- 20 Aug, 2016 40 commits
-
-
Huacai Chen authored
commit 3ef06653 upstream. At first, we prefer to use mips clockevent device, so we decrease the rating of hpet clockevent device. For hpet, if HPET_MIN_PROG_DELTA (minimum delta of hpet programming) is too small and HPET_MIN_CYCLES (threshold of -ETIME checking) is too large, then hpet_next_event() can easily return -ETIME. After commit c6eb3f70 ("hrtimer: Get rid of hrtimer softirq") this will cause a RCU stall. So, HPET_MIN_PROG_DELTA must be sufficient that we don't re-trip the -ETIME check -- if we do, we will return -ETIME, forward the next event time, try to set it, return -ETIME again, and basically lock the system up. Meanwhile, HPET_MIN_CYCLES doesn't need to be too large, 16 cycles is enough. This solution is similar to commit f9eccf24 ("clocksource/drivers /vt8500: Increase the minimum delta"). By the way, this patch ensures hpet count/compare to be 32-bit long. Signed-off-by:
Huacai Chen <chenhc@lemote.com> Cc: John Crispin <john@phrozen.org> Cc: Steven J . Hill <Steven.Hill@imgtec.com> Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13819/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Huacai Chen authored
commit 07d69579 upstream. Don't register r4k sched clock when CPUFREQ enabled because sched clock need a constant frequency. Signed-off-by:
-
Matt Redfearn authored
commit 4f53989b upstream. Commit a168b8f1 ("MIPS: mm: Add MIPS R6 instruction encodings") added an incorrect definition of the redefined MIPSr6 cache instruction. Executing any kernel code including this instuction results in a reserved instruction exception and kernel panic. Fix the instruction definition. Fixes: a168b8f1Signed-off-by:
Matt Redfearn <matt.redfearn@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13663/Signed-off-by:
-
Trond Myklebust authored
commit db1bb44c upstream. We're always tracing IPv4 or IPv6 addresses, so we can save a lot of space on the ringbuffer by allocating the correct sockaddr size. Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Fixes: 83a712e0 "sunrpc: add some tracepoints around ..." Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
KT Liao authored
commit 2de4fcc6 upstream. Some ASUS laptops were shipped with touchpads that require to be woken up first, before trying to switch them into absolute reporting mode, otherwise touchpad would fail to work while flooding the logs with: elan_i2c i2c-ELAN1000:00: invalid report id data (1) Among affected devices are Asus E202SA, N552VW, X456UF, UX305CA, and others. We detect such devices by checking the IC type and product ID numbers and adjusting order of operations accordingly. Signed-off-by:
KT Liao <kt.liao@emc.com.tw> Reported-by:
Chris Chiu <chiu@endlessm.com> Reported-by:
Vlad Glagolev <stealth@vaygr.net> Tested-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 410c29df upstream. If a Simple command is sent with a failure, target_setup_cmd_from_cdb returns with TCM_UNSUPPORTED_SCSI_OPCODE or TCM_INVALID_CDB_FIELD. So in the cases where target_setup_cmd_from_cdb returns an error, we never get far enough to call target_execute_cmd to increment simple_cmds. Since simple_cmds isn't incremented, the result of the failure from target_setup_cmd_from_cdb causes transport_generic_request_failure to decrement simple_cmds, due to call to transport_complete_task_attr. With this dev->simple_cmds or dev->dev_ordered_sync is now -1, not 0. So when a subsequent command with an Ordered Task is sent, it causes a hang, since dev->simple_cmds is at -1. Tested-by:
Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by:
Michael Cyr <mikecyr@linux.vnet.ibm.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Mike Christie authored
commit ea263c7f upstream. max_discard_sectors only 32bits, and some non scsi backend devices will set this to the max 0xffffffff, so we can end up overflowing during the max_unmap_lba_count calculation. This fixes a regression caused by my patch: commit 8a9ebe71 Author: Mike Christie <mchristi@redhat.com> Date: Mon Jan 18 14:09:27 2016 -0600 target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors which can result in extra discards being sent to due the overflow causing max_unmap_lba_count to be smaller than what the backing device can actually support. Signed-off-by:
Mike Christie <mchristi@redhat.com> Reviewed-by:
Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 064cdd2d upstream. This patch fixes a race in iscsit_release_commands_from_conn() -> iscsit_free_cmd() -> transport_generic_free_cmd() + wait_for_tasks=1, where CMD_T_FABRIC_STOP could end up being set after the final kref_put() is called from core_tmr_abort_task() context. This results in transport_generic_free_cmd() blocking indefinately on se_cmd->cmd_wait_comp, because the target_release_cmd_kref() check for CMD_T_FABRIC_STOP returns false. To address this bug, make iscsit_release_commands_from_conn() do list_splice and set CMD_T_FABRIC_STOP early while holding iscsi_conn->cmd_lock. Also make iscsit_aborted_task() only remove iscsi_cmd_t if CMD_T_FABRIC_STOP has not already been set. Finally in target_release_cmd_kref(), only honor fabric_stop if CMD_T_ABORTED has been set. Cc: Mike Christie <mchristi@redhat.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Tested-by:
-
Nicholas Bellinger authored
commit 5e2c956b upstream. During transport_generic_free_cmd() with a concurrent TMR ABORT_TASK and shutdown CMD_T_FABRIC_STOP bit set, the caller will be blocked on se_cmd->cmd_wait_stop completion until the final kref_put() -> target_release_cmd_kref() has been invoked to call complete(). However, when ABORT_TASK is completed with FUNCTION_COMPLETE in core_tmr_abort_task(), the aborted se_cmd will have already been removed from se_sess->sess_cmd_list via list_del_init(). This results in target_release_cmd_kref() hitting the legacy list_empty() == true check, invoking ->release_cmd() but skipping complete() to wakeup se_cmd->cmd_wait_stop blocked earlier in transport_generic_free_cmd() code. To address this bug, it's safe to go ahead and drop the original list_empty() check so that fabric_stop invokes the complete() as expected, since list_del_init() can safely be used on a empty list. Cc: Mike Christie <mchristi@redhat.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Tested-by:
-
Nicholas Bellinger authored
commit dff0ca9e upstream. If a command with a Simple task attribute is failed due to a Unit Attention, then a subsequent command with an Ordered task attribute will hang forever. The reason for this is that the Unit Attention status is checked for in target_setup_cmd_from_cdb, before the call to target_execute_cmd, which calls target_handle_task_attr, which in turn increments dev->simple_cmds. However, transport_generic_request_failure still calls transport_complete_task_attr, which will decrement dev->simple_cmds. In this case, simple_cmds is now -1. So when a command with the Ordered task attribute is sent, target_handle_task_attr sees that dev->simple_cmds is not 0, so it decides it can't execute the command until all the (nonexistent) Simple commands have completed. Reported-by:
-
Feng Li authored
commit 8abc718d upstream. In MC/S scenario, the conn->sess has been set NULL in iscsi_login_non_zero_tsih_s1 when the second connection comes here, then kernel panic. The conn->sess will be assigned in iscsi_login_non_zero_tsih_s2. So we should check whether it's NULL before calling. Signed-off-by:
Feng Li <lifeng1519@gmail.com> Tested-by:
Sumit Rai <sumit.rai@calsoftinc.com> Signed-off-by:
-
Iosif Harutyunov authored
commit 714fb87e upstream. Install the UBI device object before we arm sysfs. Otherwise udev tries to read sysfs attributes before UBI is ready and udev rules will not match. Signed-off-by:
Iosif Harutyunov <iharutyunov@sonicwall.com> [rw: massaged commit message] Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Richard Weinberger authored
commit bc743f34 upstream. We cannot use ubi_* logging functions before the UBI object is initialized. Fixes: 32608703 ("UBI: Extend UBI layer debug/messaging capabilities") Signed-off-by:
-
Richard Weinberger authored
commit 4946784b upstream. When the volume resize operation shrinks a volume, LEBs will be unmapped. Since unmapping will not erase these LEBs immediately we have to wait for that operation to finish. Otherwise in case of a power cut right after writing the new volume table the UBI attach process can find more LEBs than the volume table knows. This will render the UBI image unattachable. Fix this issue by waiting for erase to complete and write the new volume table afterward. Reported-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by:
-
Frank Rowand authored
commit d9fc8807 upstream. Fix a memory leak resulting from memory allocation in safe_name(). This patch fixes all call sites of safe_name(). Mathieu Malaterre reported the memory leak on boot: On my PowerMac device-tree would generate a duplicate name: [ 0.023043] device-tree: Duplicate name in PowerPC,G4@0, renamed to "l2-cache#1" in this case a newly allocated name is generated by `safe_name`. However in this case it is never deallocated. The bug was found using kmemleak reported as: unreferenced object 0xdf532e60 (size 32): comm "swapper", pid 1, jiffies 4294892300 (age 1993.532s) hex dump (first 32 bytes): 6c 32 2d 63 61 63 68 65 23 31 00 dd e4 dd 1e c2 l2-cache#1...... ec d4 ba ce 04 ec cc de 8e 85 e9 ca c4 ec cc 9e ................ backtrace: [<c02d3350>] kvasprintf+0x64/0xc8 [<c02d3400>] kasprintf+0x4c/0x5c [<c0453814>] safe_name.isra.1+0x80/0xc4 [<c04545d8>] __of_attach_node_sysfs+0x6c/0x11c [<c075f21c>] of_core_init+0x8c/0xf8 [<c0729594>] kernel_init_freeable+0xd4/0x208 [<c00047e8>] kernel_init+0x24/0x11c [<c00158ec>] ret_from_kernel_thread+0x5c/0x64 Link: https://bugzilla.kernel.org/show_bug.cgi?id=120331Signed-off-by:
Frank Rowand <frank.rowand@am.sony.com> Reported-by: mathieu.malaterre@gmail.com Tested-by:
Mathieu Malaterre <mathieu.malaterre@gmail.com> Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Dotan Barak authored
commit 5b420d9c upstream. When RC, UC, or RAW QPs are created, a qp object is allocated (kzalloc). If at a later point (in procedure create_qp_common) the qp creation fails, this qp object must be freed. Fixes: 1ffeb2eb ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support") Signed-off-by:
Dotan Barak <dotanb@dev.mellanox.co.il> Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Yishai Hadas authored
commit a6100603 upstream. Fix mad send error flow to prevent double freeing address handles, and leaking tx_ring entries when SRIOV is active. If ib_mad_post_send fails, the address handle pointer in the tx_ring entry must be set to NULL (or there will be a double-free) and tx_tail must be incremented (or there will be a leak of tx_ring entries). The tx_ring is handled the same way in the send-completion handler. Fixes: 37bfc7c1 ("IB/mlx4: SR-IOV multiplex and demultiplex MADs") Signed-off-by:
Yishai Hadas <yishaih@mellanox.com> Reviewed-by:
-
Yishai Hadas authored
commit f2940e2c upstream. When calculating the required size of an RC QP send queue, leave enough space for masked atomic operations, which require more space than "regular" atomic operation. Fixes: 6fa8f719 ("IB/mlx4: Add support for masked atomic operations") Signed-off-by:
Jack Morgenstein <jackm@mellanox.co.il> Reviewed-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
-
Mark Bloch authored
commit 5ed935e8 upstream. In case ibnl_put_msg fails in send_nlmsg_done, the function returns with -ENOMEM without freeing. This patch fixes this behavior. Fixes: 30dc5e63 ("RDMA/core: Add support for iWARP Port Mapper user space service") Signed-off-by:
Mark Bloch <markb@mellanox.com> Reviewed-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
-
Erez Shitrit authored
commit 61c78eea upstream. ipoib_neigh_get unconditionally updates the "alive" variable member on any packet send. This prevents the neighbor garbage collection from cleaning out a dead neighbor entry if we are still queueing packets for it. If the queue for this neighbor is full, then don't update the alive timestamp. That way the neighbor can time out even if packets are still being queued as long as none of them are being sent. Fixes: b63b70d8 ("IPoIB: Use a private hash table for path lookup in xmit path") Signed-off-by:
Erez Shitrit <erezsh@mellanox.com> Signed-off-by:
-
Mark Bloch authored
commit 0f377d86 upstream. Fixes a direct call to kfree_skb when nlmsg_free should be used. Fixes: 2ca546b9 ('IB/sa: Route SA pathrecord query through netlink') Signed-off-by:
Ira Weiny <ira.weiny@intel.com> Reviewed-by:
-
Noa Osherovich authored
