Fix EMAC soft reset on 460EX/GT to select the right PHY clock source
before and after the soft reset.

EMAC with PHY should use the clock from PHY during soft reset.
EMAC without PHY should use the internal clock during soft reset.

PPC460EX/GT Embedded Processor Advanced User's Manual
section 28.10.1 Mode Register 0 (EMACx_MR0) states:
Note: The PHY must provide a TX Clk in order to perform a soft reset
of the EMAC. If none is present, select the internal clock
(SDR0_ETH_CFG[EMACx_PHY_CLK] = 1).
After a soft reset, select the external clock.

Without the fix, 460EX/GT-based boards with RGMII PHYs attached to
EMACs experience EMAC interrupt storm and system watchdog reset when
issuing "ifconfig eth0 down" + "ifconfig eth0 up" a few times.
The system enters endless loop of serving emac_irq() with EMACx_ISR
register stuck at value 0x10000000 (Rx parity error).

With the fix, the above issue is no longer observed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver wrongly claimed I/O ports at an address returned by pci_iomap() --
even if it was passed an MMIO address.  Fix this by claiming/releasing all PCI
resources in the PCI driver's probe()/remove() methods instead and get rid of
'must_free_region' flag weirdness (why would Cardbus claim anything for us?).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `cfv_destroy_genpool':
drivers/net/caif/caif_virtio.c:364: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `cfv_create_genpool':
drivers/net/caif/caif_virtio.c:397: undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `macb_free_consistent':
drivers/net/ethernet/cadence/macb.c:878: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:883: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:888: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `macb_alloc_consistent':
drivers/net/ethernet/cadence/macb.c:905: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `macb_tx_interrupt':
drivers/net/ethernet/cadence/macb.c:515: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_tx_error_task':
drivers/net/ethernet/cadence/macb.c:457: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_start_xmit':
drivers/net/ethernet/cadence/macb.c:838: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `at91ether_start':
drivers/net/ethernet/cadence/at91_ether.c:49: undefined reference to `dma_alloc_coherent'
drivers/net/ethernet/cadence/at91_ether.c:60: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `at91ether_interrupt':
drivers/net/ethernet/cadence/at91_ether.c:250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `at91ether_start_xmit':
drivers/net/ethernet/cadence/at91_ether.c:169: undefined reference to `dma_map_single'
drivers/built-in.o: In function `at91ether_close':
drivers/net/ethernet/cadence/at91_ether.c:145: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `ath9k_beacon_generate':
drivers/net/wireless/ath/ath9k/beacon.c:146: undefined reference to `dma_unmap_single'
drivers/net/wireless/ath/ath9k/beacon.c:174: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/beacon.c:176: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath9k_beacon_remove_slot':
drivers/net/wireless/ath/ath9k/beacon.c:252: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_descdma_setup':
drivers/net/wireless/ath/ath9k/init.c:382: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_edma_get_buffers':
drivers/net/wireless/ath/ath9k/recv.c:616: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_get_next_rx_buf':
drivers/net/wireless/ath/ath9k/recv.c:740: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_edma_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:176: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:340: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_buf_link':
drivers/net/wireless/ath/ath9k/recv.c:122: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_tasklet':
drivers/net/wireless/ath/ath9k/recv.c:1275: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:1277: undefined reference to `dma_mapping_error'
drivers/net/wireless/ath/ath9k/recv.c:1283: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_init':
drivers/net/wireless/ath/ath9k/recv.c:226: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:229: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_rx_init':
drivers/net/wireless/ath/ath9k/recv.c:303: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:306: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_tx_complete_buf':
drivers/net/wireless/ath/ath9k/xmit.c:2088: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_txstatus_setup':
drivers/net/wireless/ath/ath9k/xmit.c:2344: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_tx_set_retry':
drivers/net/wireless/ath/ath9k/xmit.c:307: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_tx_setup_buffer':
drivers/net/wireless/ath/ath9k/xmit.c:1887: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/xmit.c:1889: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `dma_free_tx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1141: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `dma_free_rx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1120: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `free_dma_desc_resources':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1159: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `stmmac_init_rx_buffers':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:980: undefined reference to `dma_map_single'
drivers/built-in.o: In function `init_dma_desc_rings':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1015: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `stmmac_tx_clean':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2044: undefined reference to `dma_unmap_single'
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2082: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx_refill':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1967: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_xmit':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1845: undefined reference to `dma_map_single'
drivers/built-in.o: In function `skb_frag_dma_map':
include/linux/skbuff.h:2184: undefined reference to `dma_map_page'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/ring_mode.c:40: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:48: undefined reference to `dma_map_single'
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:55: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `xgmac_xmit':
drivers/net/ethernet/calxeda/xgmac.c:1102: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

We have seen multiple NULL dereferences in __inet6_lookup_established()

After analysis, I found that inet6_sk() could be NULL while the
check for sk_family == AF_INET6 was true.

