- 13 Oct, 2013 40 commits
-
-
Johan Hedberg authored
commit bf543036 upstream. We need to let the setup stage complete cleanly even when the HCI device is rfkilled. Otherwise the HCI device will stay in an undefined state and never get notified to user space through mgmt (even when it gets unblocked through rfkill). This patch makes sure that hci_dev_open() can be called in the HCI_SETUP stage, that blocking the device doesn't abort the setup stage, and that the device gets proper powered down as soon as the setup stage completes in case it was blocked meanwhile. The bug that this patch fixed can be very easily reproduced using e.g. the rfkill command line too. By running "rfkill block all" before inserting a Bluetooth dongle the resulting HCI device goes into a state where it is never announced over mgmt, not even when "rfkill unblock all" is run. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Acked-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hedberg authored
commit 5e130367 upstream. This makes it more convenient to check for rfkill (no need to check for dev->rfkill before calling rfkill_blocked()) and also avoids potential races if the RFKILL state needs to be checked from within the rfkill callback. Signed-off-by:
-
Raphael Kubo da Costa authored
commit 38a172be upstream. Yet another vendor specific ID for this chipset; this one for the ASUS USB-BT400 Bluetooth 4.0 adapter. T: Bus=03 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0b05 ProdID=17cb Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=000272C64400 C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by:
Raphael Kubo da Costa <rakuco@FreeBSD.org> Signed-off-by:
-
Peng Chen authored
commit 0a3658cc upstream. usb device info: T: Bus=06 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 15 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e005 Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms Signed-off-by:
Peng Chen <pengchen@qca.qualcomm.com> Signed-off-by:
-
Andre Guedes authored
commit 89cbb4da upstream. This patch fixes the connection encryption key size information when the host is playing the peripheral role. We should set conn->enc_key_ size in hci_le_ltk_request_evt, otherwise it is left uninitialized. Signed-off-by:
Andre Guedes <andre.guedes@openbossa.org> Signed-off-by:
-
Andre Guedes authored
commit f8776218 upstream. While playing the peripheral role, the host gets a LE Long Term Key Request Event from the controller when a connection is established with a bonded device. The host then informs the LTK which should be used for the connection. Once the link is encrypted, the host gets an Encryption Change Event. Therefore we should set conn->pending_sec_level instead of conn-> sec_level in hci_le_ltk_request_evt. This way, conn->sec_level is properly updated in hci_encrypt_change_evt. Moreover, since we have a LTK associated to the device, we have at least BT_SECURITY_MEDIUM security level. Signed-off-by:
-
Arend van Spriel authored
commit db4efbbe upstream. The driver uses platform_driver_probe() to obtain platform data if any. However, that function is placed in the .init section so it must be called upon driver module initialization. The problem was reported by Fenguang Wu resulting in a kernel oops because the .init section was already freed. [ 48.966342] Switched to clocksource tsc [ 48.970002] kernel tried to execute NX-protected page - exploit attempt? (uid: 0) [ 48.970851] BUG: unable to handle kernel paging request at ffffffff82196446 [ 48.970957] IP: [<ffffffff82196446>] classes_init+0x26/0x26 [ 48.970957] PGD 1e76067 PUD 1e77063 PMD f388063 PTE 8000000002196163 [ 48.970957] Oops: 0011 [#1] [ 48.970957] CPU: 0 PID: 17 Comm: kworker/0:1 Not tainted 3.11.0-rc7-00444-gc52dd7f #23 [ 48.970957] Workqueue: events brcmf_driver_init [ 48.970957] task: ffff8800001d2000 ti: ffff8800001d4000 task.ti: ffff8800001d4000 [ 48.970957] RIP: 0010:[<ffffffff82196446>] [<ffffffff82196446>] classes_init+0x26/0x26 [ 48.970957] RSP: 0000:ffff8800001d5d40 EFLAGS: 00000286 [ 48.970957] RAX: 0000000000000001 RBX: ffffffff820c5620 RCX: 0000000000000000 [ 48.970957] RDX: 0000000000000001 RSI: ffffffff816f7380 RDI: ffffffff820c56c0 [ 48.970957] RBP: ffff8800001d5d50 R08: ffff8800001d2508 R09: 0000000000000002 [ 48.970957] R10: 0000000000000000 R11: 0001f7ce298c5620 R12: ffff8800001c76b0 [ 48.970957] R13: ffffffff81e91d40 R14: 0000000000000000 R15: ffff88000e0ce300 [ 