commit 2788cf3b upstream. FW port-change events are fired on Active <-> non Active port state transitions only. When the port state changes from Active to Initializing (Active -> Down -> Initializing), a single event is fired. The HCA transitions from Down to Initializing unless prevented from doing so, hence the driver should also propagate events when the port state is Initializing to consumers so they'll be aware that the port is no longer Active and act accordingly. Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB...') Signed-off-by:
Noa Osherovich <noaos@mellanox.com> Signed-off-by:
-
Eli Cohen authored
commit c9b25495 upstream. If the caller specified IB_SEND_FENCE in the send flags of the work request and no previous work request stated that the successive one should be fenced, the work request would be executed without a fence. This could result in RDMA read or atomic operations failure due to a MR being invalidated. Fix this by adding the mlx5 enumeration for fencing RDMA/atomic operations and fix the logic to apply this. Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by:
Eli Cohen <eli@mellanox.com> Signed-off-by:
-
Noa Osherovich authored
commit 3c4c3774 upstream. Verify that number of entries is less than device capability. Add an appropriate warning message for error flow. Fixes: bde51583 ('IB/mlx5: Add support for resize CQ') Signed-off-by:
Majd Dibbiny <majd@mellanox.com> Signed-off-by:
-
Noa Osherovich authored
commit 0540d814 upstream. Some variables were not initialized properly: max_recv_wr, max_recv_sge, max_send_wr, qp_context and max_inline_data. Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB...') Signed-off-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
-
Noa Osherovich authored
commit 9ea57852 upstream. Number of entries shouldn't be greater than the device's max capability. This should be checked before rounding the entries number to power of two. Fixes: 51ee86a4 ('IB/mlx5: Fix check of number of entries...') Signed-off-by:
-
Artemy Kovalyov authored
commit e3353c26 upstream. Make MODIFY_QP command input structure compliant to specification Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by:
Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by:
-
Hui Wang authored
commit 59ec4b57 upstream. One of the machines has ALC255 on it, another one has ALC298 on it. On the machine with the codec ALC298, it also has the speaker volume problem, so we add the fixup chained to ALC298_FIXUP_SPK_VOLUME rather than adding a group of pin definition in the pin quirk table, since the speak volume problem does not happen on other machines yet. Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Maruthi Srinivas Bayyavarapu authored
commit fd48331f upstream. This commit fixes garbled audio on Bonaire HDMI Signed-off-by:
Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Hui Wang authored
commit dd9aa335 upstream. We have a Dell AIO on which we can't adjust its speaker's volume. The problem is it is connected to a Audio Output node without Amp-out capability. To fix it, we change it to be connnected to a node with Amp-out capability. Signed-off-by:
-
Takashi Iwai authored
commit 33baefe5 upstream. krealloc() doesn't work always properly with __GFP_ZERO flag as expected. For clearing the reallocated area, we need to clear explicitly instead. Reported-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Jia He authored
commit 649920c6 upstream. In powerpc servers with large memory(32TB), we watched several soft lockups for hugepage under stress tests. The call traces are as follows: 1. get_page_from_freelist+0x2d8/0xd50 __alloc_pages_nodemask+0x180/0xc20 alloc_fresh_huge_page+0xb0/0x190 set_max_huge_pages+0x164/0x3b0 2. prep_new_huge_page+0x5c/0x100 alloc_fresh_huge_page+0xc8/0x190 set_max_huge_pages+0x164/0x3b0 This patch fixes such soft lockups. It is safe to call cond_resched() there because it is out of spin_lock/unlock section. Link: http://lkml.kernel.org/r/1469674442-14848-1-git-send-email-hejianet@gmail.comSigned-off-by:
Jia He <hejianet@gmail.com> Reviewed-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by:
Michal Hocko <mhocko@suse.com> Acked-by:
Dave Hansen <dave.hansen@linux.intel.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Hector Palacios authored