Bug was added in linux-2.6.29 when RCU lookups were introduced in UDP
and TCP stacks.

Once an IPv6 socket, using SLAB_DESTROY_BY_RCU is inserted in a hash
table, we no longer can clear pinet6 field.

This patch extends logic used in commit fcbdf09d
("net: fix nulls list corruptions in sk_prot_alloc")

TCP/UDP/UDPLite IPv6 protocols provide their own .clear_sk() method
to make sure we do not clear pinet6 field.

At socket clone phase, we do not really care, as cloning the parent (non
NULL) pinet6 is not adding a fatal race.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, if macvlan in passthru mode is created and data are rxed and
you remove this device, following panic happens:

NULL pointer dereference at 0000000000000198
IP: [<ffffffffa0196058>] macvlan_handle_frame+0x153/0x1f7 [macvlan]

I'm using following script to trigger this:
<script>
while [ 1 ]
do
	ip link add link e1 name macvtap0 type macvtap mode passthru
	ip link set e1 up
	ip link set macvtap0 up
	IFINDEX=`ip link |grep macvtap0 | cut -f 1 -d ':'`
	cat /dev/tap$IFINDEX  >/dev/null &
	ip link del dev macvtap0
done
</script>

I run this script while "ping -f" is running on another machine to send
packets to e1 rx.

Reason of the panic is that list_first_entry() is blindly called in
macvlan_handle_frame() even if the list was empty. vlan is set to
incorrect pointer which leads to the crash.

I'm fixing this by protecting port->vlans list by rcu and by preventing
from getting incorrect pointer in case the list is empty.

Introduced by: commit eb06acdc "macvlan: Introduce 'passthru' mode to takeover the underlying device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Included changes:
- fix parsing of user typed protocol string to avoid random memory access in
  some cases
- check pskb_trim_rcsum() return value
- prevent DAT from sending ARP replies when not needed
- reorder the main clean up routine to prevent race conditions
Signed-off-by: David S. Miller <davem@davemloft.net>

EXPORT_SYMBOL and inline directives are contradictory to each other.
The patch fixes this inconsistency.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure that the following steps are taken:

- drop packets sent by the VF with vlan tag
- block packets with vlan tag which are steered to the VF
- drop/block tagged packets when the policy is priority-tagged
- make sure VLAN stripping for received packets is set
- make sure force UP bit for the VF QP is set

Use enum values for all the above instead of numerical bit offsets.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commits e6b6a231 "net/mlx4: Add VF MAC spoof checking support" and
3f7fb021 "net/mlx4: Add set VF default vlan ID and priority support"
missed reporting in the device capabilities dump when these features
are actually supported. Also two too noisy debug messages which produce
message on every QP opened by a VF, were left in the code, fix that.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 4c09eed9 (net: fec: Enable imx6 enet checksum acceleration.)
enables hardware checksum acceleration unconditionally for all fec
variants.  This is inappropriate, because some variants like imx5 have
no such support on hardware.  Consequently, fec is broken on these
platforms.  Fix it by enabling hardware checksum only on imx6q-fec type
of controllers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shahed Shaikh says:

====================
This patch series has following bug fixes:
* Fix a bug in unicast MAC address setting in adapter.
  Driver was not deleting older unicast MAC while adding new one.
* Fix an ethtool stats string array by adding missing string entry
  and fix a typo.
* Fix module paramter description. Bracket ')' was missing.
* Fix port status provided though 'ethtool <device>' for 83xx adapter.
* Fix reset recovery path in case of transmit timeout.
* Fix reset recovery during diagnostic tests by preserving
  current device status information.
* Fix mailbox response handling. Driver was not maintaining poll time properly.
* Fix validation of link event command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