48.970957] FS: 0000000000000000(0000) GS:ffffffff81e84000(0000) knlGS:0000000000000000 [ 48.970957] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 48.970957] CR2: ffffffff82196446 CR3: 0000000001e75000 CR4: 00000000000006b0 [ 48.970957] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 48.970957] DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000 [ 48.970957] Stack: [ 48.970957] ffffffff816f7df8 ffffffff820c5620 ffff8800001d5d60 ffffffff816eeec9 [ 48.970957] ffff8800001d5de0 ffffffff81073dc5 ffffffff81073d68 ffff8800001d5db8 [ 48.970957] 0000000000000086 ffffffff820c5620 ffffffff824f7fd0 0000000000000000 [ 48.970957] Call Trace: [ 48.970957] [<ffffffff816f7df8>] ? brcmf_sdio_init+0x18/0x70 [ 48.970957] [<ffffffff816eeec9>] brcmf_driver_init+0x9/0x10 [ 48.970957] [<ffffffff81073dc5>] process_one_work+0x1d5/0x480 [ 48.970957] [<ffffffff81073d68>] ? process_one_work+0x178/0x480 [ 48.970957] [<ffffffff81074188>] worker_thread+0x118/0x3a0 [ 48.970957] [<ffffffff81074070>] ? process_one_work+0x480/0x480 [ 48.970957] [<ffffffff8107aa17>] kthread+0xe7/0xf0 [ 48.970957] [<ffffffff810829f7>] ? finish_task_switch.constprop.57+0x37/0xd0 [ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80 [ 48.970957] [<ffffffff81a6923a>] ret_from_fork+0x7a/0xb0 [ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80 [ 48.970957] Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc [ 48.970957] RIP [<ffffffff82196446>] classes_init+0x26/0x26 [ 48.970957] RSP <ffff8800001d5d40> [ 48.970957] CR2: ffffffff82196446 [ 48.970957] ---[ end trace 62980817cd525f14 ]--- Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Tested-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Maxim Patlasov authored
commit 0ab08f57 upstream. A former patch introducing FUSE_I_SIZE_UNSTABLE flag provided detailed description of races between ftruncate and anyone who can extend i_size: > 1. As in the previous scenario fuse_dentry_revalidate() discovered that i_size > changed (due to our own fuse_do_setattr()) and is going to call > truncate_pagecache() for some 'new_size' it believes valid right now. But by > the time that particular truncate_pagecache() is called ... > 2. fuse_do_setattr() returns (either having called truncate_pagecache() or > not -- it doesn't matter). > 3. The file is extended either by write(2) or ftruncate(2) or fallocate(2). > 4. mmap-ed write makes a page in the extended region dirty. This patch adds necessary bits to fuse_file_fallocate() to protect from that race. Signed-off-by:
Maxim Patlasov <mpatlasov@parallels.com> Signed-off-by:
Miklos Szeredi <mszeredi@suse.cz> Signed-off-by:
-
Maxim Patlasov authored
commit bde52788 upstream. The patch fixes a race between mmap-ed write and fallocate(PUNCH_HOLE): 1) An user makes a page dirty via mmap-ed write. 2) The user performs fallocate(2) with mode == PUNCH_HOLE|KEEP_SIZE and <offset, size> covering the page. 3) Before truncate_pagecache_range call from fuse_file_fallocate, the page goes to write-back. The page is fully processed by fuse_writepage (including end_page_writeback on the page), but fuse_flush_writepages did nothing because fi->writectr < 0. 4) truncate_pagecache_range is called and fuse_file_fallocate is finishing by calling fuse_release_nowrite. The latter triggers processing queued write-back request which will write stale data to the hole soon. Changed in v2 (thanks to Brian for suggestion): - Do not truncate page cache until FUSE_FALLOCATE succeeded. Otherwise, we can end up in returning -ENOTSUPP while user data is already punched from page cache. Use filemap_write_and_wait_range() instead. Changed in v3 (thanks to Miklos for suggestion): - fuse_wait_on_writeback() is prone to livelocks; use fuse_set_nowrite() instead. So far as we need a dirty-page barrier only, fuse_sync_writes() should be enough. - rebased to for-linus branch of fuse.git Signed-off-by:
-
Paul E. McKenney authored
commit 8f21bd00 upstream. The csum_partial_copy_generic() function saves the PowerPC non-volatile r14, r15, and r16 registers for the main checksum-and-copy loop. Unfortunately, it fails to restore them upon error exit from this loop, which results in silent corruption of these registers in the presumably rare event of an access exception within that loop. This commit therefore restores these register on error exit from the loop. Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Madhavan Srinivasan authored
