm.com
Cc: yangjie@qca.qualcomm.com
Cc: vthiagar@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I will suck out stuff to userspace to start the regulatory
revampamp, this work will be permissively licensed.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add uapsd_queues and max_sp fields to ieee80211_sta.
These fields might be needed by low-level drivers in
order to configure the AP.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add new NL80211_ATTR_STA_WME nested attribute that contains
wme params needed by the low-level driver (uapsd_queues and
max_sp).

Add these params to the station_parameters struct as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When operating as a P2P GO, we receive some P2P action frames where the
BSSID is set to the peer MAC address. Specifically, this occurs for
invitation responses. These are valid action frames and they should be
passed up.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently the aggregation is formed till the aggregation limit
is reached and the rate lookup is done for the first frame alone.
But there can be a legacy rated frames in tid queue. This patch
limits the subframe addition based on presence of legacy rate and
sends the legacy rated frames as unaggregated one.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When associating to an AP, the station might miss the first EAP
packet that the AP sends due to a race condition between the association
success procedure and the rx flow in mac80211.
In such cases, the packet might fall in ieee80211_rx_h_check due to
the fact that the relevant rx->sta wasn't allocated yet.
Allocation of the relevant station info struct before actually
sending the association request and setting it with a new
dummy_sta flag solve this problem.
The station will accept only EAP packets from the AP while it
is in the pre-association/dummy state.
This dummy station entry is not seen by normal sta_info_get()
calls, only by sta_info_get_bss_rx().
The driver is not notified for the first insertion of the
dummy station. The driver is notified only after the association
is complete and the dummy flag is removed from the station entry.
That way, all the rest of the code flow should be untouched by
this change.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Divided the sta_info_insert_rcu function to 3 mini-functions:
sta_info_insert_check - the initial checks done when inserting
a new station
sta_info_insert_ibss - the function that handles the station
addition for IBSS interfaces
sta_info_insert_non_ibss - the function that handles the station
addition in other cases

The outer API was not changed.
The refactoring was done for better usage of the different
stages in the station addition in new scenarios added
in the next commit.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We have module param called use_pio which is much easier to use.

Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since a v1 of the mesh gate series was accidentally applied, this patch
contains the changes in v2.

These are:
	- automatically make mesh gate a root node.
	- use TU_TO_EXP_TIME macro.
	- initialize timer instead of checking for NULL timer function.
	- cleanups.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since all wext specific code is removed, currently there is no
way to configure deep sleep mode. This patch removes deep sleep
configuration information in readme file.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch also deletes the now unused parts of rtl8192de/def.h.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch also deletes the now unused parts of rtl8192se/def.h.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch also removes the now unused code from rtl8192ce/def.h.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In preparation for fixing the rate-mapping situation, place a driver-agnostic
version in rtlwifi. This one contains the updated rate incormation.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Test the just-initialized value rather than some other one.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier x,y,f!={PTR_ERR,ERR_PTR,ERR_CAST};
statement S;
@@

x = f(...);
(
if (\(x == NULL\|IS_ERR(x)\)) S
|
*if (\(y == NULL\|IS_ERR(y)\))
 { ... when != x
   return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This removes the "FWxx" ID strings from the b43 and b43legacy
drivers. They were once used to match a specific driver revision
to a set of firmware files. However, this is hardly useful today.
Additionally, the IDs are not updated and maintained properly, so
they might mislead users.
Signed-off-by: Michael Buesch <m@bues.ch>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The Walsh bit is disabled for regulatory consideration.

FCC limit for walsh enable is lower than that for walsh disable. So
disabling walsh bit will not limit tx power/affect tx power even in
cases where we are not FCC limited (most client cards). If the tx
power is not FCC limited, then enabling/disabling walsh bit will
not affect Avg. EVM/overall performance in any visible manner.

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In congested network, having all rate reties at MCS rates
is failing to transmit the frame offenly. By the time reaching
the success rate set, the application gets timed out. One such
scenario is that authentication time out during 4-Way handshake.
This patch uses a legacy rate as last retry sequnce for
unaggregated frames or if the first selected rate's PER is ~80%
of max limit. And also observed from the tx status that the frame
was trasmitted successfully by using legacy rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

this useful for debugging and to keep track of success/failure of
frames such as ACK, RTS and FCS error count in a noisy environment
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The firmware keeps track of channel usage. This data can
be used by the automatic channel selection to find the best
channel.

Survey data from wlan4
	frequency:				5200 MHz [in use]
	noise:					-91 dBm
	channel active time:			811909 ms
	channel busy time:			63395 ms
	channel transmit time:			59636 ms
Survey data from wlan4
	frequency:				5210 MHz
	noise:					-91 dBm
	channel active time:			121 ms
	channel busy time:			119 ms
	channel transmit time:			0 ms
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update MAINTAINERS with NFC subsystem and drivers entry.
Signed-off-by: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We can have the NFC core layer allocating the tx head and tail
room for the drivers and avoid 1 or more SKBs copy on write on
the Tx path.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The u32 would never be less than zero so the error handling would
break.  I changed it to s32 to match how bcma_erom_get_mst_port() is
declared.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Prevent 8 bytes from being truncated from MGMT packets
when using TKIP.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We have resolved all the known issues with DMA mode, however some users
(or distros) are still forcing PIO mode by config files. Without
debugging enabled it's not noticable at all. Add the warning for them.

Cc: Gregory Bellier <gregory.bellier@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The EIFS value read from AR_D_GBL_IFS_EIFS register in core clocks and then
written back as microsecond value.
Signed-off-by: Alex Hacker <hacker@epn.ru>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

All AR9170 hardware have a 16-Bit random number generator.
The documentation claims the values are suitable for
"security keys".

The "throughput" is around 320Kibit/s. It's slow, but it
does work without introducing any special offload
firmware commands.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The firmware keeps track of channel usage. This data can
be used by the automatic channel selection to find the
*best* channel.

Survey data from wlan22
	frequency:                      2412 MHz [in use]
	noise:                          -86 dBm
	channel active time:            3339608 ms
	channel busy time:              270982 ms
	channel transmit time:          121515 ms
Survey data from wlan22
	frequency:                      2417 MHz
	noise:                          -86 dBm
	channel active time:            70 ms
	channel busy time:              2 ms
	channel transmit time:          1 ms
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Import new headers from our firmware branch:
git://git.kernel.org/pub/scm/linux/kernel/git/chr/carl9170fw.gitSigned-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

AR9170_PWR_REG_PLL_ADDAC is used to set the main clock
divisor which affects the AHB/CPU speed. Because this
would interfere with the firmware internal timekeeping,
the function has to be moved into the firmware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There was an extra semicolon so the if condition wasn't used.  We
checked "priv->dev" twice instead of "priv->mesh_dev".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

They were taken from MMIO dump with few RegExps and vim.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>