o VF driver that has enabled asynchronous link events
  may not set BIT_8 in the request, if it does not require
  link state in the response.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Fix mailbox response poll time to maximum 5 seconds which
  includes mailbox response time as well as time required for
  processing AEN if any.
o Driver need to read firmware control mailbox register instead
  of host control mailbox register.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o In order to perform reset recovery during diagnostics tests,
  current device status information need to be preserved.
  This patch makes the required changes in diagnostics routines
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o When transmit timeout happens, recovery attempt should start with
  adapter soft reset. If soft reset fails to resume traffic, firmware
  dump will be collected and driver will perform a hard reset of the
  adapter. Reset recovery on 83xx was failing after a hard reset.
  This patch fixes that issue.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Fix display for interface while using 'ethtool <device>' for 83xx adapter
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Add missing information in ethtool statistics information array.
o Fix  the typo in the statistics information string.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Delete previous unicast MAC which is already programmed
  in adapter before setting new unicast MAC
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
Here is a batch of fixes intended for the 3.10 stream.

Amitkumar Karwar provides an mwifiex fix to plug a memory leak when
the driver is unloaded.

Bing Zhao brings an mwifiex fix for some flag handling that leads to
log spam and an unusable interface.

Daniel Drake offers an mwifiex fix for multicast filter setup, to
correctly implement wakeup behaviour for multicast WOL.

Felix Fietkau fixes an ath9k problem that produces logspam and keycache
errors due to a bad return code.

Stanislaw Gruszka produces an fix for a WARNING from ath5k, and an
iwl4965 workaround to stop advertising a feature that doesn't work with
the current mac80211 implementation.

Sujith Manoharan gives us an ath9k fix to reprogram the HW beacon timers
after a TSF update, and an initvals fix for the AR9565 device.

Thommy Jakobsson fixes an rx descriptor underrun on b43.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Pull trivial pstore update from Tony Luck:
 "Couple of pstore cleanups"

It turns out that the kmemdup() conversion ends up being undone by the
fact that the memory block also needed the ecc information (see commit
bd08ec33: "pstore/ram: Restore ecc information block"), so all that
remains after merging is the error return code change.

* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  pstore/ram: fix error return code in ramoops_probe()
  fs: pstore: Replaced calls to kmalloc and memcpy with kmemdup

Pull NVMe driver update from Matthew Wilcox:
 "Lots of exciting new features in the NVM Express driver this time,
  including support for emulating SCSI commands, discard support and the
  ability to submit per-sector metadata with I/Os.

  It's still mostly bugfixes though!"

* git://git.infradead.org/users/willy/linux-nvme: (27 commits)
  NVMe: Use user defined admin ioctl timeout
  NVMe: Simplify Firmware Activate code slightly
  NVMe: Only clear the enable bit when disabling controller
  NVMe: Wait for device to acknowledge shutdown
  NVMe: Schedule timeout for sync commands
  NVMe: Meta-data support in NVME_IOCTL_SUBMIT_IO
  NVMe: Device specific stripe size handling
  NVMe: Split non-mergeable bio requests
  NVMe: Remove dead code in nvme_dev_add
  NVMe: Check for NULL memory in nvme_dev_add
  NVMe: Fix error clean-up on nvme_alloc_queue
  NVMe: Free admin queue on request_irq error
  NVMe: Add scsi unmap to SG_IO
  NVMe: queue usage fixes in nvme-scsi
  NVMe: Set TASK_INTERRUPTIBLE before processing queues
  NVMe: Add a character device for each nvme device
  NVMe: Fix endian-related problems in user I/O submission path
  NVMe: Fix I/O cancellation status on big-endian machines
  NVMe: Fix sparse warnings in scsi emulation
  NVMe: Don't fail initialisation unnecessarily
  ...

Pull ACPICA fixes from Rafael Wysocki:

 - _INI regression fix from Tomasz Nowicki.

 - Fix for a possible memory leak in _OSI support routine from Jung-uk
   Kim.

 - Fix for a possible buffer overflow during field unit read operation
   from Bob Moore.

* tag 'acpi-fixes-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPICA: ACPICA: Fix for _INI regression
  ACPICA: _OSI support: Fix possible memory leak
  ACPICA: Fix possible buffer overflow during a field unit read operation

Pull ARM SoC fixes and straggler patches from Olof Johansson:
 "A collection of fixes for fall out from 3.10 merge window, some build
  fixes and warning cleanups and a small handful of patches that were
  small and contained and made sense to still include in 3.10 (some of
  these have also been in -next since the merge window opened).