commit d1211af3 upstream. arch/powerpc/kernel/sysfs.c exports PURR with write permission. This may be valid for kernel in phyp mode. But writing to the file in guest mode causes crash due to a priviledge violation Signed-off-by:
Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by:
-
Paul E. McKenney authored
commit d9813c36 upstream. The csum_partial_copy_generic() uses register r7 to adjust the remaining bytes to process. Unfortunately, r7 also holds a parameter, namely the address of the flag to set in case of access exceptions while reading the source buffer. Lacking a quantum implementation of PowerPC, this commit instead uses register r9 to do the adjusting, leaving r7's pointer uncorrupted. Signed-off-by:
-
Prarit Bhargava authored
commit e82b89a6 upstream. modalias_show() should return an empty string on error, not -ENODEV. This causes the following false and annoying error: > find /sys/devices -name modalias -print0 | xargs -0 cat >/dev/null cat: /sys/devices/vio/4000/modalias: No such device cat: /sys/devices/vio/4001/modalias: No such device cat: /sys/devices/vio/4002/modalias: No such device cat: /sys/devices/vio/4004/modalias: No such device cat: /sys/devices/vio/modalias: No such device Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Signed-off-by:
-
Michael Neuling authored
commit e9bdc3d6 upstream. When we do a treclaim or trecheckpoint we end up running with userspace PPR and DSCR values. Currently we don't do anything special to avoid running with user values which could cause a severe performance degradation. This patch moves the PPR and DSCR save and restore around treclaim and trecheckpoint so that we run with user values for a much shorter period. More care is taken with the PPR as it's impact is greater than the DSCR. This is similar to user exceptions, where we run HTM_MEDIUM early to ensure that we don't run with a userspace PPR values in the kernel. Signed-off-by:
Michael Neuling <mikey@neuling.org> Signed-off-by:
-
Michael Ellerman authored
commit a53b27b3 upstream. Commit 4df48999 "Add power8 EBB support" included a bug in the handling of the FAB_CRESP_MATCH and FAB_TYPE_MATCH fields. These values are pulled out of the event code using EVENT_THR_CTL_SHIFT, however we were then or'ing that value directly into MMCR1. This meant we were failing to set the FAB fields correctly, and also potentially corrupting the value for PMC4SEL. Leading to no counts for the FAB events and incorrect counts for PMC4. The fix is simply to shift left the FAB value correctly before or'ing it with MMCR1. Reported-by:
Sooraj Ravindran Nair <soonair3@in.ibm.com> Signed-off-by:
Michael Ellerman <michael@ellerman.id.au> Signed-off-by:
-
Nishanth Aravamudan authored
commit 1cf389df upstream. Under heavy (DLPAR?) stress, we tripped this panic() in arch/powerpc/kernel/iommu.c::iommu_init_table(): page = alloc_pages_node(nid, GFP_ATOMIC, get_order(sz)); if (!page) panic("iommu_init_table: Can't allocate %ld bytes\n", sz); Before the panic() we got a page allocation failure for an order-2 allocation. There appears to be memory free, but perhaps not in the ATOMIC context. I looked through all the call-sites of iommu_init_table() and didn't see any obvious reason to need an ATOMIC allocation. Most call-sites in fact have an explicit GFP_KERNEL allocation shortly before the call to iommu_init_table(), indicating we are not in an atomic context. There is some indirection for some paths, but I didn't see any locks indicating that GFP_KERNEL is inappropriate. With this change under the same conditions, we have not been able to reproduce the panic. Signed-off-by:
Nishanth Aravamudan <nacc@us.ibm.com> Signed-off-by:
-
Dan Carpenter authored
commit d63733ae upstream. If the user passes an invalid value it leads to an info leak when we print the error message or it could oops. This is called with user supplied data from snd_ctl_elem_write(). Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
-
Dan Carpenter authored
commit d967967e upstream. This is called from snd_ctl_elem_write() with user supplied data so we need to add some bounds checking. Signed-off-by:
-
Dan Carpenter authored
commit f8d7b13e upstream. The ->put() function are called from snd_ctl_elem_write() with user supplied data. The limit checks here could underflow leading to a crash. Signed-off-by:
-
Javier Martinez Canillas authored
