Skip to content

L
linux
Switch branch/tag
  1. 23 Mar, 2017 2 commits
    • Guenter Roeck's avatar
      usb: hub: Fix error loop seen after hub communication errors · 245b2eec
      Guenter Roeck authored 
      While stress testing a usb controller using a bind/unbind looop, the
following error loop was observed.

usb 7-1.2: new low-speed USB device number 3 using xhci-hcd
usb 7-1.2: hub failed to enable device, error -108
usb 7-1-port2: cannot disable (err = -22)
usb 7-1-port2: couldn't allocate usb_device
usb 7-1-port2: cannot disable (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
** 57 printk messages dropped ** hub 7-1:1.0: activate --> -22
** 82 printk messages dropped ** hub 7-1:1.0: hub_ext_port_status failed (err = -22)

This continues forever. After adding tracebacks into the code,
the call sequence leading to this is found to be as follows.

[<ffffffc0007fc8e0>] hub_activate+0x368/0x7b8
[<ffffffc0007fceb4>] hub_resume+0x2c/0x3c
[<ffffffc00080b3b8>] usb_resume_interface.isra.6+0x128/0x158
[<ffffffc00080b5d0>] usb_suspend_both+0x1e8/0x288
[<ffffffc00080c9c4>] usb_runtime_suspend+0x3c/0x98
[<ffffffc0007820a0>] __rpm_callback+0x48/0x7c
[<ffffffc00078217c>] rpm_callback+0xa8/0xd4
[<ffffffc000786234>] rpm_suspend+0x84/0x758
[<ffffffc000786ca4>] rpm_idle+0x2c8/0x498
[<ffffffc000786ed4>] __pm_runtime_idle+0x60/0xac
[<ffffffc00080eba8>] usb_autopm_put_interface+0x6c/0x7c
[<ffffffc000803798>] hub_event+0x10ac/0x12ac
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40

kick_hub_wq() is called from hub_activate() even after failures to
communicate with the hub. This results in an endless sequence of
hub event -> hub activate -> wq trigger -> hub event -> ...

Provide two solutions for the problem.

- Only trigger the hub event queue if communication with the hub
  is successful.
- After a suspend failure, only resume already suspended interfaces
  if the communication with the device is still possible.

Each of the changes fixes the observed problem. Use both to improve
robustness.
Acked-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: default avatarGuenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      245b2eec
    • Gerd Hoffmann's avatar
      ohci-pci: add qemu quirk · 21a60f6e
      Gerd Hoffmann authored 
      On a loaded virtualization host (dozen guests booting at the same time)
it may happen that the ohci controller emulation doesn't manage to do
timely frame processing, with the result that the io watchdog fires and
considers the controller being dead, even though it's only the emulation
being unusual slow due to the load peak.

So, add a quirk for qemu and don't use the watchdog in case we figure we
are running on emulated ohci.  The virtual ohci controller masquerades
as apple ohci controller, but we can identify it by subsystem id.
Signed-off-by: default avatarGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      21a60f6e
  3. 17 Mar, 2017 19 commits
  5. 16 Mar, 2017 8 commits
  7. 12 Mar, 2017 5 commits
    • Linus Torvalds's avatar
      Linux 4.11-rc2 · 4495c08e
      Linus Torvalds authored
      4495c08e
    • Linus Torvalds's avatar
      Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux · 56b24d1b
      Linus Torvalds authored 
      Pull s390 fixes from Martin Schwidefsky:

 - four patches to get the new cputime code in shape for s390

 - add the new statx system call

 - a few bug fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: wire up statx system call
  KVM: s390: Fix guest migration for huge guests resulting in panic
  s390/ipl: always use load normal for CCW-type re-IPL
  s390/timex: micro optimization for tod_to_ns
  s390/cputime: provide archicture specific cputime_to_nsecs
  s390/cputime: reset all accounting fields on fork
  s390/cputime: remove last traces of cputime_t
  s390: fix in-kernel program checks
  s390/crypt: fix missing unlock in ctr_paes_crypt on error path
      56b24d1b
    • Linus Torvalds's avatar
      Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip · 5a45a5a8
      Linus Torvalds authored 
      Pull x86 fixes from Thomas Gleixner:

 - a fix for the kexec/purgatory regression which was introduced in the
   merge window via an innocent sparse fix. We could have reverted that
   commit, but on deeper inspection it turned out that the whole
   machinery is neither documented nor robust. So a proper cleanup was
   done instead

 - the fix for the TLB flush issue which was discovered recently

 - a simple typo fix for a reboot quirk

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tlb: Fix tlb flushing when lguest clears PGE
  kexec, x86/purgatory: Unbreak it and clean it up
  x86/reboot/quirks: Fix typo in ASUS EeeBook X205TA reboot quirk
      5a45a5a8
    • Linus Torvalds's avatar
      Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip · ecade114
      Linus Torvalds authored 
      Pull irq fixes from Thomas Gleixner:

 - a workaround for a GIC erratum

 - a missing stub function for CONFIG_IRQDOMAIN=n

 - fixes for a couple of type inconsistencies

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/crossbar: Fix incorrect type of register size
  irqchip/gicv3-its: Add workaround for QDF2400 ITS erratum 0065
  irqdomain: Add empty irq_domain_check_msi_remap
  irqchip/crossbar: Fix incorrect type of local variables
      ecade114
    • Daniel Borkmann's avatar
      x86/tlb: Fix tlb flushing when lguest clears PGE · 2c4ea6e2
      Daniel Borkmann authored 
      Fengguang reported random corruptions from various locations on x86-32
after commits d2852a22 ("arch: add ARCH_HAS_SET_MEMORY config") and
9d876e79 ("bpf: fix unlocking of jited image when module ronx not set")
that uses the former. While x86-32 doesn't have a JIT like x86_64, the
bpf_prog_lock_ro() and bpf_prog_unlock_ro() got enabled due to
ARCH_HAS_SET_MEMORY, whereas Fengguang's test kernel doesn't have module
support built in and therefore never had the DEBUG_SET_MODULE_RONX setting
enabled.

After investigating the crashes further, it turned out that using
set_memory_ro() and set_memory_rw() didn't have the desired effect, for
example, setting the pages as read-only on x86-32 would still let
probe_kernel_write() succeed without error. This behavior would manifest
itself in situations where the vmalloc'ed buffer was accessed prior to
set_memory_*() such as in case of bpf_prog_alloc(). In cases where it
wasn't, the page attribute changes seemed to have taken effect, leading to
the conclusion that a TLB invalidate didn't happen. Moreover, it turned out
that this issue reproduced with qemu in "-cpu kvm64" mode, but not for
"-cpu host". When the issue occurs, change_page_attr_set_clr() did trigger
a TLB flush as expected via __flush_tlb_all() through cpa_flush_range(),
though.

There are 3 variants for issuing a TLB flush: invpcid_flush_all() (depends
on CPU feature bits X86_FEATURE_INVPCID, X86_FEATURE_PGE), cr4 based flush
(depends on X86_FEATURE_PGE), and cr3 based flush.  For "-cpu host" case in
my setup, the flush used invpcid_flush_all() variant, whereas for "-cpu
kvm64", the flush was cr4 based. Switching the kvm64 case to cr3 manually
worked fine, and further investigating the cr4 one turned out that
X86_CR4_PGE bit was not set in cr4 register, meaning the
__native_flush_tlb_global_irq_disabled() wrote cr4 twice with the same
value instead of clearing X86_CR4_PGE in the first write to trigger the
flush.

It turned out that X86_CR4_PGE was cleared from cr4 during init from
lguest_arch_host_init() via adjust_pge(). The X86_FEATURE_PGE bit is also
cleared from there due to concerns of using PGE in guest kernel that can
lead to hard to trace bugs (see bff672e6 ("lguest: documentation V:
Host") in init()). The CPU feature bits are cleared in dynamic
boot_cpu_data, but they never propagated to __flush_tlb_all() as it uses
static_cpu_has() instead of boot_cpu_has() for testing which variant of TLB
flushing to use, meaning they still used the old setting of the host
kernel.

Clearing via setup_clear_cpu_cap(X86_FEATURE_PGE) so this would propagate
to static_cpu_has() checks is too late at this point as sections have been
patched already, so for now, it seems reasonable to switch back to
boot_cpu_has(X86_FEATURE_PGE) as it was prior to commit c109bf95
("x86/cpufeature: Remove cpu_has_pge"). This lets the TLB flush trigger via
cr3 as originally intended, properly makes the new page attributes visible
and thus fixes the crashes seen by Fengguang.

Fixes: c109bf95 ("x86/cpufeature: Remove cpu_has_pge")
Reported-by: default avatarFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: default avatarDaniel Borkmann <daniel@iogearbox.net>
Cc: bp@suse.de
Cc: Kees Cook <keescook@chromium.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: lkp@01.org
Cc: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernrl.org/r/20170301125426.l4nf65rx4wahohyl@wfg-t540p.sh.intel.com
Link: http://lkml.kernel.org/r/25c41ad9eca164be4db9ad84f768965b7eb19d9e.1489191673.git.daniel@iogearbox.netSigned-off-by: default avatarThomas Gleixner <tglx@linutronix.de>
      2c4ea6e2
  9. 11 Mar, 2017 6 commits
    • Linus Torvalds's avatar
      Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm · 106e4da6
      Linus Torvalds authored 
      Pull KVM fixes from Radim Krčmář:
 "ARM updates from Marc Zyngier:
   - vgic updates:
     - Honour disabling the ITS
     - Don't deadlock when deactivating own interrupts via MMIO
     - Correctly expose the lact of IRQ/FIQ bypass on GICv3

   - I/O virtualization:
     - Make KVM_CAP_NR_MEMSLOTS big enough for large guests with many
       PCIe devices