commit 144f4c98 upstream. nand_do_write_ops() determines if it is writing a partial page with the formula: part_pagewr = (column || writelen < (mtd->writesize - 1)) When 'writelen' is exactly 1 byte less than the NAND page size the formula equates to zero, so the code doesn't process it as a partial write, although it should. As a consequence the function remains in the while(1) loop with 'writelen' becoming 0xffffffff and iterating endlessly. The bug may not be easy to reproduce in Linux since user space tools usually force the padding or round-up the write size to a page-size multiple. This was discovered in U-Boot where the issue can be reproduced by writing any size that is 1 byte less than a page-size multiple. For example, on a NAND with 2K page (0x800): => nand erase.part <partition> => nand write $loadaddr <partition> 7ff [Editor's note: the bug was added in commit 29072b96, but moved around in commit 66507c7b ("mtd: nand: Add support to use nand_base poi databuf as bounce buffer")] Fixes: 29072b96 ("[MTD] NAND: add subpage write support") Signed-off-by:
Hector Palacios <hector.palacios@digi.com> Acked-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Dan Williams authored
commit df08c32c upstream. The name for a bdi of a gendisk is derived from the gendisk's devt. However, since the gendisk is destroyed before the bdi it leaves a window where a new gendisk could dynamically reuse the same devt while a bdi with the same name is still live. Arrange for the bdi to hold a reference against its "owner" disk device while it is registered. Otherwise we can hit sysfs duplicate name collisions like the following: WARNING: CPU: 10 PID: 2078 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x64/0x80 sysfs: cannot create duplicate filename '/devices/virtual/bdi/259:1' Hardware name: HP ProLiant DL580 Gen8, BIOS P79 05/06/2015 0000000000000286 0000000002c04ad5 ffff88006f24f970 ffffffff8134caec ffff88006f24f9c0 0000000000000000 ffff88006f24f9b0 ffffffff8108c351 0000001f0000000c ffff88105d236000 ffff88105d1031e0 ffff8800357427f8 Call Trace: [<ffffffff8134caec>] dump_stack+0x63/0x87 [<ffffffff8108c351>] __warn+0xd1/0xf0 [<ffffffff8108c3cf>] warn_slowpath_fmt+0x5f/0x80 [<ffffffff812a0d34>] sysfs_warn_dup+0x64/0x80 [<ffffffff812a0e1e>] sysfs_create_dir_ns+0x7e/0x90 [<ffffffff8134faaa>] kobject_add_internal+0xaa/0x320 [<ffffffff81358d4e>] ? vsnprintf+0x34e/0x4d0 [<ffffffff8134ff55>] kobject_add+0x75/0xd0 [<ffffffff816e66b2>] ? mutex_lock+0x12/0x2f [<ffffffff8148b0a5>] device_add+0x125/0x610 [<ffffffff8148b788>] device_create_groups_vargs+0xd8/0x100 [<ffffffff8148b7cc>] device_create_vargs+0x1c/0x20 [<ffffffff811b775c>] bdi_register+0x8c/0x180 [<ffffffff811b7877>] bdi_register_dev+0x27/0x30 [<ffffffff813317f5>] add_disk+0x175/0x4a0 Reported-by:
Yi Zhang <yizhan@redhat.com> Tested-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Jens Axboe <axboe@fb.com>
-
Paolo Valente authored
commit 20bd723e upstream. When a bio is cloned, the newly created bio must be associated with the same blkcg as the original bio (if BLK_CGROUP is enabled). If this operation is not performed, then the new bio is not associated with any group, and the group of the current task is returned when the group of the bio is requested. Depending on the cloning frequency, this may cause a large percentage of the bios belonging to a given group to be treated as if belonging to other groups (in most cases as if belonging to the root group). The expected group isolation may thereby be broken. This commit adds the missing association in bio-cloning functions. Fixes: da2f0f74 ("Btrfs: add support for blkio controllers") Signed-off-by:
Paolo Valente <paolo.valente@linaro.org> Reviewed-by:
Nikolay Borisov <kernel@kyup.com> Reviewed-by:
Jeff Moyer <jmoyer@redhat.com> Acked-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
James Hogan authored