  Largest continous series is for OMAP, but there's a handful for other
  platforms.

  For i.MX, one of the patches are framebuffer fixups due to fallout
  during the merge window, and the other removes some stale and broken
  code."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
  ARM: exynos: dts: Fixed vbus-gpios
  ARM: EXYNOS5: Fix kernel dump in AFTR idle mode
  ARM: ux500: Rid ignored return value of regulator_enable() compiler warning
  ARM: ux500: read the correct soc_id number
  ARM: exynos: dts: cros5250: add cyapa trackpad
  video: mxsfb: Adapt to new videomode API
  ARM: imx: Select GENERIC_ALLOCATOR
  ARM: imx: compile fix for hotplug.c
  ARM: dts: don't assume boards are using twl4030 for omap3
  ARM: OMAP2+: Remove bogus IS_ERR_OR_NULL checking from id.c
  ARM: dts: Configure and fix the McSPI pins for 4430sdp
  ARM: dts: AM33XX: Add GPMC node
  ARM: dts: OMAP4460: Fix CPU OPP voltages
  ARM: dts: OMAP36xx: Fix CPU OPP voltages
  ARM: OMAP4+: omap2plus_defconfig: Enable audio via TWL6040 as module
  ARM: OMAP2: AM33XX: id: Add support for new AM335x PG2.1 Si
  omap: mux: add AM/DM37x gpios
  ARM: OMAP1: DMA: fix error handling in omap1_system_dma_init()
  ARM: OMAP2+: omap_device: use late_initcall_sync
  ARM: OMAP: RX-51: change probe order of touchscreen and panel SPI devices
  ...

Pull xtensa updates from Chris Zankel:
 "Support for the latest MMU architecture that allows for a larger
  accessible memory region, and various bug-fixes"

* tag 'xtensa-next-20130508' of git://github.com/czankel/xtensa-linux:
  xtensa: Switch to asm-generic/linkage.h
  xtensa: fix redboot load address
  xtensa: ISS: fix timer_lock usage in rs_open
  xtensa: disable IRQs while IRQ handler is running
  xtensa: enable lockdep support
  xtensa: fix arch_irqs_disabled_flags implementation
  xtensa: add irq flags trace support
  xtensa: provide custom CALLER_ADDR* implementations
  xtensa: add stacktrace support
  xtensa: clean up stpill_registers
  xtensa: don't use a7 in simcalls
  xtensa: don't attempt to use unconfigured timers
  xtensa: provide default platform_pcibios_init implementation
  xtensa: remove KCORE_ELF again
  xtensa: document MMUv3 setup sequence
  xtensa: add MMU v3 support
  xtensa: fix ibreakenable register update
  xtensa: fix oprofile building as module

Pull ARC port updates from Vineet Gupta:
 "Support for two new platforms based on ARC700:
   - Abilis TB10x SoC [Chritisian/Pierrick]
   - Simulator only System-C Model [Mischa]

  ARC specific MM improvements:
   - Avoid full TLB flush (ASID increment) on munmap (even single page)
   - VIPT Cache Flushing improvements
     + Delayed dcache flush for non-aliasing dcache (big performance boost)
     + icache flush aliasing agnostic (no need to kill all possible aliases)

  Others:
   - Avoid needless rebuild of DTB files for every kernel build
   - Remove builtin cmdline as that is already provided by DeviceTree/bootargs
   - Fixing unaligned access emulation corner case
   - checkpatch fixes [Sachin]
   - Various fixlets [Noam]
   - Minor build failures/cleanups"

* tag 'arc-v3.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (35 commits)
  ARC: [mm] Lazy D-cache flush (non aliasing VIPT)
  ARC: [mm] micro-optimize page size icache invalidate
  ARC: [mm] remove the pessimistic all-alias-invalidate icache helpers
  ARC: [mm] consolidate icache/dcache sync code
  ARC: [mm] optimise icache flush for kernel mappings
  ARC: [mm] optimise icache flush for user mappings
  ARC: [mm] optimize needless full mm TLB flush on munmap
  ARC: Add support for nSIM OSCI System C model
  ARC: [TB10x] Adapt device tree to new compatible string
  ARC: [TB10x] Add support for TB10x platform
  ARC: [TB10x] Device tree of TB100 and TB101 Development Kits
  ARC: Prepare interrupt code for external controllers
  ARC: Allow embedded arc-intc to be properly placed in DT intc hierarchy
  ARC: [cmdline] Don't overwrite u-boot provided bootargs
  ARC: [cmdline] Remove CONFIG_CMDLINE
  ARC: [plat-arcfpga] defconfig update
  ARC: unaligned access emulation broken if callee-reg dest of LD/ST
  ARC: unaligned access emulation error handling consolidation
  ARC: Debug/crash-printing Improvements
  ARC: fix typo with clock speed
  ...