commit fac7fa16 upstream. The OMAP GPIO controller HW requires a pin to be configured in GPIO input mode in order to operate as an interrupt input. Since drivers should not be aware of whether an interrupt pin is also a GPIO or not, the HW should be fully configured/enabled as an IRQ if a driver solely uses IRQ APIs such as request_irq(), and never calls any GPIO-related APIs. As such, add the missing HW setup to the OMAP GPIO controller's irq_chip driver. Since this bypasses the GPIO subsystem we have to ensure that another driver won't be able to request the same GPIO pin that is used as an IRQ and set its direction as output. Requesting the GPIO and setting its direction as input is allowed though. This fixes smsc911x ethernet support for tobi and igep OMAP3 boards and OMAP4 SDP SPI based ethernet that use a GPIO as an interrupt line. Acked-by:
Stephen Warren <swarren@nvidia.com> Tested-by:
George Cherian <george.cherian@ti.com> Tested-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Tested-by:
Lars Poeschel <poeschel@lemonage.de> Reviewed-by:
Kevin Hilman <khilman@linaro.org> Tested-by:
Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Javier Martinez Canillas authored
commit fa365e4d upstream. The GPIO OMAP controller pins can be used as IRQ and GPIO independently so is necessary to keep track GPIO pins and IRQ lines usage separately to make sure that the bank will always be enabled while being used. Also move gpio_is_input() definition in preparation for the next patch that setups the controller's irq_chip driver when a caller requests an interrupt line. Acked-by:
-
Dan Aloni authored
commit 72023656 upstream. A high setting of max_map_count, and a process core-dumping with a large enough vm_map_count could result in an NT_FILE note not being written, and the kernel crashing immediately later because it has assumed otherwise. Reproduction of the oops-causing bug described here: https://lkml.org/lkml/2013/8/30/50 Rge ussue originated in commit 2aa362c4 ("coredump: extend core dump note section to contain file names of mapped file") from Oct 4, 2012. This patch make that section optional in that case. fill_files_note() should signify the error, and also let the info struct in elf_core_dump() be zero-initialized so that we can check for the optionally written note. [akpm@linux-foundation.org: avoid abusing E2BIG, remove a couple of not-really-needed local variables] [akpm@linux-foundation.org: fix sparse warning] Signed-off-by:
Dan Aloni <alonid@stratoscale.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Denys Vlasenko <vda.linux@googlemail.com> Reported-by:
Martin MOKREJS <mmokrejs@gmail.com> Tested-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Gabor Juhos authored
commit 1b0135b5 upstream. Since commit 01426478 (avr32: Use generic idle loop) the kernel throws the following warning on avr32: WARNING: at 900322e4 [verbose debug info unavailable] Modules linked in: CPU: 0 PID: 0 Comm: swapper Not tainted 3.12.0-rc2 #117 task: 901c3ecc ti: 901c0000 task.ti: 901c0000 PC is at cpu_idle_poll_ctrl+0x1c/0x38 LR is at comparator_mode+0x3e/0x40 pc : [<900322e4>] lr : [<90014882>] Not tainted sp : 901c1f74 r12: 00000000 r11: 901c74a0 r10: 901d2510 r9 : 00000001 r8 : 901db4de r7 : 901c74a0 r6 : 00000001 r5 : 00410020 r4 : 901db574 r3 : 00410024 r2 : 90206fe0 r1 : 00000000 r0 : 007f0000 Flags: qvnzc Mode bits: hjmde....G CPU Mode: Supervisor Call trace: [<90039ede>] clockevents_set_mode+0x16/0x2e [<90039f00>] clockevents_shutdown+0xa/0x1e [<9003a078>] clockevents_exchange_device+0x58/0x70 [<9003a78c>] tick_check_new_device+0x38/0x54 [<9003a1a2>] clockevents_register_device+0x32/0x90 [<900035c4>] time_init+0xa8/0x108 [<90000520>] start_kernel+0x128/0x23c When the 'avr32_comparator' clockevent device is registered, the clockevent core sets the mode of that clockevent device to CLOCK_EVT_MODE_SHUTDOWN. Due to this, the 'comparator_mode' function calls the 'cpu_idle_poll_ctrl' to disables idle poll. This results in the aforementioned warning because the polling is not enabled yet. Change the code to only disable idle poll if it is enabled by the same function to avoid the warning. Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Acked-by:
Hans-Christian Egtvedt <egtvedt@samfundet.no> Signed-off-by:
-
Nicolas Dichtel authored