commit 6154c187 upstream. The LNKGET based atomic sequence in __cmpxchg_u32 has slightly incorrect constraints for the return value which under certain circumstances can allow an address unit register to be used as the first operand of a CMP instruction. This isn't a valid instruction however as the encodings only allow a data unit to be specified. This would result in an assembler error like the following: Error: failed to assemble instruction: "CMP A0.2,D0Ar6" Fix by changing the constraint from "=&da" (assigned, early clobbered, data or address unit register) to "=&d" (data unit register only). The constraint for the second operand, "bd" (an op2 register where op1 is a data unit register and the instruction supports O2R) is already correct assuming the first operand is a data unit register. Other cases of CMP in inline asm have had their constraints checked, and appear to all be fine. Fixes: 6006c0d8 ("metag: Atomics, locks and bitops") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Signed-off-by:
-
Laura Abbott authored
commit b2e1c26f upstream. glibc recently did a sync up (94e73c95d9b5 "elf.h: Sync with the gabi webpage") that added a #define for EM_METAG but did not add relocations This triggers build errors: scripts/recordmcount.c: In function 'do_file': scripts/recordmcount.c:466:28: error: 'R_METAG_ADDR32' undeclared (first use in this function) case EM_METAG: reltype = R_METAG_ADDR32; ^~~~~~~~~~~~~~ scripts/recordmcount.c:466:28: note: each undeclared identifier is reported only once for each function it appears in scripts/recordmcount.c:468:20: error: 'R_METAG_NONE' undeclared (first use in this function) rel_type_nop = R_METAG_NONE; ^~~~~~~~~~~~ Work around this change with some more #ifdefery for the relocations. Fedora Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1354034 Link: http://lkml.kernel.org/r/1468005530-14757-1-git-send-email-labbott@redhat.com Cc: James Hogan <james.hogan@imgtec.com> Fixes: 00512bdd ("metag: ftrace support") Reported-by:
Ross Burton <ross.burton@intel.com> Signed-off-by:
Laura Abbott <labbott@redhat.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Konstantin Neumoin authored
commit 37cf99e0 upstream. The balloon has a special mechanism that is subscribed to the oom notification which leads to deflation for a fixed number of pages. The number is always fixed even when the balloon is fully deflated. But leak_balloon did not expect that the pages to deflate will be more than taken, and raise a "BUG" in balloon_page_dequeue when page list will be empty. So, the simplest solution would be to check that the number of releases pages is less or equal to the number taken pages. Signed-off-by:
Konstantin Neumoin <kneumoin@virtuozzo.com> Signed-off-by:
Denis V. Lunev <den@openvz.org> CC: Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Mario Kleiner authored
commit 196f954e upstream. This reverts commit 013dd9e0 ("drm/i915/dp: fall back to 18 bpp when sink capability is unknown") This commit introduced a regression into stable kernels, as it reduces output color depth to 6 bpc for any video sink connected to a Displayport connector if that sink doesn't report a specific color depth via EDID, or if our EDID parser doesn't actually recognize the proper bpc from EDID. Affected are active DisplayPort->VGA converters and active DisplayPort->DVI converters. Both should be able to handle 8 bpc, but are degraded to 6 bpc with this patch. The reverted commit was meant to fix Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105331 A followup patch implements a fix for that specific bug, which is caused by a faulty EDID of the affected DP panel by adding a new EDID quirk for that panel. DP 18 bpp fallback handling and other improvements to DP sink bpc detection will be handled for future kernels in a separate series of patches. Please backport to stable. Signed-off-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Acked-by:
Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Ville Syrjälä authored
commit a7b4667a upstream. SNB (and IVB too I suppose) starts to misbehave if the GPU gets stuck in an infinite batch buffer loop. The GPU apparently hogs something critical and CPUs start to lose interrupts and whatnot. We can keep the system limping along by unmasking some interrupts in GEN6_PMINTRMSK. The EI up interrupt has been previously chosen for that task, so let's never mask it. v2: s/gen6_rps_pm_mask/gen6_sanitize_rps_pm_mask/ (Chris) Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93122Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