   - General bug fixes:
     - Gracefully handle exception generated with syndroms that the host
       doesn't understand
     - Properly invalidate TLBs on VHE systems

  x86:
   - improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU
     reset

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: do not warn when MSR bitmap address is not backed
  KVM: arm64: Increase number of user memslots to 512
  KVM: arm/arm64: Remove KVM_PRIVATE_MEM_SLOTS definition that are unused
  KVM: arm/arm64: Enable KVM_CAP_NR_MEMSLOTS on arm/arm64
  KVM: Add documentation for KVM_CAP_NR_MEMSLOTS
  KVM: arm/arm64: VGIC: Fix command handling while ITS being disabled
  arm64: KVM: Survive unknown traps from guests
  arm: KVM: Survive unknown traps from guests
  KVM: arm/arm64: Let vcpu thread modify its own active state
  KVM: nVMX: reset nested_run_pending if the vCPU is going to be reset
  kvm: nVMX: VMCLEAR should not cause the vCPU to shut down
  KVM: arm/arm64: vgic-v3: Don't pretend to support IRQ/FIQ bypass
  arm64: KVM: VHE: Clear HCR_TGE when invalidating guest TLBs
      106e4da6
    • Linus Torvalds's avatar
      Merge tag 'extable-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux · 4b050f22
      Linus Torvalds authored 
      Pull extable.h fix from Paul Gortmaker:
 "Fixup for arch/score after extable.h introduction.

  It seems that Guenter is the only one on the planet doing builds for
  arch/score -- we don't have compile coverage for it in linux-next or
  in the kbuild-bot either. Guenter couldn't even recall where he got
  his toolchain, but was kind enough to share it with me so I could
  validate this change and also add arch/score to my build coverage.

  I sat on this a bit in case there was any other fallout in other arch
  dirs, but since this still seems to be the only one, I might as well
  send it on its way"

* tag 'extable-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
  score: Fix implicit includes now failing build after extable change
      4b050f22
    • Linus Torvalds's avatar
      Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random · 84c37c16
      Linus Torvalds authored 
      Pull random updates from Ted Ts'o:
 "Change get_random_{int,log} to use the CRNG used by /dev/urandom and
  getrandom(2). It's faster and arguably more secure than cut-down MD5
  that we had been using.

  Also do some code cleanup"

* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: move random_min_urandom_seed into CONFIG_SYSCTL ifdef block
  random: convert get_random_int/long into get_random_u32/u64
  random: use chacha20 for get_random_int/long
  random: fix comment for unused random_min_urandom_seed
  random: remove variable limit
  random: remove stale urandom_init_wait
  random: remove stale maybe_reseed_primary_crng
      84c37c16
    • Guenter Roeck's avatar
      score: Fix implicit includes now failing build after extable change · 0acf6119
      Guenter Roeck authored 
      After changing from module.h to extable.h, score builds fail with:

  arch/score/kernel/traps.c: In function 'do_ri':
  arch/score/kernel/traps.c:248:4: error: implicit declaration of function 'user_disable_single_step'
  arch/score/mm/extable.c: In function 'fixup_exception':
  arch/score/mm/extable.c:32:38: error: dereferencing pointer to incomplete type
  arch/score/mm/extable.c:34:24: error: dereferencing pointer to incomplete type

because extable.h doesn't drag in the same amount of headers as the
module.h did.  Add in the headers which were implicitly expected.

Fixes: 90858794 ("module.h: remove extable.h include now users have migrated")
Signed-off-by: default avatarGuenter Roeck <linux@roeck-us.net>
[PG: tweak commit log; refresh for sched header refactoring.]
Signed-off-by: default avatarPaul Gortmaker <paul.gortmaker@windriver.com>
      0acf6119
    • Linus Torvalds's avatar
      Merge tag 'tty-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty · 434fd635
      Linus Torvalds authored 
      Pull tty/serial fixes frpm Greg KH:
 "Here are two bugfixes for tty stuff for 4.11-rc2.

  One of them resolves the pretty bad bug in the n_hdlc code that
  Alexander Popov found and fixed and has been reported everywhere. The
  other just fixes a samsung serial driver issue when DMA fails on some
  systems.

  Both have been in linux-next with no reported issues"

* tag 'tty-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: samsung: Continue to work if DMA request fails
  tty: n_hdlc: get rid of racy n_hdlc.tbuf
      434fd635
    • Linus Torvalds's avatar
      Merge tag 'staging-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging · 85298808
      Linus Torvalds authored 
      Pull staging driver fixes from Greg KH:
 "Here are two small build warning fixes for some staging drivers that
  Arnd has found on his valiant quest to get the kernel to build
  properly with no warnings.

  Both of these have been in linux-next this week and resolve the
  reported issues"

* tag 'staging-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: octeon: remove unused variable
  staging/vc04_services: add CONFIG_OF dependency
      85298808
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7