[ Upstream commit bb814094 ] rtnl ops where introduced by c075b130 ("ip6tnl: advertise tunnel param via rtnl"), but I forget to assign rtnl ops to fb tunnels. Now that it is done, we must remove the explicit call to unregister_netdevice_queue(), because the fallback tunnel is added to the queue in ip6_tnl_destroy_tunnels() when checking rtnl_link_ops of all netdevices (this is valid since commit 0bd87628 ("ip6tnl: add x-netns support")). Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Nicolas Dichtel authored
[ Upstream commit 205983c4 ] rtnl ops where introduced by ba3e3f50 ("sit: advertise tunnel param via rtnl"), but I forget to assign rtnl ops to fb tunnels. Now that it is done, we must remove the explicit call to unregister_netdevice_queue(), because the fallback tunnel is added to the queue in sit_destroy_tunnels() when checking rtnl_link_ops of all netdevices (this is valid since commit 5e6700b3 ("sit: add support of x-netns")). Signed-off-by:
-
Steffen Klassert authored
[ Upstream commit 3e08f4a7 ] We might extend the used aera of a skb beyond the total headroom when we install the ipip header. Fix this by calling skb_cow_head() unconditionally. Bug was introduced with commit c5441932 ("GRE: Refactor GRE tunneling code.") Cc: Pravin Shelar <pshelar@nicira.com> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Ricardo Ribalda authored
[ Upstream commit 7167cf0e ] The dma descriptors indexes are only initialized on the probe function. If a packet is on the buffer when temac_stop is called, the dma descriptors indexes can be left on a incorrect state where no other package can be sent. So an interface could be left in an usable state after ifdow/ifup. This patch makes sure that the descriptors indexes are in a proper status when the device is open. Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
-
Salam Noureddine authored
[ Upstream commit 9260d3e1 ] It is possible for the timer handlers to run after the call to ipv6_mc_down so use in6_dev_put instead of __in6_dev_put in the handler function in order to do proper cleanup when the refcnt reaches 0. Otherwise, the refcnt can reach zero without the inet6_dev being destroyed and we end up leaking a reference to the net_device and see messages like the following, unregister_netdevice: waiting for eth0 to become free. Usage count = 1 Tested on linux-3.4.43. Signed-off-by:
Salam Noureddine <noureddine@aristanetworks.com> Signed-off-by:
-
Salam Noureddine authored
[ Upstream commit e2401654 ] It is possible for the timer handlers to run after the call to ip_mc_down so use in_dev_put instead of __in_dev_put in the handler function in order to do proper cleanup when the refcnt reaches 0. Otherwise, the refcnt can reach zero without the in_device being destroyed and we end up leaking a reference to the net_device and see messages like the following, unregister_netdevice: waiting for eth0 to become free. Usage count = 1 Tested on linux-3.4.43. Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 3da812d8 ] gre_hlen already accounts for sizeof(struct ipv6_hdr) + gre header, so initialize max_headroom to zero. Otherwise the if (encap_limit >= 0) { max_headroom += 8; mtu -= 8; } increments an uninitialized variable before max_headroom was reset. Found with coverity: 728539 Cc: Dmitry Kozlov <xeb@mail.ru> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Neil Horman authored
[ Upstream commit 5a0068de ] Recently grabbed this report: https://bugzilla.redhat.com/show_bug.cgi?id=1005567 Of an issue in which the bonding driver, with an attached vlan encountered the following errors when bond0 was taken down and back up: dummy1: promiscuity touches roof, set promiscuity failed. promiscuity feature of device might be broken. The error occurs because, during __bond_release_one, if we release our last slave, we take on a random mac address and issue a NETDEV_CHANGEADDR notification. With an attached vlan, the vlan may see that the vlan and bond mac address were in sync, but no longer are. This triggers a call to dev_uc_add and dev_set_rx_mode, which enables IFF_PROMISC on the bond device. Then, when we complete __bond_release_one, we use the current state of the bond flags to determine if we should decrement the promiscuity of the releasing slave. But since the bond changed promiscuity state during the release operation, we incorrectly decrement the slave promisc count when it wasn't in promiscuous mode to begin with, causing the above error Fix is pretty simple, just cache the bonding flags at the start of the function and use those when determining the need to set promiscuity. This is also needed for the ALLMULTI flag Reported-by:
Mark Wu <wudxw@linux.vnet.ibm.com> CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Mark Wu <wudxw@linux.vnet.ibm.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by:
-
Peter Korsgaard authored
[ Upstream commit bf0ea638 ] Pass-all-multicast is controlled by bit 3 in RX control, not bit 2 (pass undersized frames). Reported-by:
Joseph Chang <joseph_chang@davicom.com.tw> Signed-off-by:
Peter Korsgaard <peter@korsgaard.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 9a3bab6b ] A host might need net_secret[] and never open a single socket. Problem added in commit aebda156 ("net: defer net_secret[] initialization") Based on prior patch from Hannes Frederic Sowa. Reported-by:
Hannes Frederic Sowa <hannes@strressinduktion.org> Signed-off-by:
-
Catalin(ux) M. BOIE authored
[ Upstream commit 7df37ff3 ] When a router is doing DNAT for 6to4/6rd packets the latest anti-spoofing commit 218774dc ("ipv6: add anti-spoofing checks for 6to4 and 6rd") will drop them because the IPv6 address embedded does not match the IPv4 destination. This patch will allow them to pass by testing if we have an address that matches on 6to4/6rd interface. I have been hit by this problem using Fedora and IPV6TO4_IPV4ADDR. Also, log the dropped packets (with rate limit). Signed-off-by:
Catalin(ux) M. BOIE <catab@embedromix.ro> Acked-by:
-
Roger Luethi authored
[ Upstream commit 207070f5 ] Outgoing packets sent by via-rhine have their VLAN PCP field off by one (when hardware acceleration is enabled). The TX descriptor expects only VID and PCP (without a CFI/DEI bit). Peter Boström noticed and reported the bug. Signed-off-by:
Roger Luethi <rl@hellgate.ch> Cc: Peter Boström <peter.bostrom@netrounds.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 2811ebac ] In the following scenario the socket is corked: If the first UDP packet is larger then the mtu we try to append it to the write queue via ip6_ufo_append_data. A following packet, which is smaller than the mtu would be appended to the already queued up gso-skb via plain ip6_append_data. This causes random memory corruptions. In ip6_ufo_append_data we also have to be careful to not queue up the same skb multiple times. So setup the gso frame only when no first skb is available. This also fixes a shortcoming where we add the current packet's length to cork->length but return early because of a packet > mtu with dontfrag set (instead of sutracting it again). Found with trinity. Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Ansis Atteka authored
[ Upstream commit 703133de ] If local fragmentation is allowed, then ip_select_ident() and ip_select_ident_more() need to generate unique IDs to ensure correct defragmentation on the peer. For example, if IPsec (tunnel mode) has to encrypt large skbs that have local_df bit set, then all IP fragments that belonged to different ESP datagrams would have used the same identificator. If one of these IP fragments would get lost or reordered, then peer could possibly stitch together wrong IP fragments that did not belong to the same datagram. This would lead to a packet loss or data corruption. Signed-off-by:
Ansis Atteka <aatteka@nicira.com> Signed-off-by:
-
Ansis Atteka authored
[ Upstream commit 749154aa ] skb->data already points to IP header, but for the sake of consistency we can also use ip_hdr() to retrieve it. Signed-off-by:
-
Duan Jiong authored
[ Upstream commit bd784a14 ] DCCP shouldn't be setting sk_err on redirects as it isn't an error condition. it should be doing exactly what tcp is doing and leaving the error handler without touching the socket. Signed-off-by:
Duan Jiong <duanj.fnst@cn.fujitsu.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit 3f96a532 ] Adapt the same behaviour for SCTP as present in TCP for ICMP redirect messages. For IPv6, RFC4443, section 2.4. says: ... (e) An ICMPv6 error message MUST NOT be originated as a result of receiving the following: ... (e.2) An ICMPv6 redirect message [IPv6-DISC]. ... Therefore, do not report an error to user space, just invoke dst's redirect callback and leave, same for IPv4 as done in TCP as well. The implication w/o having this patch could be that the reception of such packets would generate a poll notification and in worst case it could even tear down the whole connection. Therefore, stop updating sk_err on redirects. Reported-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Signed-off-by:
-