Pull tile update from Chris Metcalf:
 "The interesting bug fix is support for the upcoming "4.2" release of
  the Tilera hypervisor, which by default launches Linux at privilege
  level 2 instead of 1.  The fix lets new and old hypervisors and
  Linuxes interoperate more smoothly, so I've tagged it for
  stable@kernel.org so that older Linuxes will be able to boot under the
  newer hypervisor."

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  usb: tilegx: fix memleak when create hcd fail
  arch/tile: remove inline marking of EXPORT_SYMBOL functions
  rtc: rtc-tile: add missing platform_device_unregister() when module exit
  tile: support new Tilera hypervisor

Dave reported an oops triggered by trinity:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
  IP: newseg+0x10d/0x390
  PGD cf8c1067 PUD cf8c2067 PMD 0
  Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
  CPU: 2 PID: 7636 Comm: trinity-child2 Not tainted 3.9.0+#67
  ...
  Call Trace:
    ipcget+0x182/0x380
    SyS_shmget+0x5a/0x60
    tracesys+0xdd/0xe2

This bug was introduced by commit af73e4d9 ("hugetlbfs: fix mmap
failure in unaligned size request").
Reported-by: Dave Jones <davej@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Zefan <lizfan@huawei.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The semctl GETNCNT returns the number of semops waiting for the
specified semaphore to become nonzero.  After commit 9f1bc2c9
("ipc,sem: have only one list in struct sem_queue"), the semops waiting
on just one semaphore are waiting on that semaphore's list.

In order to return the correct count, we have to walk that list too, in
addition to the sem_array's list for complex operations.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The semctl GETZCNT returns the number of semops waiting for the
specified semaphore to become zero.  After commit 9f1bc2c9
("ipc,sem: have only one list in struct sem_queue"), the semops waiting
on just one semaphore are waiting on that semaphore's list.

In order to return the correct count, we have to walk that list too, in
addition to the sem_array's list for complex operations.

This bug broke dbench; it works again with this patch applied.
Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Kent Overstreet <koverstreet@google.com>
Tested-by: Kent Overstreet <koverstreet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more vfs fixes from Al Viro:
 "Regression fix from Geert + yet another open-coded kernel_read()"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ecryptfs: don't open-code kernel_read()
  xtensa simdisk: Fix proc_create_data() conversion fallout

The 'samsung,vbus-gpio' was submitted before pinmux landed for
exynos5250 and uses the old-style gpio specifier.  Fix the two
exynos5250 boards that use it.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The kernel crashes while resuming from AFTR idle mode. It happens
because L2 cache was not going into retention state.

This patch configures the USE_RETENTION bit of ARM_L2_OPTION register
so that it does not depend on MANUAL_L2RSTDISABLE_CONTROL of
ARM_COMMON_OPTION register for L2RSTDISABLE signal.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Tested-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.10/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:
Omap device tree fixes for issue discovered during the merge window:

- Fix triggering for GPIO interrupts that's needed for 4430sdp
  Ethernet. Otherwise booting with nfsroot won't work.
- Fix CPU operating point values
- Fix wrong assumption that twl PMIC is always connected to omap3
- Add gpmc for am33xx so beaglebone users can use the bus
- Cosmetic fix for mcspi pin muxing to avoid confusion

* tag 'omap-for-v3.10/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: don't assume boards are using twl4030 for omap3
  ARM: dts: Configure and fix the McSPI pins for 4430sdp
  ARM: dts: AM33XX: Add GPMC node
  ARM: dts: OMAP4460: Fix CPU OPP voltages
  ARM: dts: OMAP36xx: Fix CPU OPP voltages
  ARM: dts: OMAP4: Fix ethernet IRQ for OMAP4 boards